- 20 May, 2015 40 commits
-
-
Ulf Hansson authored
commit 53d26698 upstream. The GPIO regulator for the SD-card isn't a ux500 SOC configuration, but instead it's specific to the board. Move the definition of it, into the board DTSs. Fixes: c94a4ab7 ("ARM: ux500: Disable the MMCI gpio-regulator by default") Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by:
Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Eric W. Biederman authored
commit 7e96c1b0 upstream. This fixes a dumb bug in fs_fully_visible that allows proc or sys to be mounted if there is a bind mount of part of /proc/ or /sys/ visible. Reported-by:
Eric Windisch <ewindisch@docker.com> Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Al Viro authored
commit f15133df upstream. path_openat() jumps to the wrong place after do_tmpfile() - it has already done path_cleanup() (as part of path_lookupat() called by do_tmpfile()), so doing that again can lead to double fput(). Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> [ luis: backported to 3.16: - adjusted context as 3.16 doesn't have path_cleanup() helper, introduced by 893b7775 ("fs/namei.c: new helper (path_cleanup())") ] Signed-off-by:
-
Christian König authored
commit d52cdfa4 upstream. MPEG 2/4 are only supported since UVD3. Signed-off-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Christian König authored
commit a1b403da upstream. Invalid messages can crash the hw otherwise. Signed-off-by:
-
Christian König authored
commit 29c63fe2 upstream. Invalid handles can crash the hw. Signed-off-by:
-
Jani Nikula authored
commit 9fcb1704 upstream. The eDP port A register on PCH split platforms has a slightly different register layout from the other ports, with bit 6 being either alternate scrambler reset or reserved, depending on the generation. Our misinterpretation of the bit as audio has lead to warning. Fix this by not enabling audio on port A, since none of our platforms support audio on port A anyway. v2: DDI doesn't have audio on port A either (Sivakumar Thulasimani) Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89958Reported-and-tested-by:
Chris Bainbridge <chris.bainbridge@gmail.com> Reviewed-by:
Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Junxiao Bi authored
commit b1432a2a upstream. There is a race window in dlm_get_lock_resource(), which may return a lock resource which has been purged. This will cause the process to hang forever in dlmlock() as the ast msg can't be handled due to its lock resource not existing. dlm_get_lock_resource { ... spin_lock(&dlm->spinlock); tmpres = __dlm_lookup_lockres_full(dlm, lockid, namelen, hash); if (tmpres) { spin_unlock(&dlm->spinlock); >>>>>>>> race window, dlm_run_purge_list() may run and purge the lock resource spin_lock(&tmpres->spinlock); ... spin_unlock(&tmpres->spinlock); } } Signed-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <joseph.qi@huawei.com> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Ryusuke Konishi authored
commit d8fd150f upstream. The range check for b-tree level parameter in nilfs_btree_root_broken() is wrong; it accepts the case of "level == NILFS_BTREE_LEVEL_MAX" even though the level is limited to values in the range of 0 to (NILFS_BTREE_LEVEL_MAX - 1). Since the level parameter is read from storage device and used to index nilfs_btree_path array whose element count is NILFS_BTREE_LEVEL_MAX, it can cause memory overrun during btree operations if the boundary value is set to the level parameter on device. This fixes the broken sanity check and adds a comment to clarify that the upper bound NILFS_BTREE_LEVEL_MAX is exclusive. Signed-off-by:
Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Signed-off-by:
-
Naoya Horiguchi authored
commit 602498f9 upstream. If multiple soft offline events hit one free page/hugepage concurrently, soft_offline_page() can handle the free page/hugepage multiple times, which makes num_poisoned_pages counter increased more than once. This patch fixes this wrong counting by checking TestSetPageHWPoison for normal papes and by checking the return value of dequeue_hwpoisoned_huge_page() for hugepages. Signed-off-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Acked-by:
Dean Nelson <dnelson@redhat.com> Cc: Andi Kleen <andi@firstfloor.org> Signed-off-by:
-
Naoya Horiguchi authored
commit 09789e5d upstream. Currently memory_failure() calls shake_page() to sweep pages out from pcplists only when the victim page is 4kB LRU page or thp head page. But we should do this for a thp tail page too. Consider that a memory error hits a thp tail page whose head page is on a pcplist when memory_failure() runs. Then, the current kernel skips shake_pages() part, so hwpoison_user_mappings() returns without calling split_huge_page() nor try_to_unmap() because PageLRU of the thp head is still cleared due to the skip of shake_page(). As a result, me_huge_page() runs for the thp, which is broken behavior. One effect is a leak of the thp. And another is to fail to isolate the memory error, so later access to the error address causes another MCE, which kills the processes which used the thp. This patch fixes this problem by calling shake_page() for thp tail case. Fixes: 385de357 ("thp: allow a hwpoisoned head page to be put back to LRU") Signed-off-by:
Andi Kleen <ak@linux.intel.com> Acked-by:
-
Boris Ostrovsky authored
commit 16e6bd59 upstream. .. because bind_evtchn_to_cpu(evtchn, cpu) will map evtchn to 'info' and pass 'info' down to xen_evtchn_port_bind_to_cpu(). Signed-off-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Tested-by:
Annie Li <annie.li@oracle.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Boris Ostrovsky authored
commit b9d934f2 upstream. After a resume the hypervisor/tools may change console event channel number. We should re-query it. Signed-off-by:
-
Boris Ostrovsky authored
commit 16f1cf3b upstream. After a resume the hypervisor/tools may change xenbus event channel number. We should re-query it. Signed-off-by:
-
Boris Ostrovsky authored
commit 5cec9883 upstream. When a guest is resumed, the hypervisor may change event channel assignments. If this happens and the guest uses 2-level events it is possible for the interrupt to be claimed by wrong VCPU since cpu_evtchn_mask bits may be stale. This can happen even though evtchn_2l_bind_to_cpu() attempts to clear old bits: irq_info that is passed in is not necessarily the original one (from pre-migration times) but instead is freshly allocated during resume and so any information about which CPU the channel was bound to is lost. Thus we should clear the mask during resume. We also need to make sure that bits for xenstore and console channels are set when these two subsystems are resumed. While rebind_evtchn_irq() (which is invoked for both of them on a resume) calls irq_set_affinity(), the latter will in fact postpone setting affinity until handling the interrupt. But because cpu_evtchn_mask will have bits for these two cleared we won't be able to take the interrupt. With that in mind, we need to bind those two channels explicitly in rebind_evtchn_irq(). We will keep irq_set_affinity() so that we have a pass through generic irq affinity code later, in case something needs to be updated there as well. (Also replace cpumask_of(0) with cpumask_of(info->cpu) in rebind_evtchn_irq(): it should be set to zero in preceding xen_irq_info_evtchn_setup().) Signed-off-by:
-
Dan Carpenter authored
commit d67e1996 upstream. I spotted two (difficult to hit) bugs while reviewing this. 1) There is a double free bug because we unregister "map_kset" in add_sysfs_runtime_map_entry() and also efi_runtime_map_init(). 2) If we fail to allocate "entry" then we should return ERR_PTR(-ENOMEM) instead of NULL. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Cc: Dave Young <dyoung@redhat.com> Cc: Guangyu Sun <guangyu.sun@oracle.com> Signed-off-by:
Matt Fleming <matt.fleming@intel.com> Signed-off-by:
-
Lukas Wunner authored
commit 3916e3fd upstream. Single channel LVDS maxes out at 112 MHz. The 15" pre-retina models shipped with 1440x900 (106 MHz) by default or 1680x1050 (119 MHz) as a BTO option, both versions used dual channel LVDS even though the smaller one would have fit into a single channel. Notes: Bug report showing that the MacBookPro8,2 with 1440x900 uses dual channel LVDS (this lead to it being hardcoded in intel_lvds.c by Daniel Vetter with commit 618563e3): https://bugzilla.kernel.org/show_bug.cgi?id=42842 If i915.lvds_channel_mode=2 is missing even though the machine needs it, every other vertical line is white and consequently, only the left half of the screen is visible (verified by myself on a MacBookPro9,1). Forum posting concerning a MacBookPro6,2 with 1440x900, author is using i915.lvds_channel_mode=2 on the kernel command line, proving that the machine uses dual channels: https://bbs.archlinux.org/viewtopic.php?id=185770 Chi Mei N154C6-L04 with 1440x900 is a replacement panel for all MacBook Pro "A1286" models, and that model number encompasses the MacBookPro6,2 / 8,2 / 9,1. Page 17 of the panel's datasheet shows it's driven with dual channel LVDS: http://www.ebay.com/itm/-/400690878560 http://www.everymac.com/ultimate-mac-lookup/?search_keywords=A1286 http://www.taopanel.com/chimei/datasheet/N154C6-L04.pdf Those three 15" models, MacBookPro6,2 / 8,2 / 9,1, are the only ones with i915 graphics and dual channel LVDS, so that list should be complete. And the 8,2 is already in intel_lvds.c. Possible motivation to use dual channel LVDS even on the 1440x900 models: Reduce the number of different parts, i.e. use identical logic boards and display cabling on both versions and the only differing component is the panel. Signed-off-by:
Lukas Wunner <lukas@wunner.de> Acked-by:
-
Jason Gunthorpe authored
commit 28521440 upstream. When accepting a new IPv4 connect to an IPv6 socket, the CMA tries to canonize the address family to IPv4, but does not properly process the listening sockaddr to get the listening port, and does not properly set the address family of the canonized sockaddr. Fixes: e51060f0 ("IB: IP address based RDMA connection manager") Reported-By:
Yotam Kenneth <yotamke@mellanox.com> Signed-off-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Tested-by:
Haggai Eran <haggaie@mellanox.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Christian König authored
commit 013ead48 upstream. Hardware doesn't seem to work correctly, just block userspace in this case. v2: add missing defines Bugs: https://bugs.freedesktop.org/show_bug.cgi?id=85320Signed-off-by:
-
Pavel Machek authored
commit 1819e303 upstream. N900 audio recording needs that codec provides bias voltage for integrated digital microphone and headset microphone depending which one is used. Digital microphone uses 2 V bias and it comes from the codec A part. Codec B part drives the headset microphone bias and that is set to 2.5 V. Signed-off-by:
Pavel Machek <pavel@ucw.cz> [Jarkko: Headset mic bias changed to 2 (2.5 V) as it was before commit e2e8bfdf ("ASoC: tlv320aic3x: Convert mic bias to a supply widget")] Signed-off-by:
Jarkko Nikula <jarkko.nikula@bitmer.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Tony Lindgren authored
commit 102bcb6e upstream. If we use a combination of VMODE and I2C4 for retention modes, eventually the off idle power consumption will creep up by about 23mW, even during off mode with I2C4 always staying enabled. Turns out this is because of erratum i531 "Extra Power Consumed When Repeated Start Operation Mode Is Enabled on I2C Interface Dedicated for Smart Reflex (I2C4)" as pointed out by Nishanth Menon <nm@ti.com>. Let's fix the issue by adding i2c_cfg_clear_mask for the bits to clear when initializing the I2C4 adapter so we can clear SREN bit that drives the I2C4 lines low otherwise when there is no traffic. Fixes: 3b8c4ebb ("ARM: OMAP3: Fix idle mode signaling for sys_clkreq and sys_off_mode") Cc: Kevin Hilman <khilman@kernel.org> Cc: Tero Kristo <t-kristo@ti.com> Reviewed-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
-
Witold Szczeponik authored
commit 622532bb upstream. Commit eec15edb (ACPI / PNP: use device ID list for PNPACPI device enumeration) changed the way how ACPI devices are enumerated and when they are added to the PNP bus. However, it broke the sound card support on (at least) a vintage IBM ThinkPad 600E: with said commit applied, two of the necessary "CSC01xx" devices are not added to the PNP bus and hence can not be found during the initialization of the "snd-cs4236" module. As a consequence, loading "snd-cs4236" causes null pointer exceptions. The attached patch fixes the problem end re-enables sound on the IBM ThinkPad 600E. Fixes: eec15edb (ACPI / PNP: use device ID list for PNPACPI device enumeration) Signed-off-by:
Witold Szczeponik <Witold.Szczeponik@gmx.net> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Johan Hovold authored
commit 483d8211 upstream. Unregister GPIOs requested through sysfs at chip remove to avoid leaking the associated memory and sysfs entries. The stale sysfs entries prevented the gpio numbers from being exported when the gpio range was later reused (e.g. at device reconnect). This also fixes the related module-reference leak. Note that kernfs makes sure that any on-going sysfs operations finish before the class devices are unregistered and that further accesses fail. The chip exported flag is used to prevent gpiod exports during removal. This also makes it harder to trigger, but does not fix, the related race between gpiochip_remove and export_store, which is really a race with gpiod_request that needs to be addressed separately. Also note that this would prevent the crashes (e.g. NULL-dereferences) at reconnect that affects pre-3.18 kernels, as well as use-after-free on operations on open attribute files on pre-3.14 kernels (prior to kernfs). Fixes: d8f388d8 ("gpio: sysfs interface") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
commit 01cca93a upstream. Unregister gpiochip device (used to export information through sysfs) before removing it internally. This way removal will reverse addition. Signed-off-by:
-
Marek Vasut authored
commit 4ada77e3 upstream. Fix a typo in the TX DMA interrupt name for AUART4. This patch makes AUART4 operational again. Signed-off-by:
Marek Vasut <marex@denx.de> Fixes: f30fb03d ("ARM: dts: add generic DMA device tree binding for mxs-dma") Acked-by:
Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Markus Pargmann authored
commit f90d3f0d upstream. The property '#pwm-cells' is currently missing. It is not possible to use pwm4 without this property. Signed-off-by:
Markus Pargmann <mpa@pengutronix.de> Fixes: 5658a68f ("ARM i.MX25: Add devicetree") Reviewed-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Philipp Zabel authored
commit 7f8d49dc upstream. The fixed-regulator bindings require a separate property enable-active-high, the standard gpio phandle property polarity setting is ignored. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Fixes: 4fe69a93 ("ARM: dts: Add Phytec pfla02 with i.MX6 DualLite/Solo") Signed-off-by:
-
Stefan Wahren authored
commit 0fdebe1a upstream. The dr_mode of usb0 on imx233-olinuxino is left to default "otg". Since the green LED (GPIO2_1) on imx233-olinuxino is connected to the same pin as USB_OTG_ID it's possible to disable USB host by LED toggling: echo 0 > /sys/class/leds/green/brightness [ 1068.890000] ci_hdrc ci_hdrc.0: remove, state 1 [ 1068.890000] usb usb1: USB disconnect, device number 1 [ 1068.920000] usb 1-1: USB disconnect, device number 2 [ 1068.920000] usb 1-1.1: USB disconnect, device number 3 [ 1069.070000] usb 1-1.2: USB disconnect, device number 4 [ 1069.450000] ci_hdrc ci_hdrc.0: USB bus 1 deregistered [ 1074.460000] ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11 This patch fixes the issue by setting dr_mode to "host" in the dts file. Reported-by:
Harald Geyer <harald@ccbib.org> Signed-off-by:
Peter Chen <peter.chen@freescale.com> Fixes: b4931294 ("ARM: dts: imx23-olinuxino: Add USB host support") Signed-off-by:
-
Fabio Estevam authored
commit cfe8c597 upstream. On imx23-olinuxino the LED turns on when level logic high is aplied to GPIO2_1. Fix the gpios property accordingly. Fixes: b34aa185 ("ARM: dts: imx23-olinuxino: Remove unneeded "default-on"") Reported-by:
-
Gregory CLEMENT authored
commit 750e30d4 upstream. There is no crystal connected to the internal RTC on the Open Block AX3. So let's disable it in order to prevent the kernel probing the driver uselessly. Eventually this patches removes the following warning message from the boot log: "rtc-mv d0010300.rtc: internal RTC not ticking" Acked-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Tejun Heo authored
commit 464d1387 upstream. mm/page-writeback.c has several places where 1 is added to the divisor to prevent division by zero exceptions; however, if the original divisor is equivalent to -1, adding 1 leads to division by zero. There are three places where +1 is used for this purpose - one in pos_ratio_polynom() and two in bdi_position_ratio(). The second one in bdi_position_ratio() actually triggered div-by-zero oops on a machine running a 3.10 kernel. The divisor is x_intercept - bdi_setpoint + 1 == span + 1 span is confirmed to be (u32)-1. It isn't clear how it ended up that but it could be from write bandwidth calculation underflow fixed by c72efb65 ("writeback: fix possible underflow in write bandwidth calculation"). At any rate, +1 isn't a proper protection against div-by-zero. This patch converts all +1 protections to |1. Note that bdi_update_dirty_ratelimit() was already using |1 before this patch. Signed-off-by:
Tejun Heo <tj@kernel.org> Reviewed-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Ming Lei authored
commit 2a34c087 upstream. hctx->tags has to be set as NULL in case that it is to be unmapped no matter if set->tags[hctx->queue_num] is NULL or not in blk_mq_map_swqueue() because shared tags can be freed already from another request queue. The same situation has to be considered during handling CPU online too. Unmapped hw queue can be remapped after CPU topo is changed, so we need to allocate tags for the hw queue in blk_mq_map_swqueue(). Then tags allocation for hw queue can be removed in hctx cpu online notifier, and it is reasonable to do that after mapping is updated. Reported-by:
Dongsu Park <dongsu.park@profitbricks.com> Tested-by:
Ming Lei <ming.lei@canonical.com> Signed-off-by:
-
Roy Franz authored
commit 98b228f5 upstream. Until now, the EFI stub was only setting the 32 bit cmd_line_ptr in the setup_header structure, so on 64 bit platforms this could be truncated. This patch adds setting the upper bits of the buffer address in ext_cmd_line_ptr. This case was likely never hit, as the allocation for this buffer is done at the lowest available address. Only x86_64 kernels have this problem, as the 1-1 mapping mandated by EFI ensures that all memory is 32 bit addressable on 32 bit platforms. The EFI stub does not support mixed mode, so the 32 bit kernel on 64 bit firmware case does not need to be handled. Signed-off-by:
Roy Franz <roy.franz@linaro.org> Signed-off-by:
-
Ross Lagerwall authored
commit c57dcb56 upstream. Some buggy firmware implementations update VariableNameSize on success such that it does not include the final NUL character which results in garbage in the efivarfs name entries. Use kzalloc on the efivar_entry (as is done in efivars.c) to ensure that the name is always NUL-terminated. The buggy firmware is: BIOS Information Vendor: Intel Corp. Version: S1200RP.86B.02.02.0005.102320140911 Release Date: 10/23/2014 BIOS Revision: 4.6 System Information Manufacturer: Intel Corporation Product Name: S1200RP_SE Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Acked-by:
Matthew Garrett <mjg59@coreos.com> Cc: Jeremy Kerr <jk@ozlabs.org> Signed-off-by:
-
Florian Westphal authored
commit 330966e5 upstream. skb_gso_segment has three possible return values: 1. a pointer to the first segmented skb 2. an errno value (IS_ERR()) 3. NULL. This can happen when GSO is used for header verification. However, several callers currently test IS_ERR instead of IS_ERR_OR_NULL and would oops when NULL is returned. Note that these call sites should never actually see such a NULL return value; all callers mask out the GSO bits in the feature argument. However, there have been issues with some protocol handlers erronously not respecting the specified feature mask in some cases. It is preferable to get 'have to turn off hw offloading, else slow' reports rather than 'kernel crashes'. Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Christoffer Dall authored
commit ae705930 upstream. There is an interesting bug in the vgic code, which manifests itself when the KVM run loop has a signal pending or needs a vmid generation rollover after having disabled interrupts but before actually switching to the guest. In this case, we flush the vgic as usual, but we sync back the vgic state and exit to userspace before entering the guest. The consequence is that we will be syncing the list registers back to the software model using the GICH_ELRSR and GICH_EISR from the last execution of the guest, potentially overwriting a list register containing an interrupt. This showed up during migration testing where we would capture a state where the VM has masked the arch timer but there were no interrupts, resulting in a hung test. Cc: Marc Zyngier <marc.zyngier@arm.com> Reported-by:
Alex Bennee <alex.bennee@linaro.org> Signed-off-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
Shannon Zhao <shannon.zhao@linaro.org> [ luis: backported to 3.16: used shannon's backport to 3.14 ] Signed-off-by:
-
Marc Zyngier authored
commit 04b8dc85 upstream. The kernel's pgd_index macro is designed to index a normal, page sized array. KVM is a bit diffferent, as we can use concatenated pages to have a bigger address space (for example 40bit IPA with 4kB pages gives us an 8kB PGD. In the above case, the use of pgd_index will always return an index inside the first 4kB, which makes a guest that has memory above 0x8000000000 rather unhappy, as it spins forever in a page fault, whist the host happilly corrupts the lower pgd. The obvious fix is to get our own kvm_pgd_index that does the right thing(tm). Tested on X-Gene with a hacked kvmtool that put memory at a stupidly high address. Reviewed-by:
-
Marc Zyngier authored
commit 801f6772 upstream. Commit b856a591 (arm/arm64: KVM: Reset the HCR on each vcpu when resetting the vcpu) moved the init of the HCR register to happen later in the init of a vcpu, but left out the fixup done in kvm_reset_vcpu when preparing for a 32bit guest. As a result, the 32bit guest is run as a 64bit guest, but the rest of the kernel still manages it as a 32bit. Fun follows. Moving the fixup to vcpu_reset_hcr solves the problem for good. Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Marc Zyngier authored
commit 55e858b7 upstream. It took about two years for someone to notice that the IPA passed to TLBI IPAS2E1IS must be shifted by 12 bits. Clearly our reviewing is not as good as it should be... Paper bag time for me. Reported-by:
Mario Smarduch <m.smarduch@samsung.com> Tested-by:
-
Christoffer Dall authored
commit 05971120 upstream. It is curently possible to run a VM with architected timers support without creating an in-kernel VGIC, which will result in interrupts from the virtual timer going nowhere. To address this issue, move the architected timers initialization to the time when we run a VCPU for the first time, and then only initialize (and enable) the architected timers if we have a properly created and initialized in-kernel VGIC. When injecting interrupts from the virtual timer to the vgic, the current setup should ensure that this never calls an on-demand init of the VGIC, which is the only call path that could return an error from kvm_vgic_inject_irq(), so capture the return value and raise a warning if there's an error there. We also change the kvm_timer_init() function from returning an int to be a void function, since the function always succeeds. Reviewed-by:
-
