pci_get_device() will decrease the reference count for the *from*
parameter. So we don't need to call put_device() to decrease the
reference. Let's remove the put_device() in the loop and only decrease
the reference count of the returned 'pdev' for the last loop because it
will not be passed to pci_get_device() as input parameter. We don't need
to check if 'pdev' is NULL because it is already checked inside
pci_dev_put(). Also add pci_dev_put() for the error path.

Fixes: fe1939bb ("octeontx2-af: Add SDP interface support")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Link: https://lore.kernel.org/r/20221123065919.31499-1-wangxiongfeng2@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Call phylink_disconnect_phy() in tse_shutdown() to release the
resources occupied by phylink_of_phy_connect() in the tse_open().

Fixes: fef29982 ("net: altera: tse: convert to phylink")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Link: https://lore.kernel.org/r/20221123011617.332302-1-liujian56@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When doing the following test steps, an error was found:
  step 1: modprobe virtio_net succeeded
    # modprobe virtio_net        <-- OK

  step 2: fault injection in register_netdevice()
    # modprobe -r virtio_net     <-- OK
    # ...
      FAULT_INJECTION: forcing a failure.
      name failslab, interval 1, probability 0, space 0, times 0
      CPU: 0 PID: 3521 Comm: modprobe
      Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
      Call Trace:
       <TASK>
       ...
       should_failslab+0xa/0x20
       ...
       dev_set_name+0xc0/0x100
       netdev_register_kobject+0xc2/0x340
       register_netdevice+0xbb9/0x1320
       virtnet_probe+0x1d72/0x2658 [virtio_net]
       ...
       </TASK>
      virtio_net: probe of virtio0 failed with error -22

  step 3: modprobe virtio_net failed
    # modprobe virtio_net        <-- failed
      virtio_net: probe of virtio0 failed with error -2

The root cause of the problem is that the queues are not
disable on the error handling path when register_netdevice()
fails in virtnet_probe(), resulting in an error "-ENOENT"
returned in the next modprobe call in setup_vq().

virtio_pci_modern_device uses virtqueues to send or
receive message, and "queue_enable" records whether the
queues are available. In vp_modern_find_vqs(), all queues
will be selected and activated, but once queues are enabled
there is no way to go back except reset.

Fix it by reset virtio device on error handling path. This
makes error handling follow the same order as normal device
cleanup in virtnet_remove() which does: unregister, destroy
failover, then reset. And that flow is better tested than
error handling so we can be reasonably sure it works well.

Fixes: 02465555 ("virtio_net: fix use after free on allocation failure")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20221122150046.3910638-1-lizetao1@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The ACPI buffer memory (buffer.pointer) should be freed as the
buffer is not used after acpi_evaluate_object(), free it to
prevent memory leak.

Fixes: 13e920d9 ("net: wwan: t7xx: Add core components")
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/1669119580-28977-1-git-send-email-guohanjun@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

As the devm_kcalloc may return NULL pointer,
it should be better to add check for the return
value, as same as the others.

Fixes: e8e095b3 ("octeontx2-af: cn10k: Bandwidth profiles config support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20221122055449.31247-1-jiasheng@iscas.ac.cnSigned-off-by: Paolo Abeni <pabeni@redhat.com>

In the blamed commit, a rudimentary reallocation procedure for RX buffer
descriptors was implemented, for the situation when their format changes
between normal (no PTP) and extended (PTP).

enetc_hwtstamp_set() calls enetc_close() and enetc_open() in a sequence,
and this sequence loses information which was previously configured in
the TX BDR Mode Register, specifically via the enetc_set_bdr_prio() call.
The TX ring priority is configured by tc-mqprio and tc-taprio, and
affects important things for TSN such as the TX time of packets. The
issue manifests itself most visibly by the fact that isochron --txtime
reports premature packet transmissions when PTP is first enabled on an
enetc interface.

Save the TX ring priority in a new field in struct enetc_bdr (occupies a
2 byte hole on arm64) in order to make this survive a ring reconfiguration.

Fixes: 434cebab ("enetc: Add dynamic allocation of extended Rx BD rings")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/r/20221122130936.1704151-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If prestera_port_sfp_bind() fails, unregister_netdev() should be called
in error handling path.

Compile tested only.

Fixes: 52323ef7 ("net: marvell: prestera: add phylink support")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/1669115432-36841-1-git-send-email-zhangchangzhong@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Martin Faltesek says:

====================
nfc: st-nci: Restructure validating logic in EVT_TRANSACTION

These are the same 3 patches that were applied in st21nfca here:
https://lore.kernel.org/netdev/20220607025729.1673212-1-mfaltesek@google.com
with a couple minor differences.

st-nci has nearly identical code to that of st21nfca for EVT_TRANSACTION,
except that there are two extra validation checks that are not present
in the st-nci code.

The 3/3 patch as coded for st21nfca pulls those checks in, bringing both
drivers into parity.
====================

Link: https://lore.kernel.org/r/20221122004246.4186422-1-mfaltesek@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The transaction buffer is allocated by using the size of the packet buf,
and subtracting two which seems intended to remove the two tags which are
not present in the target structure. This calculation leads to under
counting memory because of differences between the packet contents and the
target structure. The aid_len field is a u8 in the packet, but a u32 in
the structure, resulting in at least 3 bytes always being under counted.
Further, the aid data is a variable length field in the packet, but fixed
in the structure, so if this field is less than the max, the difference is
added to the under counting.

To fix, perform validation checks progressively to safely reach the
next field, to determine the size of both buffers and verify both tags.
Once all validation checks pass, allocate the buffer and copy the data.
This eliminates freeing memory on the error path, as validation checks are
moved ahead of memory allocation.
Reported-by: Denis Efremov <denis.e.efremov@oracle.com>
Reviewed-by: Guenter Roeck <groeck@google.com>
Fixes: 5d1ceb7f ("NFC: st21nfcb: Add HCI transaction event support")
Signed-off-by: Martin Faltesek <mfaltesek@google.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Error path does not free previously allocated memory. Add devm_kfree() to
the failure path.
Reported-by: Denis Efremov <denis.e.efremov@oracle.com>
Reviewed-by: Guenter Roeck <groeck@google.com>
Fixes: 5d1ceb7f ("NFC: st21nfcb: Add HCI transaction event support")
Signed-off-by: Martin Faltesek <mfaltesek@google.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The first validation check for EVT_TRANSACTION has two different checks
tied together with logical AND. One is a check for minimum packet length,
and the other is for a valid aid_tag. If either condition is true (fails),
then an error should be triggered. The fix is to change && to ||.
Reported-by: Denis Efremov <denis.e.efremov@oracle.com>
Reviewed-by: Guenter Roeck <groeck@google.com>
Fixes: 5d1ceb7f ("NFC: st21nfcb: Add HCI transaction event support")
Signed-off-by: Martin Faltesek <mfaltesek@google.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Steffen Klassert says:

====================
ipsec 2022-11-23

1) Fix "disable_policy" on ipv4 early demuxP Packets after
   the initial packet in a flow might be incorectly dropped
   on early demux if there are no matching policies.
   From Eyal Birger.

2) Fix a kernel warning in case XFRM encap type is not
   available. From Eyal Birger.

3) Fix ESN wrap around for GSO to avoid a double usage of a
    sequence number. From Christian Langrock.

4) Fix a send_acquire race with pfkey_register.
   From Herbert Xu.

5) Fix a list corruption panic in __xfrm_state_delete().
   Thomas Jarosch.

6) Fix an unchecked return value in xfrm6_init().
   Chen Zhongjin.

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
  xfrm: Fix ignored return value in xfrm6_init()
  xfrm: Fix oops in __xfrm_state_delete()
  af_key: Fix send_acquire race with pfkey_register
  xfrm: replay: Fix ESN wrap around for GSO
  xfrm: lwtunnel: squelch kernel warning in case XFRM encap type is not available
  xfrm: fix "disable_policy" on ipv4 early demux
====================

Link: https://lore.kernel.org/r/20221123093117.434274-1-steffen.klassert@secunet.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

1) Fix regression in ipset hash:ip with IPv4 range, from Vishwanath Pai.
   This is fixing up a bug introduced in the 6.0 release.

2) The "netfilter: ipset: enforce documented limit to prevent allocating
   huge memory" patch contained a wrong condition which makes impossible to
   add up to 64 clashing elements to a hash:net,iface type of set while it
   is the documented feature of the set type. The patch fixes the condition
   and thus makes possible to add the elements while keeps preventing
   allocating huge memory, from Jozsef Kadlecsik. This has been broken
   for several releases.

3) Missing locking when updating the flow block list which might lead
   a reader to crash. This has been broken since the introduction of the
   flowtable hardware offload support.

* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  netfilter: flowtable_offload: add missing locking
  netfilter: ipset: restore allowing 64 clashing elements in hash:net,iface
  netfilter: ipset: regression in ip_set_hash_ip.c
====================

Link: https://lore.kernel.org/r/20221122212814.63177-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The documentation refers to invalid web page under www.linuxfoundation.org
The patch refers to a working URL under wiki.linuxfoundation.org
Signed-off-by: Nir Levy <bhr166@gmail.com>
Link: https://lore.kernel.org/all/20221120220630.7443-1-bhr166@gmail.com/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ZLP for DisplayLink ethernet devices was enabled in 6.0:
266c0190 ("net/cdc_ncm: Enable ZLP for DisplayLink ethernet devices").
The related driver_info should be the "same as cdc_ncm_info, but with
FLAG_SEND_ZLP". However, set_rx_mode that enables handling multicast
traffic was missing in the new cdc_ncm_zlp_info.

usbnet_cdc_update_filter rx mode was introduced in linux 5.9 with:
e10dcb1b ("net: cdc_ncm: hook into set_rx_mode to admit multicast
traffic")

Without this hook, multicast, and then IPv6 SLAAC, is broken.

Fixes: 266c0190 ("net/cdc_ncm: Enable ZLP for DisplayLink ethernet devices")
Signed-off-by: Santiago Ruano Rincón <santiago.ruano-rincon@imt-atlantique.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add RmNet support for LARA-L6.

LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface

In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

When holding a reader-writer spin lock we cannot sleep. Calling
setup_udp_tunnel_sock() with write lock held violates this rule, because we
end up calling percpu_down_read(), which might sleep, as syzbot reports
[1]:

 __might_resched.cold+0x222/0x26b kernel/sched/core.c:9890
 percpu_down_read include/linux/percpu-rwsem.h:49 [inline]
 cpus_read_lock+0x1b/0x140 kernel/cpu.c:310
 static_key_slow_inc+0x12/0x20 kernel/jump_label.c:158
 udp_tunnel_encap_enable include/net/udp_tunnel.h:187 [inline]
 setup_udp_tunnel_sock+0x43d/0x550 net/ipv4/udp_tunnel_core.c:81
 l2tp_tunnel_register+0xc51/0x1210 net/l2tp/l2tp_core.c:1509
 pppol2tp_connect+0xcdc/0x1a10 net/l2tp/l2tp_ppp.c:723

Trim the writer-side critical section for sk_callback_lock down to the
minimum, so that it covers only operations on sk_user_data.

Also, when grabbing the sk_callback_lock, we always need to disable BH, as
Eric points out. Failing to do so leads to deadlocks because we acquire
sk_callback_lock in softirq context, which can get stuck waiting on us if:

1) it runs on the same CPU, or

       CPU0
       ----
  lock(clock-AF_INET6);
  <Interrupt>
    lock(clock-AF_INET6);

2) lock ordering leads to priority inversion

       CPU0                    CPU1
       ----                    ----
  lock(clock-AF_INET6);
                               local_irq_disable();
                               lock(&tcp_hashinfo.bhash[i].lock);
                               lock(clock-AF_INET6);
  <Interrupt>
    lock(&tcp_hashinfo.bhash[i].lock);

... as syzbot reports [2,3]. Use the _bh variants for write_(un)lock.

[1] https://lore.kernel.org/netdev/0000000000004e78ec05eda79749@google.com/
[2] https://lore.kernel.org/netdev/000000000000e38b6605eda76f98@google.com/
[3] https://lore.kernel.org/netdev/000000000000dfa31e05eda76f75@google.com/

v2:
- Check and set sk_user_data while holding sk_callback_lock for both
  L2TP encapsulation types (IP and UDP) (Tetsuo)

Cc: Tom Parkin <tparkin@katalix.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Fixes: b68777d5 ("l2tp: Serialize access to sk_user_data with sk_callback_lock")
Reported-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+703d9e154b3b58277261@syzkaller.appspotmail.com
Reported-by: syzbot+50680ced9e98a61f7698@syzkaller.appspotmail.com
Reported-by: syzbot+de987172bb74a381879b@syzkaller.appspotmail.com
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The dm9051_loop_rx() returns without release skb when dm9051_stop_mrcmd()
returns error, free the skb to avoid this leak.

Fixes: 2dc95a4d ("net: Add dm9051 driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In com20020_probe(), if com20020_config() fails, dev and info
will not be freed, which will lead to a memory leak.

This patch adds freeing dev and info after com20020_config()
fails to fix this bug.

Compile tested only.

Fixes: 15b99ac1 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5 fixes 2022-11-21

This series provides bug fixes to mlx5 driver.

* tag 'mlx5-fixes-2022-11-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
  net/mlx5e: Fix possible race condition in macsec extended packet number update routine
  net/mlx5e: Fix MACsec update SecY
  net/mlx5e: Fix MACsec SA initialization routine
  net/mlx5e: Remove leftovers from old XSK queues enumeration
  net/mlx5e: Offload rule only when all encaps are valid
  net/mlx5e: Fix missing alignment in size of MTT/KLM entries
  net/mlx5: Fix sync reset event handler error flow
  net/mlx5: E-Switch, Set correctly vport destination
  net/mlx5: Lag, avoid lockdep warnings
  net/mlx5: Fix handling of entry refcount when command is not issued to FW
  net/mlx5: cmdif, Print info on any firmware cmd failure to tracepoint
  net/mlx5: SF: Fix probing active SFs during driver probe phase
  net/mlx5: Fix FW tracer timestamp calculation
  net/mlx5: Do not query pci info while pci disabled
====================

Link: https://lore.kernel.org/r/20221122022559.89459-1-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In fib_table_insert(), if the alias was already inserted, but node not
exist, the error code should be set before return from error handling path.

Fixes: a6c76c17 ("ipv4: Notify route after insertion to the routing table")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/r/20221120072838.2167047-1-william.xuanziyang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Yan Cangang says:

====================
net: ethernet: mtk_eth_soc: fix memory leak in error path
====================

Link: https://lore.kernel.org/r/20221120055259.224555-1-nalanzeyu@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In mtk_ppe_init(), when dmam_alloc_coherent() or devm_kzalloc() failed,
the rhashtable ppe->l2_flows isn't destroyed. Fix it.

In mtk_probe(), when mtk_ppe_init() or mtk_eth_offload_init() or
register_netdev() failed, have the same problem. Fix it.

Fixes: 33fc42de ("net: ethernet: mtk_eth_soc: support creating mac address based offload entries")
Signed-off-by: Yan Cangang <nalanzeyu@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In mtk_probe(), when mtk_ppe_init() or mtk_eth_offload_init() failed,
mtk_mdio_cleanup() isn't called. Fix it.

Fixes: ba37b7ca ("net: ethernet: mtk_eth_soc: add support for initializing the PPE")
Fixes: 502e84e2 ("net: ethernet: mtk_eth_soc: add flow offloading support")
Signed-off-by: Yan Cangang <nalanzeyu@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When fail to dma_map_single() in mtk_rx_alloc(), it returns directly.
But the memory allocated for local variable data is not freed, and
local variabel data has not been attached to ring->data[i] yet, so the
memory allocated for local variable data will not be freed outside
mtk_rx_alloc() too. Thus memory leak would occur in this scenario.

Add skb_free_frag(data) when dma_map_single() failed.

Fixes: 23233e57 ("net: ethernet: mtk_eth_soc: rely on page_pool for single page buffers")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Link: https://lore.kernel.org/r/20221120035405.1464341-1-william.xuanziyang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Kuniyuki Iwashima says:

====================
dccp/tcp: Fix bhash2 issues related to WARN_ON() in inet_csk_get_port().

syzkaller was hitting a WARN_ON() in inet_csk_get_port() in the 4th patch,
which was because we forgot to fix up bhash2 bucket when connect() for a
socket bound to a wildcard address fails in __inet_stream_connect().

There was a similar report [0], but its repro does not fire the WARN_ON() due
to inconsistent error handling.

When connect() for a socket bound to a wildcard address fails, saddr may or
may not be reset depending on where the failure happens.  When we fail in
__inet_stream_connect(), sk->sk_prot->disconnect() resets saddr.  OTOH, in
(dccp|tcp)_v[46]_connect(), if we fail after inet_hash6?_connect(), we
forget to reset saddr.

We fix this inconsistent error handling in the 1st patch, and then we'll
fix the bhash2 WARN_ON() issue.

Note that there is still an issue in that we reset saddr without checking
if there are conflicting sockets in bhash and bhash2, but this should be
another series.

See [1][2] for the previous discussion.

[0]: https://lore.kernel.org/netdev/0000000000003f33bc05dfaf44fe@google.com/
[1]: https://lore.kernel.org/netdev/20221029001249.86337-1-kuniyu@amazon.com/
[2]: https://lore.kernel.org/netdev/20221103172419.20977-1-kuniyu@amazon.com/
[3]: https://lore.kernel.org/netdev/20221118081906.053d5231@kernel.org/T/#m00aafedb29ff0b55d5e67aef0252ef1baaf4b6ee
====================

Link: https://lore.kernel.org/r/20221119014914.31792-1-kuniyu@amazon.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If a socket bound to a wildcard address fails to connect(), we
only reset saddr and keep the port.  Then, we have to fix up the
bhash2 bucket; otherwise, the bucket has an inconsistent address
in the list.

Also, listen() for such a socket will fire the WARN_ON() in
inet_csk_get_port(). [0]

Note that when a system runs out of memory, we give up fixing the
bucket and unlink sk from bhash and bhash2 by inet_put_port().

[0]:
WARNING: CPU: 0 PID: 207 at net/ipv4/inet_connection_sock.c:548 inet_csk_get_port (net/ipv4/inet_connection_sock.c:548 (discriminator 1))
Modules linked in:
CPU: 0 PID: 207 Comm: bhash2_prev_rep Not tainted 6.1.0-rc3-00799-gc8421681c845 #63
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-1.amzn2022.0.1 04/01/2014
RIP: 0010:inet_csk_get_port (net/ipv4/inet_connection_sock.c:548 (discriminator 1))
Code: 74 a7 eb 93 48 8b 54 24 18 0f b7 cb 4c 89 e6 4c 89 ff e8 48 b2 ff ff 49 8b 87 18 04 00 00 e9 32 ff ff ff 0f 0b e9 34 ff ff ff <0f> 0b e9 42 ff ff ff 41 8b 7f 50 41 8b 4f 54 89 fe 81 f6 00 00 ff
RSP: 0018:ffffc900003d7e50 EFLAGS: 00010202
RAX: ffff8881047fb500 RBX: 0000000000004e20 RCX: 0000000000000000
RDX: 000000000000000a RSI: 00000000fffffe00 RDI: 00000000ffffffff
RBP: ffffffff8324dc00 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000000
R13: 0000000000000001 R14: 0000000000004e20 R15: ffff8881054e1280
FS:  00007f8ac04dc740(0000) GS:ffff88842fc00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020001540 CR3: 00000001055fa003 CR4: 0000000000770ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
 <TASK>
 inet_csk_listen_start (net/ipv4/inet_connection_sock.c:1205)
 inet_listen (net/ipv4/af_inet.c:228)
 __sys_listen (net/socket.c:1810)
 __x64_sys_listen (net/socket.c:1819 net/socket.c:1817 net/socket.c:1817)
 do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
 entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)
RIP: 0033:0x7f8ac051de5d
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 93 af 1b 00 f7 d8 64 89 01 48
RSP: 002b:00007ffc1c177248 EFLAGS: 00000206 ORIG_RAX: 0000000000000032
RAX: ffffffffffffffda RBX: 0000000020001550 RCX: 00007f8ac051de5d
RDX: ffffffffffffff80 RSI: 0000000000000000 RDI: 0000000000000004
RBP: 00007ffc1c177270 R08: 0000000000000018 R09: 0000000000000007
R10: 0000000020001540 R11: 0000000000000206 R12: 00007ffc1c177388
R13: 0000000000401169 R14: 0000000000403e18 R15: 00007f8ac0723000
 </TASK>

Fixes: 28044fc1 ("net: Add a bhash2 table hashed by port and address")
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Joanne Koong <joannelkoong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When we call connect() for a socket bound to a wildcard address, we update
saddr locklessly.  However, it could result in a data race; another thread
iterating over bhash might see a corrupted address.

Let's update saddr under the bhash bucket's lock.

Fixes: 3df80d93 ("[DCCP]: Introduce DCCPv6")
Fixes: 7c657876 ("[DCCP]: Initial implementation")
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Joanne Koong <joannelkoong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When we call inet_bhash2_update_saddr(), prev_saddr is always non-NULL.
Let's remove the unnecessary test.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Joanne Koong <joannelkoong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When connect() is called on a socket bound to the wildcard address,
we change the socket's saddr to a local address.  If the socket
fails to connect() to the destination, we have to reset the saddr.

However, when an error occurs after inet_hash6?_connect() in
(dccp|tcp)_v[46]_conect(), we forget to reset saddr and leave
the socket bound to the address.

From the user's point of view, whether saddr is reset or not varies
with errno.  Let's fix this inconsistent behaviour.

Note that after this patch, the repro [0] will trigger the WARN_ON()
in inet_csk_get_port() again, but this patch is not buggy and rather
fixes a bug papering over the bhash2's bug for which we need another
fix.

For the record, the repro causes -EADDRNOTAVAIL in inet_hash6_connect()
by this sequence:

  s1 = socket()
  s1.setsockopt(SOL_SOCKET, SO_REUSEADDR, 1)
  s1.bind(('127.0.0.1', 10000))
  s1.sendto(b'hello', MSG_FASTOPEN, (('127.0.0.1', 10000)))
  # or s1.connect(('127.0.0.1', 10000))

  s2 = socket()
  s2.setsockopt(SOL_SOCKET, SO_REUSEADDR, 1)
  s2.bind(('0.0.0.0', 10000))
  s2.connect(('127.0.0.1', 10000))  # -EADDRNOTAVAIL

  s2.listen(32)  # WARN_ON(inet_csk(sk)->icsk_bind2_hash != tb2);

[0]: https://syzkaller.appspot.com/bug?extid=015d756bbd1f8b5c8f09

Fixes: 3df80d93 ("[DCCP]: Introduce DCCPv6")
Fixes: 7c657876 ("[DCCP]: Initial implementation")
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Joanne Koong <joannelkoong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

nf_flow_table_block_setup and the driver TC_SETUP_FT call can modify the flow
block cb list while they are being traversed elsewhere, causing a crash.
Add a write lock around the calls to protect readers

Fixes: c29f74e0 ("netfilter: nf_flow_table: hardware offload support")
Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The commit 510841da ("netfilter: ipset: enforce documented limit to
prevent allocating huge memory") was too strict and prevented to add up to
64 clashing elements to a hash:net,iface type of set. This patch fixes the
issue and now the type behaves as documented.

Fixes: 510841da ("netfilter: ipset: enforce documented limit to prevent allocating huge memory")
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

If PTP synchronisation is done every second, then sporadic the interval
is higher than one second:

ptp4l[696.582]: master offset        -17 s2 freq   -1891 path delay 573
ptp4l[697.582]: master offset        -22 s2 freq   -1901 path delay 573
ptp4l[699.368]: master offset         -1 s2 freq   -1887 path delay 573
      ^^^^^^^ Should be 698.582!

This problem is caused by rotten packets, which are received after
polling but before interrupts are enabled again. This can be fixed by
checking for pending work and rescheduling if necessary after interrupts
has been enabled again.

Fixes: 403f69bb ("tsnep: Add TSN endpoint Ethernet MAC driver")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://lore.kernel.org/r/20221119211825.81805-1-gerhard@engleder-embedded.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Commit 4581dd48 ("net: octeontx2-pf: mcs: consider MACSEC setting")
has already added "depends on MACSEC || !MACSEC", so remove it.
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20221119133616.3583538-1-zhengbin13@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put(). Call pci_dev_put() before returning from
bnx2x_vf_is_pcie_pending() to avoid refcount leak.

Fixes: b56e9670 ("bnx2x: Prepare device and initialize VF database")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221119070202.1407648-1-yangyingliang@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Syzbot reported a memory leak about skb:

unreferenced object 0xffff88810e144e00 (size 240):
  comm "syz-executor284", pid 3701, jiffies 4294952403 (age 12.620s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff83ab79a9>] __alloc_skb+0x1f9/0x270 net/core/skbuff.c:497
    [<ffffffff82a5cf64>] alloc_skb include/linux/skbuff.h:1267 [inline]
    [<ffffffff82a5cf64>] virtual_ncidev_write+0x24/0xe0 drivers/nfc/virtual_ncidev.c:116
    [<ffffffff815f6503>] do_loop_readv_writev fs/read_write.c:759 [inline]
    [<ffffffff815f6503>] do_loop_readv_writev fs/read_write.c:743 [inline]
    [<ffffffff815f6503>] do_iter_write+0x253/0x300 fs/read_write.c:863
    [<ffffffff815f66ed>] vfs_writev+0xdd/0x240 fs/read_write.c:934
    [<ffffffff815f68f6>] do_writev+0xa6/0x1c0 fs/read_write.c:977
    [<ffffffff848802d5>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
    [<ffffffff848802d5>] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
    [<ffffffff84a00087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd

In nci_rx_data_packet(), if we don't get a valid conn_info, we will return
directly but forget to release the skb.

Reported-by: syzbot+cdb9a427d1bc08815104@syzkaller.appspotmail.com
Fixes: 4aeee687 ("NFC: nci: Add dynamic logical connections support")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Link: https://lore.kernel.org/r/20221118082419.239475-1-liushixin2@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

In commit f11fe1da ("net/sched: Make NET_ACT_CT depends on NF_NAT"),
it fixed the build failure when NF_NAT is m and NET_ACT_CT is y by
adding depends on NF_NAT for NET_ACT_CT. However, it would also cause
NET_ACT_CT cannot be built without NF_NAT, which is not expected. This
patch fixes it by changing to use "(!NF_NAT || NF_NAT)" as the depend.

Fixes: f11fe1da ("net/sched: Make NET_ACT_CT depends on NF_NAT")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/b6386f28d1ba34721795fb776a91cbdabb203447.1668807183.git.lucien.xin@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

If phylink_of_phy_connect() fails, the port should be disabled.
If sparx5_serdes_set()/phy_power_on() fails, the port should be
disabled and the phylink should be stopped and disconnected.

Fixes: 946e7fd5 ("net: sparx5: add port module support")
Fixes: f3cad261 ("net: sparx5: add hostmode with phylink support")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Tested-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Steen Hegelund <steen.hegelund@microchip.com>
Link: https://lore.kernel.org/r/20221117125918.203997-1-liujian56@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The __ef100_hard_start_xmit() returns NETDEV_TX_OK without freeing skb
in error handling case, add dev_kfree_skb_any() to fix it.

Fixes: 51b35a45 ("sfc: skeleton EF100 PF driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/1668671409-10909-1-git-send-email-zhangchangzhong@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

acpi_evaluate_dsm() should be coupled with ACPI_FREE() to free the ACPI
memory, because we need to track the allocation of acpi_object when
ACPI_DBG_TRACK_ALLOCATIONS enabled, so use ACPI_FREE() instead of kfree().

Fixes: d38a648d ("net: wwan: iosm: fix memory leak in ipc_pcie_read_bios_cfg")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Link: https://lore.kernel.org/r/20221118062447.2324881-1-bobo.shaobowang@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>