The ZII devel B board has two generations of Marvell Switches.  The
mv88e6352 supports an MDIO clock of 12MHz. However the older 88e6185
does not like 12MHz, and often fails to probe.

Reduce the clock speed to 5MHz, which seems to work reliably.

Cc: Chris Healy <cphealy@gmail.com>
Fixes: b9553876 ("ARM: dts: ZII: update MDIO speed and preamble")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Commit bcf3440c ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") fixed micrel phy driver adding proper support for phy
modes. Adapt imx6q-udoo board phy settings : explicitly set required
delay configuration using "rgmii-id".

Fixes: cbd54fe0 ("ARM: dts: imx6dl-udoo: Add board support based off imx6q-udoo")
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Due to bug in the bootloader, the PHY has floating address and may
randomly change on each PHY reset. To avoid it, the updated bootloader
with the following patch[0] should be used:

| ARM: protonic: disable on-die termination to fix PHY bootstrapping
|
| If on-die termination is enabled, the RXC pin of iMX6 will be pulled
| high. Since we already have an 10K pull-down on board, the RXC level on
| PHY reset will be ~800mV, which is mostly interpreted as 1. On some
| reboots we get 0 instead and kernel can't detect the PHY properly.
|
| Since the default 0x020e07ac value is 0, it is sufficient to remove this
| entry from the affected imxcfg files.
|
| Since we get stable 0 on pin PHYADDR[2], the PHY address is changed from
| 4 to 0.

With latest bootloader update, the PHY address will be fixed to "0".

[0] https://git.pengutronix.de/cgit/barebox/commit/?id=93f7dcf631edfcda19e7757b28d66017ea274b81

Fixes: 0d446a50 ("ARM: dts: add Protonic PRTI6Q board")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to the i.MX8MN TRM, there is only one OTG port.  The
address for OTG2 is reserved on Nano.

This patch removes the non-existent OTG2, usbphynop2, and the usbmisc2
nodes.

Fixes: 6c3debcb ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

When streaming bluetooth audio, the sound is choppy due to the
fact that the default baud rate of the HCI interface is too slow
to handle 16-bit stereo at 48KHz.

The Bluetooth chip is capable of up to 4M baud on the serial port,
so this patch sets the max-speed to 4000000 in order to properly
stream audio over the Bluetooth.

Fixes: 593816fa ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Although the DPAA 1 FMan operations are coherent, the device tree
node for the FMan does not indicate that, resulting in a needless
loss of performance. Adding the missing dma-coherent property.

Fixes: 1ffbecdd ("arm64: dts: add DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@oss.nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add little-endian property to RCPM node (for ls1028a,ls1088a,ls208xa),
otherwise RCPM driver will program hardware with incorrect setting,
causing system (such as LS1028ARDB) failed to be waked by wakeup source.

Fixes: 791c88ca (“arm64: dts: ls1028a: Add ftm_alarm0 DT node”)
Fixes: f4fe3a86 (“arm64: dts: layerscape: add ftm_alarm0 node”)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PMIC's interrupt is level low and should be pulled up.  The PMIC's
device node had pinctrl-0 property but it lacked pinctrl-names which
is required to apply the pin configuration.

Fixes: 4153f781 ("arm64: dts: imx8mn: correct interrupt flags")
Fixes: 6386156e ("arm64: dts: imx8mn-evk: add pca9450 for i.mx8mn-evk board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PMIC's interrupt is level low and should be pulled up.  The PMIC's
device node had pinctrl-0 property but it lacked pinctrl-names which
is required to apply the pin configuration.

Fixes: 4153f781 ("arm64: dts: imx8mn: correct interrupt flags")
Fixes: 3e44dd09 ("arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PMIC's interrupt is level low and should be pulled up.  The PMIC's
device node had pinctrl-0 property but it lacked pinctrl-names which
is required to apply the pin configuration.  The actual problem in DTS
was pointed out by Felix Radensky from Variscite.
Reported-by: Felix Radensky <felix.r@variscite.com>
Fixes: ade0176d ("arm64: dts: imx8mn-var-som: Add Variscite VAR-SOM-MX8MN System on Module")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PMIC's interrupt is level low and should be pulled up.  The PMIC's
device node had pinctrl-0 property but it lacked pinctrl-names which
is required to apply the pin configuration.

Fixes: 5f67317b ("arm64: dts: imx8mm: correct interrupt flags")
Fixes: aa71d064 ("arm64: dts: imx8mm: Split the imx8mm evk board dts to a common dtsi")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PMIC's interrupt is level low and should be pulled up.  The PMIC's
device node had pinctrl-0 property but it lacked pinctrl-names which
is required to apply the pin configuration.

Fixes: 5f67317b ("arm64: dts: imx8mm: correct interrupt flags")
Fixes: 593816fa ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PMIC's interrupt is level low and should be pulled up.  The PMIC's
device node had pinctrl-0 property but it lacked pinctrl-names which
is required to apply the pin configuration.  The actual problem in DTS
was pointed out by Felix Radensky from Variscite.
Reported-by: Felix Radensky <felix.r@variscite.com>
Fixes: 5f67317b ("arm64: dts: imx8mm: correct interrupt flags")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since commit 12d16b39 ("gpio: mxc: Support module build") the
CONFIG_GPIO_MXC option needs to be explicitly selected.

Select it to avoid boot issues on imx25/imx27 due to the lack of the
GPIO driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since commit 12d16b39 ("gpio: mxc: Support module build") the
CONFIG_GPIO_MXC option needs to be explicitly selected.

Select it to avoid boot issues on imx25/imx27 due to the lack of the
GPIO driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX SoC GPIO driver provides the basic functions of GPIO pin operations
and IRQ operations, it is now changed from "def_bool y" to "tristate", so
it should be explicitly enabled to make sure all consumers work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX SoC GPIO driver provides the basic functions of GPIO pin operations
and IRQ operations, it is now changed from "def_bool y" to "tristate", so
it should be explicitly enabled to make sure all consumers work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX SoC GPIO driver provides the basic functions of GPIO pin operations
and IRQ operations, it is now changed from "def_bool y" to "tristate", so
it should be explicitly enabled to make sure all consumers work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.

Remove the quote operator # from compiler_attributes.h __section macro.

Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.

Conversion done using the script at:

    https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.plSigned-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace".  So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 453431a5 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.

Since then a few more instances of kzfree() have slipped in.

Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.

If GIT_DIR is unset, keep using the current ".git" default.

Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.comSigned-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:
 "A time namespace fix and a matching selftest. The futex absolute
  timeouts which are based on CLOCK_MONOTONIC require time namespace
  corrected. This was missed in the original time namesapce support"

* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  selftests/timens: Add a test for futex()
  futex: Adjust absolute futex timeouts with per time namespace offset

Pull scheduler fixes from Thomas Gleixner:
 "Two scheduler fixes:

   - A trivial build fix for sched_feat() to compile correctly with
     CONFIG_JUMP_LABEL=n

   - Replace a zero lenght array with a flexible array"

* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/features: Fix !CONFIG_JUMP_LABEL case
  sched: Replace zero-length array with flexible-array

Pull perf fix from Thomas Gleixner:
 "A single fix to compute the field offset of the SNOOPX bit in the data
  source bitmask of perf events correctly"

* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: correct SNOOPX field offset

Pull locking fix from Thomas Gleixner:
 "Just a trivial fix for kernel-doc warnings"

* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/seqlocks: Fix kernel-doc warnings

Pull NTB fixes from Jon Mason.

* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
  NTB: Use struct_size() helper in devm_kzalloc()
  ntb: intel: Fix memleak in intel_ntb_pci_probe
  NTB: hw: amd: fix an issue about leak system resources

Pull i2c fix from Wolfram Sang:
 "Regression fix for rc1 and stable kernels as well"

* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs

Pull more cifs updates from Steve French:
 "Add support for stat of various special file types (WSL reparse points
  for char, block, fifo)"

* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number
  smb3: add some missing definitions from MS-FSCC
  smb3: remove two unused variables
  smb3: add support for stat of WSL reparse points for special file types

Pull more parisc updates from Helge Deller:

 - During this merge window O_NONBLOCK was changed to become 000200000,
   but we missed that the syscalls timerfd_create(), signalfd4(),
   eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
   bit-wise check of the flags parameter.

   To provide backward compatibility with existing userspace we
   introduce parisc specific wrappers for those syscalls which filter
   out the old O_NONBLOCK value and replaces it with the new one.

 - Prevent HIL bus driver to get stuck when keyboard or mouse isn't
   attached

 - Improve error return codes when setting rtc time

 - Minor documentation fix in pata_ns87415.c

* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  ata: pata_ns87415.c: Document support on parisc with superio chip
  parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
  hil/parisc: Disable HIL driver when it gets stuck
  parisc: Improve error return codes when setting rtc time

Pull more xen updates from Juergen Gross:

 - a series for the Xen pv block drivers adding module parameters for
   better control of resource usge

 - a cleanup series for the Xen event driver

* tag 'for-linus-5.10b-rc1c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  Documentation: add xen.fifo_events kernel parameter description
  xen/events: unmask a fifo event channel only if it was masked
  xen/events: only register debug interrupt for 2-level events
  xen/events: make struct irq_info private to events_base.c
  xen: remove no longer used functions
  xen-blkfront: Apply changed parameter name to the document
  xen-blkfront: add a parameter for disabling of persistent grants
  xen-blkback: add a parameter for disabling of persistent grants

Pull SafeSetID updates from Micah Morton:
 "The changes are mostly contained to within the SafeSetID LSM, with the
  exception of a few 1-line changes to change some ns_capable() calls to
  ns_capable_setid() -- causing a flag (CAP_OPT_INSETID) to be set that
  is examined by SafeSetID code and nothing else in the kernel.

  The changes to SafeSetID internally allow for setting up GID
  transition security policies, as already existed for UIDs"

* tag 'safesetid-5.10' of git://github.com/micah-morton/linux:
  LSM: SafeSetID: Fix warnings reported by test bot
  LSM: SafeSetID: Add GID security policy handling
  LSM: Signal to SafeSetID when setting group IDs

Pull random32 updates from Willy Tarreau:
 "Make prandom_u32() less predictable.

  This is the cleanup of the latest series of prandom_u32
  experimentations consisting in using SipHash instead of Tausworthe to
  produce the randoms used by the network stack.

  The changes to the files were kept minimal, and the controversial
  commit that used to take noise from the fast_pool (f227e3ec) was
  reverted. Instead, a dedicated "net_rand_noise" per_cpu variable is
  fed from various sources of activities (networking, scheduling) to
  perturb the SipHash state using fast, non-trivially predictable data,
  instead of keeping it fully deterministic. The goal is essentially to
  make any occasional memory leakage or brute-force attempt useless.

  The resulting code was verified to be very slightly faster on x86_64
  than what is was with the controversial commit above, though this
  remains barely above measurement noise. It was also tested on i386 and
  arm, and build- tested only on arm64"

Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/

* tag '20201024-v4-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wtarreau/prandom:
  random32: add a selftest for the prandom32 code
  random32: add noise from network and scheduling activity
  random32: make prandom_u32() output unpredictable

Commit 21653a41 ("i2c: core: Call i2c_acpi_install_space_handler()
before i2c_acpi_register_devices()")'s intention was to only move the
acpi_install_address_space_handler() call to the point before where
the ACPI declared i2c-children of the adapter where instantiated by
i2c_acpi_register_devices().

But i2c_acpi_install_space_handler() had a call to
acpi_walk_dep_device_list() hidden (that is I missed it) at the end
of it, so as an unwanted side-effect now acpi_walk_dep_device_list()
was also being called before i2c_acpi_register_devices().

Move the acpi_walk_dep_device_list() call to the end of
i2c_acpi_register_devices(), so that it is once again called *after*
the i2c_client-s hanging of the adapter have been created.

This fixes the Microsoft Surface Go 2 hanging at boot.

Fixes: 21653a41 ("i2c: core: Call i2c_acpi_install_space_handler() before i2c_acpi_register_devices()")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209627Reported-by: Rainer Finke <rainer@finke.cc>
Reported-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Suggested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Pull block fixes from Jens Axboe:

 - NVMe pull request from Christoph
     - rdma error handling fixes (Chao Leng)
     - fc error handling and reconnect fixes (James Smart)
     - fix the qid displace when tracing ioctl command (Keith Busch)
     - don't use BLK_MQ_REQ_NOWAIT for passthru (Chaitanya Kulkarni)
     - fix MTDT for passthru (Logan Gunthorpe)
     - blacklist Write Same on more devices (Kai-Heng Feng)
     - fix an uninitialized work struct (zhenwei pi)"

 - lightnvm out-of-bounds fix (Colin)

 - SG allocation leak fix (Doug)

 - rnbd fixes (Gioh, Guoqing, Jack)

 - zone error translation fixes (Keith)

 - kerneldoc markup fix (Mauro)

 - zram lockdep fix (Peter)

 - Kill unused io_context members (Yufen)

 - NUMA memory allocation cleanup (Xianting)

 - NBD config wakeup fix (Xiubo)

* tag 'block-5.10-2020-10-24' of git://git.kernel.dk/linux-block: (27 commits)
  block: blk-mq: fix a kernel-doc markup
  nvme-fc: shorten reconnect delay if possible for FC
  nvme-fc: wait for queues to freeze before calling update_hr_hw_queues
  nvme-fc: fix error loop in create_hw_io_queues
  nvme-fc: fix io timeout to abort I/O
  null_blk: use zone status for max active/open
  nvmet: don't use BLK_MQ_REQ_NOWAIT for passthru
  nvmet: cleanup nvmet_passthru_map_sg()
  nvmet: limit passthru MTDS by BIO_MAX_PAGES
  nvmet: fix uninitialized work for zero kato
  nvme-pci: disable Write Zeroes on Sandisk Skyhawk
  nvme: use queuedata for nvme_req_qid
  nvme-rdma: fix crash due to incorrect cqe
  nvme-rdma: fix crash when connect rejected
  block: remove unused members for io_context
  blk-mq: remove the calling of local_memory_node()
  zram: Fix __zram_bvec_{read,write}() locking order
  skd_main: remove unused including <linux/version.h>
  sgl_alloc_order: fix memory leak
  lightnvm: fix out-of-bounds write to array devices->info[]
  ...

Pull io_uring fixes from Jens Axboe:

 - fsize was missed in previous unification of work flags

 - Few fixes cleaning up the flags unification creds cases (Pavel)

 - Fix NUMA affinities for completely unplugged/replugged node for io-wq

 - Two fallout fixes from the set_fs changes. One local to io_uring, one
   for the splice entry point that io_uring uses.

 - Linked timeout fixes (Pavel)

 - Removal of ->flush() ->files work-around that we don't need anymore
   with referenced files (Pavel)

 - Various cleanups (Pavel)

* tag 'io_uring-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
  splice: change exported internal do_splice() helper to take kernel offset
  io_uring: make loop_rw_iter() use original user supplied pointers
  io_uring: remove req cancel in ->flush()
  io-wq: re-set NUMA node affinities if CPUs come online
  io_uring: don't reuse linked_timeout
  io_uring: unify fsize with def->work_flags
  io_uring: fix racy REQ_F_LINK_TIMEOUT clearing
  io_uring: do poll's hash_node init in common code
  io_uring: inline io_poll_task_handler()
  io_uring: remove extra ->file check in poll prep
  io_uring: make cached_cq_overflow non atomic_t
  io_uring: inline io_fail_links()
  io_uring: kill ref get/drop in personality init
  io_uring: flags-based creds init in queue

Pull libata fixes from Jens Axboe:
 "Two minor libata fixes:

   - Fix a DMA boundary mask regression for sata_rcar (Geert)

   - kerneldoc markup fix (Mauro)"

* tag 'libata-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
  ata: fix some kernel-doc markups
  ata: sata_rcar: Fix DMA boundary mask

Pull misc vfs updates from Al Viro:
 "Assorted stuff all over the place (the largest group here is
  Christoph's stat cleanups)"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: remove KSTAT_QUERY_FLAGS
  fs: remove vfs_stat_set_lookup_flags
  fs: move vfs_fstatat out of line
  fs: implement vfs_stat and vfs_lstat in terms of vfs_fstatat
  fs: remove vfs_statx_fd
  fs: omfs: use kmemdup() rather than kmalloc+memcpy
  [PATCH] reduce boilerplate in fsid handling
  fs: Remove duplicated flag O_NDELAY occurring twice in VALID_OPEN_FLAGS
  selftests: mount: add nosymfollow tests
  Add a "nosymfollow" mount option.

Pull dma-mapping fixes from Christoph Hellwig:

 - document the new dma_{alloc,free}_pages() API

 - two fixups for the dma-mapping.h split

* tag 'dma-mapping-5.10-1' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: document dma_{alloc,free}_pages
  dma-mapping: move more functions to dma-map-ops.h
  ARM/sa1111: add a missing include of dma-map-ops.h