Conversion of int-gpios into interrupts property requires also
interrupt-parent and uses different flags.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On LS1088A, watchdog clk are divided by 16, correct it in dts.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a pwm-fan mapped to the PWM channel 0 which is connected to the
fan connector of the carrier.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Now that we have support for GPIO lines of the SMARC connector, enable
LED support on the KBox A-230-LS. There are two LEDs without fixed
functions, one is yellow and one is green. Unfortunately, it is just one
multi-color LED, thus while it is possible to enable both at the same
time it is hard to tell the difference between "yellow only" and "yellow
and green".
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Now that we have support for GPIO lines of the SMARC connector, map the
sleep, power and lid switch signals to the corresponding keys using the
gpio-keys and gpio-keys-polled drivers. The power and sleep signals have
dedicated interrupts, thus we use these ones. The lid switch is just
mapped to a GPIO input and needs polling.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the board management controller node.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx8mq-evk has a MIPI DSI port that can be used to connect a Raydium
RM67191 panel.

Add support for it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add label to pcie nodes so that they are easy to
refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a basic DTS for Variscite Symphony evaluation kit with VAR-SOM-MX8MN
(i.MX 8M Nano) System on Module.  This brings up the board with basic
functionalities although still few issues remain (e.g. I2C3 and USB OTG
port, although it might not be the problem of DTS).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add DTSI of Variscite VAR-SOM-MX8MN (Nano) System on Module in a basic
version, delivered with Variscite Symphony Evaluation kit.  This version
comes with:
- 1 GB of RAM,
- 16 GB eMMC,
- Gigabit Ethernet PHY,
- 802.11 ac/a/b/g/n WiFi with 4.2 Bluetooth,
- CAN bus,
- Audio codec (not yet configured in DTSI).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The pin configuration for PMIC interrupt is already set by
imx8mn-evk.dtsi with exactly the same values.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Symphony board uses GPIO from expander as Ethernet PHY reset pin,
not the GPIO1_IO9.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i2c3 clock frequency and pin configuration are already set by
imx8mm-var-som.dtsi.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The gpioledgrp in iomux is not used, so it can be dropped.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The ti,tps6598x binding requires interrupt-names property.  The driver
does not really use it but the hardware could have more interrupt lines
connected.  This fixes dtbs_check warning:

  arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dt.yaml: usb-pd@3f: 'interrupt-names' is a required property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 'interrupt-names' property is not described in dtschema, not used by
the driver and does not really make sense as its value is simple 'irq'.
Drop it to fix dtbs_check warnings like:

  arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dt.yaml:
    pmic@4b: 'interrupt-names' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Device tree schema expects regulator names to be lowercase.  This fixes
dtbs_check warnings like:

  pmic@4b: regulators:LDO1:regulator-name:0: 'LDO1' does not match '^ldo[1-7]$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX General Power Controller v2 device node was missing interrupts
property necessary to route its interrupt to GIC.  This also fixes the
dbts_check warnings like:

  arch/arm64/boot/dts/freescale/imx8mq-evk.dt.yaml: gpc@303a0000:
    {'compatible': ... '$nodename': ['gpc@303a0000']} is not valid under any of the given schemas
  arch/arm64/boot/dts/freescale/imx8mq-evk.dt.yaml: gpc@303a0000: 'interrupts' is a required property

Fixes: fdbcc04d ("arm64: dts: imx8mq: add GPC power domains")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

  ... 'usdhc3grp-100mhz', 'usdhc3grp-200mhz' do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The int-gpios was deprecated in favor of generic interrupts property.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The ROHM BD71847 PMIC has a 32.768 kHz clock.  Adding necessary parent
allows to probe the bd718x7 clock driver fixing boot errors:

    bd718xx-clk bd71847-clk.1.auto: No parent clk found
    bd718xx-clk: probe of bd71847-clk.1.auto failed with error -22
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Device tree schema expects regulator names to be lowercase.  Changing to
lowercase has multiple effects:
1. LDO6 supply is now properly configured, because regulator driver
   looks for supplies by lowercase name,
2. User-visible names via sysfs or debugfs are now lowercase,
2. dtbs_check warnings are fixed:

    pmic@4b: regulators:LDO1:regulator-name:0: 'LDO1' does not match '^ldo[1-6]$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The ROHM BD71847 PMIC has a 32.768 kHz clock.  Adding necessary parent
allows to probe the bd718x7 clock driver fixing boot errors:

    bd718xx-clk bd71847-clk.1.auto: No parent clk found
    bd718xx-clk: probe of bd71847-clk.1.auto failed with error -22
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Device tree schema expects pin configuration groups to end with 'grp'
suffix.  This fixes dtbs_check warnings like:

  pinctrl@30330000: 'pcal6414-gpio', 'pmicirq', 'usdhc1grp100mhz', 'usdhc1grp200mhz', 'usdhc1grpgpio',
    'usdhc2grp100mhz', 'usdhc2grp200mhz', 'usdhc2grpgpio', 'usdhc3grp100mhz', 'usdhc3grp200mhz'
    do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the board dts support for i.MX8MM DDR4 EVK board.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There are two type of i.MX8MM EVK board, one is populated with
LPDDR4(default dts), and one is populated with DDR4. these two
boards share most of the board design, but still have some difference.
imx8mm-evk has emmc support, imx8mm-ddr4-evk has gpmi nand support.
And also, the BT/WIFI module is different. So move the common dts
part into imx8mm-evk.dtsi for reuse.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PMIC node can be a clock provider (for its 32 kHz clock) and authors
of imx8mq-librem5-devkit.dts apparently wanted this because they added
input clock and clock-output-names.

Add necessary clock-cells to the PMIC node.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-and-tested-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SP805 binding sets the order of the clock-names to be: "wdog_clk",
"apb_pclk" (in exactly that order).

Change the order in the DTs for Freescale platforms to match that. The
two clocks given in all nodes are actually the same, so that does not
change any behaviour.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a DTS for Variscite Symphony evaluation kit with VAR-SOM-MX8MM
System on Module.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add DTSI of Variscite VAR-SOM-MX8MM System on Module in a basic version,
delivered with Variscite Symphony Evaluation kit.  This version comes
with:
 - 2 GB of RAM,
 - 16 GB eMMC,
 - Gigabit Ethernet PHY,
 - 802.11 ac/a/b/g/n WiFi with 4.2 Bluetooth (Cypress CYW43353),
 - CAN bus,
 - Audio codec (not yet configured in DTSI).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>