Since the req_speeds field in struct ice_link_status is a u8,
req_speeds & ICE_AQ_LINK_SPEED_40GB always returns 0. This was caught
by a coverity scan.

Fix this by changing req_speeds to be u16.
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The timecounter needs to be updated at least once per ~550 seconds in
order to avoid a 40-bit SYSTIM timestamp to be misinterpreted as an old
timestamp.

Since commit 500462a9 ("timers: Switch to a non-cascading wheel"),
scheduling of delayed work seems to be less accurate and a requested
delay of 540 seconds may actually be longer than 550 seconds. Also, the
PHC may be adjusted to run up to 6% faster than real time and the system
clock up to 10% slower. Shorten the delay to 360 seconds to be sure the
timecounter is updated in time.

This fixes an issue with HW timestamps on 82580/I350/I354 being off by
~1100 seconds for few seconds every ~9 minutes.

Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if the driver does a TSO offload the bytecount sent to
netdev_tx_sent_queue will be incorrect. This is because in ice_tso we
overwrite the initial value that we set in ice_tx_map. This creates a
mismatch between the Tx and Tx clean flow. In the Tx clean flow we
calculate the bytecount (called total_bytes) as we clean the
descriptors so the value used in the Tx clean path is correct. Fix this
by using += in ice_tso instead of =. This fixes the mismatch in
bytecount mentioned above.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Prior to this commit the driver was running into tx_timeouts when a
queue was stressed enough. This was happening because the HW tail
and SW tail (NTU) were incorrectly out of sync. Consequently this was
causing the HW head to collide with the HW tail, which to the hardware
means that all descriptors posted for Tx have been processed.

Due to the Tx logic used in the driver SW tail and HW tail are allowed
to be out of sync. This is done as an optimization because it allows the
driver to write HW tail as infrequently as possible, while still
updating the SW tail index to keep track. However, there are situations
where this results in the tail never getting updated, resulting in Tx
timeouts.

Tx HW tail write condition:
	if (netif_xmit_stopped(txring_txq(tx_ring) || !skb->xmit_more)
		writel(sw_tail, tx_ring->tail);

An issue was found in the Tx logic that was causing the afore mentioned
condition for updating HW tail to never happen, causing tx_timeouts.

In ice_xmit_frame_ring we calculate how many descriptors we need for the
Tx transaction based on the skb the kernel hands us. This is then passed
into ice_maybe_stop_tx along with some extra padding to determine if we
have enough descriptors available for this transaction. If we don't then
we return -EBUSY to the stack, otherwise we move on and eventually
prepare the Tx descriptors accordingly in ice_tx_map and set
next_to_watch. In ice_tx_map we make another call to ice_maybe_stop_tx
with a value of MAX_SKB_FRAGS + 4. The key here is that this value is
possibly less than the value we sent in the first call to
ice_maybe_stop_tx in ice_xmit_frame_ring. Now, if the number of unused
descriptors is between MAX_SKB_FRAGS + 4 and the value used in the first
call to ice_maybe_stop_tx in ice_xmit_frame_ring then we do not update
the HW tail because of the "Tx HW tail write condition" above. This is
because in ice_maybe_stop_tx we return success from ice_maybe_stop_tx
instead of calling __ice_maybe_stop_tx and subsequently calling
netif_stop_subqueue, which sets the __QUEUE_STATE_DEV_XOFF bit. This
bit is then checked in the "Tx HW tail write condition" by calling
netif_xmit_stopped and subsequently updating HW tail if the
afore mentioned bit is set.

In ice_clean_tx_irq, if next_to_watch is not NULL, we end up cleaning
the descriptors that HW sets the DD bit on and we have the budget. The
HW head will eventually run into the HW tail in response to the
description in the paragraph above.

The next time through ice_xmit_frame_ring we make the initial call to
ice_maybe_stop_tx with another skb from the stack. This time we do not
have enough descriptors available and we return NETDEV_TX_BUSY to the
stack and end up setting next_to_watch to NULL.

This is where we are stuck. In ice_clean_tx_irq we never clean anything
because next_to_watch is always NULL and in ice_xmit_frame_ring we never
update HW tail because we already return NETDEV_TX_BUSY to the stack and
eventually we hit a tx_timeout.

This issue was fixed by making sure that the second call to
ice_maybe_stop_tx in ice_tx_map is passed a value that is >= the value
that was used on the initial call to ice_maybe_stop_tx in
ice_xmit_frame_ring. This was done by adding the following defines to
make the logic more clear and to reduce the chance of mucking this up
again:

ICE_CACHE_LINE_BYTES		64
ICE_DESCS_PER_CACHE_LINE	(ICE_CACHE_LINE_BYTES / \
				 sizeof(struct ice_tx_desc))
ICE_DESCS_FOR_CTX_DESC		1
ICE_DESCS_FOR_SKB_DATA_PTR	1

The ICE_CACHE_LINE_BYTES being 64 is an assumption being made so we
don't have to figure this out on every pass through the Tx path. Instead
I added a sanity check in ice_probe to verify cache line size and print
a message if it's not 64 Bytes. This will make it easier to file issues
if they are seen when the cache line size is not 64 Bytes when reading
from the GLPCI_CNF2 register.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In the remove path, the vsi->netdev is being set to NULL before the call
to free vectors. This is causing the netif_napi_del call to never be made.

Add a call to ice_napi_del to the same location as the calls to
unregister_netdev and just prior to them. This will use the reverse flow
as the register and netif_napi_add calls.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Print should say "Enabling" instead of "Enaabling"
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

According to the spec, whenever insert PVID field is set, the VLAN
driver insertion mode should be set to 01b which isn't done currently.
Fix it.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_restore_vlan and active_vlans were originally put in place to
reprogram VLAN filters in the replay path. This is now done as part
of the much broader VSI rebuild/replay framework. So remove both
ice_restore_vlan and active_vlans
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In the unload path, all VSIs are freed. Also free the related VSI
contexts to prevent memory leaks.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Setting Rx or Tx pause parameter currently results in link loss on the
interface, requiring the platform/host to be cold power cycled. Fix it.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The remove path does not currently check to see if a
reset is in progress before proceeding.  This can cause
a resource collision resulting in various types of errors.

Check for reset in progress and wait for a reasonable
amount of time before allowing the remove to progress.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Set the carrier state post rebuild by querying the link status. Also
start/stop queues based on link status.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch allows users to enable/disable internal TX and/or RX clock
delay for BCM54616S PHYs so as to satisfy RGMII timing specifications.

On a particular platform, whether TX and/or RX clock delay is required
depends on how PHY connected to the MAC IP. This requirement can be
specified through "phy-mode" property in the platform device tree.

The patch is inspired by commit 73333626 ("net: phy: Allow BCM5481x
PHYs to setup internal TX/RX clock delay").
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull tracing fix from Steven Rostedt:
 "Masami found a slight bug in his code where he transposed the
  arguments of a call to strpbrk.

  The reason this wasn't detected in our tests is that the only way this
  would transpire is when a kprobe event with a symbol offset is
  attached to a function that belongs to a module that isn't loaded yet.
  When the kprobe trace event is added, the offset would be truncated
  after it was parsed, and when the module is loaded, it would use the
  symbol without the offset (as the nul character added by the parsing
  would not be replaced with the original character)"

* tag 'trace-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing/kprobes: Fix strpbrk() argument order

Pull ARM fix from Russell King:
 "Ard spotted a typo in one of the assembly files which leads to a
  kernel oops when that code path is executed. Fix this"

* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8809/1: proc-v7: fix Thumb annotation of cpu_v7_hvc_switch_mm

Pull networking fixes from David Miller:

 1) Handle errors mid-stream of an all dump, from Alexey Kodanev.

 2) Fix build of openvswitch with certain combinations of netfilter
    options, from Arnd Bergmann.

 3) Fix interactions between GSO and BQL, from Eric Dumazet.

 4) Don't put a '/' in RTL8201F's sysfs file name, from Holger
    Hoffstätte.

 5) S390 qeth driver fixes from Julian Wiedmann.

 6) Allow ipv6 link local addresses for netconsole when both source and
    destination are link local, from Matwey V. Kornilov.

 7) Fix the BPF program address seen in /proc/kallsyms, from Song Liu.

 8) Initialize mutex before use in dsa microchip driver, from Tristram
    Ha.

 9) Out-of-bounds access in hns3, from Yunsheng Lin.

10) Various netfilter fixes from Stefano Brivio, Jozsef Kadlecsik, Jiri
    Slaby, Florian Westphal, Eric Westbrook, Andrey Ryabinin, and Pablo
    Neira Ayuso.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (50 commits)
  net: alx: make alx_drv_name static
  net: bpfilter: fix iptables failure if bpfilter_umh is disabled
  sock_diag: fix autoloading of the raw_diag module
  net: core: netpoll: Enable netconsole IPv6 link local address
  ipv6: properly check return value in inet6_dump_all()
  rtnetlink: restore handling of dumpit return value in rtnl_dump_all()
  net/ipv6: Move anycast init/cleanup functions out of CONFIG_PROC_FS
  bonding/802.3ad: fix link_failure_count tracking
  net: phy: realtek: fix RTL8201F sysfs name
  sctp: define SCTP_SS_DEFAULT for Stream schedulers
  sctp: fix strchange_flags name for Stream Change Event
  mlxsw: spectrum: Fix IP2ME CPU policer configuration
  openvswitch: fix linking without CONFIG_NF_CONNTRACK_LABELS
  qed: fix link config error handling
  net: hns3: Fix for out-of-bounds access when setting pfc back pressure
  net/mlx4_en: use __netdev_tx_sent_queue()
  net: do not abort bulk send on BQL status
  net: bql: add __netdev_tx_sent_queue()
  s390/qeth: report 25Gbit link speed
  s390/qeth: sanitize ARP requests
  ...

Due to what appears to be a copy/paste error, the opening ENTRY()
of cpu_v7_hvc_switch_mm() lacks a matching ENDPROC(), and instead,
the one for cpu_v7_smc_switch_mm() is duplicated.

Given that it is ENDPROC() that emits the Thumb annotation, the
cpu_v7_hvc_switch_mm() routine will be called in ARM mode on a
Thumb2 kernel, resulting in the following splat:

  Internal error: Oops - undefined instruction: 0 [#1] SMP THUMB2
  Modules linked in:
  CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.18.0-rc1-00030-g4d28ad89189d-dirty #488
  Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
  PC is at cpu_v7_hvc_switch_mm+0x12/0x18
  LR is at flush_old_exec+0x31b/0x570
  pc : [<c0316efe>]    lr : [<c04117c7>]    psr: 00000013
  sp : ee899e50  ip : 00000000  fp : 00000001
  r10: eda28f34  r9 : eda31800  r8 : c12470e0
  r7 : eda1fc00  r6 : eda53000  r5 : 00000000  r4 : ee88c000
  r3 : c0316eec  r2 : 00000001  r1 : eda53000  r0 : 6da6c000
  Flags: nzcv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none

Note the 'ISA ARM' in the last line.

Fix this by using the correct name in ENDPROC().

Cc: <stable@vger.kernel.org>
Fixes: 10115105 ("ARM: spectre-v2: add firmware based hardening")
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains the first batch of Netfilter fixes for
your net tree:

1) Fix splat with IPv6 defragmenting locally generated fragments,
   from Florian Westphal.

2) Fix Incorrect check for missing attribute in nft_osf.

3) Missing INT_MIN & INT_MAX definition for netfilter bridge uapi
   header, from Jiri Slaby.

4) Revert map lookup in nft_numgen, this is already possible with
   the existing infrastructure without this extension.

5) Fix wrong listing of set reference counter, make counter
   synchronous again, from Stefano Brivio.

6) Fix CIDR 0 in hash:net,port,net, from Eric Westbrook.

7) Fix allocation failure with large set, use kvcalloc().
   From Andrey Ryabinin.

8) No need to disable BH when fetch ip set comment, patch from
   Jozsef Kadlecsik.

9) Sanity check for valid sysfs entry in xt_IDLETIMER, from
   Taehee Yoo.

10) Fix suspicious rcu usage via ip_set() macro at netlink dump,
    from Jozsef Kadlecsik.

11) Fix setting default timeout via nfnetlink_cttimeout, this
    comes with preparation patch to add nf_{tcp,udp,...}_pernet()
    helper.

12) Allow ebtables table nat to be of filter type via nft_compat.
    From Florian Westphal.

13) Incorrect calculation of next bucket in early_drop, do no bump
    hash value, update bucket counter instead. From Vasily Khoruzhick.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

alx_drv_name is not used outside main.c, so there's no reason for it to
have external linkage.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

When iptables command is executed, ip_{set/get}sockopt() try to upload
bpfilter.ko if bpfilter is enabled. if it couldn't find bpfilter.ko,
command is failed.
bpfilter.ko is generated if CONFIG_BPFILTER_UMH is enabled.
ip_{set/get}sockopt() only checks CONFIG_BPFILTER.
So that if CONFIG_BPFILTER is enabled and CONFIG_BPFILTER_UMH is disabled,
iptables command is always failed.

test config:
   CONFIG_BPFILTER=y
   # CONFIG_BPFILTER_UMH is not set

test command:
   %iptables -L
   iptables: No chain/target/match by that name.

Fixes: d2ba09c1 ("net: add skeleton of bpfilter kernel module")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPPROTO_RAW isn't registred as an inet protocol, so
inet_protos[protocol] is always NULL for it.

Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Xin Long <lucien.xin@gmail.com>
Fixes: bf2ae2e4 ("sock_diag: request _diag module only when the family or proto has been registered")
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no reason to discard using source link local address when
remote netconsole IPv6 address is set to be link local one.

The patch allows administrators to use IPv6 netconsole without
explicitly configuring source address:

    netconsole=@/,@fe80::5054:ff:fe2f:6012/
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure we call fib6_dump_end() if it happens that skb->len
is zero. rtnl_dump_all() can reset cb->args on the next loop
iteration there.

Fixes: 08e814c9 ("net/ipv6: Bail early if user only wants cloned entries")
Fixes: ae677bbb ("net: Don't return invalid table id error when dumping all families")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For non-zero return from dumpit() we should break the loop
in rtnl_dump_all() and return the result. Otherwise, e.g.,
we could get the memory leak in inet6_dump_fib() [1]. The
pointer to the allocated struct fib6_walker there (saved
in cb->args) can be lost, reset on the next iteration.

Fix it by partially restoring the previous behavior before
commit c63586dc ("net: rtnl_dump_all needs to propagate
error from dumpit function"). The returned error from
dumpit() is still passed further.

[1]:
unreferenced object 0xffff88001322a200 (size 96):
  comm "sshd", pid 1484, jiffies 4296032768 (age 1432.542s)
  hex dump (first 32 bytes):
    00 01 00 00 00 00 ad de 00 02 00 00 00 00 ad de  ................
    18 09 41 36 00 88 ff ff 18 09 41 36 00 88 ff ff  ..A6......A6....
  backtrace:
    [<0000000095846b39>] kmem_cache_alloc_trace+0x151/0x220
    [<000000007d12709f>] inet6_dump_fib+0x68d/0x940
    [<000000002775a316>] rtnl_dump_all+0x1d9/0x2d0
    [<00000000d7cd302b>] netlink_dump+0x945/0x11a0
    [<000000002f43485f>] __netlink_dump_start+0x55d/0x800
    [<00000000f76bbeec>] rtnetlink_rcv_msg+0x4fa/0xa00
    [<000000009b5761f3>] netlink_rcv_skb+0x29c/0x420
    [<0000000087a1dae1>] rtnetlink_rcv+0x15/0x20
    [<00000000691b703b>] netlink_unicast+0x4e3/0x6c0
    [<00000000b5be0204>] netlink_sendmsg+0x7f2/0xba0
    [<0000000096d2aa60>] sock_sendmsg+0xba/0xf0
    [<000000008c1b786f>] __sys_sendto+0x1e4/0x330
    [<0000000019587b3f>] __x64_sys_sendto+0xe1/0x1a0
    [<00000000071f4d56>] do_syscall_64+0x9f/0x300
    [<000000002737577f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
    [<0000000057587684>] 0xffffffffffffffff

Fixes: c63586dc ("net: rtnl_dump_all needs to propagate error from dumpit function")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the anycast.c init and cleanup functions which were inadvertently
added inside the CONFIG_PROC_FS definition.

Fixes: 2384d025 ("net/ipv6: Add anycast addresses to a global hashtable")
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The __no_sanitize_address_or_inline and __no_kasan_or_inline defines
are almost identical. The only difference is that __no_kasan_or_inline
does not have the 'notrace' attribute.

To be able to replace __no_sanitize_address_or_inline with the older
definition, add 'notrace' to __no_kasan_or_inline and change to two
users of __no_sanitize_address_or_inline in the s390 code.

The 'notrace' option is necessary for e.g. the __load_psw_mask function
in arch/s390/include/asm/processor.h. Without the option it is possible
to trace __load_psw_mask which leads to kernel stack overflow.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pointed-out-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix strpbrk()'s argument order, it must pass acceptable string
in 2nd argument. Note that this can cause a kernel panic where
it recovers backup character to code->data.

Link: http://lkml.kernel.org/r/154108256792.2604.1816052586385217811.stgit@devbox

Fixes: a6682814 ("tracing/kprobes: Allow kprobe-events to record module symbol")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

Commit 4d2c0cda set slave->link to
BOND_LINK_DOWN for 802.3ad bonds whenever invalid speed/duplex values
were read, to fix a problem with slaves getting into weird states, but
in the process, broke tracking of link failures, as going straight to
BOND_LINK_DOWN when a link is indeed down (cable pulled, switch rebooted)
means we broke out of bond_miimon_inspect()'s BOND_LINK_DOWN case because
!link_state was already true, we never incremented commit, and never got
a chance to call bond_miimon_commit(), where slave->link_failure_count
would be incremented. I believe the simple fix here is to mark the slave
as BOND_LINK_FAIL, and let bond_miimon_inspect() transition the link from
_FAIL to either _UP or _DOWN, and in the latter case, we now get proper
incrementing of link_failure_count again.

Fixes: 4d2c0cda ("bonding: speed/duplex update at NETDEV_UP event")
CC: Mahesh Bandewar <maheshb@google.com>
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:

$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]

Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd ("net: phy: realtek: add RTL8201F phy-id and functions").

Fix this by removing the offending slash in the driver name.

Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.

Fixes: 513588dd ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull UBIFS updates from Richard Weinberger:

 - Full filesystem authentication feature, UBIFS is now able to have the
   whole filesystem structure authenticated plus user data encrypted and
   authenticated.

 - Minor cleanups

* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
  ubifs: Remove unneeded semicolon
  Documentation: ubifs: Add authentication whitepaper
  ubifs: Enable authentication support
  ubifs: Do not update inode size in-place in authenticated mode
  ubifs: Add hashes and HMACs to default filesystem
  ubifs: authentication: Authenticate super block node
  ubifs: Create hash for default LPT
  ubfis: authentication: Authenticate master node
  ubifs: authentication: Authenticate LPT
  ubifs: Authenticate replayed journal
  ubifs: Add auth nodes to garbage collector journal head
  ubifs: Add authentication nodes to journal
  ubifs: authentication: Add hashes to index nodes
  ubifs: Add hashes to the tree node cache
  ubifs: Create functions to embed a HMAC in a node
  ubifs: Add helper functions for authentication support
  ubifs: Add separate functions to init/crc a node
  ubifs: Format changes for authentication support
  ubifs: Store read superblock node
  ubifs: Drop write_node
  ...

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Bugfix:
   - Fix build issues on architectures that don't provide 64-bit cmpxchg

  Cleanups:
   - Fix a spelling mistake"

* tag 'nfs-for-4.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS: fix spelling mistake, EACCESS -> EACCES
  SUNRPC: Use atomic(64)_t for seq_send(64)

Pull more timer updates from Thomas Gleixner:
 "A set of commits for the new C-SKY architecture timers"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  dt-bindings: timer: gx6605s SOC timer
  clocksource/drivers/c-sky: Add gx6605s SOC system timer
  dt-bindings: timer: C-SKY Multi-processor timer
  clocksource/drivers/c-sky: Add C-SKY SMP timer

Pull NTB updates from Jon Mason:
 "Fairly minor changes and bug fixes:

  NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
  private struct, and a few bug fixes"

* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
  ntb: idt: Alter the driver info comments
  ntb: idt: Discard temperature sensor IRQ handler
  ntb: idt: Add basic hwmon sysfs interface
  ntb: idt: Alter temperature read method
  ntb_netdev: Simplify remove with client device drvdata
  NTB: transport: Try harder to alloc an aligned MW buffer
  ntb: ntb_transport: Mark expected switch fall-throughs
  ntb: idt: Set PCIe bus address to BARLIMITx
  NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
  ntb: intel: fix return value for ndev_vec_mask()
  ntb_netdev: fix sleep time mismatch

According to rfc8260#section-4.3.2, SCTP_SS_DEFAULT is required to
defined as SCTP_SS_FCFS or SCTP_SS_RR.

SCTP_SS_FCFS is used for SCTP_SS_DEFAULT's value in this patch.

Fixes: 5bbbbe32 ("sctp: introduce stream scheduler foundations")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As defined in rfc6525#section-6.1.3, SCTP_STREAM_CHANGE_DENIED
and SCTP_STREAM_CHANGE_FAILED should be used instead of
SCTP_ASSOC_CHANGE_DENIED and SCTP_ASSOC_CHANGE_FAILED.

To keep the compatibility, fix it by adding two macros.

Fixes: b444153f ("sctp: add support for generating add stream change event notification")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-11-03

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix BPF prog kallsyms and bpf_prog_get_info_by_fd() jited address export
   to not use page start but actual start instead to work correctly with
   profiling e.g. finding hot instructions from stack traces. Also fix latter
   with regards to dumping address and jited len for !multi prog, from Song.

2) Fix bpf_prog_get_info_by_fd() for !root to zero info.nr_jited_func_lens
   instead of leaving the user provided length, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.

Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.

Fixes: 9148e7cf ("mlxsw: spectrum: Add policers for trap groups")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_CC_OPTIMIZE_FOR_DEBUGGING is enabled, the compiler
fails to optimize out a dead code path, which leads to a link failure:

net/openvswitch/conntrack.o: In function `ovs_ct_set_labels':
conntrack.c:(.text+0x2e60): undefined reference to `nf_connlabels_replace'

In this configuration, we can take a shortcut, and completely
remove the contrack label code. This may also help the regular
optimization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

gcc-8 notices that qed_mcp_get_transceiver_data() may fail to
return a result to the caller:

drivers/net/ethernet/qlogic/qed/qed_mcp.c: In function 'qed_mcp_trans_speed_mask':
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1955:2: error: 'transceiver_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]

When an error is returned by qed_mcp_get_transceiver_data(), we
should propagate that to the caller of qed_mcp_trans_speed_mask()
rather than continuing with uninitialized data.

Fixes: c56a8be7 ("qed: Add supported link and advertise link to display in ethtool.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>