Initialization is unneccessary when the variable is written before it is
read. There were some occasions in which the driver would initialize `ret'
during declaration without need.

Purely a cosmetic change with no functional impact.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In some cases where the device is stuck, reading from OTP
can timeout. As OTP section is known there is no need to read
it during device crash dump collection.
Adding a new field to struct fw_map to indicate if to include
this section in crash dump collection.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Talyn-MB introduces various of FW download options:
FW download via PCIe, SPI or PBL for secured access.
The boot and FW download path is determined based on the
OTP HW register. Driver reads this register as part of the
SW reset flow and performs the appropriate initialization
sequence.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add debugfs support for enhanced DMA TX and RX descriptor rings,
TX and RX status rings and RX buffer management.

Run the following command to print the TX and RX status rings:
cat srings

Run the following command in order to select the status ring:
echo STATUS_RING_IDX > dbg_sring_index

Run the following command in order to select the status message:
echo STATUS_MSG_IDX > dbg_status_msg_index

Run the following command in order to print the selected status
message from the selected status ring:
cat status_msg

Run the following command in order to print the RX buffer management
debug information:
cat rx_buff_mgmt
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Enhanced DMA RX data path is handled using a single
RX descriptor ring for all VIFs.
Multiple RX status rings are supported, to allow RSS
and multi MSI support.
The driver gets the RX completions via the RX status rings.
The RX status message includes the completed RX buffer ID,
which points to the allocated SKB.

The enhanced DMA RX data flow supports RX chaining, where
multiple SKBs are merged into a single packet.

Enhanced DMA HW supports RX HW reorder offload, enabled by
default for Talyn-MB.

amsdu_en debugfs entry was added to allow control MSDU aggregation.
Use the following command to disable AMSDU (enabled by default):
echo 0 > amsdu_en
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The enhanced DMA TX data path is handled using a descriptor
ring per connection and a single status ring.

The driver gets TX completions via the TX status ring. Each
status message points to the completed descriptor ring and
includes the number of completed descriptors in this ring.

Non TSO enhanced DMA TX descriptors are similar to legacy DMA
TX descriptors, hence the same transmit function can be used.

However, enhanced DMA TSO frames division is performed by the
HW, hence a new function is added to handle enhanced DMA TSO.
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Enhanced DMA design includes the following rings:
- Single RX descriptor ring is used for all VIFs
- Multiple RX status rings are supported, to allow RSS
- TX descriptor ring is allocated per connection
- A single TX status ring is used for all TX descriptor rings

This patch initializes and frees the above descriptor and
status rings.

The RX SKBs are handled by a new entity of RX buffers manager,
which handles RX buffers, each one points to an allocated SKB.
During Rx completion processing, the driver extracts a buffer
ID which is used as an index to the buffers array.
After the SKB is freed the buffer is moved from the 'active'
list to the 'free' list, indicating it can be used for another
descriptor. During Rx refill, SKBs are allocated and attached
to 'free' buffers. Those buffers are attached to new descriptors
and moved to the 'active' list.

New debugfs entries were added to allow edma configuration:

Run the following command to configure the number of status rings:
echo NUM_OF_STATUS_RINGS > num_rx_status_rings

Run the following command to use extended RX status message for
additional debug fields from HW:
echo 0 > compressed_rx_status

Run the following command to control the size of the TX status ring:
echo TX_STATUS_RING_ORDER > tx_status_ring_order
The status ring size will be 1 << tx_status_ring_order

Run the following command to control the size of the RX status ring:
echo RX_STATUS_RING_ORDER > rx_status_ring_order
Due to HW constrains RX sring order should be bigger than RX ring order
The status ring size will be 1 << rx_status_ring_order

Run the following command to change the number of RX buffer IDs:
echo RX_BUFF_ID_COUNT > rx_buff_id_count
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In enhanced DMA the vrings are handled internally by the FW
and are not exposed to the driver.
Instead, the driver handles descriptor rings, which are mapped
by the FW to vrings.
The completions of the TX and RX descriptors are notified to
the driver using status rings. Each status ring descriptor
includes information of the completed descriptors and the ring id
of their descriptor ring.

This patch changes struct vring to generic wil_ring to allow
its reuse for enhanced DMA descriptor rings and adds the descriptor
and status rings specific descriptors.

The vring debugfs entries have changed as follows:
- dbg_vring_index has changed to dbg_ring_index
- vrings has changed to rings
- vring_idle_trsh has changed to ring_idle_trsh
- vring_index has changed to ring_index
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add changes to support initialization of Talyn-MB wil6210
device:
- Add definition for Talyn-MB new JTAG id
- Define talyn_mb_fw_mapping array
- Add Talyn-MB reset sequence
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Without this, packets larger than 1500 will silently be dropped.
Easily reproduced by sending a ping packet with a size larger
than 1500.
Co-Developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Without this, when receiving a packet that has this flag set
from firmware, we will read invalid trailer data from the packet,
which will be shown as various errors, e.g. "sdio mbox lookahead
is zero" or "invalid rx packet" or "payload length x exceeds max
htc length".
Co-Developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

All packets in a bundle should use the same endpoint id as the
first lookahead.

This matches how things are done is ath6kl, however,
this patch can theoretically handle several bundles
in ath10k_sdio_mbox_rx_process_packets().

Without this patch we get lots of errors about invalid endpoint id:

ath10k_sdio mmc2:0001:1: invalid endpoint in look-ahead: 224
ath10k_sdio mmc2:0001:1: failed to get pending recv messages: -12
ath10k_sdio mmc2:0001:1: failed to process pending SDIO interrupts: -12
Co-Developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In case of WEP encryption, driver has to configure shared key for
associated station(s). Note that sta pointer is NULL in case of non
pairwise key, causing NULL pointer dereference with existing code
(sta_priv->is_data_encrypted). Fix this by using associated sta list
instead. This enables WEP support as client, WEP AP is non-functional.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add list of associated stations(STA, AP, peer...) per vif.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This is an obvious copy & paste bug.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In our environment we are occasionally seeing the following stack trace
in ath10k:

Unable to handle kernel paging request at virtual address 0000a800
pgd = c0204000
[0000a800] *pgd=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in: dwc3 dwc3_of_simple phy_qcom_dwc3 nf_nat xt_connmark
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.31 #2
Hardware name: Generic DT based system
task: c09f4f40 task.stack: c09ee000
PC is at kfree_skb_list+0x1c/0x2c
LR is at skb_release_data+0x6c/0x108
pc : [<c065dcc4>]    lr : [<c065da5c>]    psr: 200f0113
sp : c09efb68  ip : c09efb80  fp : c09efb7c
r10: 00000000  r9 : 00000000  r8 : 043fddd1
r7 : bf15d160  r6 : 00000000  r5 : d4ca2f00  r4 : ca7c6480
r3 : 000000a0  r2 : 01000000  r1 : c0a57470  r0 : 0000a800
Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
Control: 10c5787d  Table: 56e6006a  DAC: 00000051
Process swapper/0 (pid: 0, stack limit = 0xc09ee210)
Stack: (0xc09efb68 to 0xc09f0000)
fb60:                   ca7c6480 d4ca2f00 c09efb9c c09efb80 c065da5c c065dcb4
fb80: d4ca2f00 00000000 dcbf8400 bf15d160 c09efbb4 c09efba0 c065db28 c065d9fc
fba0: d4ca2f00 00000000 c09efbcc c09efbb8 c065db48 c065db04 d4ca2f00 00000000
fbc0: c09efbe4 c09efbd0 c065ddd0 c065db38 d4ca2f00 00000000 c09efc64 c09efbe8
fbe0: bf09bd00 c065dd10 00000003 7fffffff c09efc24 dcbfc9c0 01200000 00000000
fc00: 00000000 00000000 ddb7e440 c09e9440 c09efc48 1d195000 c09efc7c c09efc28
fc20: c027bb68 c028aa00 ddb7e4f8 bf13231c ddb7e454 0004091f bf154571 d4ca2f00
fc40: dcbf8d00 ca7c5df6 bf154538 01200000 00000000 bf154538 c09efd1c c09efc68
fc60: bf132458 bf09bbbc ca7c5dec 00000041 bf154538 bf154539 000007bf bf154545
fc80: bf154538 bf154538 bf154538 bf154538 bf154538 00000000 00000000 000016c1
fca0: 00000001 c09efcb0 01200000 00000000 00000000 00000000 00000000 00000001
fcc0: bf154539 00000041 00000000 00000007 00000000 000000d0 ffffffff 3160ffff
fce0: 9ad93e97 3e973160 7bf09ad9 0004091f d4ca2f00 c09efdb0 dcbf94e8 00000000
fd00: dcbf8d00 01200000 00000000 dcbf8d00 c09efd44 c09efd20 bf132544 bf132130
fd20: dcbf8d00 00000000 d4ca2f00 c09efdb0 00000001 d4ca2f00 c09efdec c09efd48
fd40: bf133630 bf1324d0 ca7c5cc0 000007c0 c09efd88 c09efd70 c0764230 c02277d8
fd60: 200f0113 ffffffff dcbf94c8 bf000000 dcbf93b0 dcbf8d00 00000040 dcbf945c
fd80: dcbf94e8 00000000 c09efdcc 00000000 c09efd90 c09efd90 00000000 00000024
fda0: dcbf8d00 00000000 00000005 dcbf8d00 c09efdb0 c09efdb0 00000000 00000040
fdc0: c09efdec dcbf8d00 dcbfc9c0 c09ed140 00000040 00000000 00000100 00000040
fde0: c09efe14 c09efdf0 bf1739b4 bf132840 dcbfc9c0 ddb82140 c09ed140 1d195000
fe00: 00000001 00000100 c09efe64 c09efe18 c067136c bf173958 ddb7fac8 c09f0d00
fe20: 001df678 0000012c c09efe28 c09efe28 c09efe30 c09efe30 c0a7fb28 ffffe000
fe40: c09f008c 00000003 00000008 c0a598c0 00000100 c09f0080 c09efeb4 c09efe68
fe60: c02096e0 c0671278 c0494584 00000080 dd5c3300 c09f0d00 00000004 001df677
fe80: 0000000a 00200100 dd5c3300 00000000 00000000 c09eaa70 00000060 dd410800
fea0: c09ee000 00000000 c09efecc c09efeb8 c0227944 c02094c4 00000000 00000000
fec0: c09efef4 c09efed0 c0268b64 c02278ac de802000 c09f1b1c c09eff20 c0a16cc0
fee0: de803000 c09ee000 c09eff1c c09efef8 c020947c c0268ae0 c02103dc 600f0013
ff00: ffffffff c09eff54 ffffe000 c09ee000 c09eff7c c09eff20 c021448c c0209424
ff20: 00000001 00000000 00000000 c021ddc0 00000000 00000000 c09f1024 00000001
ff40: ffffe000 c09f1078 00000000 c09eff7c c09eff80 c09eff70 c02103ec c02103dc
ff60: 600f0013 ffffffff 00000051 00000000 c09eff8c c09eff80 c0763cc4 c02103bc
ff80: c09effa4 c09eff90 c025f0e4 c0763c98 c0a59040 c09f1000 c09effb4 c09effa8
ffa0: c075efe0 c025efd4 c09efff4 c09effb8 c097dcac c075ef7c ffffffff ffffffff
ffc0: 00000000 c097d6c4 00000000 c09c1a28 c0a59294 c09f101c c09c1a24 c09f61c0
ffe0: 4220406a 512f04d0 00000000 c09efff8 4220807c c097d95c 00000000 00000000
[<c065dcc4>] (kfree_skb_list) from [<c065da5c>] (skb_release_data+0x6c/0x108)
[<c065da5c>] (skb_release_data) from [<c065db28>] (skb_release_all+0x30/0x34)
[<c065db28>] (skb_release_all) from [<c065db48>] (__kfree_skb+0x1c/0x9c)
[<c065db48>] (__kfree_skb) from [<c065ddd0>] (consume_skb+0xcc/0xd8)
[<c065ddd0>] (consume_skb) from [<bf09bd00>] (ieee80211_rx_napi+0x150/0x82c [mac80211])
[<bf09bd00>] (ieee80211_rx_napi [mac80211]) from [<bf132458>] (ath10k_htt_t2h_msg_handler+0x15e8/0x19c4 [ath10k_core])
[<bf132458>] (ath10k_htt_t2h_msg_handler [ath10k_core]) from [<bf132544>] (ath10k_htt_t2h_msg_handler+0x16d4/0x19c4 [ath10k_core])
[<bf132544>] (ath10k_htt_t2h_msg_handler [ath10k_core]) from [<bf133630>] (ath10k_htt_txrx_compl_task+0xdfc/0x12cc [ath10k_core])
[<bf133630>] (ath10k_htt_txrx_compl_task [ath10k_core]) from [<bf1739b4>] (ath10k_pci_napi_poll+0x68/0xf4 [ath10k_pci])
[<bf1739b4>] (ath10k_pci_napi_poll [ath10k_pci]) from [<c067136c>] (net_rx_action+0x100/0x33c)
[<c067136c>] (net_rx_action) from [<c02096e0>] (__do_softirq+0x228/0x31c)
[<c02096e0>] (__do_softirq) from [<c0227944>] (irq_exit+0xa4/0x114)

The trace points to a corrupt skb inside kfree_skb(), seemingly because
one of the shared skb queues is getting corrupted.  Most of the skb queues
ath10k uses are local to a single call stack, but three are shared among
multiple codepaths:

 - rx_msdus_q,
 - rx_in_ord_compl_q, and
 - tx_fetch_ind_q

Of the three, the first two are manipulated using the unlocked skb_queue
functions without any additional lock protecting them.  Use the locked
variants of skb_queue_* functions to protect these manipulations.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.

Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath9k is the last remaining user of the deprecated getrawmonotonic()
interface. There is nothing wrong with this usage, but migrating
to a timespec64 based interface lets us clean up the old API.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The hardcoded values used in ath10k_mac_tx_push_pending and
ath10k_mac_op_wake_tx_queue set an upper limit of how many packets that
can be consumed from the TX queue.

HTC_HOST_MAX_MSG_PER_TX_BUNDLE is a proper name for this constant, as
the value effectively limits the number of messages that can be consumed
in one step. Thus, the value is an upper limit of the number of messages
that can be added to a TX message bundle.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This define is only used for RX bundling so it is more descriptive if
RX is added to the define-name.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Although the TID mask is 0xf, the modulus operation does still not
produce identical results as the bitwise and operator. If the TID is 15, the
modulus operation will "convert" it to 0, whereas the bitwise and will keep it
as 15.

This was found during code review.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

While debugging driver crashes related to a buggy firmware
crashing under load, I noticed that ath10k_htt_rx_ring_free
could be called without being under lock.  I'm not sure if this
is the root cause of the crash or not, but it seems prudent to
protect it.

Originally tested on 4.16+ kernel with ath10k-ct 10.4 firmware
running on 9984 NIC.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When running iperf on ath10k SDIO, TX can stop working:

iperf -c 192.168.1.1 -i 1 -t 20 -w 10K
[  3]  0.0- 1.0 sec  2.00 MBytes  16.8 Mbits/sec
[  3]  1.0- 2.0 sec  3.12 MBytes  26.2 Mbits/sec
[  3]  2.0- 3.0 sec  3.25 MBytes  27.3 Mbits/sec
[  3]  3.0- 4.0 sec   655 KBytes  5.36 Mbits/sec
[  3]  4.0- 5.0 sec  0.00 Bytes  0.00 bits/sec
[  3]  5.0- 6.0 sec  0.00 Bytes  0.00 bits/sec
[  3]  6.0- 7.0 sec  0.00 Bytes  0.00 bits/sec
[  3]  7.0- 8.0 sec  0.00 Bytes  0.00 bits/sec
[  3]  8.0- 9.0 sec  0.00 Bytes  0.00 bits/sec
[  3]  9.0-10.0 sec  0.00 Bytes  0.00 bits/sec
[  3]  0.0-10.3 sec  9.01 MBytes  7.32 Mbits/sec

There are frames in the ieee80211_txq and there are frames that have
been removed from from this queue, but haven't yet been sent on the wire
(num_pending_tx).

When num_pending_tx reaches max_num_pending_tx, we will stop the queues
by calling ieee80211_stop_queues().

As frames that have previously been sent for transmission
(num_pending_tx) are completed, we will decrease num_pending_tx and wake
the queues by calling ieee80211_wake_queue(). ieee80211_wake_queue()
does not call wake_tx_queue, so we might still have frames in the
queue at this point.

While the queues were stopped, the socket buffer might have filled up,
and in order for user space to write more, we need to free the frames
in the queue, since they are accounted to the socket. In order to free
them, we first need to transmit them.

This problem cannot be reproduced on low-latency devices, e.g. pci,
since they call ath10k_mac_tx_push_pending() from
ath10k_htt_txrx_compl_task(). ath10k_htt_txrx_compl_task() is not called
on high-latency devices.
Fix the problem by calling ath10k_mac_tx_push_pending(), after
processing rx packets, just like for low-latency devices, also in the
SDIO case. Since we are calling ath10k_mac_tx_push_pending() directly,
we also need to export it.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The 5ghz channel parameters of TLV target wasn't passed to host, it caused
host can only use lower channels from 36 to 64.
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Length of WMI scan message was not calculated correctly. The allocated
buffer was smaller than what we expected. So WMI message corrupted
skb_info, which is at the end of skb->data. This fix takes TLV header
into account even if the element is zero-length.

Crash log:
  [49.629986] Unhandled kernel unaligned access[#1]:
  [49.634932] CPU: 0 PID: 1176 Comm: logd Not tainted 4.4.60 #180
  [49.641040] task: 83051460 ti: 8329c000 task.ti: 8329c000
  [49.646608] $ 0   : 00000000 00000001 80984a80 00000000
  [49.652038] $ 4   : 45259e89 8046d484 8046df30 8024ba70
  [49.657468] $ 8   : 00000000 804cc4c0 00000001 20306320
  [49.662898] $12   : 33322037 000110f2 00000000 31203930
  [49.668327] $16   : 82792b40 80984a80 00000001 804207fc
  [49.673757] $20   : 00000000 0000012c 00000040 80470000
  [49.679186] $24   : 00000000 8024af7c
  [49.684617] $28   : 8329c000 8329db88 00000001 802c58d0
  [49.690046] Hi    : 00000000
  [49.693022] Lo    : 453c0000
  [49.696013] epc   : 800efae4 put_page+0x0/0x58
  [49.700615] ra    : 802c58d0 skb_release_data+0x148/0x1d4
  [49.706184] Status: 1000fc03 KERNEL EXL IE
  [49.710531] Cause : 00800010 (ExcCode 04)
  [49.714669] BadVA : 45259e89
  [49.717644] PrId  : 00019374 (MIPS 24Kc)
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath.git patches for 4.19. Major changes:

ath10k

* support channel 173

* fix spectral scan for QCA9984 and QCA9888 chipsets

ath6kl

* add support for Dell Wireless 1537

Pull block fixes from Jens Axboe:
 "A collection of fixes that should go into -rc1. This contains:

   - bsg_open vs bsg_unregister race fix (Anatoliy)

   - NVMe pull request from Christoph, with fixes for regressions in
     this window, FC connect/reconnect path code unification, and a
     trace point addition.

   - timeout fix (Christoph)

   - remove a few unused functions (Christoph)

   - blk-mq tag_set reinit fix (Roman)"

* tag 'for-linus-20180616' of git://git.kernel.dk/linux-block:
  bsg: fix race of bsg_open and bsg_unregister
  block: remov blk_queue_invalidate_tags
  nvme-fabrics: fix and refine state checks in __nvmf_check_ready
  nvme-fabrics: handle the admin-only case properly in nvmf_check_ready
  nvme-fabrics: refactor queue ready check
  blk-mq: remove blk_mq_tagset_iter
  nvme: remove nvme_reinit_tagset
  nvme-fc: fix nulling of queue data on reconnect
  nvme-fc: remove reinit_request routine
  blk-mq: don't time out requests again that are in the timeout handler
  nvme-fc: change controllers first connect to use reconnect path
  nvme: don't rely on the changed namespace list log
  nvmet: free smart-log buffer after use
  nvme-rdma: fix error flow during mapping request data
  nvme: add bio remapping tracepoint
  nvme: fix NULL pointer dereference in nvme_init_subsystem
  blk-mq: reinit q->tag_set_list entry only after grace period

Pull documentation fixes from Mauro Carvalho Chehab:
 "This solves a series of broken links for files under Documentation,
  and improves a script meant to detect such broken links (see
  scripts/documentation-file-ref-check).

  The changes on this series are:

   - can.rst: fix a footnote reference;

   - crypto_engine.rst: Fix two parsing warnings;

   - Fix a lot of broken references to Documentation/*;

   - improve the scripts/documentation-file-ref-check script, in order
     to help detecting/fixing broken references, preventing
     false-positives.

  After this patch series, only 33 broken references to doc files are
  detected by scripts/documentation-file-ref-check"

* tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental: (26 commits)
  fix a series of Documentation/ broken file name references
  Documentation: rstFlatTable.py: fix a broken reference
  ABI: sysfs-devices-system-cpu: remove a broken reference
  devicetree: fix a series of wrong file references
  devicetree: fix name of pinctrl-bindings.txt
  devicetree: fix some bindings file names
  MAINTAINERS: fix location of DT npcm files
  MAINTAINERS: fix location of some display DT bindings
  kernel-parameters.txt: fix pointers to sound parameters
  bindings: nvmem/zii: Fix location of nvmem.txt
  docs: Fix more broken references
  scripts/documentation-file-ref-check: check tools/*/Documentation
  scripts/documentation-file-ref-check: get rid of false-positives
  scripts/documentation-file-ref-check: hint: dash or underline
  scripts/documentation-file-ref-check: add a fix logic for DT
  scripts/documentation-file-ref-check: accept more wildcards at filenames
  scripts/documentation-file-ref-check: fix help message
  media: max2175: fix location of driver's companion documentation
  media: v4l: fix broken video4linux docs locations
  media: dvb: point to the location of the old README.dvb-usb file
  ...

Pull fsnotify updates from Jan Kara:
 "fsnotify cleanups unifying handling of different watch types.

  This is the shortened fsnotify series from Amir with the last five
  patches pulled out. Amir has modified those patches to not change
  struct inode but obviously it's too late for those to go into this
  merge window"

* tag 'fsnotify_for_v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  fsnotify: add fsnotify_add_inode_mark() wrappers
  fanotify: generalize fanotify_should_send_event()
  fsnotify: generalize send_to_group()
  fsnotify: generalize iteration of marks by object type
  fsnotify: introduce marks iteration helpers
  fsnotify: remove redundant arguments to handle_event()
  fsnotify: use type id to identify connector object type

Pull fbdev updates from Bartlomiej Zolnierkiewicz:
 "There is nothing really major here, few small fixes, some cleanups and
  dead drivers removal:

   - mark omapfb drivers as orphans in MAINTAINERS file (Tomi Valkeinen)

   - add missing module license tags to omap/omapfb driver (Arnd
     Bergmann)

   - add missing GPIOLIB dependendy to omap2/omapfb driver (Arnd
     Bergmann)

   - convert savagefb, aty128fb & radeonfb drivers to use msleep & co.
     (Jia-Ju Bai)

   - allow COMPILE_TEST build for viafb driver (media part was reviewed
     by media subsystem Maintainer)

   - remove unused MERAM support from sh_mobile_lcdcfb and shmob-drm
     drivers (drm parts were acked by shmob-drm driver Maintainer)

   - remove unused auo_k190xfb drivers

   - misc cleanups (Souptick Joarder, Wolfram Sang, Markus Elfring, Andy
     Shevchenko, Colin Ian King)"

* tag 'fbdev-v4.18' of git://github.com/bzolnier/linux: (26 commits)
  fb_omap2: add gpiolib dependency
  video/omap: add module license tags
  MAINTAINERS: make omapfb orphan
  video: fbdev: pxafb: match_string() conversion fixup
  video: fbdev: nvidia: fix spelling mistake: "scaleing" -> "scaling"
  video: fbdev: fix spelling mistake: "frambuffer" -> "framebuffer"
  video: fbdev: pxafb: Convert to use match_string() helper
  video: fbdev: via: allow COMPILE_TEST build
  video: fbdev: remove unused sh_mobile_meram driver
  drm: shmobile: remove unused MERAM support
  video: fbdev: sh_mobile_lcdcfb: remove unused MERAM support
  video: fbdev: remove unused auo_k190xfb drivers
  video: omap: Improve a size determination in omapfb_do_probe()
  video: sm501fb: Improve a size determination in sm501fb_probe()
  video: fbdev-MMP: Improve a size determination in path_init()
  video: fbdev-MMP: Delete an error message for a failed memory allocation in two functions
  video: auo_k190x: Delete an error message for a failed memory allocation in auok190x_common_probe()
  video: sh_mobile_lcdcfb: Delete an error message for a failed memory allocation in two functions
  video: sh_mobile_meram: Delete an error message for a failed memory allocation in sh_mobile_meram_probe()
  video: fbdev: sh_mobile_meram: Drop SUPERH platform dependency
  ...

Pull AFS updates from Al Viro:
 "Assorted AFS stuff - ended up in vfs.git since most of that consists
  of David's AFS-related followups to Christoph's procfs series"

* 'afs-proc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  afs: Optimise callback breaking by not repeating volume lookup
  afs: Display manually added cells in dynamic root mount
  afs: Enable IPv6 DNS lookups
  afs: Show all of a server's addresses in /proc/fs/afs/servers
  afs: Handle CONFIG_PROC_FS=n
  proc: Make inline name size calculation automatic
  afs: Implement network namespacing
  afs: Mark afs_net::ws_cell as __rcu and set using rcu functions
  afs: Fix a Sparse warning in xdr_decode_AFSFetchStatus()
  proc: Add a way to make network proc files writable
  afs: Rearrange fs/afs/proc.c to remove remaining predeclarations.
  afs: Rearrange fs/afs/proc.c to move the show routines up
  afs: Rearrange fs/afs/proc.c by moving fops and open functions down
  afs: Move /proc management functions to the end of the file

Pull compat updates from Al Viro:
 "Some biarch patches - getting rid of assorted (mis)uses of
  compat_alloc_user_space().

  Not much in that area this cycle..."

* 'work.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  orangefs: simplify compat ioctl handling
  signalfd: lift sigmask copyin and size checks to callers of do_signalfd4()
  vmsplice(): lift importing iovec into vmsplice(2) and compat counterpart

Pull aio fixes from Al Viro:
 "Assorted AIO followups and fixes"

* 'work.aio' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  eventpoll: switch to ->poll_mask
  aio: only return events requested in poll_mask() for IOCB_CMD_POLL
  eventfd: only return events requested in poll_mask()
  aio: mark __aio_sigset::sigmask const

Pull networking fixes from David Miller:

 1) Various netfilter fixlets from Pablo and the netfilter team.

 2) Fix regression in IPVS caused by lack of PMTU exceptions on local
    routes in ipv6, from Julian Anastasov.

 3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.

 4) Don't crash on poll in TLS, from Daniel Borkmann.

 5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
    including Avahi mDNS. From Bart Van Assche.

 6) Missing of_node_put in qcom/emac driver, from Yue Haibing.

 7) We lack checking of the TCP checking in one special case during SYN
    receive, from Frank van der Linden.

 8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.

 9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.

10) Must grab HW caps before doing quirk checks in stmmac driver, from
    Jose Abreu.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
  net: stmmac: Run HWIF Quirks after getting HW caps
  neighbour: skip NTF_EXT_LEARNED entries during forced gc
  net: cxgb3: add error handling for sysfs_create_group
  tls: fix waitall behavior in tls_sw_recvmsg
  tls: fix use-after-free in tls_push_record
  l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
  l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
  mlxsw: spectrum_switchdev: Fix port_vlan refcounting
  mlxsw: spectrum_router: Align with new route replace logic
  mlxsw: spectrum_router: Allow appending to dev-only routes
  ipv6: Only emit append events for appended routes
  stmmac: added support for 802.1ad vlan stripping
  cfg80211: fix rcu in cfg80211_unregister_wdev
  mac80211: Move up init of TXQs
  mac80211_hwsim: fix module init error paths
  cfg80211: initialize sinfo in cfg80211_get_station
  nl80211: fix some kernel doc tag mistakes
  hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
  rds: avoid unenecessary cong_update in loop transport
  l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
  ...

Pull module updates from Jessica Yu:
 "Minor code cleanup and also allow sig_enforce param to be shown in
  sysfs with CONFIG_MODULE_SIG_FORCE"

* tag 'modules-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
  module: Allow to always show the status of modsign
  module: Do not access sig_enforce directly

Pull uml updates from Richard Weinberger:
 "Minor updates for UML:

   - fixes for our new vector network driver by Anton

   - initcall cleanup by Alexander

   - We have a new mailinglist, sourceforge.net sucks"

* 'for-linus-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Fix raw interface options
  um: Fix initialization of vector queues
  um: remove uml initcalls
  um: Update mailing list address

Merge tag 'riscv-for-linus-4.18-merge_window' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux

Pull RISC-V updates from Palmer Dabbelt:
 "This contains some small RISC-V updates I'd like to target for 4.18.

  They are all fairly small this time. Here's a short summary, there's
  more info in the commits/merges:

   - a fix to __clear_user to respect the passed arguments.

   - enough support for the perf subsystem to work with RISC-V's ISA
     defined performance counters.

   - support for sparse and cleanups suggested by it.

   - support for R_RISCV_32 (a relocation, not the 32-bit ISA).

   - some MAINTAINERS cleanups.

   - the addition of CONFIG_HVC_RISCV_SBI to our defconfig, as it's
     always present.

  I've given these a simple build+boot test"

* tag 'riscv-for-linus-4.18-merge_window' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
  RISC-V: Add CONFIG_HVC_RISCV_SBI=y to defconfig
  RISC-V: Handle R_RISCV_32 in modules
  riscv/ftrace: Export _mcount when DYNAMIC_FTRACE isn't set
  riscv: add riscv-specific predefines to CHECKFLAGS
  riscv: split the declaration of __copy_user
  riscv: no __user for probe_kernel_address()
  riscv: use NULL instead of a plain 0
  perf: riscv: Add Document for Future Porting Guide
  perf: riscv: preliminary RISC-V support
  MAINTAINERS: Update Albert's email, he's back at Berkeley
  MAINTAINERS: Add myself as a maintainer for SiFive's drivers
  riscv: Fix the bug in memory access fixup code

Pull more kvm updates from Paolo Bonzini:
 "Mostly the PPC part of the release, but also switching to Arnd's fix
  for the hyperv config issue and a typo fix.

  Main PPC changes:

   - reimplement the MMIO instruction emulation

   - transactional memory support for PR KVM

   - improve radix page table handling"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (63 commits)
  KVM: x86: VMX: redo fix for link error without CONFIG_HYPERV
  KVM: x86: fix typo at kvm_arch_hardware_setup comment
  KVM: PPC: Book3S PR: Fix failure status setting in tabort. emulation
  KVM: PPC: Book3S PR: Enable use on POWER9 bare-metal hosts in HPT mode
  KVM: PPC: Book3S PR: Don't let PAPR guest set MSR hypervisor bit
  KVM: PPC: Book3S PR: Fix failure status setting in treclaim. emulation
  KVM: PPC: Book3S PR: Fix MSR setting when delivering interrupts
  KVM: PPC: Book3S PR: Handle additional interrupt types
  KVM: PPC: Book3S PR: Enable kvmppc_get/set_one_reg_pr() for HTM registers
  KVM: PPC: Book3S: Remove load/put vcpu for KVM_GET_REGS/KVM_SET_REGS
  KVM: PPC: Remove load/put vcpu for KVM_GET/SET_ONE_REG ioctl
  KVM: PPC: Move vcpu_load/vcpu_put down to each ioctl case in kvm_arch_vcpu_ioctl
  KVM: PPC: Book3S PR: Enable HTM for PR KVM for KVM_CHECK_EXTENSION ioctl
  KVM: PPC: Book3S PR: Support TAR handling for PR KVM HTM
  KVM: PPC: Book3S PR: Add guard code to prevent returning to guest with PR=0 and Transactional state
  KVM: PPC: Book3S PR: Add emulation for tabort. in privileged state
  KVM: PPC: Book3S PR: Add emulation for trechkpt.
  KVM: PPC: Book3S PR: Add emulation for treclaim.
  KVM: PPC: Book3S PR: Restore NV regs after emulating mfspr from TM SPRs
  KVM: PPC: Book3S PR: Always fail transactions in guest privileged state
  ...

Pull virtio updates from Michael Tsirkin:
 "virtio, vhost: features, fixes

   - PCI virtual function support for virtio

   - DMA barriers for virtio strong barriers

   - bugfixes"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio: update the comments for transport features
  virtio_pci: support enabling VFs
  vhost: fix info leak due to uninitialized memory
  virtio_ring: switch to dma_XX barriers for rpmsg