- 28 Oct, 2023 1 commit
-
-
LihaSika authored
Change lower bcdDevice value for "Super Top USB 2.0 SATA BRIDGE" to match 1.50. I have such an older device with bcdDevice=1.50 and it will not work otherwise. Cc: stable@vger.kernel.org Signed-off-by:
Liha Sikanen <lihasika@gmail.com> Link: https://lore.kernel.org/r/ccf7d12a-8362-4916-b3e0-f4150f54affd@gmail.comSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 27 Oct, 2023 10 commits
-
-
Andrey Konovalov authored
Update USB_RAW_IOCTL_EVENT_FETCH to also report suspend, resume, reset, and disconnect events. This allows the code that emulates a USB device via Raw Gadget to handle these events. For example, the device can restart enumeration when it gets reset. Also do not print a WARNING when the event queue overflows. With these new events being queued, the queue might overflow if the device emulation code stops fetching events. Also print debug messages when a non-control event is received. Signed-off-by:
Andrey Konovalov <andreyknvl@gmail.com> Link: https://lore.kernel.org/r/d610b629a5f32fb76c24012180743f7f0f1872c0.1698350424.git.andreyknvl@gmail.comSigned-off-by:
-
Andrey Konovalov authored
During device operation, the host might decide to reset a device emulated via Raw Gadget. In this case, if the device emulation code has endpoint requests queued, usb_ep_queue will fail with -ESHUTDOWN. Currently, this disables the Raw Gadget device and makes the emulation code unable to proceed. Do not disable the Raw Gadget device if usb_ep_queue fails. Signed-off-by:
-
Andrey Konovalov authored
Currently, if a USB request that was queued by Raw Gadget is interrupted (via a signal), wait_for_completion_interruptible returns -ERESTARTSYS. Raw Gadget then attempts to propagate this value to userspace as a return value from its ioctls. However, when -ERESTARTSYS is returned by a syscall handler, the kernel internally restarts the syscall. This doesn't allow userspace applications to interrupt requests queued by Raw Gadget (which is required when the emulated device is asked to switch altsettings). It also violates the implied interface of Raw Gadget that a single ioctl must only queue a single USB request. Instead, make Raw Gadget do what GadgetFS does: check whether the request was interrupted (dequeued with status == -ECONNRESET) and report -EINTR to userspace. Fixes: f2c2e717 ("usb: gadget: add raw-gadget interface") Cc: stable <stable@kernel.org> Signed-off-by:
-
Pawel Laszczak authored
Patch removes TRB_FLUSH_ENDPOINT command from driver. This command is not supported by controller and USBSSP returns TRB Error completion code for it. Signed-off-by:
Pawel Laszczak <pawell@cadence.com> Acked-by:
Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20231026073737.165450-1-pawell@cadence.comSigned-off-by:
-
Uwe Kleine-König authored
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new(), which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). ast_udc_remove() is one of these functions that return an error code after doing only a partial cleanup. Replace the core's error message by a more drastic one and still convert the driver to .remove_new(). Note the only semantic change here is the changed error message. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20231026221701.2521483-2-u.kleine-koenig@pengutronix.deSigned-off-by:
-
Luca Weiss authored
The Orient-Chip OCP96011 is generally compatible with the FSA4480, add a compatible for it with the fallback on fsa4480. However the AUX/SBU connections are expected to be swapped compared to FSA4480, so document this in the data-lanes description. Signed-off-by:
Luca Weiss <luca.weiss@fairphone.com> Reviewed-by:
Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20231020-fsa4480-swap-v2-3-9a7f9bb59873@fairphone.comSigned-off-by:
-
Luca Weiss authored
On some hardware designs the AUX+/- lanes are connected reversed to SBU1/2 compared to the expected design by FSA4480. Made more complicated, the otherwise compatible Orient-Chip OCP96011 expects the lanes to be connected reversed compared to FSA4480. * FSA4480 block diagram shows AUX+ connected to SBU2 and AUX- to SBU1. * OCP96011 block diagram shows AUX+ connected to SBU1 and AUX- to SBU2. So if OCP96011 is used as drop-in for FSA4480 then the orientation handling in the driver needs to be reversed to match the expectation of the OCP96011 hardware. Support parsing the data-lanes parameter in the endpoint node to swap this in the driver. The parse_data_lanes_mapping function is mostly taken from nb7vpq904m.c. Reviewed-by:
Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by:
-
Luca Weiss authored
Allow specifying data-lanes to reverse the muxing orientation between AUX+/- and SBU1/2 where necessary by the hardware design. In the mux there's a switch that needs to be controlled from the OS, and it either connects AUX+ -> SBU1 and AUX- -> SBU2, or the reverse: AUX+ -> SBU2 and AUX- -> SBU1, depending on the orientation of how the USB-C connector is plugged in. With this data-lanes property we can now specify that AUX+ and AUX- connections are swapped between the SoC and the mux, therefore the OS needs to consider this and reverse the direction of this switch in the mux. _______ _______ | | | |-- HP --| | |-- MIC --| |or SoC | | MUX |-- SBU1 ---> To the USB-C Codec |-- AUX+ --| |-- SBU2 ---> connected |-- AUX- --| | ______| |_____| (thanks to Neil Armstrong for this ASCII art) Signed-off-by: -
Jimmy Hu authored
It is possible that typec_register_partner() returns ERR_PTR on failure. When port->partner is an error, a NULL pointer dereference may occur as shown below. [91222.095236][ T319] typec port0: failed to register partner (-17) ... [91225.061491][ T319] Unable to handle kernel NULL pointer dereference at virtual address 000000000000039f [91225.274642][ T319] pc : tcpm_pd_data_request+0x310/0x13fc [91225.274646][ T319] lr : tcpm_pd_data_request+0x298/0x13fc [91225.308067][ T319] Call trace: [91225.308070][ T319] tcpm_pd_data_request+0x310/0x13fc [91225.308073][ T319] tcpm_pd_rx_handler+0x100/0x9e8 [91225.355900][ T319] kthread_worker_fn+0x178/0x58c [91225.355902][ T319] kthread+0x150/0x200 [91225.355905][ T319] ret_from_fork+0x10/0x30 Add a check for port->partner to avoid dereferencing a NULL pointer. Fixes: 5e1d4c49 ("usb: typec: tcpm: Determine common SVDM Version") Cc: stable@vger.kernel.org Signed-off-by:
Jimmy Hu <hhhuuu@google.com> Link: https://lore.kernel.org/r/20231020012132.100960-1-hhhuuu@google.comSigned-off-by:
-
Greg Kroah-Hartman authored
Merge tag 'thunderbolt-for-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next Mika writes: thunderbolt: Changes for v6.7 merge window This includes following USB4/Thunderbolt changes for the v6.7 merge window: - Configure asymmetric link if the DisplayPort bandwidth requires so - Enable path power management packet support for USB4 v2 routers - Make the bandwidth reservations to follow the USB4 v2 connection manager guide suggestions - DisplayPort tunneling improvements - Small cleanups and improvements around the driver. All these have been in linux-next with no reported issues. * tag 'thunderbolt-for-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (25 commits) thunderbolt: Fix one kernel-doc comment thunderbolt: Configure asymmetric link if needed and bandwidth allows thunderbolt: Add support for asymmetric link thunderbolt: Introduce tb_switch_depth() thunderbolt: Introduce tb_for_each_upstream_port_on_path() thunderbolt: Introduce tb_port_path_direction_downstream() thunderbolt: Set path power management packet support bit for USB4 v2 routers thunderbolt: Change bandwidth reservations to comply USB4 v2 thunderbolt: Make is_gen4_link() available to the rest of the driver thunderbolt: Use weight constants in tb_usb3_consumed_bandwidth() thunderbolt: Use constants for path weight and priority thunderbolt: Add DP IN added last in the head of the list of DP resources thunderbolt: Create multiple DisplayPort tunnels if there are more DP IN/OUT pairs thunderbolt: Log NVM version of routers and retimers thunderbolt: Use tb_tunnel_xxx() log macros in tb.c thunderbolt: Expose tb_tunnel_xxx() log macros to the rest of the driver thunderbolt: Use tb_tunnel_dbg() where possible to make logging more consistent thunderbolt: Fix typo of HPD bit for Hot Plug Detect thunderbolt: Fix typo in enum tb_link_width kernel-doc thunderbolt: Fix debug log when DisplayPort adapter not available for pairing ...
-
- 24 Oct, 2023 3 commits
-
-
Greg Kroah-Hartman authored
This reverts commit eb3f1d9e. The patches for the features that these bindings described are still under active development, so odds are these bindings will also have to be changed in the future. As no in-tree code requires these bindings at the moment, revert them. Reported-by:
Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/ZTeObdjSSok0tttg@hovoldconsulting.com Cc: Bjorn Andersson <quic_bjorande@quicinc.com> Cc: Krishna Kurapati <quic_kriskura@quicinc.com> Signed-off-by:
-
Greg Kroah-Hartman authored
This reverts commit ca58c4ae. The patches for the features that these bindings described are still under active development, so odds are these bindings will also have to be changed in the future. As no in-tree code requires these bindings at the moment, revert them. Reported-by:
-
Yang Li authored
Fix a spelling errors in kernel doc comment, silence the warning: drivers/thunderbolt/tb.c:760: warning: expecting prototype for tb_maximum_banwidth(). Prototype was for tb_maximum_bandwidth() instead Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=7048Signed-off-by:
Yang Li <yang.lee@linux.alibaba.com> Signed-off-by:
Mika Westerberg <mika.westerberg@linux.intel.com>
-
- 21 Oct, 2023 26 commits
-
-
Hardik Gajjar authored
Previously, gadget assignment to the net device occurred exclusively during the initial binding attempt. Nevertheless, the gadget pointer could change during bind/unbind cycles due to various conditions, including the unloading/loading of the UDC device driver or the detachment/reconnection of an OTG-capable USB hub device. This patch relocates the gether_set_gadget() function out from ncm_opts->bound condition check, ensuring that the correct gadget is assigned during each bind request. The provided logs demonstrate the consistency of ncm_opts throughout the power cycle, while the gadget may change. * OTG hub connected during boot up and assignment of gadget and ncm_opts pointer [ 2.366301] usb 2-1.5: New USB device found, idVendor=2996, idProduct=0105 [ 2.366304] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.366306] usb 2-1.5: Product: H2H Bridge [ 2.366308] usb 2-1.5: Manufacturer: Aptiv [ 2.366309] usb 2-1.5: SerialNumber: 13FEB2021 [ 2.427989] usb 2-1.5: New USB device found, VID=2996, PID=0105 [ 2.428959] dabridge 2-1.5:1.0: dabridge 2-4 total endpoints=5, 0000000093a8d681 [ 2.429710] dabridge 2-1.5:1.0: P(0105) D(22.06.22) F(17.3.16) H(1.1) high-speed [ 2.429714] dabridge 2-1.5:1.0: Hub 2-2 P(0151) V(06.87) [ 2.429956] dabridge 2-1.5:1.0: All downstream ports in host mode [ 2.430093] gadget 000000003c414d59 ------> gadget pointer * NCM opts and associated gadget pointer during First ncm_bind [ 34.763929] NCM opts 00000000aa304ac9 [ 34.763930] NCM gadget 000000003c414d59 * OTG capable hub disconnecte or assume driver unload. [ 97.203114] usb 2-1: USB disconnect, device number 2 [ 97.203118] usb 2-1.1: USB disconnect, device number 3 [ 97.209217] usb 2-1.5: USB disconnect, device number 4 [ 97.230990] dabr_udc deleted * Reconnect the OTG hub or load driver assaign new gadget pointer. [ 111.534035] usb 2-1.1: New USB device found, idVendor=2996, idProduct=0120, bcdDevice= 6.87 [ 111.534038] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 111.534040] usb 2-1.1: Product: Vendor [ 111.534041] usb 2-1.1: Manufacturer: Aptiv [ 111.534042] usb 2-1.1: SerialNumber: Superior [ 111.535175] usb 2-1.1: New USB device found, VID=2996, PID=0120 [ 111.610995] usb 2-1.5: new high-speed USB device number 8 using xhci-hcd [ 111.630052] usb 2-1.5: New USB device found, idVendor=2996, idProduct=0105, bcdDevice=21.02 [ 111.630055] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 111.630057] usb 2-1.5: Product: H2H Bridge [ 111.630058] usb 2-1.5: Manufacturer: Aptiv [ 111.630059] usb 2-1.5: SerialNumber: 13FEB2021 [ 111.687464] usb 2-1.5: New USB device found, VID=2996, PID=0105 [ 111.690375] dabridge 2-1.5:1.0: dabridge 2-8 total endpoints=5, 000000000d87c961 [ 111.691172] dabridge 2-1.5:1.0: P(0105) D(22.06.22) F(17.3.16) H(1.1) high-speed [ 111.691176] dabridge 2-1.5:1.0: Hub 2-6 P(0151) V(06.87) [ 111.691646] dabridge 2-1.5:1.0: All downstream ports in host mode [ 111.692298] gadget 00000000dc72f7a9 --------> new gadget ptr on connect * NCM opts and associated gadget pointer during second ncm_bind [ 113.271786] NCM opts 00000000aa304ac9 -----> same opts ptr used during first bind [ 113.271788] NCM gadget 00000000dc72f7a9 ----> however new gaget ptr, that will not set in net_device due to ncm_opts->bound = true Signed-off-by:Hardik Gajjar <hgajjar@de.adit-jv.com> Link: https://lore.kernel.org/r/20231020153324.82794-1-hgajjar@de.adit-jv.comSigned-off-by:
-
Heiner Kallweit authored
Simplify the code by not calling hub_is_superspeed() twice. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/b1d77cbc-faa3-4d07-94ff-f6ffb85c6964@gmail.comSigned-off-by:
-
Badhri Jagan Sridharan authored
When transitioning from SNK_DEBOUNCED to unattached, its worthwhile to check for contaminant to mitigate wakeups. ``` [81334.219571] Start toggling [81334.228220] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected] [81334.305147] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected] [81334.305162] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS] [81334.305187] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS] [81334.475515] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms] [81334.486480] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_DEBOUNCED, polarity 0, disconnected] [81334.486495] state change SNK_DEBOUNCED -> SNK_DEBOUNCED [rev3 NONE_AMS] [81334.486515] pending state change SNK_DEBOUNCED -> SNK_UNATTACHED @ 20 ms [rev3 NONE_AMS] [81334.506621] state change SNK_DEBOUNCED -> SNK_UNATTACHED [delayed 20 ms] [81334.506640] Start toggling [81334.516972] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected] [81334.592759] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected] [81334.592773] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS] [81334.592792] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS] [81334.762940] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms] [81334.773557] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_DEBOUNCED, polarity 0, disconnected] [81334.773570] state change SNK_DEBOUNCED -> SNK_DEBOUNCED [rev3 NONE_AMS] [81334.773588] pending state change SNK_DEBOUNCED -> SNK_UNATTACHED @ 20 ms [rev3 NONE_AMS] [81334.793672] state change SNK_DEBOUNCED -> SNK_UNATTACHED [delayed 20 ms] [81334.793681] Start toggling [81334.801840] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected] [81334.878655] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected] [81334.878672] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS] [81334.878696] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS] [81335.048968] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms] [81335.060684] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_DEBOUNCED, polarity 0, disconnected] [81335.060754] state change SNK_DEBOUNCED -> SNK_DEBOUNCED [rev3 NONE_AMS] [81335.060775] pending state change SNK_DEBOUNCED -> SNK_UNATTACHED @ 20 ms [rev3 NONE_AMS] [81335.080884] state change SNK_DEBOUNCED -> SNK_UNATTACHED [delayed 20 ms] [81335.080900] Start toggling ``` Cc: stable@vger.kernel.org Fixes: 599f008c ("usb: typec: tcpm: Add callbacks to mitigate wakeups due to contaminant") Signed-off-by:
Badhri Jagan Sridharan <badhri@google.com> Acked-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20231015053108.2349570-1-badhri@google.comSigned-off-by:
-
Sebastian Reichel authored
RK3588 has three USB3 controllers. This adds the host-only controller, which is using the naneng-combphy shared with PCIe and SATA. The other two are dual-role and using a different PHY that is not yet supported upstream. Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Link: https://lore.kernel.org/r/20231020150022.48725-4-sebastian.reichel@collabora.comSigned-off-by:
-
Sebastian Reichel authored
On Rockchip RK3588 one of the DWC3 cores is integrated weirdly and requires two extra clocks to be enabled. Without these extra clocks hot-plugging USB devices is broken. Signed-off-by:
Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20231020150022.48725-3-sebastian.reichel@collabora.comSigned-off-by:
-
Sebastian Reichel authored
RK3588 has three DWC3 controllers. Two of them are fully functional in host, device and OTG mode including USB2 support. They are connected to dedicated PHYs, that also support USB-C's DisplayPort alternate mode. The third controller is connected to one of the combphy's shared with PCIe and SATA. It can only be used in host mode and does not support USB2. Compared to the other controllers this one needs some extra clocks. While adding the extra clocks required by RK3588, I noticed grf_clk is not available on RK3568, so I disallowed it for that platform. Signed-off-by:
Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20231020150022.48725-2-sebastian.reichel@collabora.comSigned-off-by:
-
Piyush Mehta authored
Add a reset-controller for supporting Xilinx versal platforms. To reset the USB controller, get the reset ID from device-tree and using ID trigger the reset, with the assert and deassert reset controller APIs for USB controller initialization. Signed-off-by:
Piyush Mehta <piyush.mehta@amd.com> Acked-by:
-
Uwe Kleine-König authored
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is (mostly) ignored and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. The function mtu3_remove() can only return a non-zero value if ssusb->dr_mode is neiter USB_DR_MODE_PERIPHERAL nor USB_DR_MODE_HOST nor USB_DR_MODE_OTG. In this case however the probe callback doesn't succeed and so the remove callback isn't called at all. So the code branch resulting in this error path could just be dropped were it not for the compiler choking on "enumeration value 'USB_DR_MODE_UNKNOWN' not handled in switch [-Werror=switch]". So instead replace this code path by a WARN_ON and then mtu3_remove() be converted to return void trivially. Signed-off-by:
-
Luca Weiss authored
Add a driver for the NXP PTN36502 Type-C USB 3.1 Gen 1 and DisplayPort v1.2 combo redriver. Reviewed-by:
-
Luca Weiss authored
Document bindings for this Type-C USB 3.1 Gen 1 and DisplayPort v1.2 combo redriver. The PTN36502 can also run in GPIO mode where it is configured differently, without any I2C connection, but this is not supported yet. Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Uwe Kleine-König authored
module_platform_driver_probe() has the advantage that the .probe() and .remove() calls can live in .init.text and .exit.text respectively and so some memory is saved. The downside is that dynamic bind and unbind are impossible. As the driver doesn't benefit from the advantages (both .probe and .remove are defined in plain .text), stop suffering from the downsides and use module_platform_driver() instead of module_platform_driver_probe(). Signed-off-by:
-
Uwe Kleine-König authored
module_platform_driver_probe() has the advantage that the .probe() and .remove() calls can live in .init.text and .exit.text respectively and so some memory is saved. The downside is that dynamic bind and unbind are impossible. As the driver doesn't benefit from the advantages (both .probe and .remove are defined in plain .text), stop suffering from the downsides and use module_platform_driver() instead of module_platform_driver_probe(). Signed-off-by:
-
Uwe Kleine-König authored
module_platform_driver_probe() has the advantage that the .probe() and .remove() calls can live in .init.text and .exit.text respectively and so some memory is saved. The downside is that dynamic bind and unbind are impossible. As the driver doesn't benefit from the advantages (both .probe and .remove are defined in plain .text), stop suffering from the downsides and use module_platform_driver() instead of module_platform_driver_probe(). Signed-off-by:
-
Uwe Kleine-König authored
module_platform_driver_probe() has the advantage that the .probe() and .remove() calls can live in .init.text and .exit.text respectively and so some memory is saved. The downside is that dynamic bind and unbind are impossible. As the driver doesn't benefit from the advantages (both .probe and .remove are defined in plain .text), stop suffering from the downsides and use module_platform_driver() instead of module_platform_driver_probe(). Signed-off-by:
-
Uwe Kleine-König authored
module_platform_driver_probe() has the advantage that the .probe() and .remove() calls can live in .init.text and .exit.text respectively and so some memory is saved. The downside is that dynamic bind and unbind are impossible. As the driver doesn't benefit from the advantages (both .probe and .remove are defined in plain .text), stop suffering from the downsides and use module_platform_driver() instead of module_platform_driver_probe(). Signed-off-by:
-
Uwe Kleine-König authored
module_platform_driver_probe() has the advantage that the .probe() and .remove() calls can live in .init.text and .exit.text respectively and so some memory is saved. The downside is that dynamic bind and unbind are impossible. As the driver doesn't benefit from the advantages (both .probe and .remove are defined in plain .text), stop suffering from the downsides and use module_platform_driver() instead of module_platform_driver_probe(). Signed-off-by:
-
Rob Herring authored
Commit 14485de4 ("usb: Use device_get_match_data()") dropped the unconditional use of ci_hdrc_usb2_of_match resulting in this warning: drivers/usb/chipidea/ci_hdrc_usb2.c:41:34: warning: unused variable 'ci_hdrc_usb2_of_match' [-Wunused-const-variable] The fix is to drop of_match_ptr() which is not necessary because DT is always used for this driver. Fixes: 14485de4 ("usb: Use device_get_match_data()") Reported-by:
kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202310131627.M43j234A-lkp@intel.com/Signed-off-by:
-
Tomer Maimon authored
Add Nuvoton NPCM BMC SoCs support to USB ChipIdea driver. NPCM SoC includes ChipIdea IP block that is used for USB device controller mode. Signed-off-by:
Tomer Maimon <tmaimon77@gmail.com> Acked-by:
-
Tomer Maimon authored
Add a compatible string for Nuvoton BMC NPCM750 and Nuvoton BMC NPCM845. Signed-off-by:
-
Tomer Maimon authored
Adding CI_HDRC_FORCE_VBUS_ACTIVE_ALWAYS flag to modify the vbus_active parameter to active in case the ChipIdea USB IP role is device-only and there is no otgsc register. Signed-off-by:
-
Jisheng Zhang authored
The "reset-gpios" is optional in real case, for example reset pin is is hard wired to "high". And this fact is also reflected by the devm_gpio_get_optional() calling in driver code. Signed-off-by:
Jisheng Zhang <jszhang@kernel.org> Acked-by:
-
Milan Broz authored
Switch internal usb-storage quirk value to 64-bit as quirks currently use all 32 bits. Signed-off-by:
Milan Broz <gmazyland@gmail.com> Reviewed-by:
Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20231016072604.40179-3-gmazyland@gmail.comSigned-off-by:
-
Milan Broz authored
This patch removes macro that was used only by commit that was reverted in commit ab4b7164 ("USB: storage: fix Huawei mode switching regression") Signed-off-by:
-
Wesley Cheng authored
There is a 120ms delay implemented for allowing the XHCI host controller to detect a U3 wakeup pulse. The intention is to wait for the device to retry the wakeup event if the USB3 PORTSC doesn't reflect the RESUME link status by the time it is checked. As per the USB3 specification: tU3WakeupRetryDelay ("Table 7-12. LTSSM State Transition Timeouts") This would allow the XHCI resume sequence to determine if the root hub needs to be also resumed. However, in case there is no device connected, or if there is only a HSUSB device connected, this delay would still affect the overall resume timing. Since this delay is solely for detecting U3 wake events (USB3 specific) then ignore this delay for the disconnected case and the HSUSB connected only case. [skip helper function, rename usb3_connected variable -Mathias ] Signed-off-by:Wesley Cheng <quic_wcheng@quicinc.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20231019102924.2797346-20-mathias.nyman@linux.intel.comSigned-off-by:
-
Sergey Shtylyov authored
If this driver enables the xHC clocks while resuming from sleep, it calls clk_prepare_enable() without checking for errors and blithely goes on to read/write the xHC's registers -- which, with the xHC not being clocked, at least on ARM32 usually causes an imprecise external abort exceptions which cause kernel oops. Currently, the chips for which the driver does the clock dance on suspend/resume seem to be the Broadcom STB SoCs, based on ARM32 CPUs, as it seems... Found by Linux Verification Center (linuxtesting.org) with the Svace static analysis tool. Fixes: 8bd954c5 ("usb: host: xhci-plat: suspend and resume clocks") Signed-off-by:
Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by:
-
Udipto Goswami authored
In some situations where xhci removal happens parallel to xhci_handshake, we encounter a scenario where the xhci_handshake can't succeed, and it polls until timeout. If xhci_handshake runs until timeout it can on some platforms result in a long wait which might lead to a watchdog timeout. Add a helper that checks xhci status during the handshake, and exits if set state is entered. Use this helper in places where xhci_handshake is called unlocked and has a long timeout. For example xhci command timeout and xhci reset. [commit message and code comment rewording -Mathias] Signed-off-by:
Udipto Goswami <quic_ugoswami@quicinc.com> Signed-off-by:
-
