Introduces ci13xxx_udc_driver struct for bus glue drivers to hint
ci13xxx_udc core about their special requirements.  The flags include
avoiding hardware register access when controller is not in peripheral
mode, enabling pull-up upon VBUS, disabling streaming mode and dependency
on transceiver driver.

Initialize gadget_ops in udc_probe so that transceiver can notify VBUS
presence even when no gadget driver is bounded.

A notify_event callback is embedded in the same struct. This patch implements
two events called CONTROLLER_RESET_EVENT and CONTROLLER_STOPPED_EVENT to
notify the bus glue driver after resetting and stopping the controller for
performing SoC specific quirks.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

dma_alloc_coherent() which is internally called by dma_pool_alloc()
flags a warning if device's coherent DMA mask.  Hence initialize
gadget device's coherent DMA mask to it's parent mask.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

dma_pool_alloc() require sleeping context when called with GFP_KERNEL
argument.  Hence release the spin lock before calling dma_pool_alloc().

usb_ep_alloc_request can also be called with non-atomic GFP flags.  Hence
get rid off spin lock while allocation request memory.

Use GFP_ATOMIC flag for allocating request for ep0 in interrupt handler.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Move PCI bus code from ci13xxx_udc to a new file ci13xxx_pci.  SoC's
which has MIPS USB core can include the ci13xxx_udc and keep bus glue
code in their respective gadget controller drivers.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Implement runtime and system pm ops to put hardware into low power
mode (LPM). As part of LPM, USB clocks are turned off, PHY is put
into suspend state and PHY comparators are turned off if VBUS/Id
notifications are not required from PHY.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Enable runtime PM and mark no_callbacks flag.  OTG device, parent of
HCD takes care of putting hardware into low power mode.  Adjust port
power wakeup flags during system suspend and resume.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds support for EHCI compliant HSUSB Host controller found
on MSM chips.  The root hub has a single port and TT is built into it.
This driver depends on OTG driver for PHY initialization, clock
management and powering up VBUS.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This driver implements PHY initialization, clock management, ULPI IO ops
and simple OTG state machine to kick host/peripheral based on Id/VBUS
line status.  VBUS/Id lines are tied to a reference voltage on some boards.
Hence provide debugfs interface to select host/peripheral mode.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When ASPM PM Feature is enabled on UMI link, devices that use ISOC stream of
data transfer may be exposed to longer latency causing less than optimal per-
formance of the device. The longer latencies are normal and are due to link
wake time coming out of low power state which happens frequently to save
power when the link is not active.
The following code will make exception for certain features of ASPM to be by
passed and keep the logic normal state only when the ISOC device is connected
and active. This change will allow the device to run at optimal performance
yet minimize the impact on overall power savings.
Signed-off-by: Alex He <alex.he@amd.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixes a build failure[1] by adding the missing uaccess.h needed
for copy_from_user and copy_to_user

References:
	http://kisskb.ellerman.id.au/kisskb/buildresult/3607218/Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

If the NOP USB OTG transceiver driver is built as a module, the otg.h
header declares external functions, but if they are referenced from the
kernel proper, as, e.g., in the OMAP3 case, where the omap3evm board is
calling the usb_nop_xceiv_register() function, linkage breaks. This patch
fixes this problem.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

IS_ERR() already implies unlikely(), so it can be omitted here.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fixed coding style issues (delete trailing whitespaces, break
long line)
Signed-off-by: Tobias Ollmann <tobias.ollmann@gmx.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Commit 06c3859f (usb: gadget/imx-udc: remove usage of deprecated symbol
USBD_INT0) was a bit precipitant because the name used instead didn't
match the usual naming scheme for irqs on arm/imx.  I renamed the irq to
the right name in e0830004 (ARM: imx: dynamically allocate imx_udc
device) when 06c3859f didn't hit Linus' tree, so I missed to add a
compat #define.

This patch allows compiling imx_udc.c with and without e0830004.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Annotate whci_hcd_id_table as '__used' to fix following warning:

  CC      drivers/usb/host/whci/hcd.o
drivers/usb/host/whci/hcd.c:359: warning: ‘whci_hcd_id_table’ defined but not used
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* 'sh/ehci' of master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: Convert to USB_ARCH_HAS_OHCI/EHCI selects.
  usb: ehci-sh: Add missing ehci helpers.
  usb: ehci-sh: Fix up fault in shutdown path.
  sh: Add EHCI support for SH7786.
  usb: ehci-hcd: Add support for SuperH EHCI.
  usb: ohci-sh: Set IRQ as shared.

* 'for-next' of git://gitorious.org/usb/usb:
  usb: musb: gadget: prevent a NULL pointer dereference
  usb: musb: add names for IRQs in structure resource
  usb: musb: remove board_data parameter from musb_platform_init()

Annotate i1480_est_id_table as '__used' to fix following warning:

  CC      drivers/uwb/i1480/i1480-est.o
drivers/uwb/i1480/i1480-est.c:94: warning: ‘i1480_est_id_table’ defined but not used
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Annotate whcrc_id_table as '__used' to fix following warning:

  CC      drivers/uwb/whc-rc.o
drivers/uwb/whc-rc.c:452: warning: ‘whcrc_id_table’ defined but not used
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

If g_audio fails to open the sound control device, it crashes at removal:

Insertion:
[ 4143.836536] g_audio gadget: unable to open sound control device file: /dev/snd/controlC0
[ 4143.836543] g_audio gadget: we need at least one control device
[ 4143.836551] g_audio gadget: Linux USB Audio Gadget, version: Dec 18, 2008
[ 4143.836558] g_audio gadget: g_audio ready

Removal:
[ 4146.802643] BUG: unable to handle kernel paging request at 00023018
[ 4146.802655] IP: [<c10af9f5>] filp_close+0xa/0x5b
[ 4146.802674] *pdpt = 0000000015426001 *pde = 0000000000000000
[ 4146.802684] Oops: 0000 [#1] PREEMPT SMP
[ 4146.802692] last sysfs file: /sys/power/state
[ 4146.802701] Modules linked in: g_audio(-) ioh_udc fuse asix usbnet [last unloaded: g_audio]
[ 4146.802719]
[ 4146.802728] Pid: 1394, comm: rmmod Not tainted 2.6.33.5-26.1-ivi #1 To be filled by O.E.M./To be filled by O.E.M.
[ 4146.802738] EIP: 0060:[<c10af9f5>] EFLAGS: 00010206 CPU: 0
[ 4146.802746] EIP is at filp_close+0xa/0x5b
[ 4146.802753] EAX: 00023000 EBX: 00023000 ECX: 00000046 EDX: df842680
[ 4146.802760] ESI: e071cd4c EDI: df842680 EBP: ddbbbef0 ESP: ddbbbee4
[ 4146.802768]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 4146.802776] Process rmmod (pid: 1394, ti=ddbba000 task=dd95a4f0 task.ti=ddbba000)
[ 4146.802782] Stack:
[ 4146.802787]  d540c280 e071cd4c df2bc000 ddbbbefc e071b82c df11e440 ddbbbf04 e071c622
[ 4146.802804] <0> ddbbbf28 e071c47f 00000008 e071cd74 df11e464 df2bc01c df2bc000 e071ce68
[ 4146.802822] <0> 00000880 ddbbbf38 e07fd1b8 e071cef0 00000000 ddbbbf40 e071b9f4 ddbbbf48
[ 4146.802842] Call Trace:
[ 4146.802857]  [<e071b82c>] ? gaudio_cleanup+0x87/0xe0 [g_audio]
[ 4146.802869]  [<e071c622>] ? audio_unbind+0x8/0xc [g_audio]
[ 4146.802881]  [<e071c47f>] ? composite_unbind+0x8d/0xcb [g_audio]
[ 4146.802895]  [<e07fd1b8>] ? usb_gadget_unregister_driver+0x7b/0xc0 [ioh_udc]
[ 4146.802908]  [<e071b9f4>] ? usb_composite_unregister+0x15/0x17 [g_audio]
[ 4146.802920]  [<e071c633>] ? cleanup+0xd/0xf [g_audio]
[ 4146.802932]  [<c105a938>] ? sys_delete_module+0x185/0x1dd
[ 4146.802944]  [<c101c3ea>] ? do_page_fault+0x248/0x276
[ 4146.802956]  [<c10027d0>] ? sysenter_do_call+0x12/0x26
[ 4146.802962] Code: 12 5f 3a 00 8b 43 04 8b 40 0c 0f b3 30 3b 73 44 73 03 89 73 44 89 f8 e8 f1 61 3a 00 5b 5e 5f 5d c3 55 89 e5 57 89 d7 56 53 89 c3 <8b> 40 18 85 c0 75 0f 68 32 15 5e c1 31 f6 e8 52 39 3a 00 5a eb
[ 4146.803058] EIP: [<c10af9f5>] filp_close+0xa/0x5b SS:ESP 0068:ddbbbee4
[ 4146.803071] CR2: 0000000000023018
[ 4146.803112] ---[ end trace 0989a7e023da0434 ]---

This patch makes sure not to assign the_card if gaudio_open_snd_dev fails,
since the parent function will deallocate the card.

Also make sure all filp's in gaudio_open_snd_dev is assigned NULL upon error
and gaudio_close_snd_dev only cleanups when the filp's are non-NULL.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Case we can't allocate struct musb_request,
prevent a NULL pointer dereference by returning
early.
Signed-off-by: Felipe Balbi <balbi@ti.com>

Soon resource data will get automatically
populated from a set of autogenerated data
from TI's hardware database for the OMAP
platform.

Such database, might not have resources at
the expected order by the current drivers.

While we could hack in some exceptions to
that tool to generate resources in a specific
order, it seems less fragile to use the
resource name instead. That way, no matter
what order the resources are generated, the
driver still work.

Modified the OMAP, Blackfin and Davinci
architecture files to add the name of the IRQs
in the resource structures and musb driver to
use the platform_get_irq_byname() api to get
the device and dma irq numbers instead of using
the index.

Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Removed the board_data parameter being
passed to musb_platform_init function
as board_data can be extracted from
device structure which is already member
of musb structure.
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This switches over to selects for the subtypes to enable OHCI/EHCI
support explicitly rather than littering the usb Kconfig with subtype
dependencies.
Suggested-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Merge branch 'omap4-ehci-for-greg' of git://dev.omapzoom.org/pub/scm/anand/linux-omap-usb into usb-next

* 'omap4-ehci-for-greg' of git://dev.omapzoom.org/pub/scm/anand/linux-omap-usb:
  omap4: 4430sdp: enable the ehci port on 4430SDP
  arm: omap4: select USB_ARCH_HAS_EHCI
  arm: omap4: usb: add platform init code for EHCI
  arm: omap4: add USBHOST and related base addresses
  usb: ehci-omap: Add OMAP4 support
  omap: usb: ehci: introduce HSIC mode
  usb: ehci-omap: add helpers for checking port mode
  usb: ehci-omap: use clkdev aliases for functional clocks
  omap: clock: add clkdev aliases for EHCI clocks
  usb: ehci: introduce CONFIG_USB_EHCI_HCD_OMAP
  usb: ehci-omap: don't hard-code TLL channel count
  usb: ehci-omap: update clock names to be more generic

This patch add USB client support Marvell PXA9xx/PXA168 chips. The USB
controller in PXA9xx/PXA168 is a High-Speed OTG controller. The available
endpoints is different between PXA9xx and PXA168.

NOTE:
It is the first version of Marvell PXA9xx/PXA168 USB controller driver.
The support for OTG mode will be added in later patch.
PXA9xx and PXA168 has integrated UTMI PHY in the chips. The initialization
for the PHY is a little different between PXA9xx and PXA168.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Several of the EHCI glue drivers either predate or were merged in the
same timeframe as API changes at the USB core level, resulting in some
missing endpoint_reset and clear_tt_buffer_complete callbacks.

This fixes up all of ehci-atmel, mxc, w90x900, and xilinx-of to tie in
the new helpers, which brings them in line with everyone else.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds test mode support for Langwell gadget driver.
Signed-off-by: Henry Yuan <hang.yuan@intel.com>
Signed-off-by: Andy Luo <yifei.luo@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch modifies the composite gadget to set vbus_draw current limitation
during suspend state. This current limitation in suspend state shouldn't be
more than 2.5mA
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Function twl4030_usb_remove can cause unbalanced regulator disables in
twl4030_phy_power if the cable is not connected. Regulator enable/disable
calls are in balance only if the twl4030_phy_resume was called prior the
twl4030_usb_remove, that is, the cable was connected.

Fix this by checking the 'asleep' variable in twl4030_usb_remove since that
variable is used to check state in other functions.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Some devices (ex ZTE 2726) simply don't respond at all when data is sent
to some of their USB interfaces.  The data gets stuck in the TTYs queue
and sits there until close(2), which them blocks because closing_wait
defaults to 30 seconds (even though the fd is O_NONBLOCK).  This is
rarely desired.  Implement the standard mechanism to adjust closing_wait
and let applications handle it how they want to.
Signed-off-by: Dan Williams <dcbw@redhat.com>

Hi,

The [vk][cmz]alloc(_node) family of functions return void pointers which
it's completely unnecessary/pointless to cast to other pointer types since
that happens implicitly.

This patch removes such casts from drivers/usb/
Signed-off-by: Jesper Juhl <jj@chaosbits.net>

Usually the usbmon returns the amount of data specified in
urb->transfer_buffer_length for output submissions and urb->actual_length
for input callbacks. However, for Isochronous input transfers, this is
not enough, since the returned data buffer may contain "holes".

One easy way to fix this is to use urb->transfer_buffer_length,
but this often transfers a whole lot of unused data, so we find
how much was actually used instead.

Original patch by Márton Németh. See also kernel bug 22182.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The OMAP4 SDP has an SMSC3320 PHY hooked up to EHCI on Port1.
The PHY power is controlled by GPIO 157.

Turn on the PHY power, and register the controller at init.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

The OMAP4 has an on-chip EHCI controller. Select USB_ARCH_HAS_EHCI
to allow the EHCI driver to be built on OMAP4.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

- Add platform init code for EHCI on OMAP4
- Add pad configuration for PHY and TLL modes
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add base addresses for USBHOST, USBTLL, EHCI and OHCI to
the header file.

This will disappear when the drivers are converted to use
the hwmod database, however this patch is needed until then.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Update the ehci-omap glue layer to support the controller in the
OMAP4. Major differences from OMAP3 is that the OMAP4 has per-port
clocking, and supports ULPI output clocking mode. The old input
clocking mode is not supported.

Also, there are only 2 externally available ports as against 3
in the OMAP3. The third port is internally tied off and should
not be used.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>

The EHCI controller in OMAP4 supports a new interface mode - HSIC.
Add this to the list of modes supported on OMAP3.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Introduce helper functions to test port mode. These checks are
performed in several places in the driver, and these helpers
improve readability.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>