1. QPIC NAND controller uses 3 BAM channels: command, data tx
   and data rx while EBI2 NAND controller uses only single ADM
   channel.
2. CRCI is only required for ADM DMA and it's not required for
   BAM DMA.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

The current driver only supports EBI2 NAND controller which uses
ADM DMA. The latest QCOM SoC uses QPIC NAND controller with BAM
DMA. NAND registers and programming sequence are same for EBI2
and QPIC NAND so the same driver can support QPIC NAND also by
adding the BAM DMA support. This patch adds the is_bam in NAND
property which will be checked for determining the DMA engine type.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

Currently driver data is being assigned directly with ECC modes.
Now, the plan is to add more NAND controller versions which will
have different properties. This patch reorganizes the current driver
data assignment by creating NAND controller properties structure
which will contain all properties specific to NAND controller.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

The NAND page read fails without complete boot chain since
NAND_DEV_CMD_VLD value is not proper. The default power on reset
value for this register is

    0xe - ERASE_START_VALID | WRITE_START_VALID | READ_STOP_VALID

The READ_START_VALID should be enabled for sending PAGE_READ
command. READ_STOP_VALID should be cleared since normal NAND
page read does not require READ_STOP command.

Fixes: c76b78d8 ("mtd: nand: Qualcomm NAND controller driver")
Cc: stable@vger.kernel.org
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

platform_get_irq() returns an error code, but the mtk_ecc driver
ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.

Print and propagate the return value of platform_get_irq on failure.

This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

platform_get_irq() returns an error code, but the sh_flctl
driver ignores it and always returns -ENXIO. This is not correct
and, prevents -EPROBE_DEFER from being propagated properly.

Print and propagate the return value of platform_get_irq on failure.

This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

The return value of dma_map_single() should be checked by
dma_mapping_error(). However, in function flctl_dma_fifo0_transfer(), its
return value is checked against NULL, which could result in failures.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

of_irq_get() may return 0 as well as negative error number on failure,
while the driver only checks for the negative values. The driver would
then call devm_request_irq() for IRQ0  in its probe method and never get
a valid interrupt.

Check for 'nc->irq <= 0' instead and return -ENXIO from the driver's probe
if of_irq_get() returned 0.

Fixes: f88fc122 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Wenyou Yang <Wenyou.yang@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

According to the datasheet of the H27UCG8T2BTR the NAND Technology field
(6th byte of the "Device Identifier Description", bits 0-2) the
following values are possible:
- 0x0 = 48nm
- 0x1 = 41nm
- 0x2 = 32nm
- 0x3 = 26nm
- 0x4 = 20nm
- (all others are reserved)

Fix this by extending the mask for this field to allow detecting value
0x4 (20nm) as valid NAND technology.
Without this the detection of the ECC requirements fails, because the
code assumes that the device is a 48nm device (0x4 & 0x3 = 0x0) and
aborts with "Invalid ECC requirements" because it cannot map the "ECC
Level". Extending the mask makes the ECC requirement detection code
recognize this chip as <= 26nm and sets up the ECC step size and ECC
strength correctly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes: 78f3482d ("mtd: nand: hynix: Rework NAND ID decoding to extract more information")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

Commit a894cf6c ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
introduced a bug in the OOB layout description. Even if the driver claims
that 3 ECC bytes are reserved to protect 512 bytes of data, it's actually
5 ECC bytes to protect 512+6 bytes of data (some OOB bytes are also
protected using extra ECC bytes).

Fix the mxc_v1_ooblayout_{free,ecc}() functions to reflect this behavior.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: a894cf6c ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

Commit a53e35db ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.

No functional changes.

Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

- clk_prepare_enable() can fail here and we must check its return value.
 - stfsm_probe() can fail here and we must disable clock.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

- clk_prepare_enable() can fail here and we must check its return value.
 - oxnas_nand_probe() can fail here and we must disable clock.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

orion_nand_read_buf uses an inline assembly with the "ldrd"
instruction, which is only available from ARMv5 upwards. This
used to be fine, since all users have an ARMv5 or ARMv7 CPU,
but now we can also build a multiplatform kernel with ARMv4
support enabled in addition to the "kirkwood" (mvebu) platform.

This provides an alternative to call the readsl() function that
is supposed to have the same effect and is also optimized for
performance.

I first posted a version of this patch back in 2014, and there
was some discussion about it then. This fixes the bugs identified
back then and should be a reasonable alternative for the rare
corner case.

Link: https://patchwork.kernel.org/patch/4144791/
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

The controller supported by the pxa3xx_nand driver is also available on
the mvebu 64-bit SoCs, such as the Armada 7K and Armada 8K SoCs. This
patch updates the Kconfig dependency to allow building the kernel for
this SoC family too.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

The NAND controller can support multiple NAND devices having different
page sizes. Future code will require us to allocate memory based on the
maximum number of codewords among all the devices. We reorganize the
NAND device probing such that the ONFI parameters are first read for
each connected device to identify the maximum number of codewords
possible, and only then proceed with MTD device registration (i.e, call
nand_scan_tail and mtd_device_register).

This is a reorganization of the existing code and will not change any
functionality.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

The memset in clear_read_regs is overhead. All the register data
will be filled by DMA during NAND operation so making these
register variables zero is not required.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

Each NAND page consist of multiple codewords. Following is
sequence for NAND page write according to hardware guide.

1. Program Power-up configuration, page row, page column
   address and flash configuration registers.
2. Write NAND_FLASH_CMD followed by NANC_EXEC_CMD for each
   codeword.
3. Read NAND_FLASH_STATUS for each codeword.

The step 1 should be done once for each page and step 2,3 should
be done for each codeword.

Currently, all the 3 steps are being done for each codeword which
is wrong. Now this patch reorganizes page write functions to
configure page specific register once and per codeword specific
registers for each NAND ECC step.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

Each NAND page consist of multiple codewords. Following is
sequence for NAND page read according to hardware guide.

1. Program Power-up configuration, page row, page column
address and flash configuration registers.
2. Write NAND_FLASH_CMD followed by NANC_EXEC_CMD for each
codeword.
3. Read NAND_FLASH_STATUS for each codeword.

The step 1 should be done once for each page and step 2,3 should
be done for each codeword.

Currently, all the 3 steps are being done for each codeword which
is wrong. Now this patch reorganizes read page functions to
configure page specific register once and per codeword specific
registers for each NAND ECC step.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

Currently the compatible “qcom,nandcs” is being used for each
connected NAND device to support for multiple NAND devices in the
same bus. The same thing can be achieved by looking reg property
for each sub nodes which contains the chip select number so this
patch removes the use of “qcom,nandcs” for specifying NAND device
sub nodes.

Since there is no user for this driver currently in so
changing compatible string is safe.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

Currently the compatible “qcom,nandcs” is being used for each
connected NAND device to support for multiple NAND devices in the
same bus. The same thing can be achieved by looking reg property
for each sub nodes which contains the chip select number so this
patch removes the use of “qcom,nandcs” for specifying NAND device
sub nodes.

Since there is no user for this driver currently in so
changing compatible string is safe.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

The configuration for BCH is not correct in the current driver.
The ECC_CFG_ECC_DISABLE bit defines whether to enable or disable the
BCH ECC in which

	0x1 : BCH_DISABLED
	0x0 : BCH_ENABLED

But currently host->bch_enabled is being assigned to BCH_DISABLED.

Fixes: c76b78d8 ("mtd: nand: Qualcomm NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

pinctrl_pm_select_default_state() is already the default pinctrl state and
since pinctrl_pm_select_sleep_state() is not used in this driver, there
is no need to explicitly call pinctrl_pm_select_default_state().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

This commit removes hard-coded '8' used for looping into
struct nand_chip.id.data array.

NAND_MAX_ID_LEN has been introduced by Artem Bityutskiy in
53552d22 for defining ids length in nand_flash_ids[] list.

This commit unifies ids length in nand base driver.
Signed-off-by: Jean-Louis Thekekara <jeanlouis.thekekara@parrot.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

The nand_scan_ident() function is not expected to allocate resources,
and people are usually not calling nand_cleanup() if something fails
between nand_scan_ident() and nand_scan_tail().

Move all functions that may allocate resource to the nand_scan_tail()
path to prevent such resource leaks.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

Commit 7d70f334 ("mtd: nand: add lock/unlock routines") introduced
support for the Micron LOCK/UNLOCK commands but no one ever used the
nand_lock/unlock() functions.

Remove support for these vendor-specific operations from the core. If
one ever wants to add them back they should be put in nand_micron.c and
mtd->_lock/_unlock should be directly assigned from there instead of
exporting the functions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

Pull documentation format standardization from Jonathan Corbet:
 "This series converts a number of top-level documents to the RST format
  without incorporating them into the Sphinx tree. The hope is to bring
  some uniformity to kernel documentation and, perhaps more importantly,
  have our existing docs serve as an example of the desired formatting
  for those that will be added later.

  Mauro has gone through and fixed up a lot of top-level documentation
  files to make them conform to the RST format, but without moving or
  renaming them in any way. This will help when we incorporate the ones
  we want to keep into the Sphinx doctree, but the real purpose is to
  bring a bit of uniformity to our documentation and let the top-level
  docs serve as examples for those writing new ones"

* tag 'standardize-docs' of git://git.lwn.net/linux: (84 commits)
  docs: kprobes.txt: Fix whitespacing
  tee.txt: standardize document format
  cgroup-v2.txt: standardize document format
  dell_rbu.txt: standardize document format
  zorro.txt: standardize document format
  xz.txt: standardize document format
  xillybus.txt: standardize document format
  vfio.txt: standardize document format
  vfio-mediated-device.txt: standardize document format
  unaligned-memory-access.txt: standardize document format
  this_cpu_ops.txt: standardize document format
  svga.txt: standardize document format
  static-keys.txt: standardize document format
  smsc_ece1099.txt: standardize document format
  SM501.txt: standardize document format
  siphash.txt: standardize document format
  sgi-ioc4.txt: standardize document format
  SAK.txt: standardize document format
  rpmsg.txt: standardize document format
  robust-futexes.txt: standardize document format
  ...

Pull random updates from Ted Ts'o:
 "Add wait_for_random_bytes() and get_random_*_wait() functions so that
  callers can more safely get random bytes if they can block until the
  CRNG is initialized.

  Also print a warning if get_random_*() is called before the CRNG is
  initialized. By default, only one single-line warning will be printed
  per boot. If CONFIG_WARN_ALL_UNSEEDED_RANDOM is defined, then a
  warning will be printed for each function which tries to get random
  bytes before the CRNG is initialized. This can get spammy for certain
  architecture types, so it is not enabled by default"

* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: reorder READ_ONCE() in get_random_uXX
  random: suppress spammy warnings about unseeded randomness
  random: warn when kernel uses unseeded randomness
  net/route: use get_random_int for random counter
  net/neighbor: use get_random_u32 for 32-bit hash random
  rhashtable: use get_random_u32 for hash_rnd
  ceph: ensure RNG is seeded before using
  iscsi: ensure RNG is seeded before use
  cifs: use get_random_u32 for 32-bit lock random
  random: add get_random_{bytes,u32,u64,int,long,once}_wait family
  random: add wait_for_random_bytes() API

Pull ->s_options removal from Al Viro:
 "Preparations for fsmount/fsopen stuff (coming next cycle). Everything
  gets moved to explicit ->show_options(), killing ->s_options off +
  some cosmetic bits around fs/namespace.c and friends. Basically, the
  stuff needed to work with fsmount series with minimum of conflicts
  with other work.

  It's not strictly required for this merge window, but it would reduce
  the PITA during the coming cycle, so it would be nice to have those
  bits and pieces out of the way"

* 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  isofs: Fix isofs_show_options()
  VFS: Kill off s_options and helpers
  orangefs: Implement show_options
  9p: Implement show_options
  isofs: Implement show_options
  afs: Implement show_options
  affs: Implement show_options
  befs: Implement show_options
  spufs: Implement show_options
  bpf: Implement show_options
  ramfs: Implement show_options
  pstore: Implement show_options
  omfs: Implement show_options
  hugetlbfs: Implement show_options
  VFS: Don't use save/replace_mount_options if not using generic_show_options
  VFS: Provide empty name qstr
  VFS: Make get_filesystem() return the affected filesystem
  VFS: Clean up whitespace in fs/namespace.c and fs/super.c
  Provide a function to create a NUL-terminated string from unterminated data

Pull more __copy_.._user elimination from Al Viro.

* 'work.__copy_to_user' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  drm_dp_aux_dev: switch to read_iter/write_iter

Pull uacess-unaligned removal from Al Viro:
 "That stuff had just one user, and an exotic one, at that - binfmt_flat
  on arm and m68k"

* 'work.uaccess-unaligned' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  kill {__,}{get,put}_user_unaligned()
  binfmt_flat: flat_{get,put}_addr_from_rp() should be able to fail

Pull network field-by-field copy-in updates from Al Viro:
 "This part of the misc compat queue was held back for review from
  networking folks and since davem has jus ACKed those..."

* 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  get_compat_bpf_fprog(): don't copyin field-by-field
  get_compat_msghdr(): get rid of field-by-field copyin
  copy_msghdr_from_user(): get rid of field-by-field copyin

Pull MIPS updates from Ralf Baechle:
 "Boston platform support:
   - Document DT bindings
   - Add CLK driver for board clocks

  CM:
   - Avoid per-core locking with CM3 & higher
   - WARN on attempt to lock invalid VP, not BUG

  CPS:
   - Select CONFIG_SYS_SUPPORTS_SCHED_SMT for MIPSr6
   - Prevent multi-core with dcache aliasing
   - Handle cores not powering down more gracefully
   - Handle spurious VP starts more gracefully

  DSP:
   - Add lwx & lhx missaligned access support

  eBPF:
   - Add MIPS support along with many supporting change to add the
     required infrastructure

  Generic arch code:
   - Misc sysmips MIPS_ATOMIC_SET fixes
   - Drop duplicate HAVE_SYSCALL_TRACEPOINTS
   - Negate error syscall return in trace
   - Correct forced syscall errors
   - Traced negative syscalls should return -ENOSYS
   - Allow samples/bpf/tracex5 to access syscall arguments for sane
     traces
   - Cleanup from old Kconfig options in defconfigs
   - Fix PREF instruction usage by memcpy for MIPS R6
   - Fix various special cases in the FPU eulation
   - Fix some special cases in MIPS16e2 support
   - Fix MIPS I ISA /proc/cpuinfo reporting
   - Sort MIPS Kconfig alphabetically
   - Fix minimum alignment requirement of IRQ stack as required by
     ABI / GCC
   - Fix special cases in the module loader
   - Perform post-DMA cache flushes on systems with MAARs
   - Probe the I6500 CPU
   - Cleanup cmpxchg and add support for 1 and 2 byte operations
   - Use queued read/write locks (qrwlock)
   - Use queued spinlocks (qspinlock)
   - Add CPU shared FTLB feature detection
   - Handle tlbex-tlbp race condition
   - Allow storing pgd in C0_CONTEXT for MIPSr6
   - Use current_cpu_type() in m4kc_tlbp_war()
   - Support Boston in the generic kernel

  Generic platform:
   - yamon-dt: Pull YAMON DT shim code out of SEAD-3 board
   - yamon-dt: Support > 256MB of RAM
   - yamon-dt: Use serial* rather than uart* aliases
   - Abstract FDT fixup application
   - Set RTC_ALWAYS_BCD to 0
   - Add a MAINTAINERS entry

  core kernel:
   - qspinlock.c: include linux/prefetch.h

  Loongson 3:
   - Add support

  Perf:
   - Add I6500 support

  SEAD-3:
   - Remove GIC timer from DT
   - Set interrupt-parent per-device, not at root node
   - Fix GIC interrupt specifiers

  SMP:
   - Skip IPI setup if we only have a single CPU

  VDSO:
   - Make comment match reality
   - Improvements to time code in VDSO"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (86 commits)
  locking/qspinlock: Include linux/prefetch.h
  MIPS: Fix MIPS I ISA /proc/cpuinfo reporting
  MIPS: Fix minimum alignment requirement of IRQ stack
  MIPS: generic: Support MIPS Boston development boards
  MIPS: DTS: img: Don't attempt to build-in all .dtb files
  clk: boston: Add a driver for MIPS Boston board clocks
  dt-bindings: Document img,boston-clock binding
  MIPS: Traced negative syscalls should return -ENOSYS
  MIPS: Correct forced syscall errors
  MIPS: Negate error syscall return in trace
  MIPS: Drop duplicate HAVE_SYSCALL_TRACEPOINTS select
  MIPS16e2: Provide feature overrides for non-MIPS16 systems
  MIPS: MIPS16e2: Report ASE presence in /proc/cpuinfo
  MIPS: MIPS16e2: Subdecode extended LWSP/SWSP instructions
  MIPS: MIPS16e2: Identify ASE presence
  MIPS: VDSO: Fix a mismatch between comment and preprocessor constant
  MIPS: VDSO: Add implementation of gettimeofday() fallback
  MIPS: VDSO: Add implementation of clock_gettime() fallback
  MIPS: VDSO: Fix conversions in do_monotonic()/do_monotonic_coarse()
  MIPS: Use current_cpu_type() in m4kc_tlbp_war()
  ...

Pull UML updates from Richard Weinberger:
 "Mostly fixes for UML:

   - First round of fixes for PTRACE_GETRESET/SETREGSET

   - A printf vs printk cleanup

   - Minor improvements"

* 'for-linus-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Correctly check for PTRACE_GETRESET/SETREGSET
  um: v2: Use generic NOTES macro
  um: Add kerneldoc for userspace_tramp() and start_userspace()
  um: Add kerneldoc for segv_handler
  um: stub-data.h: remove superfluous include
  um: userspace - be more verbose in ptrace set regs error
  um: add dummy ioremap and iounmap functions
  um: Allow building and running on older hosts
  um: Avoid longjmp/setjmp symbol clashes with libpthread.a
  um: console: Ignore console= option
  um: Use os_warn to print out pre-boot warning/error messages
  um: Add os_warn() for pre-boot warning/error messages
  um: Use os_info for the messages on normal path
  um: Add os_info() for pre-boot information messages
  um: Use printk instead of printf in make_uml_dir

Pull UBIFS updates from Richard Weinberger:

 - Updates and fixes for the file encryption mode

 - Minor improvements

 - Random fixes

* tag 'upstream-4.13-rc1' of git://git.infradead.org/linux-ubifs:
  ubifs: Set double hash cookie also for RENAME_EXCHANGE
  ubifs: Massage assert in ubifs_xattr_set() wrt. init_xattrs
  ubifs: Don't leak kernel memory to the MTD
  ubifs: Change gfp flags in page allocation for bulk read
  ubifs: Fix oops when remounting with no_bulk_read.
  ubifs: Fail commit if TNC is obviously inconsistent
  ubifs: allow userspace to map mounts to volumes
  ubifs: Wire-up statx() support
  ubifs: Remove dead code from ubifs_get_link()
  ubifs: Massage debug prints wrt. fscrypt
  ubifs: Add assert to dent_key_init()
  ubifs: Fix unlink code wrt. double hash lookups
  ubifs: Fix data node size for truncating uncompressed nodes
  ubifs: Don't encrypt special files on creation
  ubifs: Fix memory leak in RENAME_WHITEOUT error path in do_rename
  ubifs: Fix inode data budget in ubifs_mknod
  ubifs: Correctly evict xattr inodes
  ubifs: Unexport ubifs_inode_slab
  ubifs: don't bother checking for encryption key in ->mmap()
  ubifs: require key for truncate(2) of encrypted file