- 05 Dec, 2009 40 commits
-
-
David T.L. Wong authored
Adds support for Maxim MAX2165 silicon tuner. It was tested on Mygica X8558Pro, which has MAX2165, ATBM8830 and CX23885. Signed-off-by:
David T. L. Wong <davidtlwong@gmail.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
David T.L. Wong authored
Adds support for Maxim MAX2165 silicon tuner. It is tested on Mygica X8558Pro, which has MAX2165, ATBM8830 and CX23885 Signed-off-by:
-
Ignacio de Miguel Diaz authored
Add USB ID 1b80:e39d for Sveon STV20 Tuner USB DVB-T HDTV. Signed-off-by:
Ignacio de Miguel Diaz <imigueldiaz@gmail.com> Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
E3C EC168 DVB USB driver Signed-off-by:
-
Antti Palosaari authored
E3C EC100 DVB-T demodulator driver Signed-off-by:
-
Manu Abraham authored
With a lower bandwidth setup, the Transport Stream gets corrupted due to TSFIFO overrun. The patch fixes the issue. The issue is seen with Transport Streams having a Symbol Rate of 22MSPS and/or greater. Signed-off-by:
Manu Abraham <manu@linuxtv.org> Signed-off-by:
-
Andreas Regel authored
It had always the value 3 no matter what frequency was given. Signed-off-by:
Andreas Regel <andreas.regel@gmx.de> Signed-off-by:
-
Andreas Regel authored
While here, also do some blind scan related fixes. Signed-off-by:
-
Andreas Regel authored
V4L/DVB (13358): stv090x: add an additional check for packet delineator lock in stv090x_read_status in case of a tuned DVB-S2 signal Signed-off-by:
-
Andreas Regel authored
Signed-off-by:
-
Andreas Regel authored
This patch contains several fixes for the stv090x driver: - added missing else - use calculated timeout instead of fixed one - use correct frequency when doing zigzag scan - added missing read of GENCFG register Signed-off-by:
-
Andreas Regel authored
V4L/DVB (13355): stv090x: fixes calculation of AGC2 and uses a different AGC2 threshold for cut 3 chips Signed-off-by:
-
Andreas Regel authored
Signed-off-by:
-
Andreas Regel authored
V4L/DVB (13353): stv090x: fixes STR and SNR calculation and normalizes the value into the 0..0xFFFF range Signed-off-by:
-
Andreas Regel authored
Signed-off-by:
-
Andreas Regel authored
Signed-off-by:
-
Michael Krufky authored
The IR on the HVR-1290 is identical to that of the HVR-1850 Signed-off-by:
Michael Krufky <mkrufky@kernellabs.com> Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Igor M. Liplianin authored
Patch 4 of 4. Also patch changes logic to prevent code repetitions and big indents. It makes checkpatch silent :) Signed-off-by:
Igor M. Liplianin <liplianin@netup.ru> Signed-off-by:
-
Igor M. Liplianin authored
Patch 3 of 4. Also patch changes logic to prevent code repetitions and big indents. It makes checkpatch silent :) Signed-off-by:
-
Igor M. Liplianin authored
Patch 2 of 4. Also patch changes logic to prevent code repetitions and big indents. It makes checkpatch silent :) Signed-off-by:
-
Igor M. Liplianin authored
Patch 1 of 4. Also patch changes logic to prevent code repetitions and big indents. It makes checkpatch silent :) Signed-off-by:
-
Igor M. Liplianin authored
Signed-off-by:
-
Igor M. Liplianin authored
Signed-off-by:
-
Abylay Ospan authored
Signed-off-by:
Abylay Ospan <aospan@netup.ru> Signed-off-by:
-
Abylay Ospan authored
It has positive effect for NetUP Dual DVB-S2 CI card. Signed-off-by:
-
Devin Heitmueller authored
On particularly weak signals, changing register 0xab after setting the interleave mode will cause the FEC lock to get lost (while still holding the EQ lock). So remove the write entirely, which seems to have had no adverse effect in either of my ClearQAM environments (and in particular resolves the customer's reported issue). Also flip around the order of the amhum optimization and the interleave setup to be consistent with the windows driver, which has the side-benefit of doing them both in the same call (since the amhum optimization can only be done once the interleave setup). This work was sponsored by ONELAN Limited. Signed-off-by:
Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by:
-
Devin Heitmueller authored
The HVR-1600 doesn't use the standard mechanism for computing the gain when in QAM mode, instead always forcing it to be 0x02. Provide the ability to override the algorithm on a per-board basis. This change results in an improvement of 0.4-0.6 dB for QAM tuning. This work was sponsored by ONELAN Limited. Cc: Steven Toth <stoth@kernellabs.com> Signed-off-by:
-
Devin Heitmueller authored
The sh51409 driver was only doing the QAM optimization a single time, and it would only occur if you received a lock instantaneously after the tuning request. Restructure the code so that the optimization occurs once you reach a signal lock. Note that this depends on the caller polling for status, but we don't have much choice at this point without an independent thread monitoring the lock status. Also, at this point pretty much every application polls for status lock after doing the tune, so the likelihood of the optimization not occurring in the real world is pretty low. The state machine has also been reworked such that setting the interleave mode is now a dependency of doing the QAM optimization. Before both were mutually exclusive, which was not consistent with the Windows driver. We now have a single state machine that controls both. The changes as-is are only enabled for the HVR-1600. Once the changes are tested with some of the other boards, this change should be made generic and the "_legacy" functions should be removed. This work was sponsored by ONELAN Limited. Signed-off-by:
-
Devin Heitmueller authored
Perform some optimization of the register configuration based on a trace of the HVR-1600 Windows i2c traffic (and consultation with Steven Toth). Note that some of these values may be able to be moved into the common driver, but I am holding off on that until they can be tested with other boards. This work was sponsored by ONELAN Limited. Cc: Steven Toth <stoth@kernellabs.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
It seems that some patch broke alt modprobe parameter. Fix it to allow changing alternate interfaces during module load and at runtime. If changed during runtime, you'll need to stop a and restart stream for the parameter to be used. Signed-off-by: -
Marton Nemeth authored
The reg_w_seq() function expects the sequence length in entries and not in bytes. One entry in init_7302 and init_7311 is two bytes and not one. Signed-off-by:
Marton Nemeth <nm127@freemail.hu> Signed-off-by:
Jean-Francois Moine <moinejf@free.fr> Signed-off-by:
-
Marton Nemeth authored
The function usb_control_msg() can return error any time so at least warn the user if an error happens. No message is printed in case of normal operation. Signed-off-by:
-
Jean-Francois Moine authored
- the pb03303x exchanges were the mi0360soc ones - add the new sensor mi0360soc - the new exchanges are taken from the info file of the ms-win driver of the webcams 0ac8:301b and 0ac8:303b (vm30x.inf) Signed-off-by:
-
Laurent Pinchart authored
-EINVAL is required by the V4L2 specification. -ENODEV is simply wrong as the device exists. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Laurent Pinchart authored
The MSI StarCam 370i (1b3b:2951) requires the MINMAX quirk. Add a corresponding entry in the device IDs list. Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
