- 26 Apr, 2006 3 commits
-
-
Richard Purdie authored
Signed-off-by:
Richard Purdie <rpurdie@rpsys.net> Signed-off-by:
Dmitry Torokhov <dtor@mail.ru>
-
Imre Deak authored
Providing more accurate coordinates for thumb press requires additional steps in the filtering logic: - Ignore samples found invalid by the debouncing logic, or the ones that have out of bound pressure value. - Add a parameter to repeat debouncing, so that more then two consecutive good readings are required for a valid sample. Signed-off-by:
Imre Deak <imre.deak@nokia.com> Acked-by:
Juha Yrjola <juha.yrjola@nokia.com> Signed-off-by:
-
Imre Deak authored
X touchscreen drivers that don't interpret the designated pen up message assume a pen up event from a pressure value 0. For these we generate a pressure 0 message along with the pen up message. Signed-off-by:
-
- 12 Apr, 2006 6 commits
-
-
Imre Deak authored
The pen down IRQ will toggle during each X,Y,Z measurement cycle. Even though the IRQ is disabled it will be latched and delivered when after enable_irq. Thus in the IRQ handler we must avoid starting a new measurement cycle when such an "unwanted" IRQ happens. Add a get_pendown_state platform function, which will probably determine this by reading the current GPIO level of the pen IRQ pin. Move the IRQ reenabling from the SPI RX function to the timer. After the last power down message the pen IRQ pin is still active for a while and get_pendown_state would report incorrectly a pen down state. When suspending we should check the ts->pending flag instead of ts->pendown, since the timer can be pending regardless of ts->pendown. Also if ts->pending is set we can be sure that the timer is running, so no need to rearm it. Similarly if ts->pending is not set we can be sure that the IRQ is enabled (and the timer is not). Signed-off-by:
David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
Imre Deak authored
- Add disable attribute to support device locking mode where unintentional touch event shouldn't wake up the system; - Update comments; - Add missing spin_lock_init; - Do device resume with the lock held; - Do cleanup calls / free memory in the reverse order of initialization. Signed-off-by:
-
Juha Yrjola authored
Sometimes a polling loop had a hard time changing state without pre-emption enabled. Use msleep instead, it's better anyway. Signed-off-by:
-
Imre Deak authored
Some touchscreens seem to oscillate heavily for a while after touching the screen. Implement support for sampling the screen until we get two consecutive values that are close enough. Signed-off-by:
-
Imre Deak authored
Submit a seperate request for powering down the ADC in ads7846, doing it after the last read request. Otherwise some of the read values are incorrect. Signed-off-by:
-
Imre Deak authored
It's handy for userspace diagnostics to see the pen down status, to see whether the touchscreen is "stuck" (shortcircuited). Signed-off-by:
-
- 05 Apr, 2006 2 commits
-
-
John Reed Riley authored
Signed-off-by: -
Stefan Rompf authored
Signed-off-by:
-
- 02 Apr, 2006 7 commits
-
-
Samuel Thibault authored
- Add KEY_BRL_* input keys and K_BRL_* keycodes; - Add emulation of how braille keyboards usually combine braille dots to the console keyboard driver; - Add handling of unicode U+28xy diacritics. Signed-off-by:
Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by:
-
Richard Thrippleton authored
Toshiba Protege M300 also requires the same workaround as Satellites and Dynabooks - Synaptics report rate should be lowered to 40pps (from 80), otherwise KBC starts losing keypresses. Signed-off-by:
Richard Thrippleton <ret28@cam.ac.uk> Signed-off-by:
-
Raphael Assenat authored
SNES gamepads and mice share the same type of interface so they both can be connected to the parallel port using a simple interface. Adding mouse support to a gamepad driver may sound funny at first, but doing so in this case makes it possible to connect and SNES gamepads and mice at the same time, on the same port. Signed-off-by:
Raphael Assenat <raph@raphnet.net> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
-
Dmitry Torokhov authored
Signed-off-by: -
Dmitry Torokhov authored
Signed-off-by: -
Dmitry Torokhov authored
sysfs can't handle more than PAGE_SIZE data coming from attributes' show() methods; make sure we respect this limit. Signed-off-by: -
Dmitry Torokhov authored
Conflicts: arch/powerpc/kernel/setup-common.c drivers/input/keyboard/hil_kbd.c drivers/input/mouse/hil_ptr.c
-
- 01 Apr, 2006 5 commits
-
-
Linus Torvalds authored
* master.kernel.org:/home/rmk/linux-2.6-serial: [SERIAL] Allow 8250 PCI, PNP, GSC and HP300 support to be disabled
-
Linus Torvalds authored
* master.kernel.org:/home/rmk/linux-2.6-mmc: [MMC] Pass -DDEBUG on compiler command line if MMC_DEBUG selected [MMC] Add OMAP MMC host driver
-
Linus Torvalds authored
* master.kernel.org:/home/rmk/linux-2.6-arm: [ARM] 3424/2: ixp23xx: fix uncompress.h for recent CRLF decompressor change [ARM] 3434/1: pxa i2s amsl define [ARM] 3425/1: xsc3: need to include pgtable-hwdef.h [ARM] Allow un-muxed syscalls to be available for everyone [ARM] 3420/1: Missing clobber in example code [ARM] nommu: fixups for the exception vectors [ARM] nommu: add nommu specific Kconfig and MMUEXT variable in Makefile [ARM] nommu: start-up code [ARM] nommu: MPU support in boot/compressed/head.S
-
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6Linus Torvalds authored
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: [IA64] Avoid "u64 foo : 32;" for gcc3 vs. gcc4 compatibility [IA64] Export cpu cache info by sysfs
-
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/sfrench/cifs-2.6: [CIFS] Fix typo in earlier cifs_unlink change and protect one [CIFS] Incorrect signature sent on SMB Read [CIFS] Fix unlink oops when indirectly called in rename error path [CIFS] Fix two remaining coverity scan tool warnings. [CIFS] Set correct lock type on new posix unlock call [CIFS] Upate cifs change log [CIFS] Fix slow oplock break response when mounts to different [CIFS] Workaround various server bugs found in testing at connectathon [CIFS] Allow fallback for setting file size to Procom SMB server when [CIFS] Make POSIX CIFS Extensions SetFSInfo match exactly what we want [CIFS] Move noisy debug message (triggerred by some older servers) from [CIFS] Use correct pid on new cifs posix byte range lock call [CIFS] Add posix (advisory) byte range locking support to cifs client [CIFS] CIFS readdir perf optimizations part 1 [CIFS] Free small buffers earlier so we exceed the cifs [CIFS] Fix large (ie over 64K for MaxCIFSBufSize) buffer case for wrapping [CIFS] Convert remaining places in fs/cifs from [CIFS] SessionSetup cleanup part 2 [CIFS] fix compile error (typo) and warning in cifssmb.c [CIFS] Cleanup NTLMSSP session setup handling
-
- 31 Mar, 2006 17 commits
-
-
Steve French authored
extra path. Since cifs_unlink can also be called from rename path and there was one report of oops am making the extra check for null inode. Signed-off-by:Steve French <sfrench@us.ibm.com>
-
Steve French authored
Fixes Samba bug 3621 and kernel.org bug 6147 For servers which require SMB/CIFS packet signing, we were sending the wrong signature (all zeros) on SMB Read request. The new cifs routine to do signatures across an iovec was not complete - and SMB Read, unlike the new SMBWrite2, did not fall back to the older routine (ie use SendReceive vs. the more efficient SendReceive2 ie used the older cifs_sign_smb vs. the disabled cifs_sign_smb2) for calculating signatures. This finishes up cifs_sign_smb2/cifs_calc_signature2 so that the callers of SendReceive2 can get SMB/CIFS packet signatures. Now that cifs_sign_smb2 is supported, we could start using it in the write path but this smaller fix does not include the change to use SMBWrite2 when signatures are required (which when enabled will make more Writes more efficient and alloc less memory). Currently Write2 is only used when signatures are not required at the moment but after more testing we will enable that as well). Thanks to James Slepicka and Sam Flory for initial investigation. Signed-off-by: -
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: [NET]: Allow skb headroom to be overridden [TCP]: Kill unused extern decl for tcp_v4_hash_connecting() [NET]: add SO_RCVBUF comment [NET]: Deinline some larger functions from netdevice.h [DCCP]: Use NULL for pointers, comfort sparse. [DECNET]: Fix refcount
-
Jes Sorensen authored
Commit 70674f95: [PATCH] Optimize select/poll by putting small data sets on the stack resulted in the poll stack being 4-byte aligned on 64-bit architectures, causing misaligned accesses to elements in the array. This patch fixes it by declaring the stack in terms of 'long' instead of 'char'. Force alignment of poll and select stacks to long to avoid unaligned access on 64 bit architectures. Signed-off-by:
Jes Sorensen <jes@sgi.com> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Linus Torvalds authored
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: [PATCH] libata: fix ata_xfer_tbl termination [PATCH] libata: make ata_qc_issue complete failed qcs [PATCH] libata: fix ata_qc_issue failure path [PATCH] ata_piix: fix ich6/m_map_db [libata] ahci: add ATI SB600 PCI IDs
-
David Howells authored
The attached patch documents the Linux kernel's memory barriers. I've updated it from the comments I've been given. The per-arch notes sections are gone because it's clear that there are so many exceptions, that it's not worth having them. I've added a list of references to other documents. I've tried to get rid of the concept of memory accesses appearing on the bus; what matters is apparent behaviour with respect to other observers in the system. Interrupts barrier effects are now considered to be non-existent. They may be there, but you may not rely on them. I've added a couple of definition sections at the top of the document: one to specify the minimum execution model that may be assumed, the other to specify what this document refers to by the term "memory". I've made greater mention of the use of mmiowb(). I've adjusted the way in which caches are described, and described the fun that can be had with cache coherence maintenance being unordered and data dependency not being necessarily implicit. I've described (smp_)read_barrier_depends(). I've rearranged the order of the sections, so that memory barriers are discussed in abstract first, and then described the memory barrier facilities available on Linux, before going on to more real-world discussions and examples. I've added information about the lack of memory barriering effects with atomic ops and bitops. I've added information about control dependencies. I've added more diagrams to illustrate caching interactions between CPUs. Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Kirill Korotaev authored
Wrong error path in dup_fd() - it should return NULL on error, not an address of already freed memory :/ Triggered by OpenVZ stress test suite. What is interesting is that it was causing different oopses in RCU like below: Call Trace: [<c013492c>] rcu_do_batch+0x2c/0x80 [<c0134bdd>] rcu_process_callbacks+0x3d/0x70 [<c0126cf3>] tasklet_action+0x73/0xe0 [<c01269aa>] __do_softirq+0x10a/0x130 [<c01058ff>] do_softirq+0x4f/0x60 ======================= [<c0113817>] smp_apic_timer_interrupt+0x77/0x110 [<c0103b54>] apic_timer_interrupt+0x1c/0x24 Code: Bad EIP value. <0>Kernel panic - not syncing: Fatal exception in interrupt Signed-Off-By:
Pavel Emelianov <xemul@sw.ru> Signed-Off-By:
Dmitry Mishin <dim@openvz.org> Signed-Off-By:
Kirill Korotaev <dev@openvz.org> Signed-Off-By:
-
Nicolas Pitre authored
Turn some macros into inline functions and add proper type checking as well as being more readable. Also a minor comment adjustment. Signed-off-by:
Nicolas Pitre <nico@cam.org> Acked-by:
Ingo Molnar <mingo@elte.hu> Signed-off-by:
-
Jesper Juhl authored
Decrease the number of pointer derefs in drivers/serial/jsm/jsm_tty.c Benefits of the patch: - Fewer pointer dereferences should make the code slightly faster. - Size of generated code is smaller - Improved readability Signed-off-by:
Jesper Juhl <jesper.juhl@gmail.com> Acked-by:
"V. ANANDA KRISHNAN" <mansarov@us.ibm.com> Signed-off-by:
-
Adrian Bunk authored
As announced, lookup_hash() can now become static. Signed-off-by:
Adrian Bunk <bunk@stusta.de> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Adrian Bunk authored
The only user of get_wchan is the proc fs - and proc can't be built modular. Signed-off-by:
-
NeilBrown authored
Signed-off-by:
Brad Campbell <brad@wasp.net.au> Signed-off-by:
Neil Brown <neilb@suse.de> Signed-off-by:
-
NeilBrown authored
And remove the comments that were put in inplace of a fix too.... Signed-off-by:
-
NeilBrown authored
Currently a device failure during recovery leaves bits set in the bitmap. This normally isn't a problem as the offending device will be rejected because of errors. However if device re-adding is being used with non-persistent bitmaps, this can be a problem. Signed-off-by:
-
Michael Hanselmann authored
This patch removes the old radeon driver which has been replaced by a newer one. Signed-off-by:
Michael Hanselmann <linux-kernel@hansmi.ch> Acked-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Antonino Daplas <adaplas@pol.net> Signed-off-by:
-
Antonino A. Daplas authored
The monochrome->color expansion routine that handles bitmaps which have (widths % 8) != 0 (slow_imageblit) produces corrupt characters in big-endian. This is caused by a bogus bit test in slow_imageblit(). Fix. This patch may deserve to go to the stable tree. The code has already been well tested in little-endian machines. It's only in big-endian where there is uncertainty and Herbert confirmed that this is the correct way to go. It should not introduce regressions. Signed-off-by:
Herbert Poetzl <herbert@13thfloor.at> Cc: <stable@kernel.org> Signed-off-by:
-
Richard Purdie authored
Fixes for the pxafb driver: * Return -EINVAL for resolutions that are too large as per framebuffer driver policy. * Increase the error timeout for disabling the LCD controller. The current timeout is sometimes too short on the Sharp Zaurus Cxx00 hardware and an extra delay in an error path shouldn't pose any problems. * Fix a dev reference which causes a compile error when DEBUG is defined. Signed-off-by:
-
