We can split validation into three parts: getting voltage level, getting
watermarks, and rq/dlg calculations. The voltage level is enough to answer
the question "do we support this state", and the rest of it is to determine
what hardware programming is needed to support the state. Most of the calls
to validate_bandwidth only care about the first part, so we added an early
return in that case
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]

display_mode_vba is for DCN2 and up. When building for upstream (DCN1
enabled only), there will be a build error, since display_mode_vba.c/h
is stripped out.

Note that building DCN1 only with internal dal-dev is still fine, since
display_mode_vba.h is not stripped out internally - only in upstream.
The make directives therefore stll work, and so will any #include's.

[How]

Since subsequent generations require DCN2 enabled anyways, guard the
makefile directive for display_mode_vba.o with DCN2. Guard any includes
with DCN2. In addition, guard the entire contents of display_mode_vba.h
with DCN2, to simulate the file being stripped out in upstream.

A forward declaration for 'struct display_mode_lib' also needs to be
added in display_mode_lib.h. Previously, display_mode_vba.h contained
the forward declaration, and display_mode_lib.h in turn included it.
This won't work if mode_vba.h is stripped out, requring mode_lib.h to do
so itself.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Usage of this enum is DSC-only.

[How]
Guard it with CONFIG_DRM_AMD_DC_DSC_SUPPORT.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why & How]
The follow up change
Improve some naming for fields and structs
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Can not turn on two displays at the same time with the asic having only one DSC.
DC_DSC_RESOURCE allocation failed.

[Solution]
Only add_dsc if the timing is dsc capable based on diag_dc and num_dsc
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
If voltage level > 0, DCFCLK and SOCCLK could be 0 during DML
calculations, which ended up causing an assert.

[How]
Initialize dcfclk_mhz and socclk_mhz values according to the
voltage level.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Added some regs and exposed some functions for future use
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Move flags from color_gamma.h to mod_shared.h
and add more options and setting structures
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why] DSC spec requires this
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
On at least some of the devices (e.g. Realtek scaler) we get a black screen if 1/16th
precision is used.

[how]
Work around it by reducing precision to 1/8th for N4:2:2 and 4:2:0 color formats. This
is a safe workaround and would have a very mild impact on the quality.
The issue is still to be root-caused and fixed correctly.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
Global optic double buffer lock is currently disabled due to
incorrect programming sequence that affects non global lock.

[how]
Isolate global lock programming sequence out of non global lock
programming sequence, so it can be enabled without affecting
non global lock.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
This is now done in the original link bandwidth calculation and DSC
must not do this anymore.

[how]
Remove the line of code that should have been removed when transition
to correctly applying FEC overhead was made.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

code restructure.
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We shouldnt need overhead on top of dppclk when setting fclk.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Remove dc_dsc hack for MST policy
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
Clean up some dsc legacy functions that are
no longer needed.

[how]
remove two dsc functions in dc_dsc, use dc_bandwidth_in_kbps_from_timing
instead of calc_required_bandwidth_for_timing.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
dcn20_apply_ctx_for_surface can be called with 0 planes, which means we
should blank the display. In this case when we get down to
dcn20_setup_gsl_group_as_lock, pipe_ctx->plane_state is NULL, but we don't
check for it. However, this function is only called by
dcn20_pipe_control_lock, and in that function we alraedy have a local for
the immediate flip status, which is what we care about in the plane state.

[How]
 - pass in immediate flip status as parameter
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Currently dsc is validated not taking the image width limitation into
mind.

This change addresses that, but due to previous design being limited
to non odm dsc validation additional sequence changes are made.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
u clk set request was being sent in units of mts, when it needed to be
in units of Mhz

[How]
add a division by 16 to convert from mts to Mhz
Signed-off-by: Aidan Wood <Aidan.Wood@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
If num_states == 0 we did update_bound_box which doesn't updated any max
clocks if num_states == 0, therefore we need to do cap_soc_clocks
instead, also SMU cannot set DCF clock to a higher than or equal to freq
than SOC clock

[How]
Add a num_states != 0 check for update_bounding_box to be run, and after
we run get_maximum_sustainable_clocks we now check if the reported max
value of DCF is higher than SOC and if necessary set it to 1000
(becomes 1 after division by 1000) lower than SOC
Signed-off-by: Aidan Wood <Aidan.Wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
Currently link bandwidth is calculated in various places using the same
multi-step formula. Doing this in one common place makes sure the same
formula will indeed be applied to all link bandwidth calculations.
It also makes it possible to apply link-setting-specific adjustments
that affect effective link bandwidth.

[how]
Replace all implementations of link bandwidth calculation with a call
to a function.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why & How]
When TM is enabled with 3dlut, we apply conversion to
dcip3 in gamut remap matrix, if source area less than
dcip3. If it is bigger, we remap to bt2020. The added
flags will be used to facilitate this logic.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Currently dcn2+ validation will unconditionally print a failure
reason before validation completes. This change categorizes the
failure reason as a warning log and only prints at the end of
validation resolving false positives.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Description]
swath_bytes_horz_wc should be 256/64/64 for 2160p 32bpp surface
Signed-off-by: Bob Yang <Bob.Yang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]

dcn*_disable_plane() doesn't unlock the pipe anymore, making the extra
lock unnecessary.

In addition - during full plane updates - all necessary pipes should be
locked/unlocked together when modifying hubp to avoid tearing in
pipesplit setups.

[How]

Remove redundant locks, and add function to lock all pipes. If an
interdependent pipe update is required, lock down all pipes. Otherwise,
lock only the top pipe for the updated pipe tree.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

A previous fix was done for DCN1 that needed to be ported to DCN2:
commit 60c677534e73 ("drm/amd/display: Disconnect mpcc when changing tg")
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable DSC (display stream compression) by default.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

not needed for bring up.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why] we meet a bug when program dsc register even dsc mode is not
enabled. disable dsc config for now. we will re-visit this issue.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[todo] need find caller bug. tempooariy fix
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY] dcn20 enable usb-c dp ALT mode in dmcu. There is bug
when enable abm feature which cause system crash. dal team
will debug this bug later.

[HOW] disable dcn abm feature for dcn20.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

* Pull duplicate audio_clock_info struct to stream_encoder.h
* Generalize sec_gsp7* to sec_gsp_pps*
* Expose enc1 and enc2 stream encoder audio funcs
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
pstate allow/block is not being handled properly on DCN2

[how]
DML needs to be updated to calculate pstate support at both min and max
mpc combine rather than just min
clock manager needs to update current to new pstate support before
sending to pplib/smu
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Adding writeback_config enum to vba_vars_st, replacing old flag.
Initialize to dm_normal.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Some HW specific implementations can be pulled out into clk_mgr.c.

[How]
- Pull get_active_display_cnt out to clk_mgr.
- Pull out shared logic in set_dispclk and set_dprefclk
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Description]
DMUB is using DPREF CLK, but DMCU still use displayclk.
This is for updating DMCU wait_for_loop after display clock change.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Modern Standby may toggle display adapter state between D0
and D3 state unpredictably.
But events that cause transition to D0 are not always resulting
in a display light up scenario.

Modern eDP panels should be able to power on panel logic
quickly upon VDD going high. Based on spec, the T3 time
between VDD on and HPD high can be between 0 and 80 ms.

Doing any tricky sorts of optimization by powering on panel
VDD early during D0 transition on can negatively impact other
features due to unnecessary power drain and toggling when
final system state does not intend for the panel to be lit up.

We need OEMs to source higher end panels that have T3 time
close to 0 if they want quick S3/Modern Standby resume times.

[How]
Remove panel VDD power on in init_hw
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
link-specific functions should reside in dc_link.c

[How]
Move them there.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
Current calculation of bounding box will cause DML to increase voltage
state due to DPP or DISPCLK, this is unnecessary since from DML perspective
we can max DPP/DISP can be supported at DPM0.  This is because
increasing voltage for DPP/DISP is done separately via actual minimum values
of DISP and DPP CLK

[how]
For each calculated state, DPP, DISP, PHY, and DSC clk should always be set to
maximum.  FCLK, SOCCLK, and DCFCLK should be based of UCLK.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
1. DMCU is not running on some platform but driver still send ABM
   command. It may cause assert due to DMCU is not alive.
2. To make sure PSR disable when driver disable

[How]
1. Add dmcu_is_running in ABM struct, driver can check this flag to
   determine driver should send ABM command or not.
2. Send PSR disable command when destroy PSR
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>