ARM: DT: Hisilicon ARM32 SoCs updates for v5.9

- Update L2 cache controller nodes to fix dtschema validator warnings
  for hi3620 and hix5hd2

* tag 'hisi-arm32-dt-for-5.9' of git://github.com/hisilicon/linux-hisi:
  ARM: dts: hisilicon: Align L2 cache-controller nodename with dtschema

Link: https://lore.kernel.org/r/5F165FA1.2030301@hisilicon.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'sunxi-dt-for-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt

Our usual number of patches to improve the Allwinner Device Tree
support, including:
  - CPUFreq / Thermal throttling support for the H5
  - Touchscreen support for the Pinephone
  - New boards: PinePhone v1.2

* tag 'sunxi-dt-for-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  arm64: dts: allwinner: h5: bananapi-m2-plus-v1.2: Tie in CPU OPPs
  arm64: dts: allwinner: h5: libretech-all-h3-cc: Tie in CPU OPPs
  arm64: dts: allwinner: h5: Add CPU Operating Performance Points table
  arm64: dts: allwinner: h5: Add trip and cooling maps to CPU thermal zones
  arm64: dts: allwinner: h5: Add clock to CPU cores
  ARM: dts: sunxi: bananapi-m2-plus-v1.2: Fix CPU supply voltages
  ARM: dts: sunxi: bananapi-m2-plus-v1.2: Add regulator supply to all CPU cores
  ARM: dts: sunxi: libretech-all-h3-cc: Add regulator supply to all CPU cores
  arm64: dts: sun50i-pinephone: dldo4 must not be >= 1.8V
  arm64: dts: allwinner: Add support for PinePhone revision 1.2
  dt-bindings: arm: sunxi: Add PinePhone 1.2 bindings
  arm64: dts: sun50i-a64-pinephone: Add touchscreen support
  arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone
  ARM: dts: orange-pi-zero-plus2: add leds configuration
  ARM: dts: orange-pi-zero-plus2: enable USB OTG port

Link: https://lore.kernel.org/r/fa48ffcb-3404-41bb-b065-a16717cf5688.lettre@localhostSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'versatile-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/dt

Versatile DTS changes for the v5.9 kernel cycle, essentially
just a single patch fixing up the node names for schema.

* tag 'versatile-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
  ARM: dts: arm-realview: Align L2 cache-controller nodename with dtschema

Link: https://lore.kernel.org/r/CACRpkdbkM9ZmuG2FnBmO7upcJfnqq2oSLDCFDXC5b3K+dtps9Q@mail.gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'imx-dt64-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt

i.MX arm64 device tree update for 5.9:

- Update i.MX8M OCOTP device node name to match .yaml schema.
- Add ftm_alarm0 device support for layerscape SoCs.
- Add DSPI controller support for lx2160a device.
- A series from Peng Fan to add aliases for various devices on i.MX8
  SoCs.
- Add Hantro G1/G2 VPU device support for imx8mq.
- Add more thermal zone support for ls1028a, ls1043a and ls1046a.
- Other small random changes.

* tag 'imx-dt64-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (26 commits)
  arm64: dts: lx2160a-rdb: fix shunt-resistor value
  arm64: dts: ls1028a-qds: Add DSPI flash nodes
  arm64: dts: lx2160a: Increase configuration space size
  arm64: dts: zii-ultra: update MDIO speed and preamble
  arm64: dts: ls1043a: update USB nodes status to match board config
  arm64: dts: imx8mn-evk: add pca9450 for i.mx8mn-evk board
  arm64: dts: imx8mp: add ddr pmu device node
  arm64: dts: ls1043a: add more thermal zone support
  arm64: dts: ls1046a: add more thermal zone support
  arm64: dts: layerscape: add ftm_alarm0 node
  arm64: dts: ls1028a: Add ftm_alarm0 DT node
  arm64: dts: lx2160a: add ftm_alarm0 DT node
  arm64: dts: lx2160a: add DT node for all DSPI controller
  arm64: dts: lx2160a: add dspi controller DT nodes
  arm64: dts: imx8mp: Add fallback compatible to ocotp node
  arm64: dts: imx8qxp: Add ethernet alias
  arm64: dts: imx8qxp: add i2c aliases
  arm64: dts: imx8qxp: add alias for lsio MU
  arm64: dts: imx8m: add mu node
  arm64: dts: imx8m: change ocotp node name on i.MX8M SoCs
  ...

Link: https://lore.kernel.org/r/20200720085536.24138-4-shawnguo@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

i.MX device tree update for 5.9:

- New board support: Protonic PRTI6Q/WD2/VT7/RVT and MYiR MYS-6ULX SBC.
- Update IIM, OCOTP and SD/MMC device node name to match .yaml bindings.
- Make tempmon node as child of anatop node according to hardware
  architecture.
- The vf610-zii device update: configure fiber port to 1000BaseX, add
  switch watchdog, MDIO speed and preamble.
- A series from Fabio Estevam to update imx6qdl-sabresd and
  imx6q-tbs2910 for using MDIO node and reset-assert-us.
- Align L2 cache-controller device node name with .yaml schema.
- Enable SATA support for imx6qp-sabreauto and imx6qp-sabresd board.
- A series of patches from Shengjiu Wang to enable various audio
  support on i.MX6 devices.
- Add Gateworks System Controller support for imx6qdl-gw devices.
- Change default #pwm-cells setting to <3> in the SoC dtsi files.
- Other small random changes.

* tag 'imx-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (43 commits)
  ARM: dts: vf610-zii-ssmb-spu3: Add node for switch watchdog
  ARM: dts: vf610-zii-ssmb-dtu: Add no-sdio/no-sd properties
  ARM: dts: imx6q-tbs2910: Pass reset-assert-us
  ARM: dts: imx6q-tbs2910: Add an mdio node
  ARM: dts: imx6qdl-sabresd: Pass reset-assert-us
  ARM: dts: imx6qdl-sabresd: Add an mdio node
  ARM: dts: imx6qdl-gw: add Gateworks System Controller support
  ARM: dts: imx6ull: add MYiR MYS-6ULX SBC
  ARM: dts: vf610-zii-spb4: Add node for switch watchdog
  ARM: dts: colibri-imx6: remove pinctrl-names orphan
  ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files
  ARM: dts: vf610-zii-scu4-aib: Configure fibre ports to 1000BaseX
  ARM: dts: vf610-zii-dev-rev-c: Configure fiber port to 1000BaseX
  ARM: dts: ZII: update MDIO speed and preamble
  ARM: dts: vfxxx: Add node for CAAM
  ARM: dts: imx6qp-sabresd: enable sata
  ARM: dts: imx6qp-sabreauto: enable sata
  ARM: dts: add Protonic RVT board
  ARM: dts: add Protonic VT7 board
  ARM: dts: add Protonic WD2 board
  ...

Link: https://lore.kernel.org/r/20200720085536.24138-3-shawnguo@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'imx-bindings-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt

i.MX DT bindings for 5.9:

- Add compatible for Protonic PRTI6Q, WD2, RVT, VT7 boards.
- Add compatible for MYiR Tech iMX6ULL Evaluation Board

* tag 'imx-bindings-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  dt-bindings: arm: fsl: Add MYiR Tech boards
  dt-bindings: arm: fsl: add different Protonic boards

Link: https://lore.kernel.org/r/20200720085536.24138-2-shawnguo@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'socfpga_dts_update_for_v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/dt

SoCFPGA DTS updates for v5.9
- Populate clock entries for Agilex platform
- Add "reset-names" to SPI entries
- Add Maxim max1619 temperature sensor to Arria10 devkit

* tag 'socfpga_dts_update_for_v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  ARM: dts: socfpga: add the temperature sensor to the Arria10 devkit
  arm: dts: socfpga: add reset-names to spi node
  arm64: dts: agilex: add nand clocks
  arm64: dts: agilex: populate clock dts entries for Intel SoCFPGA Agilex

Link: https://lore.kernel.org/r/20200719011804.15599-1-dinguyen@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

The Bananapi M2 Plus H5 v1.2 can work with the standard H5 OPPs.
Tie them in to enable CPU frequency scaling.

The original Bananapi M2 Plus H5 is left out for now, as adding
the fixed regulator along with the enable pin seemed to cause some
glitching in Linux.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-9-wens@kernel.org

The Libre Computer ALL-H3-CC H5 variant can work with the standard H5
OPPs. Tie them in to enable CPU frequency scaling.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-8-wens@kernel.org

Add an OPP (Operating Performance Points) table for the CPU cores for
boards to include to DVFS (Dynamic Voltage & Frequency Scaling) on the
H5. The table originates from Armbian, but the maximum voltage is raised
slightly to account for boards using slightly higher voltages.

The table and tie in to the CPU cores are put in a separate dtsi file
that board files can include to opt in. Or they can define their own
tables if the standard one does not fit.

This has been tested on the Libre Computer ALL-H3-CC-H5 and the Bananapi
M2+ v1.2 H5, both with adequate cooling. The former has a fixed 1.2V
regulator, while the latter has a GPIO controlled regulator switchable
between 1.1V and 1.3V.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-7-wens@kernel.org

This enables passive cooling by down-regulating CPU voltage and frequency.
The trip points were copied from the H3.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-6-wens@kernel.org

The ARM CPU cores are fed by the CPU clock from the CCU. Add a
reference to the clock for each CPU core, along with the clock
transition latency.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-5-wens@kernel.org

The Bananapi M2+ uses a GPIO line to change the effective resistance of
the CPU supply regulator's feedback resistor network. The voltages
described in the device tree were given directly by the vendor. This
turns out to be slightly off compared to the real values.

The updated voltages are based on calculations of the feedback resistor
network, and verified down to three decimal places with a multi-meter.

Fixes: 6eeb4180 ("ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-4-wens@kernel.org

The device tree currently only assigns the a supply for the first CPU
core, when in reality the regulator supply is shared by all four cores.
This might cause an issue if the implementation does not realize the
sharing of the supply.

Assign the same regulator supply to the remaining CPU cores to address
this.

Fixes: 6eeb4180 ("ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-3-wens@kernel.org

The device tree currently only assigns the a supply for the first CPU
core, when in reality the regulator supply is shared by all four cores.
This might cause an issue if the implementation does not realize the
sharing of the supply.

Assign the same regulator supply to the remaining CPU cores to address
this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-2-wens@kernel.org

Add I2C child node for switch watchdog present on SPU3
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

esdhc0 is connected to an eMMC, so it is safe to pass the "no-sdio"/"no-sd"
properties.

esdhc1 is wired to a standard SD socket, so pass the "no-sdio" property.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix value of shunt-resistor property.
The LX2160A-RDB has 500 uOhm shunt for
the INA220, not 1000 uOhm. Unless
it will get wrong power consumption(1/2)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to the AR8035 datasheet:

"When using crystal, the clock is generated internally after power is
stable. For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset 1ms
requirement is satisfied."

Pass the 'reset-assert-us' property to describe such requirement.

While at it, use the 'reset-gpios' property inside the the mdio
node instead of the deprecated usage of 'phy-reset-gpios'.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6q-tbs2910 has an Atheros AR8035 Ethernet PHY at address 4.

The AR8035 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin.

Improve the Ethernet representation by adding an mdio node with such
information.

This fixes an Ethernet regression in U-Boot as U-Boot AR803X driver now
expects the 'qca,clk-out-frequency' property to be passed via
device tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Tested-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to the AR8031 datasheet:

"When using crystal, clock is generated internally after the power is
stable. In order to get reliable power-on-reset, it is recommended to
keep asserting the reset low signal long enough (10 ms) to ensure the
clock is stable and clock-to-reset (1 ms) requirement is satisfied."

Pass the 'reset-assert-us' property to describe such requirement.

While at it, use the 'reset-gpios' property inside the the mdio
node instead of the deprecated usage of 'phy-reset-gpios'.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6qdl-sabresd has an Atheros AR8031 Ethernet PHY at address 1.

The AR8031 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin.

Improve the Ethernet representation by adding an mdio node with such
information.

An advantage of adding the mdio node is that the AR8031 initialization
code in the mx6sabresd board file in U-Boot can totally be removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add entries for MYiR Tech imx6ULL eval boards.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Gateworks System Controller support to Gateworks Ventana boards:
- add dt bindings for GSC mfd driver and hwmon driver for ADC's and
  fan controllers.
- add dt bindings for gpio-keys driver for push-button and interrupt events
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the Maxim max1619 temp sensor that is on the Arria10 devkit.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

Add reset-names = "spi" to spi dts nodes.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

Add the clock properties for the NAND dts node.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

Add clock dts entries to the Intel SoCFPGA Agilex platform.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

Merge tag 'tegra-for-5.9-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt

arm64: tegra: Device tree changes for v5.9-rc1

This contains a slew of fixes in preparation for validating device trees
against json-schema bindings. In addition, this enables the CPU complex
(for CPU frequency scaling) and GPU on Tegra194.

* tag 'tegra-for-5.9-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (56 commits)
  arm64: tegra: Add the GPU on Tegra194
  arm64: tegra: Add compatible string for Tegra194 CPU complex
  arm64: tegra: Add HDMI supplies on Norrin
  arm64: tegra: Add #{address,size}-cells for VI I2C on Tegra210
  arm64: tegra: Add missing clocks and power-domains to Tegra210 VI I2C
  arm64: tegra: Add clocks and resets for ISP on Tegra210
  arm64: tegra: Fix compatible string for DPAUX on Tegra210
  arm64: tegra: Add i2c-bus subnode for DPAUX controllers
  arm64: tegra: Sort aliases alphabetically
  arm64: tegra: Remove spurious tabs
  arm64: tegra: Populate VBUS for USB3 on Jetson TX2
  arm64: tegra: Enable DFLL support on Jetson Nano
  arm64: tegra: Add support for Jetson Xavier NX
  arm64: tegra: Re-order PCIe aperture mappings
  arm64: tegra: Enable Tegra VI CSI support for Jetson Nano
  arm64: tegra: jetson-tx1: Add camera supplies
  arm64: tegra: Fix order of XUSB controller clocks
  arm64: tegra: Rename cbb@0 to bus@0 on Tegra194
  arm64: tegra: Sort nodes by unit-address on Jetson Nano
  arm64: tegra: Various fixes for PMICs
  ...

Link: https://lore.kernel.org/r/20200717161300.1661002-7-thierry.reding@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'tegra-for-5.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt

ARM: tegra: Device tree changes for v5.9-rc1

This adds device trees for the ASUS Google Nexus 7 and Acer Iconia Tab
A500. In addition there are a slew of fixes to existing device trees in
preparation for validating the DTBs against json-schema.

* tag 'tegra-for-5.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (38 commits)
  ARM: tegra: Add device-tree for ASUS Google Nexus 7
  ARM: tegra: Add device-tree for Acer Iconia Tab A500
  ARM: tegra: Add HDMI supplies on Nyan boards
  ARM: tegra: Add missing DSI controller on Tegra30
  ARM: tegra: Add i2c-bus subnode for DPAUX controllers
  ARM: tegra: The Tegra30 SDHCI is not backwards-compatible
  ARM: tegra: The Tegra30 DC is not backwards-compatible
  ARM: tegra: Remove spurious comma from node name
  ARM: tegra: Add parent clock to DSI output
  ARM: tegra: Use standard names for SRAM nodes
  ARM: tegra: seaboard: Use standard battery bindings
  ARM: tegra: Use standard names for LED nodes
  ARM: tegra: Use numeric unit-addresses
  ARM: tegra: medcom-wide: Remove extra panel power supply
  ARM: tegra: Use proper unit-addresses for OPPs
  ARM: tegra: Add missing clock-names for SDHCI controllers
  ARM: tegra: Fix order of XUSB controller clocks
  ARM: tegra: Add #reset-cells to Tegra124 memory controller
  ARM: tegra: Add missing panel power supplies
  ARM: tegra: Add micro-USB A/B port on Jetson TK1
  ...

Link: https://lore.kernel.org/r/20200717161300.1661002-5-thierry.reding@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'tegra-for-5.9-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt

dt-bindings: Changes for v5.9-rc1

This adds compatible strings for some new devices as well as updates and
fixes existing bindings.

* tag 'tegra-for-5.9-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  dt-bindings: fuse: tegra: Add missing compatible strings
  dt-bindings: i2c: tegra: Document Tegra210 VI I2C clocks and power-domains
  dt-bindings: Add documentation for GV11B GPU
  dt-bindings: ARM: tegra: Add ASUS Google Nexus 7
  dt-bindings: ARM: tegra: Add Acer Iconia Tab A500
  dt-bindings: Add vendor prefix for Acer Inc.
  dt-bindings: tegra: Document Jetson Xavier NX (and devkit)

Link: https://lore.kernel.org/r/20200717161300.1661002-1-thierry.reding@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt

arm64: dts: amlogic updates for v5.9
- meson-gx: Switch to the meson-ee-pwrc bindings
- add Khadas MCU nodes

* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  arm64: dts: amlogic: Add the Ethernet "timing-adjustment" clock
  arm64: dts: meson-gx: Switch to the meson-ee-pwrc bindings
  arm64: dts: meson-khadas-vim3: add Khadas MCU nodes

Link: https://lore.kernel.org/r/7h8sfif2na.fsf@baylibre.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt

ARM: dts: amlogic updates for v5.9
- power-domain and MMC updates

* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM: dts: meson8b: odroidc1: enable the SDHC controller
  ARM: dts: meson8b: ec100: enable the SDHC controller
  ARM: dts: meson: add the SDHC MMC controller
  ARM: dts: meson8b: add power domain controller
  ARM: dts: meson8m2: add resets for the power domain controller
  ARM: dts: meson8: add power domain controller

Link: https://lore.kernel.org/r/7hd04uf2o8.fsf@baylibre.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

The GPU found on NVIDIA Tegra194 SoCs is a Volta generation GPU called
GV11B.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The Tegra FUSE device tree bindings haven't been updated in a while. Add
compatible strings for the SoC generations that were released since the
last update.
Signed-off-by: Thierry Reding <treding@nvidia.com>

This patch documents missing clocks and power-domains of Tegra210 VI I2C.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The GV11B's device tree bindings are the same as for GP10B, though the
GPU is not completely compatible, so all that is needed is a different
compatible string.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Merge tag 'renesas-dt-bindings-for-v5.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas DT binding updates for v5.9

  - Document core support for the RZ/G2H SoC,
  - Document support for the HopeRun HiHope RZ/G2H, and Beacon
    EmbeddedWorks RZ/G2M boards.

* tag 'renesas-dt-bindings-for-v5.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  dt-bindings: arm: renesas: Document beacon-rzg2m
  dt-bindings: reset: renesas,rst: Document r8a774e1 reset module
  dt-bindings: power: renesas,rcar-sysc: Document r8a774e1 SYSC binding
  dt-bindings: arm: renesas: Add HopeRun RZ/G2H boards
  dt-bindings: arm: renesas: Document RZ/G2H SoC DT bindings

Link: https://lore.kernel.org/r/20200717112427.26032-4-geert+renesas@glider.beSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-arm-dt-for-v5.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas ARM DT updates for v5.9 (take two)

  - SPI Multi I/O Bus Controller (RPC-IF) support for R-Car V3H and V3M,
    including QSPI support for the Condor, Eagle, V3HSK, and V3MSK
    boards,
  - Initial support for the RZ/G2H SoC on the HopeRun HiHope RZ/G2H
    board,
  - Initial support for the Beacon EmbeddedWorks RZ/G2M board,
  - Minor fixes and improvements.

* tag 'renesas-arm-dt-for-v5.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (34 commits)
  ARM: dts: sh73a0: Add missing clocks to sound node
  arm64: dts: renesas: r8a774e1: Add CAN[FD] support
  arm64: dts: renesas: r8a774e1: Add RWDT node
  arm64: dts: renesas: r8a774e1: Add MSIOF nodes
  arm64: dts: renesas: r8a774e1: Add I2C and IIC-DVFS support
  arm64: dts: renesas: r8a774e1: Add SDHI nodes
  arm64: dts: renesas: r8a774e1: Add SCIF and HSCIF nodes
  arm64: dts: renesas: r8a774e1: Add TMU device nodes
  arm64: dts: renesas: r8a774e1: Add CMT device nodes
  arm64: dts: renesas: r8a774e1: Add RZ/G2H thermal support
  arm64: dts: renesas: r8a774e1: Add operating points
  arm64: dts: renesas: Introduce r8a774a1-beacon-rzg2m-kit
  arm64: dts: renesas: r8a774e1: Add Ethernet AVB node
  arm64: dts: renesas: r8a774e1: Add GPIO device nodes
  arm64: dts: renesas: r8a774e1: Add SYS-DMAC device nodes
  arm64: dts: renesas: r8a774e1: Add IPMMU device nodes
  ARM: dts: gose: Fix ports node name for adv7612
  ARM: dts: renesas: Fix SD Card/eMMC interface device node names
  arm64: dts: renesas: Fix SD Card/eMMC interface device node names
  arm64: dts: renesas: add full-pwr-cycle-in-suspend into eMMC nodes
  ...

Link: https://lore.kernel.org/r/20200717112427.26032-2-geert+renesas@glider.beSigned-off-by: Arnd Bergmann <arnd@arndb.de>

The device node for the FIFO-buffered Serial Interface sound node lacks
the "clocks" property, as the DTS file didn't describe any clocks yet at
its introduction.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200519075525.24742-1-geert+renesas@glider.be