Similar to commit 8f42cb7f ("ARM: dts: omap4: Add l4 interconnect
hierarchy and ti-sysc data"), let's add proper interconnect hierarchy
for l4 interconnect instances with the related ti-sysc interconnect
module data as in Documentation/devicetree/bindings/bus/ti-sysc.txt.

Using ti-sysc driver binding allows us to start dropping legacy platform
data in arch/arm/mach-omap2/omap*hwmod*data.c files later on in favor of
ti-sysc dts data.

This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.

Note that we cannot yet include this file from the SoC dtsi file until
the child devices are moved to their proper locations in the
interconnect hierarchy in the following patch. Otherwise we would have
the each module probed twice.

Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to
their proper location and enable probing using ti-sysc.

In general the first child device address range starts at range 0
from the ti-sysc interconnect target so the move involves adjusting
the child device reg properties for that.

In case of any regressions, problem devices can be reverted to probe
with legacy platform data as needed by moving them back and removing
the related interconnect target module node.

Note that we are not yet moving dss or wkup_m3, those will be moved
later after some related driver changes.

Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Similar to commit 8f42cb7f ("ARM: dts: omap4: Add l4 interconnect
hierarchy and ti-sysc data"), let's add proper interconnect hierarchy
for l4 interconnect instances with the related ti-sysc interconnect
module data as in Documentation/devicetree/bindings/bus/ti-sysc.txt.

Using ti-sysc driver binding allows us to start dropping legacy platform
data in arch/arm/mach-omap2/omap*hwmod*data.c files later on in favor of
ti-sysc dts data.

This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.

Note that we cannot yet include this file from the SoC dtsi file until
the child devices are moved to their proper locations in the
interconnect hierarchy in the following patch. Otherwise we would have
the each module probed twice.

Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Convert DRA7xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM isntance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Convert AM43xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM isntance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Convert AM33xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM instance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

TI sysc driver changes for v4.20 merge window

This series gets rid of the SYSC_QUIRK_RESOURCE_PROVIDER to make device
detection happen mostly only if #define DEBUG is set. Few core devices still
need to be detected to set legacy quirks.

We also add support for booting am335x, am437x and dra7 SoCs with L4 devices
defined in device tree instead of legacy platform data.

And finally we simplify suspend with just SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
and dropping the custom functions that were attempting to work around
issues that really turned out to be child device driver related issues.

Apologies for a late pull request, debugging the suspend issues took a while
and I did not want to send these changes until that got sorted out.

SoCs like AM43XX lose clock registers context during RTC-only
suspend. Hence add functions to save/restore the clock registers
context.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

The clock gate restore context function enables or disables
the gate clocks based on the enable_count. This is done in cases
where the clock context is lost and based on the enable_count
the clock either needs to be enabled/disabled.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Deep enough power saving mode can result into losing context of the clock
registers also, and they need to be restored once coming back from the power
saving mode. Hence add functions to save/restore clock context.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

The new clkctrl data layout for dra7xx is split based on clockdomain
boundaries. Previously the split was based on CM boundaries. This patch
adds the new data as separate data entity, retaining the compatibility
data also for now. The compatibility data can be removed once no longer
needed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>

Rename the existing clkctrl data in preparation of upcoming clkdm
based split for it. Once the DT data has transitioned also, the
compat data can be removed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>

The new clkctrl data layout for am43xx is split based on clockdomain
boundaries. Previously the split was based on CM boundaries. This patch
adds the new data as separate data entity, retaining the compatibility
data also for now. The compatibility data can be removed once no longer
needed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>

Rename the existing clkctrl data in preparation of upcoming clkdm
based split for it. Once the DT data has transitioned also, the
compat data can be removed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>

The new clkctrl data layout for am33xx is split based on clockdomain
boundaries. Previously the split was based on CM boundaries. This patch
adds the new data as separate data entity, retaining the compatibility
data also for now. The compatibility data can be removed once no longer
needed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>

Rename the existing clkctrl data in preparation of upcoming clkdm
based split for it. Once the DT data has transitioned also, the
compat data can be removed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>

The change in the DTS data node naming prevents using underscore
within the node names and force usage of dash instead. On the other
hand, clockdomains use underscore instead of dash, so this must be
replaced within the driver code so that the mapping between the two
can be done properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>

Currently, only one clkctrl node can be added under a specific CM node
due to limitation with the implementation. Modify the code to pick-up
clockdomain name from the clkctrl node instead of CM node if provided.
Also, add a new flag to the TI clock driver so that both modes can
be supported simultaneously.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>

The new data layout will be split based on clockdomain boundaries, instead
of CM boundaries. This introduces a few new clkctrl providers, that have
different indices for the clkctrl data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>

The new data layout will be split based on clockdomain boundaries, instead
of CM boundaries. This introduces a few new clkctrl providers, that have
different indices for the clkctrl data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>

The new data layout will be split based on clockdomain boundaries, instead
of CM boundaries. This introduces a few new clkctrl providers, that have
different indices for the clkctrl data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>

As Grygorii Strashko pointed out, the runtime PM use count of the
children can be whatever at suspend and we should not use it. So
let's just suspend ti-sysc at noirq level and get rid of some code.

Let's also remove the PM_SLEEP ifdef and use __maybe_unused as the
PM code already deals with the ifdefs.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We're currently warning about busy children on suspend in
sysc_child_suspend_noirq() but the legacy code omap_device does
not do that. Let's just make it dev_dbg() instead of dev_warn().
Signed-off-by: Tony Lindgren <tony@atomide.com>

We want to see the names of detected devices when DEBUG is enabled.
Signed-off-by: Tony Lindgren <tony@atomide.com>

We need to detect timer and gpio on dra7 because of the
SYSC_QUIRK_LEGACY_IDLE flag for suspend and resume.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Looks like we still have two instances of phy_handle that did not
get update by Grygorii's series. Let's replace these too with
standard phy-handle.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Neeraj Dantu <dantuguf14105@gmail.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add support for Moxa UC-2101 open platform

The UC-2101 computing platform is designed for industrial embedded
data acquisition and processing applications.

The features of UC-2101 are:
* eMMC
* SPI flash
* 1x LAN
* 1x RS-232/422/485 ports, software-selectable
* EEPROM
* TPM 2.0
* Watchdog
* RTC
* User gpio-keys
* User LEDs
* User button
Signed-off-by: Wes Huang (黃淵河) <wes.huang@moxa.com>
Signed-off-by: Fero JD Zhou (周俊達) <FeroJD.Zhou@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The UC-2100 series consists many boards with different peripheral
devices and wireless modules, hence we fetch common items and
create a common dtsi file to increase reusability. All boards in
UC-2100 series will include this common dtsi file.
Signed-off-by: Wes Huang (黃淵河) <wes.huang@moxa.com>
Signed-off-by: Fero JD Zhou (周俊達) <FeroJD.Zhou@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Since SMPS10 and OTG cable detection extcon are described here, and
work to enable OTG power when an OTG cable is plugged in, we can
define OTG mode in the controller (which is disabled by default in
omap5.dtsi).

Tested on OMAP5EVM and Pyra.
Suggested-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add ti,syscon-unaligned-access property to PCIe RC nodes to set
appropriate bits in CTRL_CORE_SMA_SW_7 register to enable workaround for
errata i870.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Bit positions of PCIE_SS1_AXI2OCP_LEGACY_MODE_ENABLE and
PCIE_SS1_AXI2OCP_LEGACY_MODE_ENABLE in CTRL_CORE_SMA_SW_7 are
incorrectly documented in the TRM. In fact, the bit positions are
swapped. Update the DT bindings for PCIe EP to reflect the same.

Fixes: d23f3839 ("ARM: dts: DRA7: Add pcie1 dt node for EP mode")
Cc: stable@vger.kernel.org
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We have defined a new DTS and it should be compiled.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pullup and down settings were missing, so add them to avoid
floating pins and make headset detection working.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add CEC support to the tda998x.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The full AM3517-EVM shipped with an add-on board which contained
two Audio codecs, a GPIO expander with a variety of buttons, and
some other features.  This patch enables these portions of the UI
board because they don't directly conflict with existing features.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This enables the possibility to have more aggressive runtime pm
by providing proper wakeup irq for the serial console.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>