The correct terminology is serial NOR flash or SPI NOR.
s/SPI-NOR/SPI NOR and s/spi-nor/SPI NOR across the subsystem.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

s25fs256s was identified as s25fl256s. Differentiate between them by
the Family ID using the INFO6 macro.

Fixes: b199489d ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>

Add support for Cypress s25fs128s1 flash. Previously the flash is
decoded as s25fl129p1 by mistake.

Add it in the flash info list to correctly decode. The flash also
needs a fixup for s25fs-s family. Further capability of the flash will
be parsed from bfpt.

The flash has been tested under SPI/DUAL/QUAD mode on hisi-sfc-v3xx
controller, all the write/read/erase works well.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

Spansion S25FS-S family has an issue in the Basic Flash Parameter Table
(BFPT): Dword-11 bits 7:4 specify a page size of 512 bytes.  Actually
this is configurable in the vendor unique register (CR3V) and even the
factory default setting is to "wrap at 256 bytes", so blindly relying
on BFPT breaks the page writes on these chips. Add the post-BFPT fixup
which restores the default page size of 256 bytes -- to properly read
CR3V this early is quite intrusive and should better be done as a new
feature; Alexander Sverdlin had the patch doing that:

https://patchwork.ozlabs.org/project/linux-mtd/patch/20200227123657.26030-1-alexander.sverdlin@nokia.com/

Fixes: dfd2b745 ("mtd: spi-nor: add Spansion S25FS512S ID")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

The functions return 1 if ready, 0 if not ready, -errno on errors.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

spi_nor_ready() returns 1 if ready, 0 if not ready and -errno on errors.
Do the same in all the spi_nor_*_ready() children.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

n25q00 uses the 4 bit Block Protection scheme and supports Top/Bottom
protection via the BP and TB bits of the Status Register.
Enable locking for n25q00. Tested with cirrus controller.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

mx25u51245g is a mass production for new design and
replace mx66u51235f(phase out).

Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

mx25l51245g is a mass production for new design and
replace mx66l51235l(phase out).

Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

When spi_nor_info_init_params(), spi_nor_sfdp_init_params(), and
spi_nor_init_params() were added, the kernel-doc for them contained
a typo: 'struct spi-nor' instead of 'struct spi_nor' -- fix them.

Fixes: 1c1d8d98 ("mtd: spi-nor: Split spi_nor_init_params()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

When spi_nor_manufacturer_init_params() was added, the kernel-doc for it
contained a typo: 'struct spi-nor' instead of 'struct spi_nor' -- fix it.

Fixes: ce0b6f3f ("mtd: spi-nor: Add default_init() hook to tweak flash parameters")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

When adding the 'spimem' field to 'struct spi_nor', a grammar mistake
("point" instead of "pointer") was made -- fix it and convert the SPI
acronym to uppercase and fully spell out "memory", while at it...

Fixes: b35b9a10 ("mtd: spi-nor: Move m25p80 code in spi-nor.c")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

When adding the 'info' field to 'struct spi_nor', some acronyms were in
lower case and some in upper case and the JEDEC acronym mistyped -- fix
these issues.

Fixes: 46dde01f ("mtd: spi-nor: add spi_nor_init() function")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

When adding the '{read|write|reg}_proto' fields to 'struct spi_nor', a
colon was missed in the comment for the spi_nor::reg_proto' -- add it.

Fixes: cfc5604c ("mtd: spi-nor: introduce SPI 1-2-2 and SPI 1-4-4 protocols")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

When embedding 'struct mtd_info' within 'struct spi_nor', the kernel-doc
comment was forgotten. Fix it by dropping the "pointer to" part from the
comment.

Fixes: 19763671 ("mtd: spi-nor: embed struct mtd_info within struct spi_nor")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

When introducing 'struct spi_nor', a number of issues was added in its
kernel-doc comment:

- double article in the heading kernel-doc comment;
- "point" instead of "pointer" for the 'mtd' and 'dev' fields;
- "a" articles instead of "an" for the 'dev' field;
- acronyms in the lower case for the 'dev' field;
- missing "pointer to" for the 'priv' field.

Fix all of those at once...

Fixes: 6e602ef7 ("mtd: spi-nor: add the basic data structures")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

As 4bit block protection patchset for some micron models are merged,
n25q128a11 also uses 4 bit Block Protection scheme, so enable locking
for it. Tested it on n25q128a11, the locking functions work well.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Jungseung Lee <js07.lee@samsung.com>
Tested-by: Shreyas Joshi <shreyasjoshi15@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

The s25fl256s0 supports dual and quad read like s25fl256s1.
Enable it by adding SPI_NOR_DUAL_READ and SPI_NOR_QUAD_READ
flags to the flash_info entry. Tested with the device and
confirmed that is working.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@cypress.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

The write disable (WRDI) opcode is not really specific to the SST flashes
(anymore?) -- move the #define to the main opcode group, just before WREN.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

When remapping a mapping where a portion of a VMA is remapped
into another portion of the VMA it can cause the VMA to become
split. During the copy_vma operation the VMA can actually
be remerged if it's an anonymous VMA whose pages have not yet
been faulted. This isn't normally a problem because at the end
of the remap the original portion is unmapped causing it to
become split again.

However, MREMAP_DONTUNMAP leaves that original portion in place which
means that the VMA which was split and then remerged is not actually
split at the end of the mremap. This patch fixes a bug where
we don't detect that the VMAs got remerged and we end up
putting back VM_ACCOUNT on the next mapping which is completely
unreleated. When that next mapping is unmapped it results in
incorrectly unaccounting for the memory which was never accounted,
and eventually we will underflow on the memory comittment.

There is also another issue which is similar, we're currently
accouting for the number of pages in the new_vma but that's wrong.
We need to account for the length of the remap operation as that's
all that is being added. If there was a mapping already at that
location its comittment would have been adjusted as part of
the munmap at the start of the mremap.

A really simple repro can be seen in:
https://gist.github.com/bgaff/e101ce99da7d9a8c60acc641d07f312c

Fixes: e346b381 ("mm/mremap: add MREMAP_DONTUNMAP to mremap()")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Brian Geffon <bgeffon@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull clk fixes from Stephen Boyd:
 "Two build fixes for a couple clk drivers and a fix for the Unisoc
  serial clk where we want to keep it on for earlycon"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: sprd: don't gate uart console clock
  clk: mmp2: fix link error without mmp2
  clk: asm9260: fix __clk_hw_register_fixed_rate_with_accuracy typo

Pull x86 and objtool fixes from Thomas Gleixner:
 "A set of fixes for x86 and objtool:

  objtool:

   - Ignore the double UD2 which is emitted in BUG() when
     CONFIG_UBSAN_TRAP is enabled.

   - Support clang non-section symbols in objtool ORC dump

   - Fix switch table detection in .text.unlikely

   - Make the BP scratch register warning more robust.

  x86:

   - Increase microcode maximum patch size for AMD to cope with new CPUs
     which have a larger patch size.

   - Fix a crash in the resource control filesystem when the removal of
     the default resource group is attempted.

   - Preserve Code and Data Prioritization enabled state accross CPU
     hotplug.

   - Update split lock cpu matching to use the new X86_MATCH macros.

   - Change the split lock enumeration as Intel finaly decided that the
     IA32_CORE_CAPABILITIES bits are not architectural contrary to what
     the SDM claims. !@#%$^!

   - Add Tremont CPU models to the split lock detection cpu match.

   - Add a missing static attribute to make sparse happy"

* tag 'x86-urgent-2020-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/split_lock: Add Tremont family CPU models
  x86/split_lock: Bits in IA32_CORE_CAPABILITIES are not architectural
  x86/resctrl: Preserve CDP enable over CPU hotplug
  x86/resctrl: Fix invalid attempt at removing the default resource group
  x86/split_lock: Update to use X86_MATCH_INTEL_FAM6_MODEL()
  x86/umip: Make umip_insns static
  x86/microcode/AMD: Increase microcode PATCH_MAX_SIZE
  objtool: Make BP scratch register warning more robust
  objtool: Fix switch table detection in .text.unlikely
  objtool: Support Clang non-section symbols in ORC generation
  objtool: Support Clang non-section symbols in ORC dump
  objtool: Fix CONFIG_UBSAN_TRAP unreachable warnings

Pull time namespace fix from Thomas Gleixner:
 "An update for the proc interface of time namespaces: Use symbolic
  names instead of clockid numbers. The usability nuisance of numbers
  was noticed by Michael when polishing the man page"

* tag 'timers-urgent-2020-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  proc, time/namespace: Show clock symbolic names in /proc/pid/timens_offsets

Pull perf tooling fixes and updates from Thomas Gleixner:

 - Fix the header line of perf stat output for '--metric-only --per-socket'

 - Fix the python build with clang

 - The usual tools UAPI header synchronization

* tag 'perf-urgent-2020-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools headers: Synchronize linux/bits.h with the kernel sources
  tools headers: Adopt verbatim copy of compiletime_assert() from kernel sources
  tools headers: Update x86's syscall_64.tbl with the kernel sources
  tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
  tools headers UAPI: Update tools's copy of drm.h headers
  tools headers kvm: Sync linux/kvm.h with the kernel sources
  tools headers UAPI: Sync linux/fscrypt.h with the kernel sources
  tools include UAPI: Sync linux/vhost.h with the kernel sources
  tools arch x86: Sync asm/cpufeatures.h with the kernel sources
  tools headers UAPI: Sync linux/mman.h with the kernel
  tools headers UAPI: Sync sched.h with the kernel
  tools headers: Update linux/vdso.h and grab a copy of vdso/const.h
  perf stat: Fix no metric header if --per-socket and --metric-only set
  perf python: Check if clang supports -fno-semantic-interposition
  tools arch x86: Sync the msr-index.h copy with the kernel sources

Pull irq fixes from Thomas Gleixner:
 "A set of fixes/updates for the interrupt subsystem:

   - Remove setup_irq() and remove_irq(). All users have been converted
     so remove them before new users surface.

   - A set of bugfixes for various interrupt chip drivers

   - Add a few missing static attributes to address sparse warnings"

* tag 'irq-urgent-2020-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/irq-bcm7038-l1: Make bcm7038_l1_of_init() static
  irqchip/irq-mvebu-icu: Make legacy_bindings static
  irqchip/meson-gpio: Fix HARDIRQ-safe -> HARDIRQ-unsafe lock order
  irqchip/sifive-plic: Fix maximum priority threshold value
  irqchip/ti-sci-inta: Fix processing of masked irqs
  irqchip/mbigen: Free msi_desc on device teardown
  irqchip/gic-v4.1: Update effective affinity of virtual SGIs
  irqchip/gic-v4.1: Add support for VPENDBASER's Dirty+Valid signaling
  genirq: Remove setup_irq() and remove_irq()

Pull scheduler fixes from Thomas Gleixner:
 "Two fixes for the scheduler:

   - Work around an uninitialized variable warning where GCC can't
     figure it out.

   - Allow 'isolcpus=' to skip unknown subparameters so that older
     kernels work with the commandline of a newer kernel. Improve the
     error output while at it"

* tag 'sched-urgent-2020-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/vtime: Work around an unitialized variable warning
  sched/isolation: Allow "isolcpus=" to skip unknown sub-parameters

Pull RCU fix from Thomas Gleixner:
 "A single bugfix for RCU to prevent taking a lock in NMI context"

* tag 'core-urgent-2020-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rcu: Don't acquire lock in NMI handler in rcu_nmi_enter_common()

Pull ext4 fixes from Ted Ts'o:
 "Miscellaneous bug fixes and cleanups for ext4, including a fix for
  generic/388 in data=journal mode, removing some BUG_ON's, and cleaning
  up some compiler warnings"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: convert BUG_ON's to WARN_ON's in mballoc.c
  ext4: increase wait time needed before reuse of deleted inode numbers
  ext4: remove set but not used variable 'es' in ext4_jbd2.c
  ext4: remove set but not used variable 'es'
  ext4: do not zeroout extents beyond i_disksize
  ext4: fix return-value types in several function comments
  ext4: use non-movable memory for superblock readahead
  ext4: use matching invalidatepage in ext4_writepage

Pull cifs fixes from Steve French:
 "Three small smb3 fixes: two debug related (helping network tracing for
  SMB2 mounts, and the other removing an unintended debug line on
  signing failures), and one fixing a performance problem with 64K
  pages"

* tag '5.7-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: remove overly noisy debug line in signing errors
  cifs: improve read performance for page size 64KB & cache=strict & vers=2.1+
  cifs: dump the session id and keys also for SMB2 sessions

Merge tag 'flexible-array-member-5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux

Pull flexible-array member conversion from Gustavo Silva:
 "The current codebase makes use of the zero-length array language
  extension to the C90 standard, but the preferred mechanism to declare
  variable-length types such as these ones is a flexible array
  member[1][2], introduced in C99:

    struct foo {
        int stuff;
        struct boo array[];
    };

  By making use of the mechanism above, we will get a compiler warning
  in case the flexible array does not occur last in the structure, which
  will help us prevent some kind of undefined behavior bugs from being
  inadvertently introduced[3] to the codebase from now on.

  Also, notice that, dynamic memory allocations won't be affected by
  this change:

   "Flexible array members have incomplete type, and so the sizeof
    operator may not be applied. As a quirk of the original
    implementation of zero-length arrays, sizeof evaluates to zero."[1]

  sizeof(flexible-array-member) triggers a warning because flexible
  array members have incomplete type[1]. There are some instances of
  code in which the sizeof operator is being incorrectly/erroneously
  applied to zero-length arrays and the result is zero. Such instances
  may be hiding some bugs. So, this work (flexible-array member
  convertions) will also help to get completely rid of those sorts of
  issues.

  Notice that all of these patches have been baking in linux-next for
  quite a while now and, 238 more of these patches have already been
  merged into 5.7-rc1.

  There are a couple hundred more of these issues waiting to be
  addressed in the whole codebase"

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")

* tag 'flexible-array-member-5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux: (28 commits)
  xattr.h: Replace zero-length array with flexible-array member
  uapi: linux: fiemap.h: Replace zero-length array with flexible-array member
  uapi: linux: dlm_device.h: Replace zero-length array with flexible-array member
  tpm_eventlog.h: Replace zero-length array with flexible-array member
  ti_wilink_st.h: Replace zero-length array with flexible-array member
  swap.h: Replace zero-length array with flexible-array member
  skbuff.h: Replace zero-length array with flexible-array member
  sched: topology.h: Replace zero-length array with flexible-array member
  rslib.h: Replace zero-length array with flexible-array member
  rio.h: Replace zero-length array with flexible-array member
  posix_acl.h: Replace zero-length array with flexible-array member
  platform_data: wilco-ec.h: Replace zero-length array with flexible-array member
  memcontrol.h: Replace zero-length array with flexible-array member
  list_lru.h: Replace zero-length array with flexible-array member
  lib: cpu_rmap: Replace zero-length array with flexible-array member
  irq.h: Replace zero-length array with flexible-array member
  ihex.h: Replace zero-length array with flexible-array member
  igmp.h: Replace zero-length array with flexible-array member
  genalloc.h: Replace zero-length array with flexible-array member
  ethtool.h: Replace zero-length array with flexible-array member
  ...

Pull SCSI fixes from James Bottomley:
 "Seven fixes: three in target, one on a sg error leg, two in qla2xxx
  fixing warnings introduced in the last merge window and updating
  MAINTAINERS and one in hisi_sas fixing a problem introduced by libata"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: sg: add sg_remove_request in sg_common_write
  scsi: target: tcmu: reset_ring should reset TCMU_DEV_BIT_BROKEN
  scsi: target: fix PR IN / READ FULL STATUS for FC
  scsi: target: Write NULL to *port_nexus_ptr if no ISID
  scsi: MAINTAINERS: Update qla2xxx FC-SCSI driver maintainer
  scsi: qla2xxx: Fix regression warnings
  scsi: hisi_sas: Fix build error without SATA_HOST

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>