McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.

Fixes: 1f7226a5 ("arm64: dts: ti: k3-am625-beagleplay: Add HDMI support")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-4-8c317dabdd0a@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.

Fixes: c00504ea ("arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-3-8c317dabdd0a@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.

Fixes: 4a2c5ddd ("arm64: dts: ti: k3-am62a7-sk: Enable audio on AM62A")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-2-8c317dabdd0a@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.

Fixes: b94b4371 ("arm64: dts: ti: Enable audio on SK-AM62(-LP)")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-1-8c317dabdd0a@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add device tree overlay to enable both ICSSG1 ports available on AM64x-EVM
in MII mode.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20240429092919.657629-1-danishanwar@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

A PRU system event "vring" has been added to each PRU and RTU
node in each of the ICSSG0, ICSSG1 and ICSSG2 remote processor
subsystems to enable the virtio/rpmsg communication between MPU
and that PRU/RTU core. The additions are done in the base
k3-am65-main.dtsi, and so are inherited by all the K3 AM65x
boards.

The PRU system events is the preferred approach over using TI
mailboxes, as it eliminates an external peripheral access from
the PRU/RTU-side, and keeps the interrupt generation internal to
the ICSSG. The difference from MPU would be minimal in using one
versus the other.

Mailboxes can still be used if desired, but currently there is
no support on firmware-side for K3 SoCs to use mailboxes. Either
approach would require that an appropriate firmware image is
loaded/booted on the PRU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240529064420.571615-3-danishanwar@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

PRU system events "vring" have been added to each PRU and RTU node
in each of the ICSSG0 and ICSSG1 remote processor subsystems to
enable the virtio/rpmsg communication between MPU and that PRU/RTU core.
No events have been added to the Tx_PRU cores at present. The
additions are done in the base k3-am64main.dtsi, and so are inherited
by all the K3 AM64x boards.

The PRU system events is the preferred approach over using TI
mailboxes, as it eliminates an external peripheral access from
the PRU/RTU-side, and keeps the interrupt generation internal to
the ICSSG. The difference from MPU would be minimal in using one
versus the other.

Mailboxes can still be used if desired, but currently there is
no support on firmware-side for K3 SoCs to use mailboxes. Either
approach would require that an appropriate firmware image is
loaded/booted on the PRU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240529064420.571615-2-danishanwar@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add Tulip TPS62873 nodes for J784S4 EVM. These are step-down regulators
that supply VDD_CPU_AVS and VDD_CORE_0V8 to the SoC.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20240528040159.3919652-4-n-francis@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add DTS node for two TPS6287x high current buck convertors.

The two TPS6287x supply power to the MAIN domain for AVS and other core
supplies.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20240528040159.3919652-3-n-francis@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add DTS node for LP87334E PMIC and two TPS6287x high current buck
converters.

LP87334E is responsible for supplying power to the MCU and MAIN domains
as well as to LPDDR4. The two TPS6287x supply power to the MAIN
domain for AVS and other core supplies.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://www.ti.com/lit/pdf/slda060
Link: https://lore.kernel.org/r/20240528040159.3919652-2-n-francis@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The board uses SERDES0 Lane 3 for USB3 IP. So update the
SerDes lane info for USB. Add the pin mux data and
enable USB3 support.
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # k3-j784s4-evm
Link: https://lore.kernel.org/r/20240507095545.8210-3-r-gunasekaran@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add support for the USB 3.0 controller
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # k3-j784s4-evm
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240507095545.8210-2-r-gunasekaran@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

CAN instances 0 and 1 in the mcu domain and 16 in the main domain are
brought on the evm through headers J42, J43 and J46 respectively. Thus,
add their respective transceiver's 0, 1 and 2 dt nodes to add support
for these CAN instances.

CAN instance 4 in the main domain is brought on the evm through header
J45. The CAN High and Low lines from the SoC are routed through a mux
on the evm. The select lines need to be set for the CAN signals to
reach to its transceiver on the evm. Therefore, add transceiver 3
dt node to add support for this CAN instance.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240411201747.18697-1-b-kapoor@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

On-chip RTC is used as a wakeup source on am62a board designs. This
patch removes the disabled status property to enable the RTC node.
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20240429184445.14876-1-vibhore@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

CAN instance 0 in the mcu domain is brought on the J721E-SK board
through header J1. Thus, add its respective transceiver 1 dt node to add
support for this CAN instance.

CAN instances 0, 5 and 9 in the main domain are brought on the J721E-SK
board through headers J5, J6 and J2 respectively. Thus, add their
respective transceivers 2, 3 and 4 dt nodes to add support for these CAN
instances.
Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
Reviewed-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240430131512.1327283-1-b-padhi@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

J722S does not pin out all of the GPIO same as AM62P and have
more number of GPIO on the main_gpio1 instance. Fix the GPIO
count on both instances by overriding the ti,ngpio property.

Fixes: ea55b933 ("arm64: dts: ti: Introduce J722S family of SoCs")

More details at J722S/AM67 Datasheet (Section 5.3.11, GPIO):
	https://www.ti.com/lit/ds/symlink/am67.pdfSigned-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20240507103332.167928-1-vaishnav.a@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add the bootph-all property to the memory node so that it can be
accessed by FDT functions at bootloader stage.

The bootloader requires the memory node to be able to initialize and set
the size of the DRAM banks. For this purpose, make sure all memory nodes
are present and standardized, and modify them if not.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20240506110203.3230255-1-n-francis@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The RS485 transceiver RE (Receiver enable) and DE (Driver enable) are
shorted and connected to both RTS/CTS of the SoC UART.
RE is active-low, DE is active-high.

Remove the "rs485-rts-active-low" flag to match RTS polarity with DE,
and fix communication in both transmit and receive directions.

Fixes: d60483fa ("arm64: dts: add description for solidrun am642 som and evaluation board")
Signed-off-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/r/20240504-ti-rs485-rts-v1-1-e88ef1c96f34@solid-run.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add a PMIC node to the phycore-am64 device tree.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240429195830.4027250-2-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

For main_pktdma node, the TX Channel Realtime Register region 'tchanrt'
is 128KB and Ring Realtime Register region 'ringrt' is 2MB as shown in
memory map in the TRM[0] (Table 2-1).
So fix ranges for those register regions.

[0]: <https://www.ti.com/lit/pdf/spruj83>

Fixes: b5080c7c ("arm64: dts: ti: k3-am62p: Add nodes for more IPs")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240430105253.203750-4-j-choudhary@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

For main_pktdma node, the TX Channel Realtime Register region 'tchanrt'
is 128KB and Ring Realtime Register region 'ringrt' is 2MB as shown in
memory map in the TRM[0] (Table 2-1).
So fix ranges for those register regions.

[0]: <https://www.ti.com/lit/pdf/spruj16>

Fixes: 3dad70de ("arm64: dts: ti: k3-am62a-main: Add more peripheral nodes")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240430105253.203750-3-j-choudhary@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

For main_pktdma node, the TX Channel Realtime Register region 'tchanrt'
is 128KB and Ring Realtime Register region 'ringrt' is 2MB as shown in
memory map in the TRM[0] (Table 2-1).
So fix ranges for those register regions.

[0]: <https://www.ti.com/lit/pdf/spruiv7>

Fixes: c37c58fd ("arm64: dts: ti: k3-am62: Add more peripheral nodes")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240430105253.203750-2-j-choudhary@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The CPSW9G instance of the CPSW Ethernet Switch supports USXGMII mode
with MAC Ports 1 and 2 of the instance, which are connected to ENET
Expansion 1 and ENET Expansion 2 slots on the EVM respectively, through
the Serdes2 instance of the SERDES.

Enable CPSW9G MAC Ports 1 and 2 in fixed-link configuration USXGMII mode
at 5 Gbps each.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-6-c-vankar@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

The J7 Quad Port Add-On Ethernet Card for J784S4 EVM supports
QSGMII mode. Use the overlay to configure CPSW9G ports in QSGMII
mode with the Add-On Ethernet Card connected to the ENET Expansion
1 slot on the EVM.

Add support to reset the PHY from kernel by using gpio-hog and
gpio-reset.

Add aliases for CPSW9G ports to enable kernel to fetch MAC Addresses
directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-5-c-vankar@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Enable MAIN CPSW2G and add alias for it to enable Linux to fetch
MAC Address for the port directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-4-c-vankar@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

J784S4 SoC has MAIN CPSW2G and CPSW9G instances of the CPSW
Ethernet Switch. CPSW2G has 1 external port and 1 host port
while CPSW9G has 8 external ports and 1 host port.

Add device-tree nodes for MAIN CPSW2G and CPSW9G and disable
them by default. MAIN CPSW2G will be enabled in the board file
while device-tree overlays will be used to enable CPSW9G.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-3-c-vankar@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add alias for the MCU CPSW2G port to enable Linux to fetch MAC Address
for the port directly from U-Boot.
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-2-c-vankar@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add missing bootph-all property for CPSW MAC's PHY node
phy_gmii_sel.
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240430085048.3143665-1-c-vankar@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

percpu.h depends on smp.h, but doesn't include it directly because of
circular header dependency issues; percpu.h is needed in a bunch of low
level headers.

This fixes a randconfig build error on mips:

  include/linux/alloc_tag.h: In function '__alloc_tag_ref_set':
  include/asm-generic/percpu.h:31:40: error: implicit declaration of function 'raw_smp_processor_id' [-Werror=implicit-function-declaration]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 24e44cc2 ("mm: percpu: enable per-cpu allocation tagging")
Closes: https://lore.kernel.org/oe-kbuild-all/202405210052.DIrMXJNz-lkp@intel.com/Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools

Pull perf tool fix from Arnaldo Carvalho de Melo:
 "Revert a patch causing a regression.

  This made a simple 'perf record -e cycles:pp make -j199' stop working
  on the Ampere ARM64 system Linus uses to test ARM64 kernels".

* tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
  Revert "perf parse-events: Prefer sysfs/JSON hardware events over legacy"

This reverts commit 617824a7.

This made a simple 'perf record -e cycles:pp make -j199' stop working on
the Ampere ARM64 system Linus uses to test ARM64 kernels, as discussed
at length in the threads in the Link tags below.

The fix provided by Ian wasn't acceptable and work to fix this will take
time we don't have at this point, so lets revert this and work on it on
the next devel cycle.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Cc: Ethan Adams <j.ethan.adams@gmail.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Tycho Andersen <tycho@tycho.pizza>
Cc: Yang Jihong <yangjihong@bytedance.com>
Link: https://lore.kernel.org/lkml/CAHk-=wi5Ri=yR2jBVk-4HzTzpoAWOgstr1LEvg_-OXtJvXXJOA@mail.gmail.com
Link: https://lore.kernel.org/lkml/CAHk-=wiWvtFyedDNpoV7a8Fq_FpbB+F5KmWK2xPY3QoYseOf_A@mail.gmail.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Pull smb client fixes from Steve French:

 - two important netfs integration fixes - including for a data
   corruption and also fixes for multiple xfstests

 - reenable swap support over SMB3

* tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Fix missing set of remote_i_size
  cifs: Fix smb3_insert_range() to move the zero_point
  cifs: update internal version number
  smb3: reenable swapfiles over SMB3 mounts

Merge tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm

Pull misc fixes from Andrew Morton:
 "16 hotfixes, 11 of which are cc:stable.

  A few nilfs2 fixes, the remainder are for MM: a couple of selftests
  fixes, various singletons fixing various issues in various parts"

* tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
  mm/ksm: fix possible UAF of stable_node
  mm/memory-failure: fix handling of dissolved but not taken off from buddy pages
  mm: /proc/pid/smaps_rollup: avoid skipping vma after getting mmap_lock again
  nilfs2: fix potential hang in nilfs_detach_log_writer()
  nilfs2: fix unexpected freezing of nilfs_segctor_sync()
  nilfs2: fix use-after-free of timer for log writer thread
  selftests/mm: fix build warnings on ppc64
  arm64: patching: fix handling of execmem addresses
  selftests/mm: compaction_test: fix bogus test success and reduce probability of OOM-killer invocation
  selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
  selftests/mm: compaction_test: fix bogus test success on Aarch64
  mailmap: update email address for Satya Priya
  mm/huge_memory: don't unpoison huge_zero_folio
  kasan, fortify: properly rename memintrinsics
  lib: add version into /proc/allocinfo output
  mm/vmalloc: fix vmalloc which may return null if called with __GFP_NOFAIL

Pull irq fixes from Ingo Molnar:

 - Fix x86 IRQ vector leak caused by a CPU offlining race

 - Fix build failure in the riscv-imsic irqchip driver
   caused by an API-change semantic conflict

 - Fix use-after-free in irq_find_at_or_after()

* tag 'irq-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/irqdesc: Prevent use-after-free in irq_find_at_or_after()
  genirq/cpuhotplug, x86/vector: Prevent vector leak during CPU offline
  irqchip/riscv-imsic: Fixup riscv_ipi_set_virq_range() conflict

Pull x86 fixes from Ingo Molnar:

 - Fix regressions of the new x86 CPU VFM (vendor/family/model)
   enumeration/matching code

 - Fix crash kernel detection on buggy firmware with
   non-compliant ACPI MADT tables

 - Address Kconfig warning

* tag 'x86-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Fix x86_match_cpu() to match just X86_VENDOR_INTEL
  crypto: x86/aes-xts - switch to new Intel CPU model defines
  x86/topology: Handle bogus ACPI tables correctly
  x86/kconfig: Select ARCH_WANT_FRAME_POINTERS again when UNWINDER_FRAME_POINTER=y

Pull ipmi updates from Corey Minyard:
 "Mostly updates for deprecated interfaces, platform.remove and
  converting from a tasklet to a BH workqueue.

  Also use HAS_IOPORT for disabling inb()/outb()"

* tag 'for-linus-6.10-1' of https://github.com/cminyard/linux-ipmi:
  ipmi: kcs_bmc_npcm7xx: Convert to platform remove callback returning void
  ipmi: kcs_bmc_aspeed: Convert to platform remove callback returning void
  ipmi: ipmi_ssif: Convert to platform remove callback returning void
  ipmi: ipmi_si_platform: Convert to platform remove callback returning void
  ipmi: ipmi_powernv: Convert to platform remove callback returning void
  ipmi: bt-bmc: Convert to platform remove callback returning void
  char: ipmi: handle HAS_IOPORT dependencies
  ipmi: Convert from tasklet to BH workqueue

Pull ceph updates from Ilya Dryomov:
 "A series from Xiubo that adds support for additional access checks
  based on MDS auth caps which were recently made available to clients.

  This is needed to prevent scenarios where the MDS quietly discards
  updates that a UID-restricted client previously (wrongfully) acked to
  the user.

  Other than that, just a documentation fixup"

* tag 'ceph-for-6.10-rc1' of https://github.com/ceph/ceph-client:
  doc: ceph: update userspace command to get CephFS metadata
  ceph: add CEPHFS_FEATURE_MDS_AUTH_CAPS_CHECK feature bit
  ceph: check the cephx mds auth access for async dirop
  ceph: check the cephx mds auth access for open
  ceph: check the cephx mds auth access for setattr
  ceph: add ceph_mds_check_access() helper
  ceph: save cap_auths in MDS client when session is opened

Pull ntfs3 updates from Konstantin Komarov:
 "Fixes:
   - reusing of the file index (could cause the file to be trimmed)
   - infinite dir enumeration
   - taking DOS names into account during link counting
   - le32_to_cpu conversion, 32 bit overflow, NULL check
   - some code was refactored

  Changes:
   - removed max link count info display during driver init

  Remove:
   - atomic_open has been removed for lack of use"

* tag 'ntfs3_for_6.10' of https://github.com/Paragon-Software-Group/linux-ntfs3:
  fs/ntfs3: Break dir enumeration if directory contents error
  fs/ntfs3: Fix case when index is reused during tree transformation
  fs/ntfs3: Mark volume as dirty if xattr is broken
  fs/ntfs3: Always make file nonresident on fallocate call
  fs/ntfs3: Redesign ntfs_create_inode to return error code instead of inode
  fs/ntfs3: Use variable length array instead of fixed size
  fs/ntfs3: Use 64 bit variable to avoid 32 bit overflow
  fs/ntfs3: Check 'folio' pointer for NULL
  fs/ntfs3: Missed le32_to_cpu conversion
  fs/ntfs3: Remove max link count info display during driver init
  fs/ntfs3: Taking DOS names into account during link counting
  fs/ntfs3: remove atomic_open
  fs/ntfs3: use kcalloc() instead of kzalloc()

Pull smb server fixes from Steve French:
 "Two ksmbd server fixes, both for stable"

* tag '6.10-rc-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
  ksmbd: ignore trailing slashes in share paths
  ksmbd: avoid to send duplicate oplock break notifications