Pull MIPS fixes from Thomas Bogendoerfer:

 - build fix for ZSTD enabled configs

 - fix for preempt warning

 - fix for loongson FTLB detection

 - fix for page table level selection

* tag 'mips-fixes_5.16_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: use 3-level pgtable for 64KB page size on MIPS_VA_BITS_48
  MIPS: loongson64: fix FTLB configuration
  MIPS: Fix using smp_processor_id() in preemptible in show_cpuinfo()
  MIPS: boot/compressed/: add __ashldi3 to target for ZSTD compression

Pull networking fixes from Jakub Kicinski:
 "Networking fixes, including fixes from netfilter.

  Current release - regressions:

   - r8169: fix incorrect mac address assignment

   - vlan: fix underflow for the real_dev refcnt when vlan creation
     fails

   - smc: avoid warning of possible recursive locking

  Current release - new code bugs:

   - vsock/virtio: suppress used length validation

   - neigh: fix crash in v6 module initialization error path

  Previous releases - regressions:

   - af_unix: fix change in behavior in read after shutdown

   - igb: fix netpoll exit with traffic, avoid warning

   - tls: fix splice_read() when starting mid-record

   - lan743x: fix deadlock in lan743x_phy_link_status_change()

   - marvell: prestera: fix bridge port operation

  Previous releases - always broken:

   - tcp_cubic: fix spurious Hystart ACK train detections for
     not-cwnd-limited flows

   - nexthop: fix refcount issues when replacing IPv6 groups

   - nexthop: fix null pointer dereference when IPv6 is not enabled

   - phylink: force link down and retrigger resolve on interface change

   - mptcp: fix delack timer length calculation and incorrect early
     clearing

   - ieee802154: handle iftypes as u32, prevent shift-out-of-bounds

   - nfc: virtual_ncidev: change default device permissions

   - netfilter: ctnetlink: fix error codes and flags used for kernel
     side filtering of dumps

   - netfilter: flowtable: fix IPv6 tunnel addr match

   - ncsi: align payload to 32-bit to fix dropped packets

   - iavf: fix deadlock and loss of config during VF interface reset

   - ice: avoid bpf_prog refcount underflow

   - ocelot: fix broken PTP over IP and PTP API violations

  Misc:

   - marvell: mvpp2: increase MTU limit when XDP enabled"

* tag 'net-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (94 commits)
  net: dsa: microchip: implement multi-bridge support
  net: mscc: ocelot: correctly report the timestamping RX filters in ethtool
  net: mscc: ocelot: set up traps for PTP packets
  net: ptp: add a definition for the UDP port for IEEE 1588 general messages
  net: mscc: ocelot: create a function that replaces an existing VCAP filter
  net: mscc: ocelot: don't downgrade timestamping RX filters in SIOCSHWTSTAMP
  net: hns3: fix incorrect components info of ethtool --reset command
  net: hns3: fix one incorrect value of page pool info when queried by debugfs
  net: hns3: add check NULL address for page pool
  net: hns3: fix VF RSS failed problem after PF enable multi-TCs
  net: qed: fix the array may be out of bound
  net/smc: Don't call clcsock shutdown twice when smc shutdown
  net: vlan: fix underflow for the real_dev refcnt
  ptp: fix filter names in the documentation
  ethtool: ioctl: fix potential NULL deref in ethtool_set_coalesce()
  nfc: virtual_ncidev: change default device permissions
  net/sched: sch_ets: don't peek at classes beyond 'nbands'
  net: stmmac: Disable Tx queues when reconfiguring the interface
  selftests: tls: test for correct proto_ops
  tls: fix replacing proto_ops
  ...

Current driver version is able to handle only one bridge at time.
Configuring two bridges on two different ports would end up shorting this
bridges by HW. To reproduce it:

	ip l a name br0 type bridge
	ip l a name br1 type bridge
	ip l s dev br0 up
	ip l s dev br1 up
	ip l s lan1 master br0
	ip l s dev lan1 up
	ip l s lan2 master br1
	ip l s dev lan2 up

	Ping on lan1 and get response on lan2, which should not happen.

This happened, because current driver version is storing one global "Port VLAN
Membership" and applying it to all ports which are members of any
bridge.
To solve this issue, we need to handle each port separately.

This patch is dropping the global port member storage and calculating
membership dynamically depending on STP state and bridge participation.

Note: STP support was broken before this patch and should be fixed
separately.

Fixes: c2e86691 ("net: dsa: microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20211126123926.2981028-1-o.rempel@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull ACPI fixes from Rafael Wysocki:
 "These fix a NULL pointer dereference in the CPPC library code and a
  locking issue related to printing the names of ACPI device nodes in
  the device properties framework.

  Specifics:

   - Fix NULL pointer dereference in the CPPC library code occuring on
     hybrid systems without CPPC support (Rafael Wysocki).

   - Avoid attempts to acquire a semaphore with interrupts off when
     printing the names of ACPI device nodes and clean up code on top of
     that fix (Sakari Ailus)"

* tag 'acpi-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: CPPC: Add NULL pointer check to cppc_get_perf()
  ACPI: Make acpi_node_get_parent() local
  ACPI: Get acpi_device's parent from the parent field

Pull power management fixes from Rafael Wysocki:
 "These address three issues in the intel_pstate driver and fix two
  problems related to hibernation.

  Specifics:

   - Make intel_pstate work correctly on Ice Lake server systems with
     out-of-band performance control enabled (Adamos Ttofari).

   - Fix EPP handling in intel_pstate during CPU offline and online in
     the active mode (Rafael Wysocki).

   - Make intel_pstate support ITMT on asymmetric systems with
     overclocking enabled (Srinivas Pandruvada).

   - Fix hibernation image saving when using the user space interface
     based on the snapshot special device file (Evan Green).

   - Make the hibernation code release the snapshot block device using
     the same mode that was used when acquiring it (Thomas Zeitlhofer)"

* tag 'pm-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM: hibernate: Fix snapshot partial write lengths
  PM: hibernate: use correct mode for swsusp_close()
  cpufreq: intel_pstate: ITMT support for overclocked system
  cpufreq: intel_pstate: Fix active mode offline/online EPP handling
  cpufreq: intel_pstate: Add Ice Lake server to out-of-band IDs

Pull fuse fix from Miklos Szeredi:
 "Fix a regression caused by a bugfix in the previous release. The
  symptom is a VM_BUG_ON triggered from splice to the fuse device.

  Unfortunately the original bugfix was already backported to a number
  of stable releases, so this fix-fix will need to be backported as
  well"

* tag 'fuse-fixes-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: release pipe buf after last use

Vladimir Oltean says:

====================
Fix broken PTP over IP on Ocelot switches

Changes in v2: added patch 5, added Richard's ack for the whole series
sans patch 5 which is new.

Po Liu reported recently that timestamping PTP over IPv4 is broken using
the felix driver on NXP LS1028A. This has been known for a while, of
course, since it has always been broken. The reason is because IP PTP
packets are currently treated as unknown IP multicast, which is not
flooded to the CPU port in the ocelot driver design, so packets don't
reach the ptp4l program.

The series solves the problem by installing packet traps per port when
the timestamping ioctl is called, depending on the RX filter selected
(L2, L4 or both).
====================

Link: https://lore.kernel.org/r/20211126172845.3149260-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The driver doesn't support RX timestamping for non-PTP packets, but it
declares that it does. Restrict the reported RX filters to PTP v2 over
L2 and over L4.

Fixes: 4e3b0468 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

IEEE 1588 support was declared too soon for the Ocelot switch. Out of
reset, this switch does not apply any special treatment for PTP packets,
i.e. when an event message is received, the natural tendency is to
forward it by MAC DA/VLAN ID. This poses a problem when the ingress port
is under a bridge, since user space application stacks (written
primarily for endpoint ports, not switches) like ptp4l expect that PTP
messages are always received on AF_PACKET / AF_INET sockets (depending
on the PTP transport being used), and never being autonomously
forwarded. Any forwarding, if necessary (for example in Transparent
Clock mode) is handled in software by ptp4l. Having the hardware forward
these packets too will cause duplicates which will confuse endpoints
connected to these switches.

So PTP over L2 barely works, in the sense that PTP packets reach the CPU
port, but they reach it via flooding, and therefore reach lots of other
unwanted destinations too. But PTP over IPv4/IPv6 does not work at all.
This is because the Ocelot switch have a separate destination port mask
for unknown IP multicast (which PTP over IP is) flooding compared to
unknown non-IP multicast (which PTP over L2 is) flooding. Specifically,
the driver allows the CPU port to be in the PGID_MC port group, but not
in PGID_MCIPV4 and PGID_MCIPV6. There are several presentations from
Allan Nielsen which explain that the embedded MIPS CPU on Ocelot
switches is not very powerful at all, so every penny they could save by
not allowing flooding to the CPU port module matters. Unknown IP
multicast did not make it.

The de facto consensus is that when a switch is PTP-aware and an
application stack for PTP is running, switches should have some sort of
trapping mechanism for PTP packets, to extract them from the hardware
data path. This avoids both problems:
(a) PTP packets are no longer flooded to unwanted destinations
(b) PTP over IP packets are no longer denied from reaching the CPU since
    they arrive there via a trap and not via flooding

It is not the first time when this change is attempted. Last time, the
feedback from Allan Nielsen and Andrew Lunn was that the traps should
not be installed by default, and that PTP-unaware switching may be
desired for some use cases:
https://patchwork.ozlabs.org/project/netdev/patch/20190813025214.18601-5-yangbo.lu@nxp.com/

To address that feedback, the present patch adds the necessary packet
traps according to the RX filter configuration transmitted by user space
through the SIOCSHWTSTAMP ioctl. Trapping is done via VCAP IS2, where we
keep 5 filters, which are amended each time RX timestamping is enabled
or disabled on a port:
- 1 for PTP over L2
- 2 for PTP over IPv4 (UDP ports 319 and 320)
- 2 for PTP over IPv6 (UDP ports 319 and 320)

The cookie by which these filters (invisible to tc) are identified is
strategically chosen such that it does not collide with the filters used
for the ocelot-8021q tagging protocol by the Felix driver, or with the
MRP traps set up by the Ocelot library.

Other alternatives were considered, like patching user space to do
something, but there are so many ways in which PTP packets could be made
to reach the CPU, generically speaking, that "do what?" is a very valid
question. The ptp4l program from the linuxptp stack already attempts to
do something: it calls setsockopt(IP_ADD_MEMBERSHIP) (and
PACKET_ADD_MEMBERSHIP, respectively) which translates in both cases into
a dev_mc_add() on the interface, in the kernel:
https://github.com/richardcochran/linuxptp/blob/v3.1.1/udp.c#L73
https://github.com/richardcochran/linuxptp/blob/v3.1.1/raw.c

Reality shows that this is not sufficient in case the interface belongs
to a switchdev driver, as dev_mc_add() does not show the intention to
trap a packet to the CPU, but rather the intention to not drop it (it is
strictly for RX filtering, same as promiscuous does not mean to send all
traffic to the CPU, but to not drop traffic with unknown MAC DA). This
topic is a can of worms in itself, and it would be great if user space
could just stay out of it.

On the other hand, setting up PTP traps privately within the driver is
not new by any stretch of the imagination:
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c#L833
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/dsa/hirschmann/hellcreek.c#L1050
https://elixir.bootlin.com/linux/v5.16-rc2/source/include/linux/dsa/sja1105.h#L21

So this is the approach taken here as well. The difference here being
that we prepare and destroy the traps per port, dynamically at runtime,
as opposed to driver init time, because apparently, PTP-unaware
forwarding is a use case.

Fixes: 4e3b0468 ("net: mscc: PTP Hardware Clock (PHC) support")
Reported-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

As opposed to event messages (Sync, PdelayReq etc) which require
timestamping, general messages (Announce, FollowUp etc) do not.
In PTP they are part of different streams of data.

IEEE 1588-2008 Annex D.2 "UDP port numbers" states that the UDP
destination port assigned by IANA is 319 for event messages, and 320 for
general messages. Yet the kernel seems to be missing the definition for
general messages. This patch adds it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

VCAP (Versatile Content Aware Processor) is the TCAM-based engine behind
tc flower offload on ocelot, among other things. The ingress port mask
on which VCAP rules match is present as a bit field in the actual key of
the rule. This means that it is possible for a rule to be shared among
multiple source ports. When the rule is added one by one on each desired
port, that the ingress port mask of the key must be edited and rewritten
to hardware.

But the API in ocelot_vcap.c does not allow for this. For one thing,
ocelot_vcap_filter_add() and ocelot_vcap_filter_del() are not symmetric,
because ocelot_vcap_filter_add() works with a preallocated and
prepopulated filter and programs it to hardware, and
ocelot_vcap_filter_del() does both the job of removing the specified
filter from hardware, as well as kfreeing it. That is to say, the only
option of editing a filter in place, which is to delete it, modify the
structure and add it back, does not work because it results in
use-after-free.

This patch introduces ocelot_vcap_filter_replace, which trivially
reprograms a VCAP entry to hardware, at the exact same index at which it
existed before, without modifying any list or allocating any memory.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The ocelot driver, when asked to timestamp all receiving packets, 1588
v1 or NTP, says "nah, here's 1588 v2 for you".

According to this discussion:
https://patchwork.kernel.org/project/netdevbpf/patch/20211104133204.19757-8-martin.kaistra@linutronix.de/#24577647
drivers that downgrade from a wider request to a narrower response (or
even a response where the intersection with the request is empty) are
buggy, and should return -ERANGE instead. This patch fixes that.

Fixes: 4e3b0468 ("net: mscc: PTP Hardware Clock (PHC) support")
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Guangbin Huang says:

====================
net: hns3: add some fixes for -net

This series adds some fixes for the HNS3 ethernet driver.
====================

Link: https://lore.kernel.org/r/20211126120318.33921-1-huangguangbin2@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, HNS3 driver doesn't clear the reset flags of components after
successfully executing reset, it causes userspace info of
"Components reset" and "Components not reset" is incorrect.

So fix this problem by clear corresponding reset flag after reset process.

Fixes: ddccc5e3 ("net: hns3: add support for triggering reset by ethtool")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, when user queries page pool info by debugfs command
"cat page_pool_info", the cnt of allocated page for page pool may be
incorrect because of memory inconsistency problem caused by compiler
optimization.

So this patch uses READ_ONCE() to read value of pages_state_hold_cnt to
fix this problem.

Fixes: 850bfb91 ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When page pool is not enabled, its address value is still NULL and page
pool should not be accessed, so add a check for it.

Fixes: 850bfb91 ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.

In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.

To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.

Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

If the variable 'p_bit->flags' is always 0,
the loop condition is always 0.

The variable 'j' may be greater than or equal to 32.

At this time, the array 'p_aeu->bits[32]' may be out
of bound.
Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Link: https://lore.kernel.org/r/20211125113610.273841-1-zhangyue1@kylinos.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull btrfs fix from David Sterba:
 "One more fix to the lzo code, a missing put_page causing memory leaks
  when some error branches are taken"

* tag 'for-5.16-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: fix the memory leak caused in lzo_compress_pages()

When applications call shutdown() with SHUT_RDWR in userspace,
smc_close_active() calls kernel_sock_shutdown(), and it is called
twice in smc_shutdown().

This fixes this by checking sk_state before do clcsock shutdown, and
avoids missing the application's call of smc_shutdown().

Link: https://lore.kernel.org/linux-s390/1f67548e-cbf6-0dce-82b5-10288a4583bd@linux.ibm.com/
Fixes: 606a63c9 ("net/smc: Ensure the active closing peer first closes clcsock")
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20211126024134.45693-1-tonylu@linux.alibaba.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Inject error before dev_hold(real_dev) in register_vlan_dev(),
and execute the following testcase:

ip link add dev dummy1 type dummy
ip link add name dummy1.100 link dummy1 type vlan id 100
ip link del dev dummy1

When the dummy netdevice is removed, we will get a WARNING as following:

=======================================================================
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 2 PID: 0 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0

and an endless loop of:

=======================================================================
unregister_netdevice: waiting for dummy1 to become free. Usage count = -1073741824

That is because dev_put(real_dev) in vlan_dev_free() be called without
dev_hold(real_dev) in register_vlan_dev(). It makes the refcnt of real_dev
underflow.

Move the dev_hold(real_dev) to vlan_dev_init() which is the call-back of
ndo_init(). That makes dev_hold() and dev_put() for vlan's real_dev
symmetrical.

Fixes: 563bcbae ("net: vlan: fix a UAF in vlan_dev_real_dev()")
Reported-by: Petr Machata <petrm@nvidia.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/r/20211126015942.2918542-1-william.xuanziyang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

All the filter names are missing _PTP in them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20211126031921.2466944-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

ethtool_set_coalesce() now uses both the .get_coalesce() and
.set_coalesce() callbacks. But the check for their availability is
buggy, so changing the coalesce settings on a device where the driver
provides only _one_ of the callbacks results in a NULL pointer
dereference instead of an -EOPNOTSUPP.

Fix the condition so that the availability of both callbacks is
ensured. This also matches the netlink code.

Note that reproducing this requires some effort - it only affects the
legacy ioctl path, and needs a specific combination of driver options:
- have .get_coalesce() and .coalesce_supported but no
 .set_coalesce(), or
- have .set_coalesce() but no .get_coalesce(). Here eg. ethtool doesn't
  cause the crash as it first attempts to call ethtool_get_coalesce()
  and bails out on error.

Fixes: f3ccfda1 ("ethtool: extend coalesce setting uAPI with CQE mode")
Cc: Yufeng Mo <moyufeng@huawei.com>
Cc: Huazhong Tan <tanhuazhong@huawei.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Link: https://lore.kernel.org/r/20211126175543.28000-1-jwi@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Device permissions is S_IALLUGO, with many unnecessary bits. Remove them
and also remove read and write permissions from group and others.

Before the change:
crwsrwsrwt    1 0        0          10, 125 Nov 25 13:59 /dev/virtual_nci

After the change:
crw-------    1 0        0          10, 125 Nov 25 14:05 /dev/virtual_nci
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Link: https://lore.kernel.org/r/20211125141457.716921-1-cascardo@canonical.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

when the number of DRR classes decreases, the round-robin active list can
contain elements that have already been freed in ets_qdisc_change(). As a
consequence, it's possible to see a NULL dereference crash, caused by the
attempt to call cl->qdisc->ops->peek(cl->qdisc) when cl->qdisc is NULL:

 BUG: kernel NULL pointer dereference, address: 0000000000000018
 #PF: supervisor read access in kernel mode
 #PF: error_code(0x0000) - not-present page
 PGD 0 P4D 0
 Oops: 0000 [#1] PREEMPT SMP NOPTI
 CPU: 1 PID: 910 Comm: mausezahn Not tainted 5.16.0-rc1+ #475
 Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014
 RIP: 0010:ets_qdisc_dequeue+0x129/0x2c0 [sch_ets]
 Code: c5 01 41 39 ad e4 02 00 00 0f 87 18 ff ff ff 49 8b 85 c0 02 00 00 49 39 c4 0f 84 ba 00 00 00 49 8b ad c0 02 00 00 48 8b 7d 10 <48> 8b 47 18 48 8b 40 38 0f ae e8 ff d0 48 89 c3 48 85 c0 0f 84 9d
 RSP: 0000:ffffbb36c0b5fdd8 EFLAGS: 00010287
 RAX: ffff956678efed30 RBX: 0000000000000000 RCX: 0000000000000000
 RDX: 0000000000000002 RSI: ffffffff9b938dc9 RDI: 0000000000000000
 RBP: ffff956678efed30 R08: e2f3207fe360129c R09: 0000000000000000
 R10: 0000000000000001 R11: 0000000000000001 R12: ffff956678efeac0
 R13: ffff956678efe800 R14: ffff956611545000 R15: ffff95667ac8f100
 FS:  00007f2aa9120740(0000) GS:ffff95667b800000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000018 CR3: 000000011070c000 CR4: 0000000000350ee0
 Call Trace:
  <TASK>
  qdisc_peek_dequeued+0x29/0x70 [sch_ets]
  tbf_dequeue+0x22/0x260 [sch_tbf]
  __qdisc_run+0x7f/0x630
  net_tx_action+0x290/0x4c0
  __do_softirq+0xee/0x4f8
  irq_exit_rcu+0xf4/0x130
  sysvec_apic_timer_interrupt+0x52/0xc0
  asm_sysvec_apic_timer_interrupt+0x12/0x20
 RIP: 0033:0x7f2aa7fc9ad4
 Code: b9 ff ff 48 8b 54 24 18 48 83 c4 08 48 89 ee 48 89 df 5b 5d e9 ed fc ff ff 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f3 0f 1e fa <53> 48 83 ec 10 48 8b 05 10 64 33 00 48 8b 00 48 85 c0 0f 85 84 00
 RSP: 002b:00007ffe5d33fab8 EFLAGS: 00000202
 RAX: 0000000000000002 RBX: 0000561f72c31460 RCX: 0000561f72c31720
 RDX: 0000000000000002 RSI: 0000561f72c31722 RDI: 0000561f72c31720
 RBP: 000000000000002a R08: 00007ffe5d33fa40 R09: 0000000000000014
 R10: 0000000000000000 R11: 0000000000000246 R12: 0000561f7187e380
 R13: 0000000000000000 R14: 0000000000000000 R15: 0000561f72c31460
  </TASK>
 Modules linked in: sch_ets sch_tbf dummy rfkill iTCO_wdt intel_rapl_msr iTCO_vendor_support intel_rapl_common joydev virtio_balloon lpc_ich i2c_i801 i2c_smbus pcspkr ip_tables xfs libcrc32c crct10dif_pclmul crc32_pclmul crc32c_intel ahci libahci ghash_clmulni_intel serio_raw libata virtio_blk virtio_console virtio_net net_failover failover sunrpc dm_mirror dm_region_hash dm_log dm_mod
 CR2: 0000000000000018

Ensuring that 'alist' was never zeroed [1] was not sufficient, we need to
remove from the active list those elements that are no more SP nor DRR.

[1] https://lore.kernel.org/netdev/60d274838bf09777f0371253416e8af71360bc08.1633609148.git.dcaratti@redhat.com/

v3: fix race between ets_qdisc_change() and ets_qdisc_dequeue() delisting
    DRR classes beyond 'nbands' in ets_qdisc_change() with the qdisc lock
    acquired, thanks to Cong Wang.

v2: when a NULL qdisc is found in the DRR active list, try to dequeue skb
    from the next list item.
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: dcc68b4d ("net: sch_ets: Add a new Qdisc")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Link: https://lore.kernel.org/r/7a5c496eed2d62241620bdbb83eb03fb9d571c99.1637762721.git.dcaratti@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge fix and cleanup related to the management of ACPI device
properties for 5.16-rc3.

* acpi-properties:
  ACPI: Make acpi_node_get_parent() local
  ACPI: Get acpi_device's parent from the parent field

Merge hibernation-related fixes for 5.16-rc3.

* pm-sleep:
  PM: hibernate: Fix snapshot partial write lengths
  PM: hibernate: use correct mode for swsusp_close()

The Tx queues were not disabled in situations where the driver needed to
stop the interface to apply a new configuration. This could result in a
kernel panic when doing any of the 3 following actions:
* reconfiguring the number of queues (ethtool -L)
* reconfiguring the size of the ring buffers (ethtool -G)
* installing/removing an XDP program (ip l set dev ethX xdp)

Prevent the panic by making sure netif_tx_disable is called when stopping
an interface.

Without this patch, the following kernel panic can be observed when doing
any of the actions above:

Unable to handle kernel paging request at virtual address ffff80001238d040
[....]
 Call trace:
  dwmac4_set_addr+0x8/0x10
  dev_hard_start_xmit+0xe4/0x1ac
  sch_direct_xmit+0xe8/0x39c
  __dev_queue_xmit+0x3ec/0xaf0
  dev_queue_xmit+0x14/0x20
[...]
[ end trace 0000000000000002 ]---

Fixes: 5fabb012 ("net: stmmac: Add initial XDP support")
Fixes: aa042f60 ("net: stmmac: Add support to Ethtool get/set ring parameters")
Fixes: 0366f7e0 ("net: stmmac: add ethtool support for get/set channels")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20211124154731.1676949-1-yannick.vignon@oss.nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull char/misc driver fix from Greg KH:
 "Here is a single binder driver fix for 5.16-rc3.

  It resolves a problem reported in the set of binder fixes that went
  into 5.16-rc1. It has been in linux-next for a while with no reported
  problems"

* tag 'char-misc-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  binder: fix test regression due to sender_euid change

Pull staging fixes from Greg KH:
 "Here are some small staging driver fixes and one driver removal for
  5.16-rc3.

  The fixes resolve a number of small issues found in 5.16-rc1, nothing
  huge at all. The driver removal was due to a platform being removed in
  5.16-rc1, but this driver was forgotten about. It wasn't being built
  anymore so it's safe to delete.

  All have been in linux-next for a while with no reported problems"

* tag 'staging-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: rtl8192e: Fix use after free in _rtl92e_pci_disconnect()
  staging: greybus: Add missing rwsem around snd_ctl_remove() calls
  staging: Remove Netlogic XLP network driver
  staging: r8188eu: fix a memory leak in rtw_wx_read32()
  staging: r8188eu: use GFP_ATOMIC under spinlock
  staging: r8188eu: Use kzalloc() with GFP_ATOMIC in atomic context
  staging/fbtft: Fix backlight
  staging: r8188eu: Fix breakage introduced when 5G code was removed

Pull USB fixes from Greg KH:
 "Here are a number of small USB fixes for reported problems for
  5.16-rc3

  They include:

   - typec driver fixes

   - new usb-serial driver ids

   - usb hub enumeration issues that were much reported

   - gadget driver fixes

   - dwc3 driver fix

   - chipidea driver fixe

  All of these have been in linux-next with no reported problems"

* tag 'usb-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: serial: option: add Fibocom FM101-GL variants
  usb: typec: tipd: Fix initialization sequence for cd321x
  usb: typec: tipd: Fix typo in cd321x_switch_power_state
  usb: hub: Fix locking issues with address0_mutex
  USB: serial: pl2303: fix GC type detection
  USB: serial: option: add Telit LE910S1 0x9200 composition
  usb: chipidea: ci_hdrc_imx: fix potential error pointer dereference in probe
  usb: hub: Fix usb enumeration issue due to address0 race
  usb: typec: fusb302: Fix masking of comparator and bc_lvl interrupts
  usb: dwc3: leave default DMA for PCI devices
  usb: dwc2: hcd_queue: Fix use of floating point literal
  usb: dwc3: gadget: Fix null pointer exception
  usb: gadget: udc-xilinx: Fix an error handling path in 'xudc_probe()'
  usb: xhci: tegra: Check padctrl interrupt presence in device tree
  usb: dwc2: gadget: Fix ISOC flow for elapsed frames
  usb: dwc3: gadget: Check for L1/L2/U3 for Start Transfer
  usb: dwc3: gadget: Ignore NoStream after End Transfer
  usb: dwc3: core: Revise GHWPARAMS9 offset

Pull MMC host fixes from Ulf Hansson:

 - mmc_spi: Add SPI IDs to silence warning

 - sdhci: Fix ADMA for PAGE_SIZE >= 64KiB

 - sdhci-esdhc-imx: Disable broken CMDQ for imx8qm/imx8qxp/imx8mm

* tag 'mmc-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: spi: Add device-tree SPI IDs
  mmc: sdhci: Fix ADMA for PAGE_SIZE >= 64KiB
  mmc: sdhci-esdhc-imx: disable CMDQ support

Pull i2c fixes from Wolfram Sang:
 "I2C has an interrupt storm fix for the i801, better timeout handling
  for the new virtio driver, and some documentation fixes this time"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  docs: i2c: smbus-protocol: mention the repeated start condition
  i2c: virtio: disable timeout handling
  i2c: i801: Fix interrupt storm from SMB_ALERT signal
  i2c: i801: Restore INTREN on unload
  dt-bindings: i2c: imx-lpi2c: Fix i.MX 8QM compatible matching

Pull xen fixes from Juergen Gross:

 - Kconfig fix to make it possible to control building of the privcmd
   driver

 - three fixes for issues identified by the kernel test robot

 - a five-patch series to simplify timeout handling for Xen PV driver
   initialization

 - two patches to fix error paths in xenstore/xenbus driver
   initialization

* tag 'for-linus-5.16c-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen: make HYPERVISOR_set_debugreg() always_inline
  xen: make HYPERVISOR_get_debugreg() always_inline
  xen: detect uninitialized xenbus in xenbus_init
  xen: flag xen_snd_front to be not essential for system boot
  xen: flag pvcalls-front to be not essential for system boot
  xen: flag hvc_xen to be not essential for system boot
  xen: flag xen_drm_front to be not essential for system boot
  xen: add "not_essential" flag to struct xenbus_driver
  xen/pvh: add missing prototype to header
  xen: don't continue xenstore initialization in case of errors
  xen/privcmd: make option visible in Kconfig

Pull arm64 fixes from Will Deacon:
 "Three arm64 fixes.

  The main one is a fix to the way in which we evaluate the macro
  arguments to our uaccess routines, which we _think_ might be the root
  cause behind some unkillable tasks we've seen in the Android arm64 CI
  farm (testing is ongoing). In any case, it's worth fixing.

  Other than that, we've toned down an over-zealous VM_BUG_ON() and
  fixed ftrace stack unwinding in a bunch of cases.

  Summary:

   - Evaluate uaccess macro arguments outside of the critical section

   - Tighten up VM_BUG_ON() in pmd_populate_kernel() to avoid false positive

   - Fix ftrace stack unwinding using HAVE_FUNCTION_GRAPH_RET_ADDR_PTR"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: uaccess: avoid blocking within critical sections
  arm64: mm: Fix VM_BUG_ON(mm != &init_mm) for trans_pgd
  arm64: ftrace: use HAVE_FUNCTION_GRAPH_RET_ADDR_PTR

[BUG]
Fstests generic/027 is pretty easy to trigger a slow but steady memory
leak if run with "-o compress=lzo" mount option.

Normally one single run of generic/027 is enough to eat up at least 4G ram.

[CAUSE]
In commit d4088803 ("btrfs: subpage: make lzo_compress_pages()
compatible") we changed how @page_in is released.

But that refactoring makes @page_in only released after all pages being
compressed.

This leaves error path not releasing @page_in. And by "error path"
things like incompressible data will also be treated as an error
(-E2BIG).

Thus it can cause a memory leak if even nothing wrong happened.

[FIX]
Add check under @out label to release @page_in when needed, so when we
hit any error, the input page is properly released.
Reported-by: Josef Bacik <josef@toxicpanda.com>
Fixes: d4088803 ("btrfs: subpage: make lzo_compress_pages() compatible")
Reviewed-and-tested-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

Jakub Kicinski says:

====================
tls: splice_read fixes

As I work my way to unlocked and zero-copy TLS Rx the obvious bugs
in the splice_read implementation get harder and harder to ignore.
This is to say the fixes here are discovered by code inspection,
I'm not aware of anyone actually using splice_read.
====================

Link: https://lore.kernel.org/r/20211124232557.2039757-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Previous patch fixes overriding callbacks incorrectly. Triggering
the crash in sendpage_locked would be more spectacular but it's
hard to get to, so take the easier path of proving this is broken
and call getname. We're currently getting IPv4 socket info on an
IPv6 socket.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We replace proto_ops whenever TLS is configured for RX. But our
replacement also overrides sendpage_locked, which will crash
unless TX is also configured. Similarly we plug both of those
in for TLS_HW (NIC crypto offload) even tho TLS_HW has a completely
different implementation for TX.

Last but not least we always plug in something based on inet_stream_ops
even though a few of the callbacks differ for IPv6 (getname, release,
bind).

Use a callback building method similar to what we do for struct proto.

Fixes: c46234eb ("tls: RX path for ktls")
Fixes: d4ffb02d ("net/tls: enable sk_msg redirect to tls socket egress")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add tests for half-received and peeked records.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>