Note that we do not generate the redirect netevent any longer,
because we don't create a new cached route.

Instead, once the new neighbour is bound to the cached route,
we emit a neigh update event instead.
Signed-off-by: David S. Miller <davem@davemloft.net>

The general idea is that if we learn new PMTU information, we
bump the peer genid.

This triggers the dst_ops->check() code to validate and if
necessary propagate the new PMTU value into the metrics.

Learned PMTU information self-expires.

This means that it is not necessary to kill a cached route
entry just because the PMTU information is too old.

As a consequence:

1) When the path appears unreachable (dst_ops->link_failure
   or dst_ops->negative_advice) we unwind the PMTU state if
   it is out of date, instead of killing the cached route.

   A redirected route will still be invalidated in these
   situations.

2) rt_check_expire(), rt_worker_func(), et al. are no longer
   necessary at all.
Signed-off-by: David S. Miller <davem@davemloft.net>

Platform code can now set the MICREL_PHY_50MHZ_CLK bit of dev_flags in a fixup
routine (registered with phy_register_fixup_for_uid()), to make the KZS8051RNL
PHY work with 50MHz RMII reference clock.

Cc: David J. Choi <david.choi@micrel.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

With previous patch, rose_get_neigh() routine
investigates the full list of neighbor nodes
until it finds or not an already connected node whether
it is called locally or through a level 3 transit frame.
If no routes are opened through an adjacent connected node
then a classical connect request is attempted.

Then there is no more reason for an extra loop such
as the one removed by this patch.
Signed-off-by: Bernard Pidoux <f6bvp@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

FPAC AX25 packet application is using Linux kernel ROSE
routing skills in order to connect or send packets to remote stations
knowing their ROSE address via a network of interconnected nodes.

Each FPAC node has a ROSE routing table that Linux ROSE module is
looking at each time a ROSE frame is relayed by the node or when
a connect request to a neighbor node is received.

A previous patch improved the system time response by looking at
already established routes each time the system was looking for a
route to relay a frame. If a neighbor node routing the destination
address was already connected, then the frame would be sent
through him. If not, a connection request would be issued.

The present patch extends the same routing capability to a connect
request asked by a user locally connected into an FPAC node.
Without this patch, a connect request was not well handled unless it
was directed to an immediate connected neighbor of the local node.

Implemented at a number of ROSE FPAC node stations, the present patch
improved dramatically FPAC ROSE routing time response and efficiency.
Signed-off-by: Bernard Pidoux <f6bvp@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0c838ff1 (ipv4: Consolidate all default route selection
implementations.) forgot to remove one rcu_read_unlock() from
fib_select_default().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bosch C_CAN controller is a full-CAN implementation which is compliant
to CAN protocol version 2.0 part A and B. Bosch C_CAN user manual can be
obtained from:

http://www.semiconductors.bosch.de/media/en/pdf/ipmodules_1/c_can/users_manual_c_can.pdf

This patch adds the support for this controller.
The following are the design choices made while writing the controller
driver:
1. Interface Register set IF1 has be used only in the current design.
2. Out of the 32 Message objects available, 16 are kept aside for RX
   purposes and the rest for TX purposes.
3. NAPI implementation is such that both the TX and RX paths function
   in polling mode.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some JMicron Chip treat 0 as error checksum for UDP packets.
Which should be "No checksum needed".
Reported-by: Adam Swift <Adam.Swift@omnitude.net>
Confirmed-by: "Aries Lee" <arieslee@jmicron.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The value of the register which holds receive Unicast MAC Address
sometimes get messed-up after resume.
This patch refill it before enabling the hardware filter.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding control to clk_rx, and makes the control of clk_{rx|tx|tcp}
with safer sequence.
This sequence is provided by JMicron.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clear Transmit Timer/Retry setting while full-duplex.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

After main chip rev 5, the hardware support more power saving
control registers.
Some Non-Linux drivers might turn off the phy power with new
interfaces, this patch makes it possible for Linux to turn it
on again.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Get the main and sub chip revision for later workaround use.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

add possibility to addif/delif via rtnetlink
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

allow enslaving/releasing using netlink interface
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch allows userspace to enslave/release slave devices via netlink
interface using IFLA_MASTER. This introduces generic way to add/remove
underling devices.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix two bugs introduced by the commit
c659c38b ("tlan: Code cleanup:
checkpatch.pl is relatively happy now.") In that change,
TLAN_CSTAT_READY was considered as a bit mask containing a single bit
set while it was actually had two set instead.

Many thanks to Dan Carpenter for finding the mistake.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev->master is now tightly connected to bonding driver. This patch makes
this pointer more general and ready to be used by others.

 - netdev_set_master() - bond specifics moved to new function
   netdev_set_bond_master()
 - introduced netif_is_bond_slave() to check if device is a bonding slave
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No need to check (master) twice and to drive in and out the header file.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unneeded depends on PHYLIB.  The config selection is already in
an if PHYLIB / endif block.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows user-space to send a '1500' MTU VLAN packet on a
1500 MTU ethernet frame.  The extra 4 bytes of a VLAN header is
not usually charged against the MTU when other parts of the
network stack is transmitting vlans...
Signed-off-by: Ben Greear <greearb@candelatech.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

WOL is not supported for Vrtual Functions.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid accessing the hardware when UE is detected.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

> call pci msix disable in be_suspend
	> call pci msix enable in be_resume
	> stop worker thread in be_suspend
	> start worker thread in be_resume
	> stop worker thread in be_shutdown
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be_cmd_pmac_add/del functions need to pass domain number to the firmware.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we are always using the Emulex OUI for a VF MAC address
while generating MAC for a VF.  Use OUI from current MAC instead.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PF needs to cleanup all the interface handles that it created for the VFs.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to avoid the completion processing for be_vf_eth_addr_config
to consume the link status notification before netdev_register.
Otherwise this causes the PF miss its first link status update.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While configuring QOS for VFs, the VF number should be translated
to domain number correctly.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>