- 13 Nov, 2018 7 commits
-
-
Rafael J. Wysocki authored
commit da5e79bc upstream. If the policy limits change between invocations of cs_dbs_update(), the requested frequency value stored in dbs_info may not be updated and the function may use a stale value of it next time. Moreover, if idle periods are takem into account by cs_dbs_update(), the requested frequency value stored in dbs_info may be below the min policy limit, which is incorrect. To fix these problems, always update the requested frequency value in dbs_info along with the local copy of it when the previous requested frequency is beyond the policy limits and avoid decreasing the requested frequency below the min policy limit when taking idle periods into account. Fixes: abb66279 (cpufreq: conservative: Fix next frequency selection) Fixes: 00bfe058 (cpufreq: conservative: Decrease frequency faster for deferred updates) Reported-by:
Waldemar Rymarkiewicz <waldemarx.rymarkiewicz@intel.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Hou Tao authored
commit 92e2921f upstream. When an invalid mount option is passed to jffs2, jffs2_parse_options() will fail and jffs2_sb_info will be freed, but then jffs2_sb_info will be used (use-after-free) and freeed (double-free) in jffs2_kill_sb(). Fix it by removing the buggy invocation of kfree() when getting invalid mount options. Fixes: 92abc475 ("jffs2: implement mount option parsing and compression overriding") Cc: stable@kernel.org Signed-off-by:
Hou Tao <houtao1@huawei.com> Reviewed-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by:
-
Dmitry Bazhenov authored
commit e7c6a556 upstream. Devices with compatible="pmbus" field have zero initial page count, and pmbus_clear_faults() being called before the page count auto- detection does not actually clear faults because it depends on the page count. Non-cleared faults in its turn may fail the subsequent page count auto-detection. This patch fixes this problem by calling pmbus_clear_fault_page() for currently set page and calling pmbus_clear_faults() after the page count was detected. Cc: stable@vger.kernel.org Signed-off-by:
Dmitry Bazhenov <bazhenov.dn@gmail.com> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Tang Junhui authored
commit 2d6cb6ed upstream. refill->end record the last key of writeback, for example, at the first time, keys (1,128K) to (1,1024K) are flush to the backend device, but the end key (1,1024K) is not included, since the bellow code: if (bkey_cmp(k, refill->end) >= 0) { ret = MAP_DONE; goto out; } And in the next time when we refill writeback keybuf again, we searched key start from (1,1024K), and got a key bigger than it, so the key (1,1024K) missed. This patch modify the above code, and let the end key to be included to the writeback key buffer. Signed-off-by:
Tang Junhui <tang.junhui.linux@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
Coly Li <colyli@suse.de> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Tang Junhui authored
commit 502b2915 upstream. Missed reading IOs are identified by s->cache_missed, not the s->cache_miss, so in trace_bcache_read() using trace_bcache_read to identify whether the IO is missed or not. Signed-off-by:
-
Rafał Miłecki authored
commit 940ec770 upstream. Fixing/optimizing bcm_qspi_bspi_read() performance introduced two changes: 1) It added a loop to read all requested data using multiple BSPI ops. 2) It bumped max size of a single BSPI block request from 256 to 512 B. The later change resulted in occasional BSPI timeouts causing a regression. For some unknown reason hardware doesn't always handle reads as expected when using 512 B chunks. In such cases it may happen that BSPI returns amount of requested bytes without the last 1-3 ones. It provides the remaining bytes later but doesn't raise an interrupt until another LR start. Switching back to 256 B reads fixes that problem and regression. Fixes: 345309fa ("spi: bcm-qspi: Fix bcm_qspi_bspi_read() performance") Signed-off-by:
Rafał Miłecki <rafal@milecki.pl> Signed-off-by:
Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Liu Xiang authored
commit 41fe2429 upstream. If the size of spi-nor flash is larger than 16MB, the read_opcode is set to SPINOR_OP_READ_1_1_4_4B, and fsl_qspi_get_seqid() will return -EINVAL when cmd is SPINOR_OP_READ_1_1_4_4B. This can cause read operation fail. Fixes: e46ecda7 ("mtd: spi-nor: Add Freescale QuadSPI driver") Cc: <stable@vger.kernel.org> Signed-off-by:
Liu Xiang <liu.xiang6@zte.com.cn> Signed-off-by:
-
- 10 Nov, 2018 31 commits
-
-
Greg Kroah-Hartman authored
-
Christophe Leroy authored
[ Upstream commit f8b39039 ] In case of TX timeout, fs_timeout() calls phy_stop(), which triggers the following BUG_ON() as we are in interrupt. [92708.199889] kernel BUG at drivers/net/phy/mdio_bus.c:482! [92708.204985] Oops: Exception in kernel mode, sig: 5 [#1] [92708.210119] PREEMPT [92708.212107] CMPC885 [92708.214216] CPU: 0 PID: 3 Comm: ksoftirqd/0 Tainted: G W 4.9.61 #39 [92708.223227] task: c60f0a40 task.stack: c6104000 [92708.227697] NIP: c02a84bc LR: c02a947c CTR: c02a93d8 [92708.232614] REGS: c6105c70 TRAP: 0700 Tainted: G W (4.9.61) [92708.241193] MSR: 00021032 <ME,IR,DR,RI>[92708.244818] CR: 24000822 XER: 20000000 [92708.248767] GPR00: c02a947c c6105d20 c60f0a40 c62b4c00 00000005 0000001f c069aad8 0001a688 GPR08: 00000007 00000100 c02a93d8 00000000 000005fc 00000000 c6213240 c06338e4 GPR16: 00000001 c06330d4 c0633094 00000000 c0680000 c6104000 c6104000 00000000 GPR24: 00000200 00000000 ffffffff 00000004 00000078 00009032 00000000 c62b4c00 NIP [c02a84bc] mdiobus_read+0x20/0x74 [92708.281517] LR [c02a947c] kszphy_config_intr+0xa4/0xc4 [92708.286547] Call Trace: [92708.288980] [c6105d20] [c6104000] 0xc6104000 (unreliable) [92708.294339] [c6105d40] [c02a947c] kszphy_config_intr+0xa4/0xc4 [92708.300098] [c6105d50] [c02a5330] phy_stop+0x60/0x9c [92708.305007] [c6105d60] [c02c84d0] fs_timeout+0xdc/0x110 [92708.310197] [c6105d80] [c035cd48] dev_watchdog+0x268/0x2a0 [92708.315593] [c6105db0] [c0060288] call_timer_fn+0x34/0x17c [92708.321014] [c6105dd0] [c00605f0] run_timer_softirq+0x21c/0x2e4 [92708.326887] [c6105e50] [c001e19c] __do_softirq+0xf4/0x2f4 [92708.332207] [c6105eb0] [c001e3c8] run_ksoftirqd+0x2c/0x40 [92708.337560] [c6105ec0] [c003b420] smpboot_thread_fn+0x1f0/0x258 [92708.343405] [c6105ef0] [c003745c] kthread+0xbc/0xd0 [92708.348217] [c6105f40] [c000c400] ret_from_kernel_thread+0x5c/0x64 [92708.354275] Instruction dump: [92708.357207] 7c0803a6 bbc10018 38210020 4e800020 7c0802a6 9421ffe0 54290024 bfc10018 [92708.364865] 90010024 7c7f1b78 81290008 552902ee <0f090000> 3bc3002c 7fc3f378 90810008 [92708.372711] ---[ end trace 42b05441616fafd7 ]--- This patch moves fs_timeout() actions into an async worker. Fixes: commit 48257c4f ("Add fs_enet ethernet network driver, for several embedded platforms") Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Sebastian Andrzej Siewior authored
x86/fpu: Fix i486 + no387 boot crash by only saving FPU registers on context switch if there is an FPU commit 2224d616 upstream. Booting an i486 with "no387 nofxsr" ends with with the following crash: math_emulate: 0060:c101987d Kernel panic - not syncing: Math emulation needed in kernel on the first context switch in user land. The reason is that copy_fpregs_to_fpstate() tries FNSAVE which does not work as the FPU is turned off. This bug was introduced in: f1c8cd01 ("x86/fpu: Change fpu->fpregs_active users to fpu->fpstate_active") Add a check for X86_FEATURE_FPU before trying to save FPU registers (we have such a check in switch_fpu_finish() already). Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by:
Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Fixes: f1c8cd01 ("x86/fpu: Change fpu->fpregs_active users to fpu->fpstate_active") Link: http://lkml.kernel.org/r/20181016202525.29437-4-bigeasy@linutronix.deSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Nathan Chancellor authored
commit 53c13ba8 upstream. Clang warns that the declaration of jiffies in include/linux/jiffies.h doesn't match the definition in arch/x86/time/kernel.c: arch/x86/kernel/time.c:29:42: warning: section does not match previous declaration [-Wsection] __visible volatile unsigned long jiffies __cacheline_aligned = INITIAL_JIFFIES; ^ ./include/linux/cache.h:49:4: note: expanded from macro '__cacheline_aligned' __section__(".data..cacheline_aligned"))) ^ ./include/linux/jiffies.h:81:31: note: previous attribute is here extern unsigned long volatile __cacheline_aligned_in_smp __jiffy_arch_data jiffies; ^ ./arch/x86/include/asm/cache.h:20:2: note: expanded from macro '__cacheline_aligned_in_smp' __page_aligned_data ^ ./include/linux/linkage.h:39:29: note: expanded from macro '__page_aligned_data' #define __page_aligned_data __section(.data..page_aligned) __aligned(PAGE_SIZE) ^ ./include/linux/compiler_attributes.h:233:56: note: expanded from macro '__section' #define __section(S) __attribute__((__section__(#S))) ^ 1 warning generated. The declaration was changed in commit 7c30f352 ("jiffies.h: declare jiffies and jiffies_64 with ____cacheline_aligned_in_smp") but wasn't updated here. Make them match so Clang no longer warns. Fixes: 7c30f352 ("jiffies.h: declare jiffies and jiffies_64 with ____cacheline_aligned_in_smp") Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20181013005311.28617-1-natechancellor@gmail.comSigned-off-by:
-
Peter Zijlstra authored
commit b59167ac upstream. Eric reported that a sequence count loop using this_cpu_read() got optimized out. This is wrong, this_cpu_read() must imply READ_ONCE() because the interface is IRQ-safe, therefore an interrupt can have changed the per-cpu value. Fixes: 7c3576d2 ("[PATCH] i386: Convert PDA into the percpu section") Reported-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
-
Zhimin Gu authored
commit cc55f753 upstream. On 32bit systems, nosave_regions(non RAM areas) located between max_low_pfn and max_pfn are not excluded from hibernation snapshot currently, which may result in a machine check exception when trying to access these unsafe regions during hibernation: [ 612.800453] Disabling lock debugging due to kernel taint [ 612.805786] mce: [Hardware Error]: CPU 0: Machine Check Exception: 5 Bank 6: fe00000000801136 [ 612.814344] mce: [Hardware Error]: RIP !INEXACT! 60:<00000000d90be566> {swsusp_save+0x436/0x560} [ 612.823167] mce: [Hardware Error]: TSC 1f5939fe276 ADDR dd000000 MISC 30e0000086 [ 612.830677] mce: [Hardware Error]: PROCESSOR 0:306c3 TIME 1529487426 SOCKET 0 APIC 0 microcode 24 [ 612.839581] mce: [Hardware Error]: Run the above through 'mcelog --ascii' [ 612.846394] mce: [Hardware Error]: Machine check: Processor context corrupt [ 612.853380] Kernel panic - not syncing: Fatal machine check [ 612.858978] Kernel Offset: 0x18000000 from 0xc1000000 (relocation range: 0xc0000000-0xf7ffdfff) This is because on 32bit systems, pages above max_low_pfn are regarded as high memeory, and accessing unsafe pages might cause expected MCE. On the problematic 32bit system, there are reserved memory above low memory, which triggered the MCE: e820 memory mapping: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000d160cfff] usable [ 0.000000] BIOS-e820: [mem 0x00000000d160d000-0x00000000d1613fff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000d1614000-0x00000000d1a44fff] usable [ 0.000000] BIOS-e820: [mem 0x00000000d1a45000-0x00000000d1ecffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000d1ed0000-0x00000000d7eeafff] usable [ 0.000000] BIOS-e820: [mem 0x00000000d7eeb000-0x00000000d7ffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000d8000000-0x00000000d875ffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000d8760000-0x00000000d87fffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000d8800000-0x00000000d8fadfff] usable [ 0.000000] BIOS-e820: [mem 0x00000000d8fae000-0x00000000d8ffffff] ACPI data [ 0.000000] BIOS-e820: [mem 0x00000000d9000000-0x00000000da71bfff] usable [ 0.000000] BIOS-e820: [mem 0x00000000da71c000-0x00000000da7fffff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000da800000-0x00000000dbb8bfff] usable [ 0.000000] BIOS-e820: [mem 0x00000000dbb8c000-0x00000000dbffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000dd000000-0x00000000df1fffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000041edfffff] usable Fix this problem by changing pfn limit from max_low_pfn to max_pfn. This fix does not impact 64bit system because on 64bit max_low_pfn is the same as max_pfn. Signed-off-by:
Zhimin Gu <kookoo.gu@intel.com> Acked-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
Chen Yu <yu.c.chen@intel.com> Acked-by:
-
Peter Zijlstra authored
commit 4907c68a upstream. Looking at the asm for native_sched_clock() I noticed we don't inline enough. Mostly caused by sharing code with cyc2ns_read_begin(), which we didn't used to do. So mark all that __force_inline to make it DTRT. Fixes: 59eaef78 ("x86/tsc: Remodel cyc2ns to use seqcount_latch()") Reported-by:
-
Phil Auld authored
commit baa9be4f upstream. With a very low cpu.cfs_quota_us setting, such as the minimum of 1000, distribute_cfs_runtime may not empty the throttled_list before it runs out of runtime to distribute. In that case, due to the change from c06f04c7 to put throttled entries at the head of the list, later entries on the list will starve. Essentially, the same X processes will get pulled off the list, given CPU time and then, when expired, get put back on the head of the list where distribute_cfs_runtime will give runtime to the same set of processes leaving the rest. Fix the issue by setting a bit in struct cfs_bandwidth when distribute_cfs_runtime is running, so that the code in throttle_cfs_rq can decide to put the throttled entry on the tail or the head of the list. The bit is set/cleared by the callers of distribute_cfs_runtime while they hold cfs_bandwidth->lock. This is easy to reproduce with a handful of CPU consumers. I use 'crash' on the live system. In some cases you can simply look at the throttled list and see the later entries are not changing: crash> list cfs_rq.throttled_list -H 0xffff90b54f6ade40 -s cfs_rq.runtime_remaining | paste - - | awk '{print $1" "$4}' | pr -t -n3 1 ffff90b56cb2d200 -976050 2 ffff90b56cb2cc00 -484925 3 ffff90b56cb2bc00 -658814 4 ffff90b56cb2ba00 -275365 5 ffff90b166a45600 -135138 6 ffff90b56cb2da00 -282505 7 ffff90b56cb2e000 -148065 8 ffff90b56cb2fa00 -872591 9 ffff90b56cb2c000 -84687 10 ffff90b56cb2f000 -87237 11 ffff90b166a40a00 -164582 crash> list cfs_rq.throttled_list -H 0xffff90b54f6ade40 -s cfs_rq.runtime_remaining | paste - - | awk '{print $1" "$4}' | pr -t -n3 1 ffff90b56cb2d200 -994147 2 ffff90b56cb2cc00 -306051 3 ffff90b56cb2bc00 -961321 4 ffff90b56cb2ba00 -24490 5 ffff90b166a45600 -135138 6 ffff90b56cb2da00 -282505 7 ffff90b56cb2e000 -148065 8 ffff90b56cb2fa00 -872591 9 ffff90b56cb2c000 -84687 10 ffff90b56cb2f000 -87237 11 ffff90b166a40a00 -164582 Sometimes it is easier to see by finding a process getting starved and looking at the sched_info: crash> task ffff8eb765994500 sched_info PID: 7800 TASK: ffff8eb765994500 CPU: 16 COMMAND: "cputest" sched_info = { pcount = 8, run_delay = 697094208, last_arrival = 240260125039, last_queued = 240260327513 }, crash> task ffff8eb765994500 sched_info PID: 7800 TASK: ffff8eb765994500 CPU: 16 COMMAND: "cputest" sched_info = { pcount = 8, run_delay = 697094208, last_arrival = 240260125039, last_queued = 240260327513 }, Signed-off-by:
Phil Auld <pauld@redhat.com> Reviewed-by:
Ben Segall <bsegall@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Fixes: c06f04c7 ("sched: Fix potential near-infinite distribute_cfs_runtime() loop") Link: http://lkml.kernel.org/r/20181008143639.GA4019@pauld.bos.csbSigned-off-by:
-
Mikhail Nikiforov authored
commit 13c1c5e4 upstream. Add ELAN061C to the ACPI table to support Elan touchpad found in Lenovo IdeaPad 330-15IGM. Signed-off-by:
Mikhail Nikiforov <jackxviichaos@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Alan Stern authored
commit 665c365a upstream. Commit 7a68d9fb ("USB: usbdevfs: sanitize flags more") checks the transfer flags for URBs submitted from userspace via usbfs. However, the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be allowed for a control transfer was added in the wrong place, before the code has properly determined the direction of the control transfer. (Control transfers are special because for them, the direction is set by the bRequestType byte of the Setup packet rather than direction bit of the endpoint address.) This patch moves code which sets up the allow_short flag for control transfers down after is_in has been set to the correct value. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: syzbot+24a30223a4b609bb802e@syzkaller.appspotmail.com Fixes: 7a68d9fb ("USB: usbdevfs: sanitize flags more") CC: Oliver Neukum <oneukum@suse.com> CC: <stable@vger.kernel.org> Signed-off-by:
-
Gustavo A. R. Silva authored
commit 9ae24af3 upstream. num can be indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: drivers/usb/gadget/function/f_mass_storage.c:3177 fsg_lun_make() warn: potential spectre issue 'fsg_opts->common->luns' [r] (local cap) Fix this by sanitizing num before using it to index fsg_opts->common->luns Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2 Cc: stable@vger.kernel.org Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by:
Felipe Balbi <felipe.balbi@intel.com> Signed-off-by:
-
Shuah Khan (Samsung OSG) authored
commit 81f7567c upstream. vhci_hub_control() accesses port_status array with out of bounds port value. Fix it to reference port_status[] only with a valid rhport value when invalid_rhport flag is true. The invalid_rhport flag is set early on after detecting in port value is within the bounds or not. The following is used reproduce the problem and verify the fix: C reproducer: https://syzkaller.appspot.com/x/repro.c?x=14ed8ab6400000 Reported-by: syzbot+bccc1fe10b70fadc78d0@syzkaller.appspotmail.com Cc: stable <stable@vger.kernel.org> Signed-off-by:
Shuah Khan (Samsung OSG) <shuah@kernel.org> Signed-off-by:
-
Oliver Neukum authored
commit 9397940e upstream. If a device splits up a control message and a reset() happens between the parts, the message is lost and already recieved parts must be dropped. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Fixes: 1aba579f ("cdc-acm: handle read pipe errors") Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Tobias Herzog authored
commit f976d0e5 upstream. The usb standard ("Universal Serial Bus Class Definitions for Communication Devices") distiguishes between "consistent signals" (DSR, DCD), and "irregular signals" (break, ring, parity error, framing error, overrun). The bits of "irregular signals" are set, if this error/event occurred on the device side and are immeadeatly unset, if the serial state notification was sent. Like other drivers of real serial ports do, just the occurence of those events should be counted in serial_icounter_struct (but no 1->0 transitions). Signed-off-by:
Tobias Herzog <t-herzog@gmx.de> Acked-by:
-
Tobias Herzog authored
commit dae3ddba upstream. Resetting the write index of the notification buffer on urb unlink (e.g. closing a cdc-acm device from userspace) may lead to wrong interpretation of further received notifications, in case the index is not 0 when urb unlink happens (i.e. when parts of a notification already have been transferred). On the device side there is no "reset" of the notification transimission and thus we would get out of sync with the device. Signed-off-by:
-
Gustavo A. R. Silva authored
commit 0295e395 upstream. hdr.cmd can be indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: drivers/infiniband/core/ucm.c:1127 ib_ucm_write() warn: potential spectre issue 'ucm_cmd_table' [r] (local cap) Fix this by sanitizing hdr.cmd before using it to index ucm_cmd_table. Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2 Cc: stable@vger.kernel.org Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Gustavo A. R. Silva authored
commit a3671a4f upstream. hdr.cmd can be indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: drivers/infiniband/core/ucma.c:1686 ucma_write() warn: potential spectre issue 'ucma_cmd_table' [r] (local cap) Fix this by sanitizing hdr.cmd before using it to index ucm_cmd_table. Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2 Cc: stable@vger.kernel.org Signed-off-by:
-
Eugeniy Paltsev authored
commit db05c481 upstream. drm fbdev emulation doesn't support changing the pixel format at all, so reject all pixel format changing requests. Cc: stable@vger.kernel.org Signed-off-by:
Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20181003164538.5534-1-Eugeniy.Paltsev@synopsys.comSigned-off-by:
-
Clint Taylor authored
commit 9068e02f upstream. HDMI Forum VSDB YCBCR420 deep color capability bits are 2:0. Correct definitions in the header for the mask to work correctly. Fixes: e6a9a2c3 ("drm/edid: parse ycbcr 420 deep color information") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107893 Cc: <stable@vger.kernel.org> # v4.14+ Signed-off-by:
Clint Taylor <clinton.a.taylor@intel.com> Reviewed-by:
Jani Nikula <jani.nikula@intel.com> Reviewed-by:
Shashank Sharma <shashank.sharma@intel.com> Signed-off-by:
-
Kai-Heng Feng authored
commit 0711a43b upstream. There's another panel that reports "DFP 1.x compliant TMDS" but it supports 6bpc instead of 8 bpc. Apply 6 bpc quirk for the panel to fix it. BugLink: https://bugs.launchpad.net/bugs/1794387 Cc: <stable@vger.kernel.org> # v4.8+ Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
-
Gustavo A. R. Silva authored
commit efa61c8c upstream. pin_index can be indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: drivers/ptp/ptp_chardev.c:253 ptp_ioctl() warn: potential spectre issue 'ops->pin_config' [r] (local cap) Fix this by sanitizing pin_index before using it to index ops->pin_config, and before passing it as an argument to function ptp_set_pinfunc(), in which it is used to index info->pin_config. Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2 Cc: stable@vger.kernel.org Signed-off-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Al Viro authored
commit 169b8033 upstream. the victim might've been rmdir'ed just before the lock_rename(); unlike the normal callers, we do not look the source up after the parents are locked - we know it beforehand and just recheck that it's still the child of what used to be its parent. Unfortunately, the check is too weak - we don't spot a dead directory since its ->d_parent is unchanged, dentry is positive, etc. So we sail all the way to ->rename(), with hosting filesystems _not_ expecting to be asked renaming an rmdir'ed subdirectory. The fix is easy, fortunately - the lock on parent is sufficient for making IS_DEADDIR() on child safe. Cc: stable@vger.kernel.org Fixes: 9ae326a6 (CacheFiles: A cache that backs onto a mounted filesystem) Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Brian Foster authored
[ Upstream commit a606ebdb ] The truncate transaction does not ever modify the inode btree, but includes an associated log reservation. Update xfs_calc_itruncate_reservation() to remove the reservation associated with inobt updates. [Amir: This commit was merged for kernel v4.16 and a twin commit was merged for xfsprogs v4.16. As a result, a small xfs filesystem formatted with features -m rmapbt=1,reflink=1 using mkfs.xfs version >= v4.16 cannot be mounted with kernel < v4.16. For example, xfstests generic/17{1,2,3} format a small fs and when trying to mount it, they fail with an assert on this very demonic line: XFS (vdc): Log size 3075 blocks too small, minimum size is 3717 blocks XFS (vdc): AAIEEE! Log failed size checks. Abort! XFS: Assertion failed: 0, file: src/linux/fs/xfs/xfs_log.c, line: 666 The simple solution for stable kernels is to apply this patch, because mkfs.xfs v4.16 is already in the wild, so we have to assume that xfs filesystems with a "too small" log exist. Regardless, xfsprogs maintainers should also consider reverting the twin patch to stop creating those filesystems for the sake of users with unpatched kernels.] Signed-off-by:
Brian Foster <bfoster@redhat.com> Reviewed-by:
Dave Chinner <dchinner@redhat.com> Reviewed-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
Amir Goldstein <amir73il@gmail.com> Reviewed-by:
-
Linus Walleij authored
[ Upstream commit 833eacc7 ] The MXS driver was calling back into the GPIO API from its irqchip. This is not very elegant, as we are a driver, let's just shortcut back into the gpio_chip .get() function instead. This is a tricky case since the .get() callback is not in this file, instead assigned by bgpio_init(). Calling the function direcly in the gpio_chip is however the lesser evil. Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Janusz Uzycki <j.uzycki@elproma.com.pl> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Amir Goldstein authored
[ Upstream commit 9bdda4e9 ] Commit 92183a42 ("fsnotify: fix ignore mask logic in send_to_group()") acknoledges the use case of ignoring an event on an inode mark, because of an ignore mask on a mount mark of the same group (i.e. I want to get all events on this file, except for the events that came from that mount). This change depends on correctly merging the inode marks and mount marks group lists, so that the mount mark ignore mask would be tested in send_to_group(). Alas, the merging of the lists did not take into account the case where event in question is not in the mask of any of the mount marks. To fix this, completely remove the tests for inode and mount event masks from the lists merging code. Fixes: 92183a42 ("fsnotify: fix ignore mask logic in send_to_group") Signed-off-by:
Jan Kara <jack@suse.cz> [amir: backport to v4.14.y] Signed-off-by:
-
Sasha Levin authored
This reverts commit b39ac542. The issue was fixed by upstream commit 5d797111 ("clk: tegra: Add quirk for getting CDEV1/2 clocks on Tegra20"). Signed-off-by:
-
Daniel Borkmann authored
commit 0962590e upstream. ALU operations on pointers such as scalar_reg += map_value_ptr are handled in adjust_ptr_min_max_vals(). Problem is however that map_ptr and range in the register state share a union, so transferring state through dst_reg->range = ptr_reg->range is just buggy as any new map_ptr in the dst_reg is then truncated (or null) for subsequent checks. Fix this by adding a raw member and use it for copying state over to dst_reg. Fixes: f1174f77 ("bpf/verifier: rework value tracking") Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Cc: Edward Cree <ecree@solarflare.com> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
Edward Cree <ecree@solarflare.com> Signed-off-by:
-
Johan Hovold authored
commit 35aecc02 upstream Allow matching on interfaces having two endpoints by adding a new device-id flag. This allows for the handling of devices whose interface numbers can change (e.g. Quectel EP06) to be contained in the device-id table. The upstream commit removes a variable that is still in use in the 4.14 version of the option-driver, so the removal is undone. Tested-by:
Kristian Evensen <kristian.evensen@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Kristian Evensen authored
commit 36cae568 upstream The Quectel EP06 (and EM06/EG06) LTE modem supports updating the USB configuration, without the VID/PID or configuration number changing. When the configuration is updated and interfaces are added/removed, the interface numbers are updated. This causes our current code for matching EP06 not to work as intended, as the assumption about reserved interfaces no longer holds. If for example the diagnostic (first) interface is removed, option will (try to) bind to the QMI interface. This patch improves EP06 detection by replacing the current match with two matches, and those matches check class, subclass and protocol as well as VID and PID. The diag interface exports class, subclass and protocol as 0xff. For the other serial interfaces, class is 0xff and subclass and protocol are both 0x0. The modem can export the following devices and always in this order: diag, nmea, at, ppp. qmi and adb. This means that diag can only ever be interface 0, and interface numbers 1-5 should be marked as reserved. The three other serial devices can have interface numbers 0-3, but I have not marked any interfaces as reserved. The reason is that the serial devices are the only interfaces exported by the device where subclass and protocol is 0x0. QMI exports the same class, subclass and protocol values as the diag interface. However, the two interfaces have different number of endpoints, QMI has three and diag two. I have added a check for number of interfaces if VID/PID matches the EP06, and we ignore the device if number of interfaces equals three (and subclass is set). The upstream commit does not apply cleanly to the 4.14-tree because of differences in option_probe(). In order to make the commit apply, a slight reshuffeling of the code was needed. Signed-off-by:
Dan Williams <dcbw@redhat.com> [ johan: drop uneeded RSVD(5) for ADB ] Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Amir Goldstein authored
commit a725356b upstream. Commit 031a072a ("vfs: call vfs_clone_file_range() under freeze protection") created a wrapper do_clone_file_range() around vfs_clone_file_range() moving the freeze protection to former, so overlayfs could call the latter. The more common vfs practice is to call do_xxx helpers from vfs_xxx helpers, where freeze protecction is taken in the vfs_xxx helper, so this anomality could be a source of confusion. It seems that commit 8ede2055 ("ovl: add reflink/copyfile/dedup support") may have fallen a victim to this confusion - ovl_clone_file_range() calls the vfs_clone_file_range() helper in the hope of getting freeze protection on upper fs, but in fact results in overlayfs allowing to bypass upper fs freeze protection. Swap the names of the two helpers to conform to common vfs practice and call the correct helpers from overlayfs and nfsd. Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Fixes: 031a072a ("vfs: call vfs_clone_file_range() under freeze...") Signed-off-by:
-
Alan Chiang authored
[ Upstream commit a2b3bf48 ] Provide a flexible way to determine the addressing bits of eeprom. Pass the addressing bits to driver through address-width property. Signed-off-by:
Alan Chiang <alanx.chiang@intel.com> Signed-off-by:
Andy Yeh <andy.yeh@intel.com> Signed-off-by:
Bartosz Golaszewski <brgl@bgdev.pl> Signed-off-by:
-
- 04 Nov, 2018 2 commits
-
-
Greg Kroah-Hartman authored
-
Saeed Mahameed authored
[ Upstream commit e3ca3488 ] Avoid using the kernel's irq_descriptor and return IRQ vector affinity directly from the driver. This fixes the following build break when CONFIG_SMP=n include/linux/mlx5/driver.h: In function ‘mlx5_get_vector_affinity_hint’: include/linux/mlx5/driver.h:1299:13: error: ‘struct irq_desc’ has no member named ‘affinity_hint’ Fixes: 6082d9c9 ("net/mlx5: Fix mlx5_get_vector_affinity function") Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> CC: Randy Dunlap <rdunlap@infradead.org> CC: Guenter Roeck <linux@roeck-us.net> CC: Thomas Gleixner <tglx@linutronix.de> Tested-by:
Israel Rukshin <israelr@mellanox.com> Reported-by:
kbuild test robot <lkp@intel.com> Reported-by:
Randy Dunlap <rdunlap@infradead.org> Tested-by:
-
