The CLOCK_IN_OMAP4430 clock flag is not currently needed in the OMAP4
ES1 clock tree, and platform discrimination via clock flags is
deprecated in favor of the clkdev mechanism, so, drop it.  (The OMAP4
clock tree autogeneration script has been updated accordingly.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>

The maximum DPLL multiplier (M) values for OMAP2xxx and OMAP3xxx are
one increment higher than they should be.  See for example the
OMAP242x TRM Rev X Section 5.10.6 "Clock Generator Registers" and the
OMAP36xx TRM Rev C Table 3-202 "CM_CLKSEL1_PLL".  Programming a 0 into
the DPLL's M register bitfield is valid for OMAP2/3 and indicates that
the DPLL should enter MN-bypass mode.  Also, increase the minimum
multiplier (M) value for the DPLL rate rounding code from 1 to 2, to
ensure that it does not inadvertently put the DPLL into bypass.

Note that the register documentation in the OMAP2xxx and OMAP3xxx TRMs
does not make clear that the actual DPLL divider value (the "N") is
the content of the appropriate register bitfield for the N value,
_plus one_.  (In other words, an N register bitfield of 0 indicates a
DPLL divider value of 1.)  This is only clearly documented in the
OMAP4430 TRM, in, for example, OMAP4430 TRM Rev A Table 3-1167
"CM_CLKSEL_DPLL_USB".

While here, update copyrights, add kerneldoc for struct dpll_data,
drop the unused struct dpll_data.max_tolerance field, remove some
unnecessary #includes in DPLL-related code, and replace the #include
of <linux/module.h> with <linux/list.h>, which is what was really
needed.  The OMAP4 clock autogenerator script has been updated
accordingly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>

In 3630, DPLL4M2 output can be 96MHz or 192MHz (for SGX to run at
192). This patch has changes to support this feature. 96MHz clock is
generated by dividing 192Mhz clock by 2 using CM_CLKSEL_CORE register.
SGX can select Core Clock, 192MHz clock or CM_96M_FCLK as it's
functional clock. In summary changes done are:
1. Added a feature called omap3_has_192mhz_clk and enabled for 3630
2. Added a new clock node called omap_192m_alwon_ck
3. Made omap_96m_alwon_fck to derive its clock from omap_192m_alwon_ck
Signed-off-by: Vishwanath BS <Vishwanath.bs@ti.com>
[paul@pwsan.com: fixed whitespace]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Divider (M2, M3, M4, M5 and M6) field width has been increased by 1 bit
in 3630. This patch has changes to accommodate this in CM dynamically
based on chip version.
Basically new clock nodes have been added for 3630 DPLL4 M2,M3,M4,M5 and
M6 and value of these nodes are used if cpu type is 3630.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[paul@pwsan.com: updated to apply on 2.6.34 queue; comments added]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

DPLL4 for 3630 introduces a changed block called j type dpll, requiring
special divisor bits and additional reg fields. To allow for silicons to
use this, this is introduced as a flag and is enabled for 3630 silicon.
OMAP4 also has j type dpll for usb.

Tested with 3630 ZOOM3 and OMAP3430 ZOOM2
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vishwanath BS <Vishwanath.bs@ti.com>
[paul@pwsan.com: added some comments; updated copyrights and credits; fixed
 some style issues]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

A check is added for avoiding the sleep/wakeup dependency updates
for OMAP4 as the structures for the dependencies are currently absent.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
[paul@pwsan.com: added warnings, explanatory comment, copyright update]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

This patch implements a workaround for the DPLL HS divider limitation
in OMAP3630 as given by Errata ID: i556.

Errata:
When PWRDN bit is set, it resets the internal HSDIVIDER divide-by value (Mx).
The reset value gets loaded instead of the previous value.
The following HSDIVIDERs exhibit above behavior:
. DPLL4 : M6 / M5 / M4 / M3 / M2 (CM_CLKEN_PLL[31:26] register bits)
. DPLL3 : M3 (CM_CLKEN_PLL[12] register bit).

Work Around:
It is mandatory to apply the following sequence to ensure the write
value will
be loaded in DPLL HSDIVIDER FSM:
The global sequence when using PWRDN bit is the following:
. Disable Mx HSDIVIDER clock output related functional clock enable bits
        (in CM_FCLKEN_xxx / CM_ICLKEN_xxx)
. Enable PWRDN bit of HSDIVIDER
. Disable PWRDN bit of HSDIVIDER
. Read current HSDIVIDER register value
. Write different value in HSDIVIDER register
. Write expected value in HSDIVIDER register
. Enable Mx HSDIVIDER clock output related functional clocks
        (CM_FCLKEN_xxx / CM_ICLKEN_xxx)
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Vijaykumar GN <vijaykumar.gn@ti.com>
[paul@pwsan.com: updated patch to apply; made workaround function static;
 marked as being 36xx-specific]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

This patch adds support in omap device layer to register devices
as early platform devices. Certain devices needed during system boot up
like timers, gpio etc can be registered as early devices. This will
allow for them to be probed very early on during system boot up.
This patch adds a parameter is_early_device in omap_device_build.
Depending on this parameter a call to early_platform_add_devices
or platform_register_device is made.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

In OMAP3 Some modules like Smartreflex do not have the regular sysconfig
register.Instead clockactivity bits are part of another register at a
different bit position than the usual bit positions 8 and 9.

In OMAP4, a new scheme is available  due to the new protocol
between the PRCM and the IPs. Depending of the scheme, the SYSCONFIG
bitfields position will be different.
The IP_REVISION register should be at offset 0x00.
It should contain a SCHEME field. From this we can determine whether
the IP follows legacy scheme or the new scheme.

31:30 SCHEME  Used to distinguish between old scheme and current.
 Read 0x0:  Legacy protocol.
 Read 0x1:  New PRCM protocol defined for new OMAP4 IPs

For legacy IP
 13:12 MIDLEMODE
 11:8  CLOCKACTIVITY
 6     EMUSOFT
 5     EMUFREE
 4:3   SIDLEMODE
 2     ENAWAKEUP
 1     SOFTRESET
 0     AUTOIDLE

For new OMAP4 IP's, the bit position in SYSCONFIG is (for simple target):
 5:4   STANDBYMODE (Ex MIDLEMODE)
 3:2   IDLEMODE (Ex SIDLEMODE)
 1     FREEEMU (Ex EMUFREE)
 0     SOFTRESET

Unfortunately In OMAP4 also some IPs will not follow any of these
two schemes. This is the case at least for McASP, SmartReflex
and some security IPs.

This patch introduces a new field sysc_fields in omap_hwmod_sysconfig which
can be used by the hwmod structures to specify the offsets for the
sysconfig register of the IP.Also two static structures
omap_hwmod_sysc_type1 and omap_hwmod_sysc_type2 are defined
which can be used directly to populate the sysc_fields if the IP follows
legacy or new OMAP4 scheme. If the IP follows none of these two schemes
a new omap_hwmod_sysc_fields structure has to be defined and
passed as part of omap_hwmod_sysconfig.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

DPLL_FREQSEL field in CLKEN_PLL register is no longer valid for
OMAP3630. So remove references to that.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
[paul@pwsan.com: added comment fix from Sergei Shtylyov]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

- missing return in omap_prcm_get_reset_sources()
- potential use of uninitialized variable in omap_prcm_arch_reset()
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

This patch checks if clk_get() returned success for
the clocks used in function omap2_clk_arch_init().

This version incorporates review comments from
Kevin Hilman and Paul Walmsley.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

This patch adds clock support for the following AM35xx modules
	- Ethernet MAC
	- CAN Controller (HECC)
	- New MUSB OTG Controller with integrated Phy
	- Video Processing Front End (VPFE)
	- Additional UART (UART4)
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Current implementation defines clock idle state indicators based on the
cpu information (cpu_is_omap24xx() or cpu_is_omap34xx()) in a system wide
manner. This patch extends the find_idlest() function in clkops to pass
back the idle state indicator for that clock, thus allowing idle state
indicators to be defined on a per clock basis if required.

This is specifically needed on AM35xx devices as the new IPSS clocks
indicates the idle status (0 is idle, 1 is ready) in a way just
opposite to how its handled in OMAP3 (0 is ready, 1 is idle).
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
[paul@pwsan.com: updated to apply after commit 98c45457 et seq.]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

This patch adds counters to keep track of whether the powerdomain
logic or software controllable memory banks are turned off when
the power domain enters retention. During power domain retention
if logic gets turned off, the scenario is known as Open Switch Retention.
Also during retention s/w controllable memory banks of a power
domain can be chosen to be kept in retention or off.

This patch adds one counter per powerdomain to track the power domain
logic state during retention. Number of memory bank state counters
added depends on the number of software controllable memory banks
of the powerdomain. To view these counters do
	cat ../debug/pm_debug/count
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: conditional expressions simplified; counter increment
 code moved to its own function]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

This patch adds the flag .pwrsts_logic_ret info for the core power domain
in the associated powerdomain structure. This flag specifies the states
core domain logic can hit in event of the domain entering retention.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

This patch adds APIs pwrdm_read_logic_retst and
pwrdm_read_mem_retst for reading the next programmed
logic and memory state a powerdomain is to hit in event
of the next power domain state being retention.
These are needed for OSWR support.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Added definitions for OMAP3430ES2_ST_SGX_SHIFT and OMAP3430ES2_ST_SGX_MASK
as these were missing.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Add _MASK suffix to CM_FCLKEN_IVA2 bitfieds to conform with the rest
of the usage in cm-regbits-34xx.h of using _SHIFT and _MASK suffixes.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The omap_device_[enable|idle|shutdown] functions print a warning
when called from an invalid state.  Print the invalid state in
the warning messages.  This also uses __func__ to get the function
name.

Also, move the entire print string onto a single line to facilitate
grepping or error messages.  Recent discussions on LKML show
strong preference for grep-able code vs. strict 80 column limit.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The omap_device struct contains a 'struct platform_device'.  Normally,
converting a platform_device pointer to an omap_device pointer
consists of simply doing a container_of(), as is done currently by the
to_omap_device() macro.

However, if this is attempted when using platform_device that has not
been created as part of the omap_device creation, the container_of()
will point to a memory location before the platform_device pointer
which will contain random data.

Therefore, we need a way to detect valid omap_device pointers.  This
patch solves this by using the simple magic number approach.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The check for a valid mux name should be performed regardless of whether
DEBUG_FS is enabled or not. Otherwise without DEBUG_FS, we get:

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
last sysfs file:
Modules linked in:
CPU: 0    Not tainted  (2.6.33-rc8 #10)
PC is at strcmp+0x18/0x40
LR is at omap_mux_init_signal+0x68/0x14c
...

This fixes the issue currently seen with boards not booting up
if DEBUG_FS is not enabled in defconfig.

Note that the earlier ifndef + ifdef now becomes simpler ifdef else:
If CONFIG_OMAP_MUX is selected, we use pin names. If it's not selected,
we only want the GPIO to mux register mapping.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add platform device for McPDM interface in OMAP4 and register
its memory and irq resources.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Define McPDM physical and L3 base address for OMAP4
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Support for McPDM IRQs in OMAP4
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

sdp4430_uart_config isn't used anywhere, so remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

AM3517/05 has few additional control module registers to control
the new IP's, like VPFE, USBOTG, CPGMAC.

This patch adds the bit defination for INTR_CLR and SW_RST control
register.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add base address definations for new AM35xx IPSS modules, like
VPFE, USBOTG, CPGMAC.

Please note that the OMAP34xx IVA2 memory space is being used for
AM35xx IPSS modules.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Changes for setting the padconf value for sys_nirq line which is
connected to T2 INTR1. This will fix the T2 keypad wakeup.
Signed-off-by: Lesly A M <x0080970@ti.com>
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Get rid of the ifdeffery in omap_mux_init by creating
omap_mux_init_package and omap_mux_init_signals functions.
Signed-off-by: Tony Lindgren <tony@atomide.com>

It is still possible to use the omap_hsmmc module
without the regulator framework.  Accordingly, ifdef
out regulator-specific functions.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

EMMC can have two voltage supplies, Vcc and VccQ
which are implemented in the code as consumer
supplies vmmc and vmmc_aux.

If the regulator that supplies vmmc_aux is shared
with other consumers, then sending it to sleep
will disrupt those consumers.  However, the
TWL4030-family regulators may have OFF remapped
to SLEEP, in which case 'regulator_disable()'
will put the regulator to sleep only when all
consumers are disabled - which is the desired
behaviour.

This patch adds a platform data field to allow
that option.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Stop using 'regulator_is_enabled()' and just pair enables
with disables so that the regulator reference counts can
work correctly.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Disable timeouts are in msecs not jiffies.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

An eMMC may be always powered on, so that the lowest
power saving state possible is sleeping. Add a field
to the platform data to indicate that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

It has been discovered that, when eMMC is powered off, current
will flow from OMAP eMMC data pull-ups to the eMMC voltage supply.
Configuring pads for OMAP off-mode does not help because eMMC is
powered off independently of OMAP off-mode.  Hence the pads are
now re-configured when eMMC is powered on or off.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Call the PM context-loss count function, now that there
is a prototype for it.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

hsmmc.[ch] no longer has any dependency on twl4030
and variable names should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>