- 02 Feb, 2015 6 commits
-
-
Alexandre Belloni authored
at91_boot_soc and at91_init_soc structures are not used by any SoC, remove their use. Also remove all the now empty SoC files. Signed-off-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> [nicolas.ferre@atmel.com: different organization of the patches] Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com>
-
Nicolas Ferre authored
For sama5d4, remove an indirection and the remaining need for at91_boot_soc structure. This will allow further cleanup. Signed-off-by: -
Alexandre Belloni authored
Only use SOC_AT91SAM9 for all the at91sam9 SoCs. It removes all the empty at91sam9xxx.c SoC files. It also removes the useless at91_init_soc affectation procedure and its "init" function pointer. Only the SoC detection and display are kept for the at91sam9: at91_soc_is_enabled() and at91_boot_soc.map_io() function calls are also removed. It enables HAVE_AT91_SMD and HAVE_AT91_UTMI for all the sam9 SoCs but this only represents 96 bytes of uncompressed kernel code. Signed-off-by:
-
Alexandre Belloni authored
Setup arm_pm_idle and arm_pm_restart function pointers from rm9200_dt_device_init() function to simplify the at91rm9200 initialization process. This same move is already done for the sam9s. Signed-off-by:
-
Nicolas Ferre authored
-
Nicolas Ferre authored
-
- 26 Jan, 2015 9 commits
-
-
Alexandre Belloni authored
The SOC_AT91SAM9263 is being removed, stop using it. Signed-off-by:
-
Alexandre Belloni authored
mach/system_rev.h is not used, remove it. Signed-off-by:
-
Alexandre Belloni authored
In order to remove SOC_SAM9xxx options, stop using HAVE_AT91_DBGUx. Signed-off-by:
-
Nicolas Ferre authored
The PM initialization needs internal SRAM for allocating a gen_pool and use it to store its PM code. So we need to have of_platform_populate() before this code. Suggested-by:
-
Alexandre Belloni authored
As all sam9 SoCs are setting arm_pm_idle to at91sam9_idle(), do it from sam9_dt_device_init(). Signed-off-by:
Arnd Bergmann <arnd@arndb.de> [nicolas.ferre@atmel.com: adapt patch to newer series] Signed-off-by:
-
Alexandre Belloni authored
sam9n12 and sam9x5 don't set arm_pm_idle because of an oversight, fix that. Signed-off-by:
-
Alexandre Belloni authored
As long as there is no other non-const variable marked __initdata in the same compilation unit it doesn't hurt. If there were one however compilation would fail with error: $variablename causes a section type conflict because a section containing const variables is marked read only and so cannot contain non-const variables. Signed-off-by:
-
Nicolas Ferre authored
Newer SoCs: at91sam9x5, at91sam9n12, sama5d3 and sama5d4 embed a DDR controller and have a different PMC status register layout than the at91sam9g45. Create another at91_sam9x5_pm_init() function to match this compatibility. Signed-off-by: -
Nicolas Ferre authored
The DEBUG_AT91_UART Kconfig option was forgotten when moving the AT91 debug-macro.S file. Add it and use it for the at91.S compilation. Reported-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
-
- 16 Jan, 2015 9 commits
-
-
Alexandre Belloni authored
Move at91rm9200_idle() along with at91sam9_idle() in clk/at91/pmc.c. Signed-off-by:
Michael Turquette <mturquette@linaro.org> Signed-off-by:
-
Alexandre Belloni authored
SRAM initialization is now done through the mmio-sram driver and at91_init_sram() is not called anymore, remove it. Signed-off-by:
-
Alexandre Belloni authored
Signed-off-by:
-
Alexandre Belloni authored
Now that the SRAM is initialized by the mmio-sram driver, .map_io is useless. remove it. Signed-off-by:
-
Alexandre Belloni authored
Split at91_pm_init() in three variants that are called by the respective SoCs .init_machine. This allows to remove the of_machine_is_compatible() calls and move at91_pm_init() out of arch_initcall() which is required for multiplatform. Signed-off-by:
-
Alexandre Belloni authored
Check UDP and UHP on sam9x5, sam9n12 and the sama5 series. Check UHP on the sam9g45. Signed-off-by:
-
Alexandre Belloni authored
Now that the SRAM is part of a genpool, use it to allocate memory to use for the slowclock implementation. Signed-off-by:
-
Alexandre Belloni authored
Store SoC differences in a struct to remove cpu_is_* usage. Signed-off-by:
-
Nicolas Ferre authored
-
- 15 Jan, 2015 16 commits
-
-
Josh Wu authored
According to v4l2 dt document, we add: a camera host: ISI port. a i2c camera sensor: ov2640 port. to sama5d3xmb.dtsi. The ov2640 node defines the pinctrls, clocks and refer to isi port. The ISI node also has a reference to the ov2640 port. Signed-off-by:
Josh Wu <josh.wu@atmel.com> Acked-by:
-
Josh Wu authored
For sama5d3xmb board, the pins: pinctrl_isi_pck_as_mck is pck1, and used to provide MCK for camera sensor. We change its name to: pinctrl_pck1_as_isi_mck. As we want camera sensor instead of ISI to configure the pck1 (ISI_MCK) pin. So we remove this pinctrl from ISI DT node. It will be added in sensor's DT node. Signed-off-by:
-
Josh Wu authored
For sama5d3xmb board, the pins: pinctrl_isi_{power,reset} is used to power-down or reset camera sensor. So we should let camera sensor instead of ISI to configure the pins. This patch will change pinctrl name from pinctrl_isi_{power,reset} to pinctrl_sensor_{power,reset}. And remove these two pinctrl from ISI's DT node. We will add these two pinctrl to sensor's DT node. Signed-off-by: -
Bo Shen authored
The mck is decided by the board design, move it to mb related dtsi file. Signed-off-by:
Bo Shen <voice.shen@atmel.com> Acked-by:
-
Bo Shen authored
The ISI has 12 data lines, add the missing two data lines. Signed-off-by:
-
Bo Shen authored
As the ISI has 12 data lines, however we only use 8 data lines with sensor module. So, split the data line into two groups which make it can be choosed depends on the hardware design. Signed-off-by:
-
Josh Wu authored
Add ISI peripheral clock in sama5d3.dtsi. Signed-off-by:
-
Alexandre Belloni authored
The ethernut5 is actually based on an at91sam9xe, use the correct dts include. Cc: Martin Reimann <martin.reimann@egnite.de> Cc: Tim Schendekehl <tim.schendekehl@egnite.de> Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by:
-
Alexandre Belloni authored
at91sam9xe is slightly different from at91sam9260, in particular it has a different SRAM size and location. Signed-off-by:
-
Alexandre Belloni authored
Add nodes for the SRAM available on atmel SoCs For the at91sam9260 and the at91sam9g20, address mirroring is used to create a single contiguous SRAM range instead of declaring two separate banks. Also remove leftover TODOs in the sam9g45 file Signed-off-by:
-
Alexandre Belloni authored
Enable the RTC on the at91rm9200ek. Signed-off-by:
-
Alexandre Belloni authored
Add a node for the RTC available on at91rm9200. Signed-off-by:
-
Alexandre Belloni authored
Add node for the RTC available on the at91sam9n12. Signed-off-by:
-
Alexandre Belloni authored
Since all rm9200 board files have been removed, there is no user of at91rm9200_set_type() left. Remove it Signed-off-by:
-
Alexandre Belloni authored
at91rm9200_dt_initialize() is doing the same as at91_dt_initialize(), use that one instead. Signed-off-by:
-
Alexandre Belloni authored
Move debug-macro.S from include/mach/ to include/debug where all other common debug macros are. Signed-off-by:
-
