Merge tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.17

Third set of patches for v5.17, and the final one if all goes well. We
have Specific Absorption Rate (SAR) support for both mt76 and rtw88.
Also iwlwifi should be now W=1 warning free. But otherwise nothing
really special this time, business as usual.

Major changes:

mt76
 * Specific Absorption Rate (SAR) support
 * mt7921: new PCI ids
 * mt7921: 160 MHz channel support

iwlwifi
 * fix W=1 and sparse warnings
 * BNJ hardware support
 * add new killer device ids
 * support for Time-Aware-SAR (TAS) from the BIOS
 * Optimized Connectivity Experience (OCE) scan support

rtw88
 * hardware scan
 * Specific Absorption Rate (SAR) support

ath11k
 * qca6390/wcn6855: report signal and tx bitrate
 * qca6390: rfkill support
 * qca6390/wcn6855: regdb.bin support

ath5k
 * switch to rate table based lookup

wilc1000
 * spi: reset/enable GPIO support

* tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (148 commits)
  mt76: mt7921: fix a possible race enabling/disabling runtime-pm
  wilc1000: Document enable-gpios and reset-gpios properties
  wilc1000: Add reset/enable GPIO support to SPI driver
  wilc1000: Convert static "chipid" variable to device-local variable
  rtw89: 8852a: correct bit definition of dfs_en
  rtw88: don't consider deep PS mode when transmitting packet
  ath11k: Fix unexpected return buffer manager error for QCA6390
  ath11k: add support of firmware logging for WCN6855
  ath11k: Fix napi related hang
  ath10k: replace strlcpy with strscpy
  rtw88: support SAR via kernel common API
  rtw88: 8822c: add ieee80211_ops::hw_scan
  iwlwifi: mei: wait before mapping the shared area
  iwlwifi: mei: clear the ownership when the driver goes down
  iwlwifi: yoyo: fix issue with new DBGI_SRAM region read.
  iwlwifi: fw: fix some scan kernel-doc
  iwlwifi: pcie: make sure prph_info is set when treating wakeup IRQ
  iwlwifi: mvm: remove card state notification code
  iwlwifi: mvm: drop too short packets silently
  iwlwifi: mvm: fix AUX ROC removal
  ...
====================

Link: https://lore.kernel.org/r/20211223141108.78808C36AE9@smtp.kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Amit Cohen says:

====================
mlxsw: Add tests for VxLAN with IPv6 underlay

mlxsw driver lately added support for VxLAN with IPv6 underlay.
This set adds tests for IPv6, which are dedicated for mlxsw.

Patch set overview:
Patches #1-#2 make vxlan.sh test more flexible and extend it for IPv6
Patches #3-#4 make vxlan_fdb_veto.sh test more flexible and extend it
for IPv6
Patches #5-#6 add tests for VxLAN flooding for different ASICs
Patches #7-#8 add test for VxLAN related traps and align the existing
test
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the case that sends packets with "too short inner packet" to
include part of ethernet header, to make the trap to be triggered due to
the correct reason.

According to ASIC arch, the trap is triggered if overlay packet length is
less than 18B, and the minimum inner packet should include source MAC and
destination MAC.

Till now the case passed because one of the reserved bits in VxLAN
header was used. This issue was found while adding an equivalent test
for IPv6.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The test configures VxLAN with IPv6 underlay and verifies that the
expected traps are triggered under the right conditions.

The test is similar to the existing IPv4 test.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The device stores flood records in a singly linked list where each
record stores up to X IP addresses of remote VTEPs.

The number of records is changed according to ASIC type and address
family.

Add a test which is similar to the existing IPv4 test to check IPv6.
The test is dedicated for Spectrum-2 and above, which support up to four
IPv6 addresses in one record.

The test verifies that packets are correctly flooded in various cases such
as deletion of a record in the middle of the list.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The device stores flood records in a singly linked list where each
record stores up to X IP addresses of remote VTEPs.

The number of records is changed according to ASIC type and address
family.

Add a test which is similar to the existing IPv4 test to check IPv6.
The test is dedicated for Spectrum-1 switches, which support up to five
IPv6 addresses in one record.

The test verifies that packets are correctly flooded in various cases such
as deletion of a record in the middle of the list.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add test to verify FDB vetos of VxLAN with IPv6 underlay.
Use the existing test which checks IPv4.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxlan_fdb_veto.sh cases are dedicated to test VxLAN with IPv4 underlay.
The main changes to test IPv6 underlay are IP addresses and some flags.

Add variables to define all the values which supposed to be different
for IPv6 testing, set them to use the existing values by default.

The next patch will define the new added variables in a separated file,
so the same tests can be used for IPv6 also.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add test to verify configuration of VxLAN with IPv6 underlay.
Use the existing test which checks IPv4.

Add separated test cases for learning which is not supported for IPv6
and for UDP checksum flags which are different from IPv4 flags.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxlan.sh cases are dedicated to test VxLAN with IPv4 underlay.
The main changes to test IPv6 underlay are IP addresses and some flags.

Add variables to define all the values which supposed to be different
for IPv6 testing, set them to use the existing values by default.

The next patch will define the new added variables in a separated file,
so the same tests can be used for IPv6 also.

Rename some functions to include "ipv4", so the next patch will add
equivalent functions for IPv6.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When kernel.h is used in the headers it adds a lot into dependency hell,
especially when there are circular dependencies are involved.

Replace kernel.h inclusion with the list of what is really being used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds basic support for EtherType RX frame steering for
LLDP and PTP using the hardware offload capabilities.

Example steps for setting up RX frame steering for LLDP and PTP:
$ IFDEVNAME=eth0
$ tc qdisc add dev $IFDEVNAME ingress
$ tc qdisc add dev $IFDEVNAME root mqprio num_tc 8 \
     map 0 1 2 3 4 5 6 7 0 0 0 0 0 0 0 0 \
     queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0

For LLDP
$ tc filter add dev $IFDEVNAME parent ffff: protocol 0x88cc \
     flower hw_tc 5
OR
$ tc filter add dev $IFDEVNAME parent ffff: protocol LLDP \
     flower hw_tc 5

For PTP
$ tc filter add dev $IFDEVNAME parent ffff: protocol 0x88f7 \
     flower hw_tc 6

Show tc ingress filter
$ tc filter show dev $IFDEVNAME ingress

v1->v2:
 Thanks to Kurt's and Sebastian's suggestion.
 - change from __be16 to u16 etype
 - change ETHER_TYPE_FULL_MASK to use cpu_to_be16() macro
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch series extends the current supported bridge flags with the
following flags: BR_FLOOD, BR_BCAST_FLOOD and BR_LEARNING.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix suspicious rcu_dereference_protected() usage when offloading tc action.

We should hold tcfa_lock to offload tc action in action initiation.

Without these changes, the following warning will be observed:

WARNING: suspicious RCU usage
5.16.0-rc5-net-next-01504-g7d1f236dcffa-dirty #50 Tainted: G          I
-----------------------------
include/net/tc_act/tc_tunnel_key.h:33 suspicious rcu_dereference_protected() usage!
1 lock held by tc/12108:
CPU: 4 PID: 12108 Comm: tc Tainted: G
Hardware name: Dell Inc. PowerEdge R740/07WCGN, BIOS 1.6.11 11/20/2018
Call Trace:
<TASK>
dump_stack_lvl+0x49/0x5e
dump_stack+0x10/0x12
lockdep_rcu_suspicious+0xed/0xf8
tcf_tunnel_key_offload_act_setup+0x1de/0x300 [act_tunnel_key]
tcf_action_offload_add_ex+0xc0/0x1f0
tcf_action_init+0x26a/0x2f0
tcf_action_add+0xa9/0x1f0
tc_ctl_action+0xfb/0x170
rtnetlink_rcv_msg+0x169/0x510
? sched_clock+0x9/0x10
? rtnl_newlink+0x70/0x70
netlink_rcv_skb+0x55/0x100
rtnetlink_rcv+0x15/0x20
netlink_unicast+0x1a8/0x270
netlink_sendmsg+0x245/0x490
sock_sendmsg+0x65/0x70
____sys_sendmsg+0x219/0x260
? __import_iovec+0x2c/0x150
___sys_sendmsg+0xb7/0x100
? __lock_acquire+0x3d5/0x1f40
? __this_cpu_preempt_check+0x13/0x20
? lock_is_held_type+0xe4/0x140
? sched_clock+0x9/0x10
? ktime_get_coarse_real_ts64+0xbe/0xd0
? __this_cpu_preempt_check+0x13/0x20
? lockdep_hardirqs_on+0x7e/0x100
? ktime_get_coarse_real_ts64+0xbe/0xd0
? trace_hardirqs_on+0x2a/0xf0
__sys_sendmsg+0x5a/0xa0
? syscall_trace_enter.constprop.0+0x1dd/0x220
__x64_sys_sendmsg+0x1f/0x30
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f4db7bb7a60

Fixes: 8cbfe939 ("flow_offload: allow user to offload tc action to net device")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Struct sctp_ep_common is included in both asoc and ep, but hlist_node
and hashent are only needed by ep after asoc_hashtable was dropped by
Commit b5eff712 ("sctp: drop the old assoc hashtable of sctp").

So it is better to move hlist_node and hashent from sctp_ep_common to
sctp_endpoint, and it saves some space for each asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Amit Cohen says:

====================
Add tests for VxLAN with IPv6 underlay

mlxsw driver lately added support for VxLAN with IPv6 underlay.
This set adds the relevant tests for IPv6, most of them are same to
IPv4 tests with the required changes.

Patch set overview:
Patch #1 relaxes requirements for offloading TC filters that
match on 802.1q fields. The following selftests make use of these
newly-relaxed filters.
Patch #2 adds preparation as part of selftests API, which will be used
later.
Patches #3-#4 add tests for VxLAN with bridge aware and unaware.
Patche #5 cleans unused function.
Patches #6-#7 add tests for VxLAN symmetric and asymmetric.
Patch #8 adds test for Q-in-VNI.
====================

Link: https://lore.kernel.org/r/20211221144949.2527545-1-amcohen@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add test to check Q-in-VNI traffic with IPv6 underlay and overlay.
The test is similar to the existing IPv4 test.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a similar fashion to the asymmetric test, add a test for symmetric
routing. In symmetric routing both the ingress and egress VTEPs perform
routing in the overlay network into / from the VxLAN tunnel. Packets in
different directions use the same VNI - the L3 VNI.
Different tenants (VRFs) use different L3 VNIs.

Add a test which is similar to the existing IPv4 test to check IPv6.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In asymmetric routing the ingress VTEP routes the packet into the
correct VxLAN tunnel, whereas the egress VTEP only bridges the packet to
the correct host. Therefore, packets in different directions use
different VNIs - the target VNI.

Add a test which is similar to the existing IPv4 test to check IPv6.

The test uses a simple topology with two VTEPs and two VNIs and verifies
that ping passes between hosts (local / remote) in the same VLAN (VNI)
and in different VLANs belonging to the same tenant (VRF).

While the test does not check VM mobility, it does configure an anycast
gateway using a macvlan device on both VTEPs.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Remove `vxlan_ping_test()` which is not used and probably was copied
mistakenly from vxlan_bridge_1d.sh.

This was found while adding an equivalent test for IPv6.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The tests are very similar to their VLAN-unaware counterpart
(vxlan_bridge_1d_ipv6.sh and vxlan_bridge_1d_port_8472_ipv6.sh),
but instead of using multiple VLAN-unaware bridges, a single VLAN-aware
bridge is used with multiple VLANs.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add tests similar to vxlan_bridge_1d.sh and vxlan_bridge_1d_port_8472.sh.

The tests set up a topology with three VxLAN endpoints: one
"local", possibly offloaded, and two "remote", formed using veth pairs
and likely purely software bridges. The "local" endpoint is connected to
host systems by a VLAN-unaware bridge.

Since VxLAN tunnels must be unique per namespace, each of the "remote"
endpoints is in its own namespace. H3 forms the bridge between the three
domains.

Send IPv4 packets and IPv6 packets with IPv6 underlay.
Use `TC_FLAG`, which is defined in `forwarding.config` file, for TC
checks. `TC_FLAG` allows testing that on HW datapath, the traffic
actually goes through HW.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently `ping_do()` and `ping6_do()` send 10 packets.

There are cases that it is not possible to catch only the interesting
packets using tc rule, so then, it is possible to send many packets and
verify that at least this amount of packets hit the rule.

Add `PING_COUNT` variable, which is set to 10 by default, to allow tests
sending more than 10 packets using the existing ping API.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Spectrum ASICs do not support matching of VLAN ID at egress.
Currently, mlxsw driver forbids matching of all VLAN related fields at
egress, which is too strict check.

For example, the following filter is not supported by the driver:
$ tc filter add dev swpX egress protocol 802.1q pref 1 handle 101 flower
vlan_ethtype ipv4 src_ip .. dst_ip .. skip_sw action pass
Error: mlxsw_spectrum: vlan_id key is not supported on egress.
We have an error talking to the kernel

The filter above does not match on VLAN ID, but is bounced anyway.

Make the check more specific, forbid only matching of 'vlan_id' at egress.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Saeed Mahameed says:

====================
mlx5-updates-2021-12-21

1) From Shay Drory: Devlink user knobs to control device's EQ size

This series provides knobs which will enable users to
minimize memory consumption of mlx5 Functions (PF/VF/SF).
mlx5 exposes two new generic devlink params for EQ size
configuration and uses devlink generic param max_macs.

LINK: https://lore.kernel.org/netdev/20211208141722.13646-1-shayd@nvidia.com/

2) From Tariq and Lama, allocate software channel objects and statistics
  of a mlx5 netdevice private data dynamically upon first demand to save on
  memory.

* tag 'mlx5-updates-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
  net/mlx5e: Take packet_merge params directly from the RX res struct
  net/mlx5e: Allocate per-channel stats dynamically at first usage
  net/mlx5e: Use dynamic per-channel allocations in stats
  net/mlx5e: Allow profile-specific limitation on max num of channels
  net/mlx5e: Save memory by using dynamic allocation in netdev priv
  net/mlx5e: Add profile indications for PTP and QOS HTB features
  net/mlx5e: Use bitmap field for profile features
  net/mlx5: Remove the repeated declaration
  net/mlx5: Let user configure max_macs generic param
  devlink: Clarifies max_macs generic devlink param
  net/mlx5: Let user configure event_eq_size param
  devlink: Add new "event_eq_size" generic device param
  net/mlx5: Let user configure io_eq_size param
  devlink: Add new "io_eq_size" generic device param
====================

Link: https://lore.kernel.org/r/20211222031604.14540-1-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Commit d068ca2a ("codel: split into multiple files") moved all
Qdisc-related code to codel_qdisc.h, move the include of pkt_sched.h
as well.

This is similar to the previous commit, although we don't care as
much about incremental builds after pkt_sched.h was touched itself
it is included by net/sch_generic.h which is modified ~20 times
a year.

This decreases the incremental build size after touching pkt_sched.h
from 1592 to 617 objects.

Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-2-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Since sock.h is modified relatively often (60 times in the last
12 months) it seems worthwhile to decrease the incremental build
work.

CoDel's header includes net/inet_ecn.h which in turn includes net/sock.h.
codel.h is itself included by mac80211 which is included by much of
the WiFi stack and drivers. Removing the net/inet_ecn.h include from
CoDel breaks the dependecy between WiFi and sock.h.

Commit d068ca2a ("codel: split into multiple files") moved all
the code which actually needs ECN helpers out to net/codel_impl.h,
the include can be moved there as well.

This decreases the incremental build size after touching sock.h
from 4999 objects to 4051 objects.

Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The variable bytes is being used to summate slot lengths,
however the value is never used afterwards. The summation
is redundant so remove variable bytes.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211222003937.727325-1-colin.i.king@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix an odd indent where some code was left indented, and causes smatch
to warn:
ice_log_pkg_init() warn: inconsistent indenting

While here, for consistency, add a break after the default case.

This commit has a Fixes: but we caught this while it was only in net-next.

Fixes: 247dd97d ("ice: Refactor status flow for DDP load")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20211221230538.2546315-1-jesse.brandeburg@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2021-12-21

This series contains updates to ice driver only.

Karol modifies the reset flow to correct issues with PTP reset.

Jake extends PTP support for E822 based devices. This includes a few
cleanup patches, that fix some minor issues. In addition, there are some
slight refactors to ease the addition of E822 support, followed by adding
the new hardware implementation ice_ptp_hw.c.

There are a few major differences with E822 support compared to E810
support:

*) The E822 device has a Clock Generation Unit which must be initialized in
order to generate proper clock frequencies on the output that drives the PTP
hardware clock registers

*) The E822 PHY is a bit different and requires a more complex
initialization procedure which must be rerun any time the link configuration
changes.

*) The E822 devices support enhanced timestamp calibration by making use of
a process called Vernier offset measurement. This allows the hardware to
measure phase offset related to the PHY clocks for Serdes and FEC, reducing
the inaccuracy of the timestamp relative to the actual packet transmission
and receipt. Making use of this requires data gathered from the first
transmitted and received packets, and waiting for the PHY to complete the
calibration measurements. This is done as part of a new kthread, ov_work.
Note that to avoid delay in enabling timestamps, we start the PHY in
'bypass' mode which allows timestamps to be captured without the Vernier
calibration measurement. Once the first packets have been sent and received,
we then complete the calibration setup and exit bypass mode and begin using
the more precise timestamps. According to the datasheet, timestamps without
calibration data can be incorrect relative to actual receipt or transmission
by up to 1 clock cycle (~1.25 nanoseconds), while calibrated timestamps
should be correct to within 1/8th of a clock cycle (~0.15 nanoseconds).

*) E822 devices support crosstimestamping via PCIe PTM, which we enable when
available on the platform.

There is a fair amount of logic required to perform PHY and CGU
initialization, which is the vast majority of the new code, but it is fairly
self contained within ice_ptp_hw.c, with the exception of monitoring for
offset validity being handled by a kthread.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  ice: support crosstimestamping on E822 devices if supported
  ice: exit bypass mode once hardware finishes timestamp calibration
  ice: ensure the hardware Clock Generation Unit is configured
  ice: implement basic E822 PTP support
  ice: convert clk_freq capability into time_ref
  ice: introduce ice_ptp_init_phc function
  ice: use 'int err' instead of 'int status' in ice_ptp_hw.c
  ice: PTP: move setting of tstamp_config
  ice: introduce ice_base_incval function
  ice: Fix E810 PTP reset flow
====================

Link: https://lore.kernel.org/r/20211221174845.3063640-1-anthony.l.nguyen@intel.comAcked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fix a possible race enabling/disabling runtime-pm between
mt7921_pm_set() and mt7921_poll_rx() since mt7921_pm_wake_work()
always schedules rx-napi callback and it will trigger
mt7921_pm_power_save_work routine putting chip to in low-power state
during mt7921_pm_set processing.
Suggested-by: Deren Wu <deren.wu@mediatek.com>
Tested-by: Deren Wu <deren.wu@mediatek.com>
Fixes: 1d8efc74 ("mt76: mt7921: introduce Runtime PM support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/0f3e075a2033dc05f09dab4059e5be8cbdccc239.1640094847.git.lorenzo@kernel.org

Add documentation for the ENABLE and RESET GPIOs that may be needed by
wilc1000-spi.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221212531.4011609-3-davidm@egauge.net

For the SDIO driver, the RESET/ENABLE pins of WILC1000 are controlled
through the SDIO power sequence driver.  This commit adds analogous
support for the SPI driver.  Specifically, during initialization, the
chip will be ENABLEd and taken out of RESET and during
deinitialization, the chip will be placed back into RESET and disabled
(both to reduce power consumption and to ensure the WiFi radio is
off).

Both RESET and ENABLE GPIOs are optional.  However, if the ENABLE GPIO
is specified, then the RESET GPIO should normally also be specified as
otherwise there is no way to ensure proper timing of the ENABLE/RESET
sequence.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221212531.4011609-2-davidm@egauge.net

Move "chipid" variable into the per-driver structure so the code
doesn't break if more than one wilc1000 module is present.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221210538.4011227-1-davidm@egauge.net

Since there are other protections in the set channel flow, fortunately old
wrong setting won't affect the performance.
Signed-off-by: Chung-Hsuan Hung <hsuan8331@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221024800.23814-1-pkshih@realtek.com

In original flow, driver needs to ensure chip leave deep ps mode
before transmitting any packet, and don't enter deep ps mode beofre
PCIE DMA is finished. Now with the support of 8822ce's hardware
setting and firmware after v9.9.11, these limits are removed.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221020230.20764-1-pkshih@realtek.com

ath.git patches for v5.17. Major changes:

ath11k

* qca6390/wcn6855: report signal and tx bitrate

* qca6390: rfkill support

* qca6390/wcn6855: regdb.bin support

ath5k

* switch to rate table based lookup

We are seeing below error on QCA6390:
...
[70211.671189] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
[70212.696154] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
[70213.092941] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
...

The reason is that, with commit 734223d7 ("ath11k: change return
buffer manager for QCA6390"), ath11k expects the return buffer manager
(RBM) field of descriptor configured as HAL_RX_BUF_RBM_SW1_BM when
parsing error frames from WBM2SW3_RELEASE ring. This is a wrong change
cause the RBM field is set as HAL_RX_BUF_RBM_SW3_BM.

The same issue also applies to REO2TCL ring though we have not got any
error reported.

Fix it by changing RBM from HAL_RX_BUF_RBM_SW1_BM to HAL_RX_BUF_RBM_SW3_BM
for these two rings.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Fixes: 734223d7 ("ath11k: change return buffer manager for QCA6390")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211222013536.582527-1-quic_bqiang@quicinc.com

Host enables WMI firmware logging feature via QMI message.
Host receives firmware logging messages on WMI_DIAG_EVENTID, then
sends logging messages to user space via event tracing infrastructure.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Cheng Wang <quic_chengwan@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211220121053.357087-1-quic_chengwan@quicinc.com

Similar to the same bug in ath10k, a napi disable w/out it being enabled
will hang forever.  I believe I saw this while trying rmmod after driver
had some failure on startup.  Fix it by keeping state on whether napi is
enabled or not.

And, remove un-used napi pointer in ath11k driver base struct.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20200903195254.29379-1-greearb@candelatech.com