Fix checkpatch warning:
WARNING: kfree(NULL) is safe this check is probably not required

Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch fixes a couple of issues:
- absence of deallocation of rsi_dev->rx_usb_urb[0] in the driver;
- potential NULL pointer dereference because of lack of checks for memory
  allocation success in rsi_init_usb_interface().

By the way, it makes rsi_probe() returning error code instead of 1
and fixes comments regarding returning values.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Right now sleep duration is configured as beacon interval. It should be
the multiple of beacon interval by listen period which helps to
reduce station power consumption.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Earlier the listen interval is used to decide switching between
operating and off-channels during bgscan and to improve throughput,
the listen interval is reduced to 1. After optimiztion in scan
state machine, listen period is not used for decision making and
hence reverting it back to original value.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The beacon configurations are not cached properly after the station
associates with AP. Not handling BEACON_INFO, is failing to update
dtim period and also it is causing below warning message.

WARNING: CPU: 1 PID: 0 at drivers/net/wireless/ath/ath9k/recv.c:548
ath_rx_tasklet+0xc89/0xca0 [ath9k]()
 Call Trace:
  [<c14669c9>] dump_stack+0x48/0x69
  [<c104f1a2>] warn_slowpath_common+0x82/0xa0
  [<fd38c2f9>] ? ath_rx_tasklet+0xc89/0xca0 [ath9k]
  [<fd38c2f9>] ? ath_rx_tasklet+0xc89/0xca0 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Treat frames that underwent a CCK or OFDM restart as frames with an invalid CRC.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When the FIF_FCSFAIL filter flag is set, pass frames with CRC errors.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Why is converting time formats so desired if there are proper
interfaces for this?
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bing Zhao <bzhao@marvell.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reverts commit a82fc3b4a2bceb7c6587249cb690342eb5065979.

Thomas corrected me on that I misunderstood Johannes' comment
for net_timedelta() and the ktime_get_real() usage inside
__net_timestamp().

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

CC: "Rafał Miłecki" <zajec5@gmail.com>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fixed a warning related to incorrect return type and removed an
unnecessary semi colon.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fixed a potential buffer overflow in 'rsi_rates' and a sparse warning
related to difference in endianness in rsi_91x_mgmt.c.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The p54 driver uses request_firmware() twice, once for actual
firmware and then another time for an optional user overide on
EEPROM, 3826.eeprom. The custom EEPROM  is optional but if not
present we'll introduce an extra lag of 60 seconds with udev
present. Annotate we don't want udev nonsense here to avoid
the lag in case its not present.

This was found with the following SmPL patch.

@ firmware_not_critical @
expression cf;
expression config_file;
expression dev;
int ret;
identifier l;
statement S;
@@

-	ret = request_firmware(&cf, config_file, dev);
+	ret = request_firmware_direct(&cf, config_file, dev);
	if (ret < 0) {
		... when != goto l;
		    when != return ret;
		    when any
	} else {
		...
		release_firmware(cf);
		...
	}

Cc: Takashi Iwai <tiwai@suse.de>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: linux-wireless@vger.kernel.org
Cc: cocci@systeme.lip6.fr
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Acked-By: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix tx gain table index on fast channel change for AR953x.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Clean ucode selection, fix choice of firmware for LCN, drop some goto-s,
add new devices.
Tested on 14e4:4312, 14e4:4315, 14e4:4328, 14e4:432b, 14e4:4353.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For consistency with other drivers, replace a magic number by a macro.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For consistency with other drivers, replace a magic number by a macro.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bt_msr & 0xfc will never match 0x3. Fix this by using a mask that actually matches the available types.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bt_msr & 0xfc will never match 0x3. Fix this by using a mask that actually matches the available types.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bt_msr & 0xfc will never match 0x3. Fix this by using a mask that actually matches the available types.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add support for external PA and clean code a bit.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The users of the fwil put an error message in the log so there is
no need to do the same in the lower level functions in fwil when
the firmware on the device returns an error. Some errors can be
ignored for the driver to function and this will avoid driver users
to point at the low-level error message as potential bug.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of controlling mpc setting during scan operation, initialize
mpc setting and then let firmware take care of it.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
[arend@broadcom.com: keep mpc setting for bcm4329]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

All log messages were set to TRACE level, which is intended
for function entry and exit. Using INFO instead in other
places. Also reducing an error message that always popped
up upon module unload.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Passing a pointer from user space and using it directly in driver is not a
preferable behavior. Switch to cfg80211 vendor mode for dongle command for
better cross platform compatibility.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some of the USB devices also have Bluetooth inside. These devices
can with specific firmware result in a composite USB device. This
change will update the driver such that it will also accept the
correct interface of composite devices. It is backward compatible
with old non-composite USB fw.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After updating 2G bandwidth capability clear ht info. This will be properly
set upon calling brcmf_update_wiphy_bands().
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add the USB 43566 device to the supported devices list. The 43566
is a WiFi-only variant of the 43569. It uses the same FW as 43569.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Added usb device id for the new device 43569 to the list of
supported devices.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Applying ++ to a bool is equivalent to setting it true, regardless of
its initial value (bools are not uint1_t). Hence the function
wl_get_vif_state_all can only ever return true/false. The only in-tree
caller uses its return value as a boolean. So update its return type,
and since the list traversal and bit testing have no side effects,
just return true immediately. Its return value tells if any vif is in
the specified state, so also rename it to brcmf_get_vif_state_any.

Reviewed-by: Arend van Spriel<arend@broadcom.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Sleep Confirm command is sent separately while other commands
are handled through cmd_pending_q. Print sleep_confirm cmd and
its response as well as power save events so that we have a
clearer picture of power save handshake in driver log.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch updates mwifiex Copyright to 2014.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some SDIO controllers do not support MMC_PM_KEEP_POWER properly.
To test host sleep feature without putting the system into sleep
we need to simulate host sleep configuration & handshake between
driver and firmware using customized parameters.
This patch adds hscfg debugfs item, with which user could change
host sleep parameters for debugging.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Firmware dump feature is added for SDIO based chipsets
which can be used with the help of ethtool commands.

1) Trigger firmware dump operation:
ethtool --set-dump mlan0 0xff

When the operation is completed, udev event will be sent to
trigger external application.

2) Following udev rule can be used to get the data from ethtool:
DRIVER=="mwifiex_sdio", ACTION=="change", RUN+="/sbin/mwifiex_sdio_fw_dump.sh"

mwifiex_sdio_fw_dump.sh: #!/bin/bash
ethtool --set-dump mlan0 0
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/ITCM.log

ethtool --set-dump mlan0 1
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/DTCM.log

ethtool --set-dump mlan0 2
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/SQRAM.log

ethtool --set-dump mlan0 3
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/APU.log

ethtool --set-dump mlan0 4
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/CIU.log

ethtool --set-dump mlan0 5
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/ICU.log

ethtool --set-dump mlan0 6
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/MAC.log
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>