The KSZ8021 and KSZ8031 support RMII reference input clocks of 25MHz
and 50MHz. Both PHYs differ in the default frequency they expect
after reset. If this differs from the actual input clock, then
register 0x1f bit 7 must be changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch addresses a kernel unaligned access bug seen on a sparc64 system
with an igb adapter.  Specifically the __skb_flow_get_ports was returning a
be32 pointer which was then having the value directly returned.

In order to prevent this it is actually easier to simply not populate the
ports or address values when an skb is not present.  In this case the
assumption is that the data isn't needed and rather than slow down the
faster aligned accesses by making them have to assume the unaligned path on
architectures that don't support efficent unaligned access it makes more
sense to simply switch off the bits that were copying the source and
destination address/port for the case where we only care about the protocol
types and lengths which are normally 16 bit fields anyway.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. sk_run_filter has been renamed, sk_filter() is using SK_RUN_FILTER.
2. Remove wrong comments about storing intermediate value.
3. replace sk_run_filter with __bpf_prog_run for check_load_and_stores's
comments

Cc: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__sk_run_filter has been renamed as __bpf_prog_run, so replace them in comments
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jason Baron says:

====================
macvlan: optimize receive path

So after porting this optimization to net-next, I found that the netperf
results of TCP_RR regress right at the maximum peak of transactions/sec. That
is as I increase the number of threads via the first argument to super_netperf,
the number of transactions/sec keep increasing, peak, and then start
decreasing. It is right at the peak, that I see a small regression with this
patch (see results in patch 2/2).

Without the patch, the ksoftirqd threads are the top cpu consumers threads on
the system, since the extra 'netif_rx()', is queuing more softirq work, whereas
with the patch, the ksoftirqd threads are below all of the 'netserver' threads
in terms of their cpu usage. So there appears to be some interaction between how
softirqs are serviced at the peak here and this patch. I think the test results
are still supportive of this approach, but I wanted to be clear on my findings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The netif_rx() call on the fast path of macvlan_handle_frame() appears to
be there to ensure that we properly throttle incoming packets. However, it
would appear as though the proper throttling is already in place for all
possible ingress paths, and that the call is redundant. If packets are arriving
from the physical NIC, we've already throttled them by this point. Otherwise,
if they are coming via macvlan_queue_xmit(), it calls either
'dev_forward_skb()', which ends up calling netif_rx_internal(), or else in
the broadcast case, we are throttling via macvlan_broadcast_enqueue().

The test results below are from off the box to an lxc instance running macvlan.
Once the tranactions/sec stop increasing, the cpu idle time has gone to 0.
Results are from a quad core Intel E3-1270 V2@3.50GHz box with bnx2x 10G card.

for i in {10,100,200,300,400,500};
do super_netperf $i -H $ip -t TCP_RR; done
Average of 5 runs.

trans/sec 		 trans/sec
(3.17-rc7-net-next)      (3.17-rc7-net-next + this patch)
----------               ----------
208101                   211534 (+1.6%)
839493                   850162 (+1.3%)
845071                   844053 (-.12%)
816330                   819623 (+.4%)
778700                   789938 (+1.4%)
735984                   754408 (+2.5%)
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass last argument to macvlan_count_rx() as the correct bool type.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Iyappan Subramanian says:

====================
Add 10GbE support to APM X-Gene SoC ethernet driver

Adding 10GbE support to APM X-Gene SoC ethernet driver.

v4: Address comments from v3
* dtb: resolved merge conflict for the net tree

v3: Address comments from v2
* dtb: changed to use all-zeros for the mac address

v2: Address comments from v1
* created preparatory patch to review before adding new functionality
* dtb: updated to use tabs consistently

v1:
* Initial version
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Added 10GbE support
- Removed unused macros/variables
- Moved mac_init call to the end of hardware init
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Rearranged code to pave the way for adding 10GbE support
- Added mac_ops structure containing function pointers for mac specific functions
- Added port_ops structure containing function pointers for port specific functions
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added 10GbE interface and clock nodes.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Updated APM X-Gene ethernet driver maintainers list.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

minimal configurations where EPOLL, PERF_EVENTS, etc are disabled,
but NET is enabled, are failing to build with link error:
kernel/built-in.o: In function `bpf_prog_load':
syscall.c:(.text+0x3b728): undefined reference to `anon_inode_getfd'

fix it by selecting ANON_INODES when NET is enabled
Reported-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net-next

This batch contains two fixes for what you have in your net-next,
they are:

1) Remove nf_send_reset6() from header file. This function now resides
   in the nf_reject_ipv6 module. Reported by Eric Dumazet.

2) Fix wrong NFT_REJECT_ICMPX_MAX definition and adjust code to fix
   errors reported by Dan Carpenter's static analysis tools.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'master-2014-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next

John W. Linville says:

====================
pull request: wireless-next 2014-10-09

Please pull this batch of fixes intended for the 3.18 stream!

Andrea Merello makes rtl818x_pci use a more reasonable transmission
rate for HW generated frames.

Fabian Frederick tweaks some kernel-doc bits to avoid warnings.

Larry Finger corrects a possible unaligned access in the rtlwifi code.

Marek Puzyniak avoids a kernel panic in ath9k_hw_reset.

Sujith Manoharan goes for the hat trick -- he fixes a smatch warning
in the shared ath code, he fixes a crash in ath9k, and he corrects
a sequence number assignment problem in ath9k too.

For ease of merging, I pulled the last bits of the wireless tree as well...

Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Testing revealed that the local variable mc_filter was dimensioned
incorrectly for all possible configurations and get_mac_addr should
have been set_mac_addr (a typo). Make sure mc_filter is dimensioned
to 8 32-bit unsigned longs - the largest size of the Synopsys
multicast filter register set.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `rxq_deinit':
pxa168_eth.c:(.text+0x2a2f2e): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `txq_reclaim':
pxa168_eth.c:(.text+0x2a3044): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `txq_deinit':
pxa168_eth.c:(.text+0x2a310a): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `txq_init':
pxa168_eth.c:(.text+0x2a3226): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `rxq_init':
pxa168_eth.c:(.text+0x2a32d4): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `init_hash_table':
pxa168_eth.c:(.text+0x2a3354): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `rxq_refill':
pxa168_eth.c:(.text+0x2a345a): undefined reference to `dma_map_single'
drivers/built-in.o: In function `rxq_process':
pxa168_eth.c:(.text+0x2a39cc): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `pxa168_eth_remove':
pxa168_eth.c:(.text+0x2a3b84): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `pxa168_eth_start_xmit':
pxa168_eth.c:(.text+0x2a3e8a): undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The latest linus git tip (3.18-rc1) fails with the following build failure. Fix
this by making PTP support explicit for fm10k driver.

rivers/built-in.o: In function `fm10k_ptp_register':
(.text+0x12e760): undefined reference to `ptp_clock_registER'
drivers/built-in.o: In function `fm10k_ptp_unregister':
(.text+0x12e7dc): undefined reference to `ptp_clock_unregister'
Makefile:930: recipe for target 'vmlinux' failed
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[linux-devel:devel-hourly-2014100909 3763/3915] drivers/net/ethernet/freescale/fs_enet/mac-scc.c:119:32: error: 'SCCE_ENET_TXF' undeclared

Due to patch d43a396a net: fs_enet: Add NAPI TX, it appears that some target
compilations are broken.
This is due to the fact that unlike the FEC, the SCC and FCC don't have a TXF
event (complete Frame transmitted) but only TXB (buffer transmitted).
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Restore the quota fairness between qdisc's, that we broke with commit
5772e9a3 ("qdisc: bulk dequeue support for qdiscs with TCQ_F_ONETXQUEUE").

Before that commit, the quota in __qdisc_run() were in packets as
dequeue_skb() would only dequeue a single packet, that assumption
broke with bulk dequeue.

We choose not to account for the number of packets inside the TSO/GSO
packets (accessable via "skb_gso_segs").  As the previous fairness
also had this "defect". Thus, GSO/TSO packets counts as a single
packet.

Further more, we choose to slack on accuracy, by allowing a bulk
dequeue try_bulk_dequeue_skb() to exceed the "packets" limit, only
limited by the BQL bytelimit.  This is done because BQL prefers to get
its full budget for appropriate feedback from TX completion.

In future, we might consider reworking this further and, if it allows,
switch to a time-based model, as suggested by Eric. Right now, we only
restore old semantics.

Joint work with Eric, Hannes, Daniel and Jesper.  Hannes wrote the
first patch in cooperation with Daniel and Jesper.  Eric rewrote the
patch.

Fixes: 5772e9a3 ("qdisc: bulk dequeue support for qdiscs with TCQ_F_ONETXQUEUE")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: use mutex for hw settings

v2:
Make sure the autoresume wouldn't occur inside the mutex, otherwise
the dead lock would happen. For the purpose, adjust some code about
autosuspend/autoresume.

v1:
Use mutex to avoid that the serial hw settings would be interrupted
by other settings. Although there is no problem now, it makes the
driver more safe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the mutex to avoid the settings are interrupted by other ones.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add usb_autopm_xxx for rtl8152_get_settings() ,and remove
usb_autopm_xxx from read_mii_word() and write_mii_word().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Resume the device before setting the feature.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fix following warning.
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'header_len'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'data_len'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'max_page_order'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'errcode'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'gfp_mask'

Acutually the descriptions exist, but missing "@" in front.

This problem start to happen when following commit was merged
into Linus's tree during 3.18-rc1 merge period.
commit 2e4e4410
net: add alloc_skb_with_frags() helper
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
cxgb4/cxgb4vf: Misc fixes and 40G support for cxgb4vf

This patch series adds 40G support for cxgb4vf driver. Update the LSO length for
cxgb4vf, fix macro. Wait for device to get ready before reading PL_WHOAMI
register.

The patches series is created against 'net-next' tree.
And includes patches on cxgb4 and cxgb4vf driver.

We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Call t4_wait_dev_ready() before attempting to read the PL_WHOAMI register
(to determine which function we have been attached to). This prevents us from
failing on that read if it comes right after a RESET.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add 40G support for cxgb4vf driver. ethtool speed values are just numbers of
megabits and there is no SPEED_40000 in ethtool speed values. To be consistent,
use integer constants directly for all speeds.

Use is_x_10g_port()("is 10Gb/s or higher") in cfg_queues() instead of
is_10g_port() ("is exactly 10Gb/s"). Else we will end up using a single
"Queue Set" on 40Gb/s adapters.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the lso length for T5 adapter and fix PIDX_T5 macro
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Claudiu Manoil says:

====================
gianfar: ARM port driver updates (1/2)

This is the first round of driver portability fixes and clean-up
with the main purpose to make gianfar portable on ARM, for the ARM
based SoC that integrates the eTSEC ethernet controller - "ls1021a".
The patches primarily address compile time errors, when compiling
gianfar on ARM.  They replace PPC specific functions and macros
with architecture independent ones, solve arch specific header
inclusions, guard code that relates to PPC only, and even address
some simple endianess issues (see MAC address setup patch).
The patches addressing the bulk of remaining endianess issues,
like handling DMA fields (BD and FCB), will follow with the second
round.
====================
Reviewed-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace PPC specific eieio() with arch independent wmb()
for other architectures, i.e. ARM.
The eieio() macro is not defined on ARM and generates
build error.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use arch independent code to replace the powerpc dependent
spin_event_timeout() from gfar_halt_nodisable().
Added GRS/GTS read accessors to clean-up the implementation
of gfar_halt_nodisable().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the 32-bit memory access that is not endian safe,
i.e. not giving the desired byte layout for a LE CPU:
tempval = *((u32 *) (tmpbuf + 4)), where 'char tmpbuf[]'.

Get rid of rendundant local vars (tmpbuf[] and idx) and
forced casts.  Cleanup comments.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This excludes the PPC specific instructions for PPC based SoC
(MPC85xx family) version identification from ARM builds.
The PPC specific macro mfspr() from asm/reg.h is not defined
by the ARM architecture.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Include linux/of_address.h for of_iomap() and linux/of_irq.h
for irq_of_parse_and_map().

This wasn't an issue for PPC, because these were implicitly
included from asm/prom.h (via linux/of.h) for PPC builds only.
ARM builds need these includes explicitly.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

spin_event_timeout() is PPC dependent, use an arch independent
equivalent instead.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

in_be32()/out_be32() are not defined by ARM.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The UCC specific code included in fsl_pq_mdio.c (with
function calls from asm/ucc.h) is already guarded
by these config options, so this ARM build fix only
provides consistency with the rest UCC specific code.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>