Merge tag 'sunxi-dt-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt

Our usual bunch of patches to support the Allwinner SoCs, this time
adding:
  - DT fixes spotted through the schemas
  - Mali Support for the A10s/A13/GR8/R8
  - MMC improvements for the A64 and H6
  - New board: SL631 Action Camera, PineTab Early Adopter

* tag 'sunxi-dt-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (47 commits)
  ARM: dts: sunxi: Rename nmi_intc to r_intc
  ARM: dts: sun8i: h2-plus: bananapi-m2-zero: Increase BT UART speed
  ARM: dts: sunxi: bananapi-m2-plus: Increase BT UART speed
  arm64: dts: allwinner: pine-h64: Fix typos in BT GPIOs
  arm64: dts: allwinner: pinetab: Fix the panel compatible
  arm64: dts: allwinner: pinephone: Remove useless light sensor supplies
  arm64: dts: allwinner: h6: Use - instead of @ for DT OPP entries
  ARM: dts: sun8i-a33: sina33: Add missing panel power supply
  ARM: dts: sun8i-a83t: Remove empty CSI port
  ARM: dts: sun8i-s3: pinecube: Fix CSI DTC warnings
  ARM: dts: sun8i-s3: impetus: Fix the USB PHY ID detect GPIO properties
  ARM: dts: sun8i: nanopi-r1: Fix GPIO regulator state array
  ARM: dts: sun6i: primo81: Remove useless io-channel-cells
  ARM: dts: sunxi: Fix CPU thermal zone node name
  ARM: dts: sunxi: Add missing backlight supply
  ARM: dts: sunxi: Fix the LED node names
  dt-bindings: rtc: sun6i-a31-rtc: Loosen the requirements on the clocks
  dt-bindings: iio: adc: Add AXP803 compatible
  dt-bindings: sunxi: Fix the pinecube compatible
  ARM: dts: sun8i-v3s: Add CSI0 MCLK pin definition
  ...

Link: https://lore.kernel.org/r/48511540-fdd6-4fbe-8037-ec9fa8436147.lettre@localhostSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'ti-k3-dt-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux into arm/dt

Devicetree changes for TI K3 platforms for v5.12 merge window:

- Common fixups: PMU compatible, MMC dtbs_check warnings squelch

- J7200: R5F, PCIe, SERDES support

- J721E: PCIE fixups

* tag 'ti-k3-dt-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux:
  arm64: dts: ti: k3*: Fixup PMU compatibility to be CPU specific
  arm64: dts: ti: k3: mmc: fix dtbs_check warnings
  arm64: dts: ti: k3-j7200-som-p0: Add DDR carveout memory nodes for R5Fs
  arm64: dts: ti: k3-j7200-som-p0: Add mailboxes to R5Fs
  arm64: dts: ti: k3-j7200: Add R5F cluster nodes
  arm64: dts: ti: k3-j7200-common-proc-board: Enable PCIe
  arm64: dts: ti: k3-j7200-common-proc-board: Enable SERDES0
  arm64: dts: ti: k3-j7200-main: Add PCIe device tree node
  arm64: dts: ti: k3-j7200-main: Add SERDES and WIZ device tree node
  arm64: dts: ti: k3-j721e-main: Remove "syscon" nodes added for pcieX_ctrl
  arm64: dts: ti: k3-j721e-main: Fix supported max outbound regions

Link: https://lore.kernel.org/r/20210130131422.yvq2edxfongys7x5@pendantSigned-off-by: Arnd Bergmann <arnd@arndb.de>

The R_INTC block controls more than just the NMI, and it is a different
hardware block than the NMI INTC found in some other Allwinner SoCs, so
the label "nmi_intc" is inaccurate. Name it "r_intc" to match the
compatible and to match the few references in the vendor documentation.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210118055040.21910-6-samuel@sholland.org

Bluetooth module on BananaPi M2 Zero can also be used for streaming
audio. However, for that case higher UART speed is required.

Add a max-speed property.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210116103710.245617-1-jernej.skrabec@siol.net

Bluetooth module on BananaPi M2 Plus can also be used for streaming
audio. However, for that case higher UART speed is required.

Add a max-speed property.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210116105228.847073-1-jernej.skrabec@siol.net

The commit 53441b8e ("arm64: dts: allwinner: h6: PineH64 model B:
Add bluetooth") introduced the Bluetooth chip for the PineH64 model B,
but the GPIOs property didn't conform to the binding of the bluetooth
chip. Let's fix this.

Fixes: 53441b8e ("arm64: dts: allwinner: h6: PineH64 model B: Add bluetooth")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-19-maxime@cerno.tech

The commit 7fa40ca7 ("arm64: allwinner: dts: a64: add DT for Early
Adopter's PineTab") introduced an ili9881-based panel device node but
didn't conform to the binding. Fix this.

Fixes: 7fa40ca7 ("arm64: allwinner: dts: a64: add DT for Early Adopter's PineTab")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-18-maxime@cerno.tech

The stk3311 binding don't expect a vdd or leda power supplies. Remove
them.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-17-maxime@cerno.tech

DTC and the dt-validate tools report warnings for opp with the format
opp@$frequency: dtc for a missing reg property, and dt-validate since
the binding requires child nodes to have the format opp-$frequency.

Change this to the latter format.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-16-maxime@cerno.tech

The SinA33 panel is missing its power-supply property, even though the
binding mandates it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-15-maxime@cerno.tech

The empty CSI port triggers a dt-validate warning. Let's align with the
other DTSI and remove it entirely, expecting the DTS to fill it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-14-maxime@cerno.tech

Our CSI endpoint trigger some DTC warnings due to the fact that we're
having a single endpoint that doesn't need any reg property, and since
we don't have a reg property, we don't need the address-cells and
size-cells properties anymore.

Fix those
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-13-maxime@cerno.tech

While the USB PHY Device Tree mandates that the name of the ID detect pin
should be usb0_id_det-gpios, a significant number of device tree use
usb0_id_det-gpio instead.

This was functional because the GPIO framework falls back to the gpio
suffix that is legacy, but we should fix this.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-12-maxime@cerno.tech

Even though it translates to the same thing down to the binary level, we
should have an array of 2 number cells to describe each voltage state,
which in turns create a validation warning.

Let's fix this.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-11-maxime@cerno.tech

The mma8452 binding doesn't expect an io-channel-cells property, let's
remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-10-maxime@cerno.tech

Merge tag 'tegra-for-5.12-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt

dt-bindings: tegra: Changes for v5.12-rc1

Exposed a new QSPI clock to DT on Tegra210 and documents the eMMC SKU of
the Jetson Xavier NX board.

* tag 'tegra-for-5.12-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  dt-bindings: arm: tegra: Document Jetson Xavier NX eMMC SKU

Link: https://lore.kernel.org/r/20210129193254.3610492-2-thierry.reding@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'tegra-for-5.12-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt

arm64: tegra: Device tree changes for v5.12-rc1

Fixes an issue with HDA codec detection by properly wiring up the
power-domain for the HDA controller. This also fixes one of the USB-C
ports on Jetson AGX Xavier and enables support for audio on various
Tegra210, Tegra186 and Tegra194 boards. The Jetson Nano and Jetson TX1
also gain QSPI support.

* tag 'tegra-for-5.12-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  arm64: tegra: Audio graph sound card for Jetson AGX Xavier
  arm64: tegra: Audio graph sound card for Jetson TX2
  Revert "arm64: tegra: Disable the ACONNECT for Jetson TX2"
  arm64: tegra: Add RT5658 device entry
  arm64: tegra: Add support for Jetson Xavier NX with eMMC
  arm64: tegra: Prepare for supporting the Jetson Xavier NX with eMMC
  arm64: tegra: Enable QSPI on Jetson Xavier NX
  arm64: tegra: Add QSPI nodes on Tegra194
  arm64: tegra: Enable QSPI on Jetson Nano
  arm64: tegra: Audio graph sound card for Jetson Nano and TX1
  arm64: tegra: Audio graph header for Tegra210
  arm64: tegra: Order nodes alphabetically on Tegra210
  arm64: tegra: Enable Jetson-Xavier J512 USB host
  arm64: tegra: Add XUSB pad controller's "nvidia,pmc" property on Tegra210
  arm64: tegra: Add power-domain for Tegra210 HDA
  dt-bindings: clock: tegra: Add clock ID TEGRA210_CLK_QSPI_PM

Link: https://lore.kernel.org/r/20210129193254.3610492-5-thierry.reding@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'tegra-for-5.12-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt

ARM: tegra: Device tree changes for v5.12-rc1

Fixes the pinmux configuration for the eMMC on the Ouya to fix issues
with certain bootloaders.

* tag 'tegra-for-5.12-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: ouya: Fix eMMC on specific bootloaders

Link: https://lore.kernel.org/r/20210129193254.3610492-3-thierry.reding@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Enable support for audio-graph based sound card on Jetson AGX Xavier.
Following I/O interfaces are enabled.
  * I2S1, I2S2, I2S4 and I2S6
  * DMIC3
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Enable support for audio-graph based sound card on Jetson TX2. Based
on the board design following I/O modules are enabled.
  * All I2S instances (I2S1 ... I2S6)
  * All DSPK instances (DSPK1, DSPK2)
  * DMIC1, DMIC2 and DMIC3
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This reverts commit fb319496 ("arm64: tegra: Disable the
ACONNECT for Jetson TX2").
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Jetson AGX Xavier has an on-board audio codec whicn is connected to
Tegra I2S1 interface. Hence add corresponding device node for the
audio codec.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Ouya fails to detect the eMMC module when booted via certain bootloaders.
Fastboot and hard-kexec bootloaders fail while u-boot does not. It was
discovered that the issue manifests if the sdmmc4 alternate configuration
clock pin is input disabled.

Ouya uses sdmmc4 in the primary pin configuration. It is unknown why this
occurs, though it is likely related to other eMMC limitations experienced
on Ouya.

For now, fix it by enabling input on cam_mclk_pcc0.

Fixes: d7195ac5 ("ARM: tegra: Add device-tree for Ouya")
Reported-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Two different SKUs exist for the Jetson Xavier NX module, so document
the compatible strings for both, as well as the developer kits that come
with each of the SKUs.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Merge tag 'omap-for-v5.12/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt

Devicetree changes for omaps for v5.12 merge window

This includes the following earlier patches that were considered too
late for v5.11 as discussed between Arnd and me on freenode #armlinux
in December:

- More updates to use cpsw switchdev driver

- Enable gta04 PMIC power management

- Updates for dra7 for ECC support, 1.8GHz speed and keep the
  ldo0 regulator always on as specified in the data manual

And then we have the new devicetree changes:

- Configure the original Amazon Echo to for audio

- Configure missing thermal interrupt for omap4430

- Configure mapphone devices for passive thermal cooling, and add
  1.2GHz mode.

- Correct omap4430 sgx clock rate to use the runtime Android kernel
  value, the earlier value was for a lower power operating point

- Drop turbo mode for 1GHz omap3 variants as we now have passive
  cooling configured

- Update email address for Javier

- Add new MYIR Tech Limited board support

* tag 'omap-for-v5.12/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am335x-myirtech-*: Add DT for AM335X MYIR Tech Limited board
  ARM: dts: omap3-igep: Change email address in copyright notice
  ARM: dts: omap36xx: Remove turbo mode for 1GHz variants
  ARM: dts: omap443x: Correct sgx clock to 307.2MHz as used on motorola vendor kernel
  ARM: dts: motorola-mapphone: Add 1.2GHz OPP
  ARM: dts: motorola-mapphone: Configure lower temperature passive cooling
  ARM: dts: Configure missing thermal interrupt for 4430
  ARM: dts: omap3-echo: Add speaker sound card support
  ARM: dts: dra71-evm: mark ldo0 regulator as always on
  ARM: dts: dra76x: add support for OPP_PLUS
  ARM: dts: am574x-idk: add support for EMIF1 ECC
  ARM: dts: omap3-gta04: fix twl4030-power settings
  ARM: dts: am335x-evm/evmsk/icev2: switch to new cpsw switch drv
  ARM: dts: am33xx-l4: add dt node for new cpsw switchdev driver

Link: https://lore.kernel.org/r/pull-1611845066-809577@atomide.com-2Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'stm32-dt-for-v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt

STM32 DT updates for v5.12, round 1

Highlights:
----------

MCU part:
 -Rename mmc nodes to match with yaml validation.

MPU part:
 -Rename mmc nodes to match with yaml validation.
 -Move vdda1v1 & vdda1v8 (used by usbphyc) from boards files
  to SoC dtsi file.

 -LXA:
  -Fix leds schema for yaml validation.

 -DH:
  -Enable SDMMC1 internal pull-ups and disable CKIN feedabck clock
   on DHCOM.
  -Add SDMMC1 init state inorder to use some gpios during probing phase.
  -Disable KS8851 and FMC on PicoITX board.

* tag 'stm32-dt-for-v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
  ARM: dts: stm32: add #clock-cells property to usbphyc node on stm32mp151
  ARM: dts: stm32: remove usbphyc ports vdda1v1 & vdda1v8 on stm32mp15 boards
  ARM: dts: stm32: add usbphyc vdda1v1 and vdda1v8 supplies on stm32mp151
  ARM: dts: stm32: Add STM32MP1 I2C6 SDA/SCL pinmux
  ARM: dts: stm32: Rename mmc controller nodes to mmc@
  ARM: dts: stm32: Enable voltage translator auto-detection on DHCOM
  ARM: dts: stm32: Add additional init state for SDMMC1 pins
  ARM: dts: stm32: Disable KS8851 and FMC on PicoITX board
  ARM: dts: stm32: Fix schema warnings for pwm-leds on lxa-mc1
  ARM: dts: stm32: Disable SDMMC1 CKIN feedback clock on DHCOM
  ARM: dts: stm32: Enable internal pull-ups for SDMMC1 on DHCOM SoM
  ARM: dts: stm32: Fix GPIO hog flags on DHCOM DRC02
  ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
  ARM: dts: stm32: Fix GPIO hog names on DHCOM
  ARM: dts: stm32: Disable optional TSC2004 on DRC02 board
  ARM: dts: stm32: Disable WP on DHCOM uSD slot
  ARM: dts: stm32: Connect card-detect signal on DHCOM
  ARM: dts: stm32: Fix polarity of the DH DRC02 uSD card detect

Link: https://lore.kernel.org/r/5e8897a0-8f68-5e41-bfa0-ccdf1e23a3c1@foss.st.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-arm-dt-for-v5.12-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas ARM DT updates for v5.12 (take two)

  - Increase support (SPI, I2C, Ethernet, Serial, MMC) for the R-Car V3U
    SoC on the Renesas Falcon board,
  - Disable SD functions for plain eMMC,
  - A minor fix.

* tag 'renesas-arm-dt-for-v5.12-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  arm64: dts: renesas: beacon: Fix EEPROM compatible value
  arm64: dts: renesas: falcon: Enable MMC
  arm64: dts: renesas: r8a779a0: Add MMC node
  arm64: dts: renesas: r8a779a0: Add HSCIF support
  arm64: dts: renesas: falcon: Complete SCIF0 nodes
  arm64: dts: renesas: r8a779a0: Add & update SCIF nodes
  arm64: dts: renesas: falcon: Add Ethernet-AVB0 support
  arm64: dts: renesas: r8a779a0: Add Ethernet-AVB support
  arm64: dts: renesas: falcon: Add I2C0,1,6 support
  arm64: dts: renesas: r8a779a0: Add I2C nodes
  arm64: dts: renesas: Disable SD functions for plain eMMC
  arm64: dts: renesas: r8a779a0: Add MSIOF device nodes

Link: https://lore.kernel.org/r/20210129090815.2552425-2-geert+renesas@glider.beSigned-off-by: Arnd Bergmann <arnd@arndb.de>

ARM64: DT: Hisilicon ARM64 DT updates for 5.12

- Further cleanups of the hisilicon DTS to align with the dtschema
- Add or update the I2C, pinctrl and reset nodes for Hikey970

* tag 'hisi-arm64-dt-for-5.12v2' of git://github.com/hisilicon/linux-hisi:
  arm64: dts: hisilicon: hi3670.dtsi: add I2C settings
  arm64: dts: hisilicon: hikey970-pinctrl.dtsi: add missing pinctrl settings
  arm64: dts: hisilicon: hi3670.dtsi: add iomcu_rst
  arm64: dts: hisilicon: delete unused property smmu-cb-memtype
  arm64: dts: hisilicon: avoid irrelevant nodes being mistakenly identified as PHY nodes
  arm64: dts: hisilicon: normalize the node name of the localbus
  arm64: dts: hisilicon: normalize the node name of the module thermal
  arm64: dts: hisilicon: place clock-names "bus" before "core"
  arm64: dts: hisilicon: separate each group of data in the property "ranges"

Link: https://lore.kernel.org/r/6013D1C7.90902@hisilicon.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

The I2C buses are not declared at the device tree. As this will
be needed by further patches, add them, keeping all in
disabled state. Per-board settings can override it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

There are several pinctrl settings that are missing at this
DT file.

Also, the entries are out of order.

Add the missing bits, as they'll be required by the DRM driver - and
probably by other drivers not upstreamed yet.

Reorder the entres, adding the missing bits.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

This is required in order to support USB.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

The "smmu-cb-memtype" is a private property developed by the Hisilicon
driver in the early stage and is not used now. So delete it.

Otherwise, below YAML check warnings are reported:
arch/arm64/boot/dts/hisilicon/hip06-d03.dt.yaml: iommu@a0040000: \
'smmu-cb-memtype' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/hisilicon/hip07-d05.dt.yaml: iommu@a0040000: \
'smmu-cb-memtype' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

Currently, the names of several nodes incorrectly match common PHY
provider schema. And the phy-provider.yaml requires them must have
property "#phy-cells". As a result, false positives similar to the
following are reported:
usb2-phy@120: '#phy-cells' is a required property

Change their names slightly so that they do not match pattern:
"^(|usb-|usb2-|usb3-|pci-|pcie-|sata-)phy(@[0-9a-f,]+)*$".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

Change the node name of the localbus to match
'^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'. This error
is detected by simple-bus.yaml.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

1. Change the node name of the thermal zone to match
'^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', add suffix "-thermal".
2. Change the node name of the trip point to match
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', delete character "@".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

Look at the clock-names schema defined in arm,mali-utgard.yaml:
clock-names:
  items:
    - const: bus
    - const: core

The "bus" needs to be placed before the "core".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

Do not write the "ranges" of multiple groups of data into a uint32 array,
use <> to separate them. Otherwise, the errors similar to the following
will be reported:

soc: pcie@a0090000:ranges: [[33554432, 0, 2986344448, 0, 2986344448, 0, \
100597760, 16777216, 0, 0, 0, 3086942208, 0, 65536]] is not valid under \
any of the given schemas (Possible causes of the failure):
soc: pcie@a0090000:ranges: [[33554432, 0, 2986344448, 0, 2986344448, 0, \
100597760, 16777216, 0, 0, 0, 3086942208, 0, 65536]] is not of type 'boolean'
soc: pcie@a0090000:ranges:0: [33554432, 0, 2986344448, 0, 2986344448, 0, \
100597760, 16777216, 0, 0, 0, 3086942208, 0, 65536] is too long
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

usbphyc is a 48Mhz clock provider: the clock can be used as clock source
for USB OTG. Add #clock-cells property to usbphyc node to reflect this
capability.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

vdda1v1 and vdda1v8 supplies are required by USB PLL, not by the PHYs.
Remove them from usbphyc child phy nodes now that they are managed in
usbphyc parent node at SoC level.

Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

vdda1v1 and vdda1v8 supplies are required by USB PLL. Add them in usbphyc
node.

Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>