Pci_enable_device() will set device power state to D0,
so it's no need to do it again in dwc3_pci_probe().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

very minor patch fixing the following build warning on
a debug message:

drivers/usb/musb/musb_host.c: In function ‘musb_host_rx’:
drivers/usb/musb/musb_host.c:1763:4: warning: format ‘%x’ \
	expects argument of type ‘unsigned int’, but argument \
	6 has type ‘dma_addr_t’ [-Wformat]
Signed-off-by: Felipe Balbi <balbi@ti.com>

Registered Tegra USB PHY as a separate platform driver.

To synchronize host controller and PHY initialization, used deferred
probe mechanism. As PHY should be initialized before EHCI starts running,
deferred probe of Tegra EHCI driver till PHY probe gets completed.

Got rid of instance number based handling in host driver.

Made use of DT params to get the PHY Pad registers.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Check return values from all GPIO APIs and handle errors accordingly.

Remove the call to clk_disable_unprepare(); this function does not
prepare or enable the clock, so the error path should not disable or
unprepare it.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

As GPIO information is avail through DT, used it to get Tegra ULPI
reset GPIO number. Added a new member to tegra_usb_phy structure to
store this number.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Added a new PHY mode to support OTG.
Obtained Tegra USB PHY mode using DT property.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In case if clk_get_sys fails, return correct error value provided by
the API.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

ARM: tegra: DT-related fixes needed by the USB tree

The Tegra USB bindings were in bad shape. The patches in this branch
fix the binding definitions, and make all the necessary additions to
the DT files. Stale nodes/properties will be removed early in 3.12
once the USB driver has been updated for the new binding.

These changes are needed in both the USB tree, to allow the driver to
be updated to handle them, and the Tegra tree, so that various tree-
wide DT changes (e.g. conversion of IRQ/GPIO/clock constants to defines)
can be applied on top of them.

* tag 'tegra-for-3.11-deps-for-usb':
  ARM: tegra: update device trees for USB binding rework
  ARM: tegra: modify ULPI reset GPIO properties
  ARM: tegra: finalize USB EHCI and PHY bindings
Signed-of-by: Felipe Balbi <balbi@ti.com>

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds to enable High Speed Inter Chip on Exynos4X12. Both channels
are controlled by usbphy driver based on the patch series of usbphy driver
submitted by Tomasz Figa.

[1] https://patchwork.kernel.org/patch/2576121
[2] https://patchwork.kernel.org/patch/2576131
[3] https://patchwork.kernel.org/patch/2576141
[4] https://patchwork.kernel.org/patch/2576151
[5] https://patchwork.kernel.org/patch/2576161
[6] https://patchwork.kernel.org/patch/2576171Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

'nop_xceiv_dt_ids' is always compiled in. Hence use of
of_match_ptr is unnecessary.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Yu Xu <yuxu@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds driver data for Exynos 4x12 USB 2.0 PHY.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

To remove unnecessary if statements, this patch introduces phy_enable
and phy_disable callbacks in driver data structure that implement
SoC-specific PHY initialization and deinitialization.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch extends driver data structure with set_isolation callback,
which allows to remove the need for checking for SoC type in a switch
statement.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch cleans up handling of reference clock rate in Samsung USB PHY
drivers. It is mostly a cosmetic change but improves error handling in
case of failing to get reference clock or invalid clock rate.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

There is no need to use devm_clk_get to get a clock that is being put
at the end of the function.

This patch changes the code getting reference clock to use clk_get
instead of useless in this case devm_clk_get.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Since phy-samsung-usb library can be used only by phy-samsung-usb2 and
phy-samsung-usb3 drivers, there is no need to give explicit control over
its Kconfig symbol.

This patch makes CONFIG_SAMSUNG_USBPHY symbol hidden and selected
implicitly by CONFIG_SAMSUNG_USB2PHY and CONFIG_SAMSUNG_USB3PHY.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add support for the ab9540 variant of the ab8500 family.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Avinash Kumar <avinash.kumar@stericsson.com>
Cc: Thirupathi Chippakurthy <thirupathi.chippakurthy@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add support for the ab8540 variant of the ab8500 family.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Avinash Kumar <avinash.kumar@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Introduce a "flags" field in "struct ab8500_usb" to allow controlling
driver features and quirks depending on ab8500 chip variant and
revision.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Move each chip's PHY tuning value set code to a separate function to
improve code readability.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add an initial platform_device_id table to the ab8500-usb driver to
allow probing additional variants of the ab8500 family chips.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The driver supports both ab8500 and ab8505, but the actual phy tuning
values logic sets ab8500 values:

if (!is_ab8500_2p0_or_earlier(ab->ab8500))

which is supposed to set values for ab8500, but incorrectly results true
for ab8505 too.

Fix this by adding an additional is_ab8500(ab->ab8500) check.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add an ab8500_usb_restart_phy() function called during probe to ensure
that the AB8500 USB phy is initialized properly even when a cable is
connected at probe time.

Without this fix subsequent host reconnections are not detected
properly.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Sakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add common clock support code for the ab8500-usb phy driver.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Various non functional coding style fixes on ux500_dma.c and
phy-ab8500-usb.c drivers.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Host side dma support for ux500 is enabled by piggybacking on Inventra
dma support.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The streaming endpoint bandwidth parameters are computed are runtime
from module parameters. Remove the corresponding static initializers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

With the hcd is now a direct member of struct musb, we can now simply
eliminate the musb_to_hcd() macro. There aren't that many users left
anyway, as some where already fixed up when parts were factored out to
musb_host.c
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Initialize the host and gadget subsystems of the musb driver only when
the appropriate mode is selected from platform data, or device-tree
information, respectively.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Define MUSB_PORT_MODE_{HOST,GADGET,DUAL_ROLE} and store the
platform-specified value in struct musb.

Note that MUSB_PORT_MODE_HOST has to be set to 1 in order to match
existing device tree bindings which are already documented but in fact
unusued. For information on the bindings, please refer to

  Documentation/devicetree/bindings/usb/omap-usb.txt
  Documentation/devicetree/bindings/usb/am33xx-usb.txt
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch re-introduces the bits that are necessary to use the musb
controller in host mode.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This makes building the actual object files optional to the selected
mode, which saves users who know which kind of USB mode support they
need some binary size.

Unimplemented functions are stubbed out with static inline functions.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The musb struct is currently allocated along with the hcd, which makes
it difficult to build a driver that only acts as gadget device.

Fix this by allocating musb directly, and keep the hcd around as
a pointer in the musb struct.

struct hc_driver musb_hc_driver can now also be static to musb_host.c,
and the macro musb_to_hcd() is just a pointer dereferencer for now, and
will be eliminated later.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This function has its only user in musb_virthub.c, so let's move it
there and make it static.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This will be done from a more appropriate location and as it doesn't
work anyway, it can safely be removed before the other changes.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In particular, this introduces musb_host_resume_root_hub()and
musb_host_poke_root_hub() which will be stubbed out later.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Let the function declarations live in the header files they belong to,
which makes it easier to stub them out later.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>