Add driver for the PWM controller on Toshiba Visconti ARM SoC.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[thierry.reding@gmail.com: fix up a couple of checkpatch warnings]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Add bindings for the Toshiba Visconti PWM Controller.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

A test with the command below gives this error:

/arch/arm64/boot/dts/rockchip/rk3368-evb-act8846.dt.yaml:
pwm@ff680030: clock-names: ['pwm'] is too short

Devices with only one PWM clock use it to both to derive the functional
clock for the device and as the bus clock. The driver does not need
"clock-names" to get a handle, so remove them all.

make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/pwm/pwm-rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

A test with the command below gives this error:

/arch/arm/boot/dts/rk3036-evb.dt.yaml:
pwm@20050030: clock-names: ['pwm'] is too short

Devices with only one PWM clock use it to both to derive the functional
clock for the device and as the bus clock. The driver does not need
"clock-names" to get a handle, so remove them all.

make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/pwm/pwm-rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The compatible strings below are already in use in the Rockchip
DTSI files, but were somehow never added to a document, so add

"rockchip,rk3328-pwm"

"rockchip,rk3036-pwm", "rockchip,rk2928-pwm"

"rockchip,rk3368-pwm", "rockchip,rk3288-pwm"
"rockchip,rk3399-pwm", "rockchip,rk3288-pwm"

"rockchip,px30-pwm", "rockchip,rk3328-pwm"
"rockchip,rk3308-pwm", "rockchip,rk3328-pwm"

for PWM nodes to pwm-rockchip.yaml.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Current dts files with 'pwm' nodes are manually verified. In order to
automate this process pwm-rockchip.txt has to be converted to YAML.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Fix the following clang warning:

drivers/pwm/pwm-mediatek.c:110:19: warning: unused function
'pwm_mediatek_readl' [-Wunused-function].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The chip does not come out of POR in active state but in sleep state.
To be sure (in case the bootloader woke it up) we force it to sleep in
probe.

If runtime PM is disabled, we instead wake the chip in .probe and put it
to sleep in .remove.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Implement .get_state to read-out the current hardware state.

The hardware readout may return slightly different values than those
that were set in apply due to the limited range of possible prescale and
counter register values.

Also note that although the datasheet mentions 200 Hz as default
frequency when using the internal 25 MHz oscillator, the calculated
period from the default prescaler register setting of 30 is 5079040ns.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The switch to the atomic API goes hand in hand with a few fixes to
previously experienced issues:
- The duty cycle is no longer lost after disable/enable (previously the
  OFF registers were cleared in disable and the user was required to
  call config to restore the duty cycle settings)
- If one sets a period resulting in the same prescale register value,
  the sleep and write to the register is now skipped
- Previously, only the full ON bit was toggled in GPIO mode (and full
  OFF cleared if set to high), which could result in both full OFF and
  full ON not being set and on=0, off=0, which is not allowed according
  to the datasheet
- The OFF registers were reset to 0 in probe, which could lead to the
  forbidden on=0, off=0. Fixed by resetting to POR default (full OFF)
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.

So drop the hardware modification from the .remove() callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Before pwmchip_remove() returns the PWM is expected to be functional. So
remove the pwmchip before disabling the clocks.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.

So drop the hardware modification from the .remove() callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.

So drop the hardware modification from the .remove() callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Before pwmchip_remove() returns the PWM is expected to be functional. So
remove the pwmchip before disabling the clock.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing.) Also if disabling an enabled PWM was the right thing to do, this
should better be done in the framework instead of in each low level driver.

So drop the hardware modification from the .remove() callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Before pwmchip_remove() returns the PWM is expected to be functional. So
remove the pwmchip before disabling the clock.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Before pwmchip_remove() returns the PWM is expected to be functional. So
remove the pwmchip before disabling the clock.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Before pwmchip_remove() returns the PWM is expected to be functional. So
remove the pwmchip before disabling the clock.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Given that lowlevel drivers usually cannot implement exactly what a
consumer requests with pwm_apply_state() there is some rounding
involved.

pwm_get_state() returns the setting that was requested most recently by
the consumer (opposed to what was actually implemented in hardware in
reply to the last request). Clarify this in the function kerneldoc.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

pwmchip_add() only calls pwmchip_add_with_polarity() and nothing else. All
other users of pwmchip_add_with_polarity() are gone. So drop
pwmchip_add_with_polarity() and move the code instead to pwmchip_add().

The initial assignment to pwm->state.polarity is dropped. In every correct
usage of the PWM API this value is overwritten later anyhow.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The only side effect of this change is that pwm->state.polarity is
initialized to PWM_POLARITY_NORMAL instead of PWM_POLARITY_INVERSED.
However all other members of pwm->state are uninitialized and consumers
are expected to provide the right polarity (either by setting it explicitly
or by using a helper like pwm_init_state() that overwrites .polarity
anyhow with a value independent of the initial value).
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The only side effect of this change is that pwm->state.polarity is
initialized to PWM_POLARITY_NORMAL instead of PWM_POLARITY_INVERSED.
However all other members of pwm->state are uninitialized and consumers
are expected to provide the right polarity (either by setting it explicitly
or by using a helper like pwm_init_state() that overwrites .polarity
anyhow with a value independent of the initial value).

The eventual goal is to remove pwmchip_add_with_polarity() and so simplify
the data flow in the PWM core.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The driver only supports normal polarity and so should refuse requests
for inversed polarity.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The driver only supports normal polarity and so should refuse requests
for inversed polarity.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Otherwise the PWM stops working before the PWM core and its consumers
are aware the device is going away.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

This is just pushing down the core's compat code down into the driver using
the legacy callback nearly unchanged. The call to .enable() was just
dropped from .config() because .apply() calls it unconditionally.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Since commit 2b1c1a5d ("pwm: Use -EINVAL for unsupported polarity")
all drivers implementing the apply callback are unified to return
-EINVAL if an unsupported polarity is requested. Do the same in the
compat code for old-style drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Since commit 5e5da1e9 ("pwm: ab8500: Explicitly allocate pwm chip
base dynamically") all drivers use dynamic ID allocation explicitly. New
drivers are supposed to do the same, so remove support for driver
specified base IDs and drop all assignments in the low-level drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

There is no need to split the dev_err() call in three lines.

Use a single line to improve readability.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

With an input clk rate bigger than 2000000000, scaler would have been
zero which then would have resulted in a division by zero.

Also the originally implemented algorithm divided by the result of a
division. This nearly always looses precision. Consider a requested period
of 1000000 ns. With an input clock frequency of 32786885 Hz the hardware
was configured with an actual period of 983869.007 ns (PERIOD = 32258)
while the hardware can provide 1000003.508 ns (PERIOD = 32787).
And note if the input clock frequency was 32786886 Hz instead, the hardware
was configured to 1016656.477 ns (PERIOD = 33333) while the optimal
setting results in 1000003.477 ns (PERIOD = 32787).

This patch implements proper range checking and only divides once for
the calculation of period (and similar for duty_cycle).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Tested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Pull rdma fixes from Jason Gunthorpe:
 "Nothing special here, though Bob's regression fixes for rxe would have
  made it before the rc cycle had there not been such strong winter
  weather!

   - Fix corner cases in the rxe reference counting cleanup that are
     causing regressions in blktests for SRP

   - Two kdoc fixes so W=1 is clean

   - Missing error return in error unwind for mlx5

   - Wrong lock type nesting in IB CM"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  RDMA/rxe: Fix errant WARN_ONCE in rxe_completer()
  RDMA/rxe: Fix extra deref in rxe_rcv_mcast_pkt()
  RDMA/rxe: Fix missed IB reference counting in loopback
  RDMA/uverbs: Fix kernel-doc warning of _uverbs_alloc
  RDMA/mlx5: Set correct kernel-doc identifier
  IB/mlx5: Add missing error code
  RDMA/rxe: Fix missing kconfig dependency on CRYPTO
  RDMA/cm: Fix IRQ restore in ib_send_cm_sidr_rep

Pull gcc-plugins fixes from Kees Cook:
 "Tiny gcc-plugin fixes for v5.12-rc2. These issues are small but have
  been reported a couple times now by static analyzers, so best to get
  them fixed to reduce the noise. :)

   - Fix coding style issues (Jason Yan)"

* tag 'gcc-plugins-v5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  gcc-plugins: latent_entropy: remove unneeded semicolon
  gcc-plugins: structleak: remove unneeded variable 'ret'

Pull pstore fixes from Kees Cook:

 - Rate-limit ECC warnings (Dmitry Osipenko)

 - Fix error path check for NULL (Tetsuo Handa)

* tag 'pstore-v5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  pstore/ram: Rate-limit "uncorrectable error in header" message
  pstore: Fix warning in pstore_kill_sb()

Merge tag 'for-5.12/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:
 "Fix DM verity target's optional Forward Error Correction (FEC) for
  Reed-Solomon roots that are unaligned to block size"

* tag 'for-5.12/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm verity: fix FEC for RS roots unaligned to block size
  dm bufio: subtract the number of initial sectors in dm_bufio_get_device_size

Pull block fixes from Jens Axboe:

 - NVMe fixes:
      - more device quirks (Julian Einwag, Zoltán Böszörményi, Pascal
        Terjan)
      - fix a hwmon error return (Daniel Wagner)
      - fix the keep alive timeout initialization (Martin George)
      - ensure the model_number can't be changed on a used subsystem
        (Max Gurtovoy)

 - rsxx missing -EFAULT on copy_to_user() failure (Dan)

 - rsxx remove unused linux.h include (Tian)

 - kill unused RQF_SORTED (Jean)

 - updated outdated BFQ comments (Joseph)

 - revert work-around commit for bd_size_lock, since we removed the
   offending user in this merge window (Damien)

* tag 'block-5.12-2021-03-05' of git://git.kernel.dk/linux-block:
  nvmet: model_number must be immutable once set
  nvme-fabrics: fix kato initialization
  nvme-hwmon: Return error code when registration fails
  nvme-pci: add quirks for Lexar 256GB SSD
  nvme-pci: mark Kingston SKC2000 as not supporting the deepest power state
  nvme-pci: mark Seagate Nytro XM1440 as QUIRK_NO_NS_DESC_LIST.
  rsxx: Return -EFAULT if copy_to_user() fails
  block/bfq: update comments and default value in docs for fifo_expire
  rsxx: remove unused including <linux/version.h>
  block: Drop leftover references to RQF_SORTED
  block: revert "block: fix bd_size_lock use"

Pull io_uring fixes from Jens Axboe:
 "A bit of a mix between fallout from the worker change, cleanups and
  reductions now possible from that change, and fixes in general. In
  detail:

   - Fully serialize manager and worker creation, fixing races due to
     that.

   - Clean up some naming that had gone stale.

   - SQPOLL fixes.

   - Fix race condition around task_work rework that went into this
     merge window.

   - Implement unshare. Used for when the original task does unshare(2)
     or setuid/seteuid and friends, drops the original workers and forks
     new ones.

   - Drop the only remaining piece of state shuffling we had left, which
     was cred. Move it into issue instead, and we can drop all of that
     code too.

   - Kill f_op->flush() usage. That was such a nasty hack that we had
     out of necessity, we no longer need it.

   - Following from ->flush() removal, we can also drop various bits of
     ctx state related to SQPOLL and cancelations.

   - Fix an issue with IOPOLL retry, which originally was fallout from a
     filemap change (removing iov_iter_revert()), but uncovered an issue
     with iovec re-import too late.

   - Fix an issue with system suspend.

   - Use xchg() for fallback work, instead of cmpxchg().

   - Properly destroy io-wq on exec.

   - Add create_io_thread() core helper, and use that in io-wq and
     io_uring. This allows us to remove various silly completion events
     related to thread setup.

   - A few error handling fixes.

  This should be the grunt of fixes necessary for the new workers, next
  week should be quieter. We've got a pending series from Pavel on
  cancelations, and how tasks and rings are indexed. Outside of that,
  should just be minor fixes. Even with these fixes, we're still killing
  a net ~80 lines"

* tag 'io_uring-5.12-2021-03-05' of git://git.kernel.dk/linux-block: (41 commits)
  io_uring: don't restrict issue_flags for io_openat
  io_uring: make SQPOLL thread parking saner
  io-wq: kill hashed waitqueue before manager exits
  io_uring: clear IOCB_WAITQ for non -EIOCBQUEUED return
  io_uring: don't keep looping for more events if we can't flush overflow
  io_uring: move to using create_io_thread()
  kernel: provide create_io_thread() helper
  io_uring: reliably cancel linked timeouts
  io_uring: cancel-match based on flags
  io-wq: ensure all pending work is canceled on exit
  io_uring: ensure that threads freeze on suspend
  io_uring: remove extra in_idle wake up
  io_uring: inline __io_queue_async_work()
  io_uring: inline io_req_clean_work()
  io_uring: choose right tctx->io_wq for try cancel
  io_uring: fix -EAGAIN retry with IOPOLL
  io-wq: fix error path leak of buffered write hash map
  io_uring: remove sqo_task
  io_uring: kill sqo_dead and sqo submission halting
  io_uring: ignore double poll add on the same waitqueue head
  ...

Pull power management fixes from Rafael Wysocki:
 "These fix the usage of device links in the runtime PM core code and
  update the DTPM (Dynamic Thermal Power Management) feature added
  recently.

  Specifics:

   - Make the runtime PM core code avoid attempting to suspend supplier
     devices before updating the PM-runtime status of a consumer to
     'suspended' (Rafael Wysocki).

   - Fix DTPM (Dynamic Thermal Power Management) root node
     initialization and label that feature as EXPERIMENTAL in Kconfig
     (Daniel Lezcano)"

* tag 'pm-5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  powercap/drivers/dtpm: Add the experimental label to the option description
  powercap/drivers/dtpm: Fix root node initialization
  PM: runtime: Update device status before letting suppliers suspend