Use recently updated R-Car Gen2 CMT0 and CMT1 compat strings.

With this change in place we can keep device-specific configuration in
the driver and the driver can be able to support CMT1 specific features.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use the recently updated r8a73a4 CMT1 compat string.

With this change in place we can keep device-specific configuration in
the driver and the driver can be able to support CMT1 specific features.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the device tree node for the Advanced Power Management Unit (APMU).
Use the "enable-method" prop to  point out that the APMU should be used
for the SMP support.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The Renesas part number of the two-wire serial interface EEPROM is not
24C128, but R1EX24128ASA00A.

Hence change its primary compatible value to "renesas,r1ex24128".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The Renesas part number of the two-wire serial interface EEPROM is not
24C02, but R1EX24002ATAS0G.

Hence change its primary compatible value to "renesas,r1ex24002", like
on Gose.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add VIN[01] support to SoC dt. Also, add aliases.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add VIN[012] support to SoC dt. Also, add aliases.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable PCIe Controller & set PCIe bus clock frequency.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds a default PCIe bus clock node.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

CAN1 interface is exposed via connector J3 found on the camera daughter
board. This patch enables can1 DT node from within the daughter board
specific dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch enables CAN0 interface exposed through connector J20 on the
carrier board.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the definitions for can0 and can1 to the SoC .dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

CAN1 interface is exposed via connector J1 found on the HDMI daughter
board. This patch enables can1 DT node from within the daughter board
specific device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch enables CAN0 interface exposed through connector J15 on the
carrier board.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the definitions for can0 and can1 to the SoC .dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch enables the HDMI interface found on the expansion board.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add du node to r8a7745 SoC DT. Boards that want to enable the DU
need to specify the output topology.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

cec-clock is a fixed clock generator that is not controlled by i2c5 and
thus should not be a child of the i2c5 bus node. Rather, it should be
a child of the root node of the DT.

Fixes: 02a5ab18 ("ARM: dts: koelsch: Add CEC clock for HDMI transmitter")
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use newly added R-Car SDHI Gen2 fallback compat string
in the DT of the r8a7794 SoC.

This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use newly added R-Car SDHI Gen2 fallback compat string
in the DT of the r8a7793 SoC.

This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use newly added R-Car SDHI Gen2 fallback compat string
in the DT of the r8a7792 SoC.

This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use newly added R-Car SDHI Gen2 fallback compat string
in the DT of the r8a7791 SoC.

This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use newly added R-Car SDHI Gen2 fallback compat string
in the DT of the r8a7790 SoC.

This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use newly added R-Car SDHI Gen1 fallback compat string
in the DT of the r8a7779 SoC.

This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use newly added R-Car SDHI Gen1 fallback compat string
in the DT of the r8a7778 SoC.

This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use newly added R-Car SDHI Gen2 fallback compat string
in the DT of the r8a7745 SoC.

This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use newly added R-Car SDHI Gen2 fallback compat string
in the DT of the r8a7743 SoC.

This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add iic0 and iic1 nodes to SoC dtsi. Also, define aliases i2c6
and i2c7. Board specific DT files will enable the interfaces
if needed.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

From: Biju Das <biju.das@bp.renesas.com>

Enable HS-USB on iWave RZ/G1E carrier board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

From: Biju Das <biju.das@bp.renesas.com>

This patch adds DMA properties to the HSUSB node.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

From: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

From: Biju Das <biju.das@bp.renesas.com>

Define the R8A7745 generic part of the HS-USB device node. It is up to the
board file to enable the device.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Improve the layout of r8a7745-iwg22d-sodimm.dts by sorting the
nodes alphabetically.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add file r8a7745-iwg22d-sodimm-dbhd-ca.dts to provide support for
iW-RainboW-G22D with HDMI daughter board plugged in.

The interfaces defined in the new .dts file are: scif1, scif5,
and hscif2.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add support for HSCIF1 as /dev/ttySC5, keeping the same naming
scheme adopted by iWave in their BSP release. This interface
uses RTS/CTS.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The BSP release from iWave uses /dev/ttySC3 as debug console, this patch
renames the alias accordingly for compatibility.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Although there is a HDMI connector on the q7 carrier board it is not
connected to the RZ/G1M SoC. One must use the HDMI connector on the
camera daughter board.

This patch adds support for this connector.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add du node to r8a7743 SoC DT. Boards that want to enable the DU
need to specify the output topology.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>