Main goal is to reuse the same functions in VSI config and rebuild
paths.
To do this split ice_vsi_setup into smaller pieces and reuse it during
rebuild.

ice_vsi_alloc() should only alloc memory, not set the default values
for VSI.
Move setting defaults to separate function. This will allow config of
already allocated VSI, for example in reload path.

The path is mostly moving code around without introducing new
functionality. Functions ice_vsi_cfg() and ice_vsi_decfg() were
added, but they are using code that already exist.

Use flag to pass information about VSI initialization during rebuild
instead of using boolean value.
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Do few small cleanups:

1) Rename the function to reflect that it doesn't configure all things
related to VSI. ice_vsi_cfg_lan() better fits to what function is doing.

ice_vsi_cfg() can be use to name function that will configure whole VSI.

2) Remove unused ethtype field from VSI. There is no need to set
ethtype here, because it is never used.

3) Remove unnecessary check for ICE_VSI_CHNL. There is check for
ICE_VSI_CHNL in ice_vsi_get_qs, so there is no need to check it before
calling the function.

4) Simplify ice_vsi_alloc() call. There is no need to check the type of
VSI before calling ice_vsi_alloc(). For ICE_VSI_CHNL vf is always NULL
(ice_vsi_setup() is called with vf=NULL).
For ICE_VSI_VF or ICE_VSI_CTRL ch is always NULL and for other VSI types
ch and vf are always NULL.

5) Remove unnecessary call to ice_vsi_dis_irq(). ice_vsi_dis_irq() will
be called in ice_vsi_close() flow (ice_vsi_close() -> ice_vsi_down() ->
ice_vsi_dis_irq()). Remove unnecessary call.

6) Don't remove specific filters in release. All hw filters are removed
in ice_fltr_remove_alli(), which is always called in VSI release flow.
There is no need to remove only ethertype filters before calling
ice_fltr_remove_all().

7) Rename ice_vsi_clear() to ice_vsi_free(). As ice_vsi_clear() only
free memory allocated in ice_vsi_alloc() rename it to ice_vsi_free()
which better shows what function is doing.

8) Free coalesce param in rebuild. There is potential memory leak if
configuration of VSI lan fails. Free coalesce to avoid it.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Use xa_array instead of deprecated ida to alloc id for RDMA aux driver.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Simplify probe flow by moving all RDMA related code to ice_init_rdma().
Unroll irq allocation if RDMA initialization fails.

Implement ice_deinit_rdma() and use it in remove flow.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Frank Sae says:

====================
net: add dts for yt8521 and yt8531s, add driver for yt8531

Add dts for yt8521 and yt8531s, add driver for yt8531.
 These patches have been verified on our AM335x platform (motherboard)
 which has one integrated yt8521 and one RGMII interface.
 It can connect to daughter boards like yt8531s or yt8531 board.

 v5:
 - change the compatible of yaml
 - change the maintainers of yaml from "frank sae" to "Frank Sae"

 v4:
 - change default tx delay from 150ps to 1950ps
 - add compatible for yaml

 v3:
 - change default rx delay from 1900ps to 1950ps
 - moved ytphy_rgmii_clk_delay_config_with_lock from yt8521's patch to yt8531's patch
 - removed unnecessary checks of phydev->attached_dev->dev_addr

 v2:
 - split BIT macro as one patch
 - split "dts for yt8521/yt8531s ... " patch as two patches
 - use standard rx-internal-delay-ps and tx-internal-delay-ps, removed motorcomm,sds-tx-amplitude
 - removed ytphy_parse_dt, ytphy_probe_helper and ytphy_config_init_helper
 - not store dts arg to yt8521_priv
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have
 verified the driver on AM335x platform with yt8531 board. On the
 board, yt8531 gigabit ethernet phy works in utp mode, RGMII
 interface, supports 1000M/100M/10M speeds, and wol(magic package).
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add dts support for Motorcomm yt8531s gigabit ethernet phy.
 Change yt8521_probe to support clk config of yt8531s. Becase
 yt8521_probe does the things which yt8531s is needed, so
 removed yt8531s function.
 This patch has been verified on AM335x platform with yt8531s board.
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add dts support for Motorcomm yt8521 gigabit ethernet phy.
 Add ytphy_rgmii_clk_delay_config function to support dst config for
 the delay of rgmii clk. This funciont is common for yt8521, yt8531s
 and yt8531.
 This patch has been verified on AM335x platform.
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add BIT macro for Motorcomm yt8521/yt8531 gigabit ethernet phy.
 This is a preparatory patch. Add BIT macro for 0xA012 reg, and
 supplement for 0xA001 and 0xA003 reg. These will be used to support dts.
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a YAML binding document for the Motorcomm yt8xxx Ethernet phy.
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vlad Buslov says:

====================
net: Allow offloading of UDP NEW connections via act_ct

Currently only bidirectional established connections can be offloaded
via act_ct. Such approach allows to hardcode a lot of assumptions into
act_ct, flow_table and flow_offload intermediate layer codes. In order
to enabled offloading of unidirectional UDP NEW connections start with
incrementally changing the following assumptions:

- Drivers assume that only established connections are offloaded and
  don't support updating existing connections. Extract ctinfo from meta
  action cookie and refuse offloading of new connections in the drivers.

- Fix flow_table offload fixup algorithm to calculate flow timeout
  according to current connection state instead of hardcoded
  "established" value.

- Add new flow_table flow flag that designates bidirectional connections
  instead of assuming it and hardcoding hardware offload of every flow
  in both directions.

- Add new flow_table flow flag that designates connections that are
  offloaded to hardware as "established" instead of assuming it. This
  allows some optimizations in act_ct and prevents spamming the
  flow_table workqueue with redundant tasks.

With all the necessary infrastructure in place modify act_ct to offload
UDP NEW as unidirectional connection. Pass reply direction traffic to CT
and promote connection to bidirectional when UDP connection state
changes to "assured". Rely on refresh mechanism to propagate connection
state change to supporting drivers.

Note that early drop algorithm that is designed to free up some space in
connection tracking table when it becomes full (by randomly deleting up
to 5% of non-established connections) currently ignores connections
marked as "offloaded". Now, with UDP NEW connections becoming
"offloaded" it could allow malicious user to perform DoS attack by
filling the table with non-droppable UDP NEW connections by sending just
one packet in single direction. To prevent such scenario change early
drop algorithm to also consider "offloaded" connections for deletion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Both synchronous early drop algorithm and asynchronous gc worker completely
ignore connections with IPS_OFFLOAD_BIT status bit set. With new
functionality that enabled UDP NEW connection offload in action CT
malicious user can flood the conntrack table with offloaded UDP connections
by just sending a single packet per 5tuple because such connections can no
longer be deleted by early drop algorithm.

To mitigate the issue allow both early drop and gc to consider offloaded
UDP connections for deletion.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify the offload algorithm of UDP connections to the following:

- Offload NEW connection as unidirectional.

- When connection state changes to ESTABLISHED also update the hardware
flow. However, in order to prevent act_ct from spamming offload add wq for
every packet coming in reply direction in this state verify whether
connection has already been updated to ESTABLISHED in the drivers. If that
it the case, then skip flow_table and let conntrack handle such packets
which will also allow conntrack to potentially promote the connection to
ASSURED.

- When connection state changes to ASSURED set the flow_table flow
NF_FLOW_HW_BIDIRECTIONAL flag which will cause refresh mechanism to offload
the reply direction.

All other protocols have their offload algorithm preserved and are always
offloaded as bidirectional.

Note that this change tries to minimize the load on flow_table add
workqueue. First, it tracks the last ctinfo that was offloaded by using new
flow 'NF_FLOW_HW_ESTABLISHED' flag and doesn't schedule the refresh for
reply direction packets when the offloads have already been updated with
current ctinfo. Second, when 'add' task executes on workqueue it always
update the offload with current flow state (by checking 'bidirectional'
flow flag and obtaining actual ctinfo/cookie through meta action instead of
caching any of these from the moment of scheduling the 'add' work)
preventing the need from scheduling more updates if state changed
concurrently while the 'add' work was pending on workqueue.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently tcf_ct_flow_table_fill_actions() function assumes that only
established connections can be offloaded and always sets ctinfo to either
IP_CT_ESTABLISHED or IP_CT_ESTABLISHED_REPLY strictly based on direction
without checking actual connection state. To enable UDP NEW connection
offload set the ctinfo, metadata cookie and NF_FLOW_HW_ESTABLISHED
flow_offload flags bit based on ct->status value.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify flow table offload to cache the last ct info status that was passed
to the driver offload callbacks by extending enum nf_flow_flags with new
"NF_FLOW_HW_ESTABLISHED" flag. Set the flag if ctinfo was 'established'
during last act_ct meta actions fill call. This infrastructure change is
necessary to optimize promoting of UDP connections from 'new' to
'established' in following patches in this series.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify flow table offload to support unidirectional connections by
extending enum nf_flow_flags with new "NF_FLOW_HW_BIDIRECTIONAL" flag. Only
offload reply direction when the flag is set. This infrastructure change is
necessary to support offloading UDP NEW connections in original direction
in following patches in series.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently flow_offload_fixup_ct() function assumes that only replied UDP
connections can be offloaded and hardcodes UDP_CT_REPLIED timeout value. To
enable UDP NEW connection offload in following patches extract the actual
connections state from ct->status and set the timeout according to it.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to offload connections in other states besides "established" the
driver offload callbacks need to have access to connection conntrack info.
Flow offload intermediate representation data structure already contains
that data encoded in 'cookie' field, so just reuse it in the drivers.

Reject offloading IP_CT_NEW connections for now by returning an error in
relevant driver callbacks based on value of ctinfo. Support for offloading
such connections will need to be added to the drivers afterwards.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable debugfs for vcap for lan966x. This will allow to print all the
entries in the VCAP and also the port information regarding which keys
are configured.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yoshihiro Shimoda says:

====================
net: renesas: rswitch: Modify initialization for SERDES and PHY

- My platform has the 88x2110.
- The MACTYPE setting of strap pin on the platform is SXGMII.
- However, we realized that the SoC cannot communicate the PHY with SXGMII
  because of mismatching hardware specification.
- We have a lot of boards which mismatch the MACTYPE setting.

So, I would like to change the MACTYPE as SGMII by software for the platform.

The patch [1/5] sets phydev->host_interfaces by phylink for Marvell PHY
driver (marvell10g) to initialize the MACTYPE.

- The patch [1/5] siplifies the rswitch driver.
- The patch [2/5] converts to phy_device from phylink.
- The patch [3/5] sets phydev->host_interfaces from this driver without
  any new functions of phylib.
- The patch [4/5] adds phy_power_on() calling to initialize the Ethernet
  SERDES PHY driver (r8a779f0-eth-serdes) for each channel.
- The patch [5/5] adds "max-speed" handling.

Changes from v4:
https://lore.kernel.org/all/20230127142621.1761278-1-yoshihiro.shimoda.uh@renesas.com/
 - No modification of phylink API.
 - Convert to phylib instead of phylink.
 - Add "max-speed" handling.

Changes from v3:
https://lore.kernel.org/all/20230127014812.1656340-1-yoshihiro.shimoda.uh@renesas.com/
 - Keep a pointer of "port" and more simplify the code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous code set the speed by the interface mode of PHY.
Also this hardware has a restriction which cannot change the speed
at runtime. To use other speed, add "max-speed" handling to set
each port's speed if needed.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some Ethernet PHYs (like marvell10g) will decide the host interface
mode by the media-side speed. So, the rswitch driver needs to
initialize one of the Ethernet SERDES (r8a779f0-eth-serdes) ports
after linked the Ethernet PHY up. The r8a779f0-eth-serdes driver has
.init() for initializing all ports and .power_on() for initializing
each port. So, add phy_power_{on,off} calling for it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set phydev->host_interfaces before calling of_phy_connect() to
configure the PHY with the information of host_interfaces.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Intended to set phy_device->host_interfaces by phylink in the future.
But there is difficult to implement phylink properly, especially
supporting the in-band mode on this driver because extra initialization
is needed after linked the ethernet PHY up. So, convert to phy_device
from phylink.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify struct phy *serdes handling by keeping the valiable in
the struct rswitch_device.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the unlikely case incoming packets are dropped because
of IP_MINTTL / IPV6_MINHOPCOUNT constraints...
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230201174345.2708943-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Conversion to gpiod API done in commit 468ba54b ("fec: convert
to gpio descriptor") clashed with gpiolib applying the same quirk to the
reset GPIO polarity (introduced in commit b02c85c9). This results in
the reset line being left active/device being left in reset state when
reset line is "active low".

Remove handling of 'phy-reset-active-high' property from the driver and
rely on gpiolib to apply needed adjustments to avoid ending up with the
double inversion/flipped logic.

Fixes: 468ba54b ("fec: convert to gpio descriptor")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230201215320.528319-2-dmitry.torokhov@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Conversion of the driver to gpiod API done in 468ba54b ("fec:
convert to gpio descriptor") incorrectly made reset line mandatory and
resulted in aborting driver probe in cases where reset line was not
specified (note: this way of specifying PHY reset line is actually
deprecated).

Switch to using devm_gpiod_get_optional() and skip manipulating reset
line if it can not be located.

Fixes: 468ba54b ("fec: convert to gpio descriptor")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230201215320.528319-1-dmitry.torokhov@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

net/core/gro.c
  7d2c89b3 ("skb: Do mix page pool and page referenced frags in GRO")
  b1a78b9b ("net: add support for ipv4 big tcp")
https://lore.kernel.org/all/20230203094454.5766f160@canb.auug.org.au/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bpf, can and netfilter.

  Current release - regressions:

   - phy: fix null-deref in phy_attach_direct

   - mac802154: fix possible double free upon parsing error

  Previous releases - regressions:

   - bpf: preserve reg parent/live fields when copying range info,
     prevent mis-verification of programs as safe

   - ip6: fix GRE tunnels not generating IPv6 link local addresses

   - phy: dp83822: fix null-deref on DP83825/DP83826 devices

   - sctp: do not check hb_timer.expires when resetting hb_timer

   - eth: mtk_sock: fix SGMII configuration after phylink conversion

  Previous releases - always broken:

   - eth: xdp: execute xdp_do_flush() before napi_complete_done()

   - skb: do not mix page pool and page referenced frags in GRO

   - bpf:
      - fix a possible task gone issue with bpf_send_signal[_thread]()
      - fix an off-by-one bug in bpf_mem_cache_idx() to select the right
        cache
      - add missing btf_put to register_btf_id_dtor_kfuncs
      - sockmap: fon't let sock_map_{close,destroy,unhash} call itself

   - gso: fix null-deref in skb_segment_list()

   - mctp: purge receive queues on sk destruction

   - fix UaF caused by accept on already connected socket in exotic
     socket families

   - tls: don't treat list head as an entry in tls_is_tx_ready()

   - netfilter: br_netfilter: disable sabotage_in hook after first
     suppression

   - wwan: t7xx: fix runtime PM implementation

  Misc:

   - MAINTAINERS: spring cleanup of networking maintainers"

* tag 'net-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
  mtk_sgmii: enable PCS polling to allow SFP work
  net: mediatek: sgmii: fix duplex configuration
  net: mediatek: sgmii: ensure the SGMII PHY is powered down on configuration
  MAINTAINERS: update SCTP maintainers
  MAINTAINERS: ipv6: retire Hideaki Yoshifuji
  mailmap: add John Crispin's entry
  MAINTAINERS: bonding: move Veaceslav Falico to CREDITS
  net: openvswitch: fix flow memory leak in ovs_flow_cmd_new
  net: ethernet: mtk_eth_soc: disable hardware DSA untagging for second MAC
  virtio-net: Keep stop() to follow mirror sequence of open()
  selftests: net: udpgso_bench_tx: Cater for pending datagrams zerocopy benchmarking
  selftests: net: udpgso_bench: Fix racing bug between the rx/tx programs
  selftests: net: udpgso_bench_rx/tx: Stop when wrong CLI args are provided
  selftests: net: udpgso_bench_rx: Fix 'used uninitialized' compiler warning
  can: mcp251xfd: mcp251xfd_ring_set_ringparam(): assign missing tx_obj_num_coalesce_irq
  can: isotp: split tx timer into transmission and timeout
  can: isotp: handle wait_event_interruptible() return values
  can: raw: fix CAN FD frame transmissions over CAN XL devices
  can: j1939: fix errant WARN_ON_ONCE in j1939_session_deactivate
  hv_netvsc: Fix missed pagebuf entries in netvsc_dma_map/unmap()
  ...

Merge tag 'linux-kselftest-kunit-fixes-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull KUnit fixes from Shuah Khan:
 "Three fixes to bugs that cause kernel crash, link error during build,
  and a third to fix kunit_test_init_section_suites() extra indirection
  issue"

* tag 'linux-kselftest-kunit-fixes-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  kunit: fix kunit_test_init_section_suites(...)
  kunit: fix bug in KUNIT_EXPECT_MEMEQ
  kunit: Export kunit_running()

Pull ARM SoC fixes from Arnd Bergmann:
 "The majority of bugfixes is once more for the NXP i.MX platform,
  addressing issue with i.MX8M (UART, watchdog and ethernet) as well as
  imx8dxl power button and the USB modem on an imx7 board.

  The reason that i.MX always shows up here is obviously not that they
  are more buggy than the others, but they have the most boards and are
  good about getting fixes in quickly.

  The other DT fixes are for the Nuvoton wpcm450 flash controller and
  the i2c mux on an ASpeed board.

  Lastly, there are updates to the MAINTAINERS entries for Mediatek,
  AMD/Seattle and NXP SoCs, as well as a lone code fix for error
  handling in the allwinner 'rsb' bus driver"

* tag 'soc-fixes-6.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: dts: wpcm450: Add nuvoton,shm = <&shm> to FIU node
  MAINTAINERS: Update entry for MediaTek SoC support
  MAINTAINERS: amd: drop inactive Brijesh Singh
  ARM: dts: imx7d-smegw01: Fix USB host over-current polarity
  arm64: dts: imx8mm-verdin: Do not power down eth-phy
  MAINTAINERS: match freescale ARM64 DT directory in i.MX entry
  arm64: dts: imx8mm: Fix pad control for UART1_DTE_RX
  ARM: dts: aspeed: Fix pca9849 compatible
  arm64: dts: freescale: imx8dxl: fix sc_pwrkey's property name linux,keycode
  arm64: dts: imx8m-venice: Remove incorrect 'uart-has-rtscts'
  arm64: dts: imx8mm: Reinstate GPIO watchdog always-running property on eDM SBC
  bus: sunxi-rsb: Fix error handling in sunxi_rsb_init()

Pull s390 fixes from Heiko Carstens:

 - With CONFIG_VMAP_STACK enabled it is not possible to load the s390
   specific diag288_wdt watchdog module. The reason is that a pointer to
   a string is passed to an inline assembly; this string however is
   located on the stack, while the instruction within the inline
   assembly expects a physicial address. Fix this by copying the string
   to a kmalloc'ed buffer.

 - The diag288_wdt watchdog module does not indicate that it accesses
   memory from an inline assembly, which it does. Add "memory" to the
   clobber list to prevent the compiler from optimizing code incorrectly
   away.

 - Pass size of the uncompressed kernel image to __decompress() call.
   Otherwise the kernel image decompressor may corrupt/overwrite an
   initrd. This was reported to happen on s390 after commit 2aa14b1a
   ("zstd: import usptream v1.5.2").

* tag 's390-6.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/decompressor: specify __decompress() buf len to avoid overflow
  watchdog: diag288_wdt: fix __diag288() inline assembly
  watchdog: diag288_wdt: do not use stack buffers for hardware data

Merge tag 'platform-drivers-x86-v6.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull x86 platform driver fixes from Hans de Goede:
 "A set of AMD PMF fixes + a few other small fixes"

* tag 'platform-drivers-x86-v6.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
  platform/x86: touchscreen_dmi: Add Chuwi Vi8 (CWI501) DMI match
  platform/x86: thinkpad_acpi: Fix thinklight LED brightness returning 255
  platform/x86/amd: pmc: add CONFIG_SERIO dependency
  platform/x86/amd/pmf: Ensure mutexes are initialized before use
  platform/x86/amd/pmf: Fix to update SPS thermals when power supply change
  platform/x86/amd/pmf: Fix to update SPS default pprof thermals
  platform/x86/amd/pmf: update to auto-mode limits only after AMT event
  platform/x86/amd/pmf: Add helper routine to check pprof is balanced
  platform/x86/amd/pmf: Add helper routine to update SPS thermals

Bjørn Mork says:

====================
Fix mtk_eth_soc sgmii configuration.

This has been tested on a MT7986 with a Maxlinear GPY211C phy
permanently attached to the second SoC mac.
====================

Link: https://lore.kernel.org/r/20230201182331.943411-1-bjorn@mork.noSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently there is no IRQ handling (even the SGMII supports it).
Enable polling to support SFP ports.

Fixes: 14a44ab0 ("net: mtk_eth_soc: partially convert to phylink_pcs")
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
[ bmork: changed "1" => "true" ]
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The logic of the duplex bit is inverted.  Setting it means half
duplex, not full duplex.

Fix and rename macro to avoid confusion.

Fixes: 7e538372 ("net: ethernet: mediatek: Re-add support SGMII")
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The code expect the PHY to be in power down which is only true after reset.
Allow changes of the SGMII parameters more than once.

Only power down when reconfiguring to avoid bouncing the link when there's
no reason to - based on code from Russell King.

There are cases when the SGMII_PHYA_PWD register contains 0x9 which
prevents SGMII from working. The SGMII still shows link but no traffic
can flow. Writing 0x0 to the PHYA_PWD register fix the issue. 0x0 was
taken from a good working state of the SGMII interface.

Fixes: 42c03844 ("net-next: mediatek: add support for MediaTek MT7622 SoC")
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
[ bmork: rebased and squashed into one patch ]
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'linux-can-fixes-for-6.2-20230202' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
can 2023-02-02

The first patch is by Ziyang Xuan and removes a errant WARN_ON_ONCE()
in the CAN J1939 protocol.

The next 3 patches are by Oliver Hartkopp. The first 2 target the CAN
ISO-TP protocol and fix the state machine with respect to signals and
a regression found by the syzbot.

The last patch is by me an missing assignment during the ethtool ring
configuration callback.

* tag 'linux-can-fixes-for-6.2-20230202' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
  can: mcp251xfd: mcp251xfd_ring_set_ringparam(): assign missing tx_obj_num_coalesce_irq
  can: isotp: split tx timer into transmission and timeout
  can: isotp: handle wait_event_interruptible() return values
  can: raw: fix CAN FD frame transmissions over CAN XL devices
  can: j1939: fix errant WARN_ON_ONCE in j1939_session_deactivate
====================

Link: https://lore.kernel.org/r/20230202094135.2293939-1-mkl@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jakub Kicinski says:

====================
MAINTAINERS: spring refresh of networking maintainers

Use Jon Corbet's script for generating statistics about maintainer
coverage to identify inactive maintainers of relatively active code.
Move them to CREDITS.
====================

Link: https://lore.kernel.org/r/20230201182014.2362044-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>