- 26 Nov, 2021 30 commits
-
-
Oleksij Rempel authored
Current driver version is able to handle only one bridge at time. Configuring two bridges on two different ports would end up shorting this bridges by HW. To reproduce it: ip l a name br0 type bridge ip l a name br1 type bridge ip l s dev br0 up ip l s dev br1 up ip l s lan1 master br0 ip l s dev lan1 up ip l s lan2 master br1 ip l s dev lan2 up Ping on lan1 and get response on lan2, which should not happen. This happened, because current driver version is storing one global "Port VLAN Membership" and applying it to all ports which are members of any bridge. To solve this issue, we need to handle each port separately. This patch is dropping the global port member storage and calculating membership dynamically depending on STP state and bridge participation. Note: STP support was broken before this patch and should be fixed separately. Fixes: c2e86691 ("net: dsa: microchip: break KSZ9477 DSA driver into two files") Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by:
Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20211126123926.2981028-1-o.rempel@pengutronix.deSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Jakub Kicinski authored
Vladimir Oltean says: ==================== Fix broken PTP over IP on Ocelot switches Changes in v2: added patch 5, added Richard's ack for the whole series sans patch 5 which is new. Po Liu reported recently that timestamping PTP over IPv4 is broken using the felix driver on NXP LS1028A. This has been known for a while, of course, since it has always been broken. The reason is because IP PTP packets are currently treated as unknown IP multicast, which is not flooded to the CPU port in the ocelot driver design, so packets don't reach the ptp4l program. The series solves the problem by installing packet traps per port when the timestamping ioctl is called, depending on the RX filter selected (L2, L4 or both). ==================== Link: https://lore.kernel.org/r/20211126172845.3149260-1-vladimir.oltean@nxp.comSigned-off-by:
-
Vladimir Oltean authored
The driver doesn't support RX timestamping for non-PTP packets, but it declares that it does. Restrict the reported RX filters to PTP v2 over L2 and over L4. Fixes: 4e3b0468 ("net: mscc: PTP Hardware Clock (PHC) support") Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
-
Vladimir Oltean authored
IEEE 1588 support was declared too soon for the Ocelot switch. Out of reset, this switch does not apply any special treatment for PTP packets, i.e. when an event message is received, the natural tendency is to forward it by MAC DA/VLAN ID. This poses a problem when the ingress port is under a bridge, since user space application stacks (written primarily for endpoint ports, not switches) like ptp4l expect that PTP messages are always received on AF_PACKET / AF_INET sockets (depending on the PTP transport being used), and never being autonomously forwarded. Any forwarding, if necessary (for example in Transparent Clock mode) is handled in software by ptp4l. Having the hardware forward these packets too will cause duplicates which will confuse endpoints connected to these switches. So PTP over L2 barely works, in the sense that PTP packets reach the CPU port, but they reach it via flooding, and therefore reach lots of other unwanted destinations too. But PTP over IPv4/IPv6 does not work at all. This is because the Ocelot switch have a separate destination port mask for unknown IP multicast (which PTP over IP is) flooding compared to unknown non-IP multicast (which PTP over L2 is) flooding. Specifically, the driver allows the CPU port to be in the PGID_MC port group, but not in PGID_MCIPV4 and PGID_MCIPV6. There are several presentations from Allan Nielsen which explain that the embedded MIPS CPU on Ocelot switches is not very powerful at all, so every penny they could save by not allowing flooding to the CPU port module matters. Unknown IP multicast did not make it. The de facto consensus is that when a switch is PTP-aware and an application stack for PTP is running, switches should have some sort of trapping mechanism for PTP packets, to extract them from the hardware data path. This avoids both problems: (a) PTP packets are no longer flooded to unwanted destinations (b) PTP over IP packets are no longer denied from reaching the CPU since they arrive there via a trap and not via flooding It is not the first time when this change is attempted. Last time, the feedback from Allan Nielsen and Andrew Lunn was that the traps should not be installed by default, and that PTP-unaware switching may be desired for some use cases: https://patchwork.ozlabs.org/project/netdev/patch/20190813025214.18601-5-yangbo.lu@nxp.com/ To address that feedback, the present patch adds the necessary packet traps according to the RX filter configuration transmitted by user space through the SIOCSHWTSTAMP ioctl. Trapping is done via VCAP IS2, where we keep 5 filters, which are amended each time RX timestamping is enabled or disabled on a port: - 1 for PTP over L2 - 2 for PTP over IPv4 (UDP ports 319 and 320) - 2 for PTP over IPv6 (UDP ports 319 and 320) The cookie by which these filters (invisible to tc) are identified is strategically chosen such that it does not collide with the filters used for the ocelot-8021q tagging protocol by the Felix driver, or with the MRP traps set up by the Ocelot library. Other alternatives were considered, like patching user space to do something, but there are so many ways in which PTP packets could be made to reach the CPU, generically speaking, that "do what?" is a very valid question. The ptp4l program from the linuxptp stack already attempts to do something: it calls setsockopt(IP_ADD_MEMBERSHIP) (and PACKET_ADD_MEMBERSHIP, respectively) which translates in both cases into a dev_mc_add() on the interface, in the kernel: https://github.com/richardcochran/linuxptp/blob/v3.1.1/udp.c#L73 https://github.com/richardcochran/linuxptp/blob/v3.1.1/raw.c Reality shows that this is not sufficient in case the interface belongs to a switchdev driver, as dev_mc_add() does not show the intention to trap a packet to the CPU, but rather the intention to not drop it (it is strictly for RX filtering, same as promiscuous does not mean to send all traffic to the CPU, but to not drop traffic with unknown MAC DA). This topic is a can of worms in itself, and it would be great if user space could just stay out of it. On the other hand, setting up PTP traps privately within the driver is not new by any stretch of the imagination: https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c#L833 https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/dsa/hirschmann/hellcreek.c#L1050 https://elixir.bootlin.com/linux/v5.16-rc2/source/include/linux/dsa/sja1105.h#L21 So this is the approach taken here as well. The difference here being that we prepare and destroy the traps per port, dynamically at runtime, as opposed to driver init time, because apparently, PTP-unaware forwarding is a use case. Fixes: 4e3b0468 ("net: mscc: PTP Hardware Clock (PHC) support") Reported-by:Po Liu <po.liu@nxp.com> Signed-off-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Vladimir Oltean authored
As opposed to event messages (Sync, PdelayReq etc) which require timestamping, general messages (Announce, FollowUp etc) do not. In PTP they are part of different streams of data. IEEE 1588-2008 Annex D.2 "UDP port numbers" states that the UDP destination port assigned by IANA is 319 for event messages, and 320 for general messages. Yet the kernel seems to be missing the definition for general messages. This patch adds it. Signed-off-by:
-
Vladimir Oltean authored
VCAP (Versatile Content Aware Processor) is the TCAM-based engine behind tc flower offload on ocelot, among other things. The ingress port mask on which VCAP rules match is present as a bit field in the actual key of the rule. This means that it is possible for a rule to be shared among multiple source ports. When the rule is added one by one on each desired port, that the ingress port mask of the key must be edited and rewritten to hardware. But the API in ocelot_vcap.c does not allow for this. For one thing, ocelot_vcap_filter_add() and ocelot_vcap_filter_del() are not symmetric, because ocelot_vcap_filter_add() works with a preallocated and prepopulated filter and programs it to hardware, and ocelot_vcap_filter_del() does both the job of removing the specified filter from hardware, as well as kfreeing it. That is to say, the only option of editing a filter in place, which is to delete it, modify the structure and add it back, does not work because it results in use-after-free. This patch introduces ocelot_vcap_filter_replace, which trivially reprograms a VCAP entry to hardware, at the exact same index at which it existed before, without modifying any list or allocating any memory. Signed-off-by:
-
Vladimir Oltean authored
The ocelot driver, when asked to timestamp all receiving packets, 1588 v1 or NTP, says "nah, here's 1588 v2 for you". According to this discussion: https://patchwork.kernel.org/project/netdevbpf/patch/20211104133204.19757-8-martin.kaistra@linutronix.de/#24577647 drivers that downgrade from a wider request to a narrower response (or even a response where the intersection with the request is empty) are buggy, and should return -ERANGE instead. This patch fixes that. Fixes: 4e3b0468 ("net: mscc: PTP Hardware Clock (PHC) support") Suggested-by:
-
Jakub Kicinski authored
Guangbin Huang says: ==================== net: hns3: add some fixes for -net This series adds some fixes for the HNS3 ethernet driver. ==================== Link: https://lore.kernel.org/r/20211126120318.33921-1-huangguangbin2@huawei.comSigned-off-by:
-
Jie Wang authored
Currently, HNS3 driver doesn't clear the reset flags of components after successfully executing reset, it causes userspace info of "Components reset" and "Components not reset" is incorrect. So fix this problem by clear corresponding reset flag after reset process. Fixes: ddccc5e3 ("net: hns3: add support for triggering reset by ethtool") Signed-off-by:
Jie Wang <wangjie125@huawei.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
-
Hao Chen authored
Currently, when user queries page pool info by debugfs command "cat page_pool_info", the cnt of allocated page for page pool may be incorrect because of memory inconsistency problem caused by compiler optimization. So this patch uses READ_ONCE() to read value of pages_state_hold_cnt to fix this problem. Fixes: 850bfb91 ("net: hns3: debugfs add support dumping page pool info") Signed-off-by:
Hao Chen <chenhao288@hisilicon.com> Signed-off-by:
-
Hao Chen authored
When page pool is not enabled, its address value is still NULL and page pool should not be accessed, so add a check for it. Fixes: 850bfb91 ("net: hns3: debugfs add support dumping page pool info") Signed-off-by:
-
Guangbin Huang authored
When PF is set to multi-TCs and configured mapping relationship between priorities and TCs, the hardware will active these settings for this PF and its VFs. In this case when VF just uses one TC and its rx packets contain priority, and if the priority is not mapped to TC0, as other TCs of VF is not valid, hardware always put this kind of packets to the queue 0. It cause this kind of packets of VF can not be used RSS function. To fix this problem, set tc mode of all unused TCs of VF to the setting of TC0, then rx packet with priority which map to unused TC will be direct to TC0. Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by:
-
zhangyue authored
If the variable 'p_bit->flags' is always 0, the loop condition is always 0. The variable 'j' may be greater than or equal to 32. At this time, the array 'p_aeu->bits[32]' may be out of bound. Signed-off-by:
zhangyue <zhangyue1@kylinos.cn> Link: https://lore.kernel.org/r/20211125113610.273841-1-zhangyue1@kylinos.cnSigned-off-by:
-
Tony Lu authored
When applications call shutdown() with SHUT_RDWR in userspace, smc_close_active() calls kernel_sock_shutdown(), and it is called twice in smc_shutdown(). This fixes this by checking sk_state before do clcsock shutdown, and avoids missing the application's call of smc_shutdown(). Link: https://lore.kernel.org/linux-s390/1f67548e-cbf6-0dce-82b5-10288a4583bd@linux.ibm.com/ Fixes: 606a63c9 ("net/smc: Ensure the active closing peer first closes clcsock") Signed-off-by:
Tony Lu <tonylu@linux.alibaba.com> Reviewed-by:
Wen Gu <guwen@linux.alibaba.com> Acked-by:
Karsten Graul <kgraul@linux.ibm.com> Link: https://lore.kernel.org/r/20211126024134.45693-1-tonylu@linux.alibaba.comSigned-off-by:
-
Ziyang Xuan authored
Inject error before dev_hold(real_dev) in register_vlan_dev(), and execute the following testcase: ip link add dev dummy1 type dummy ip link add name dummy1.100 link dummy1 type vlan id 100 ip link del dev dummy1 When the dummy netdevice is removed, we will get a WARNING as following: ======================================================================= refcount_t: decrement hit 0; leaking memory. WARNING: CPU: 2 PID: 0 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0 and an endless loop of: ======================================================================= unregister_netdevice: waiting for dummy1 to become free. Usage count = -1073741824 That is because dev_put(real_dev) in vlan_dev_free() be called without dev_hold(real_dev) in register_vlan_dev(). It makes the refcnt of real_dev underflow. Move the dev_hold(real_dev) to vlan_dev_init() which is the call-back of ndo_init(). That makes dev_hold() and dev_put() for vlan's real_dev symmetrical. Fixes: 563bcbae ("net: vlan: fix a UAF in vlan_dev_real_dev()") Reported-by:
Petr Machata <petrm@nvidia.com> Suggested-by:
Ziyang Xuan <william.xuanziyang@huawei.com> Link: https://lore.kernel.org/r/20211126015942.2918542-1-william.xuanziyang@huawei.comSigned-off-by:
-
Jakub Kicinski authored
All the filter names are missing _PTP in them. Signed-off-by:
-
Julian Wiedmann authored
ethtool_set_coalesce() now uses both the .get_coalesce() and .set_coalesce() callbacks. But the check for their availability is buggy, so changing the coalesce settings on a device where the driver provides only _one_ of the callbacks results in a NULL pointer dereference instead of an -EOPNOTSUPP. Fix the condition so that the availability of both callbacks is ensured. This also matches the netlink code. Note that reproducing this requires some effort - it only affects the legacy ioctl path, and needs a specific combination of driver options: - have .get_coalesce() and .coalesce_supported but no .set_coalesce(), or - have .set_coalesce() but no .get_coalesce(). Here eg. ethtool doesn't cause the crash as it first attempts to call ethtool_get_coalesce() and bails out on error. Fixes: f3ccfda1 ("ethtool: extend coalesce setting uAPI with CQE mode") Cc: Yufeng Mo <moyufeng@huawei.com> Cc: Huazhong Tan <tanhuazhong@huawei.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Link: https://lore.kernel.org/r/20211126175543.28000-1-jwi@linux.ibm.comSigned-off-by:
-
Thadeu Lima de Souza Cascardo authored
Device permissions is S_IALLUGO, with many unnecessary bits. Remove them and also remove read and write permissions from group and others. Before the change: crwsrwsrwt 1 0 0 10, 125 Nov 25 13:59 /dev/virtual_nci After the change: crw------- 1 0 0 10, 125 Nov 25 14:05 /dev/virtual_nci Signed-off-by:
Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Reviewed-by:
Bongsu Jeon <bongsu.jeon@samsung.com> Link: https://lore.kernel.org/r/20211125141457.716921-1-cascardo@canonical.comSigned-off-by:
-
Davide Caratti authored
when the number of DRR classes decreases, the round-robin active list can contain elements that have already been freed in ets_qdisc_change(). As a consequence, it's possible to see a NULL dereference crash, caused by the attempt to call cl->qdisc->ops->peek(cl->qdisc) when cl->qdisc is NULL: BUG: kernel NULL pointer dereference, address: 0000000000000018 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 1 PID: 910 Comm: mausezahn Not tainted 5.16.0-rc1+ #475 Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014 RIP: 0010:ets_qdisc_dequeue+0x129/0x2c0 [sch_ets] Code: c5 01 41 39 ad e4 02 00 00 0f 87 18 ff ff ff 49 8b 85 c0 02 00 00 49 39 c4 0f 84 ba 00 00 00 49 8b ad c0 02 00 00 48 8b 7d 10 <48> 8b 47 18 48 8b 40 38 0f ae e8 ff d0 48 89 c3 48 85 c0 0f 84 9d RSP: 0000:ffffbb36c0b5fdd8 EFLAGS: 00010287 RAX: ffff956678efed30 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000002 RSI: ffffffff9b938dc9 RDI: 0000000000000000 RBP: ffff956678efed30 R08: e2f3207fe360129c R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000001 R12: ffff956678efeac0 R13: ffff956678efe800 R14: ffff956611545000 R15: ffff95667ac8f100 FS: 00007f2aa9120740(0000) GS:ffff95667b800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000018 CR3: 000000011070c000 CR4: 0000000000350ee0 Call Trace: <TASK> qdisc_peek_dequeued+0x29/0x70 [sch_ets] tbf_dequeue+0x22/0x260 [sch_tbf] __qdisc_run+0x7f/0x630 net_tx_action+0x290/0x4c0 __do_softirq+0xee/0x4f8 irq_exit_rcu+0xf4/0x130 sysvec_apic_timer_interrupt+0x52/0xc0 asm_sysvec_apic_timer_interrupt+0x12/0x20 RIP: 0033:0x7f2aa7fc9ad4 Code: b9 ff ff 48 8b 54 24 18 48 83 c4 08 48 89 ee 48 89 df 5b 5d e9 ed fc ff ff 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f3 0f 1e fa <53> 48 83 ec 10 48 8b 05 10 64 33 00 48 8b 00 48 85 c0 0f 85 84 00 RSP: 002b:00007ffe5d33fab8 EFLAGS: 00000202 RAX: 0000000000000002 RBX: 0000561f72c31460 RCX: 0000561f72c31720 RDX: 0000000000000002 RSI: 0000561f72c31722 RDI: 0000561f72c31720 RBP: 000000000000002a R08: 00007ffe5d33fa40 R09: 0000000000000014 R10: 0000000000000000 R11: 0000000000000246 R12: 0000561f7187e380 R13: 0000000000000000 R14: 0000000000000000 R15: 0000561f72c31460 </TASK> Modules linked in: sch_ets sch_tbf dummy rfkill iTCO_wdt intel_rapl_msr iTCO_vendor_support intel_rapl_common joydev virtio_balloon lpc_ich i2c_i801 i2c_smbus pcspkr ip_tables xfs libcrc32c crct10dif_pclmul crc32_pclmul crc32c_intel ahci libahci ghash_clmulni_intel serio_raw libata virtio_blk virtio_console virtio_net net_failover failover sunrpc dm_mirror dm_region_hash dm_log dm_mod CR2: 0000000000000018 Ensuring that 'alist' was never zeroed [1] was not sufficient, we need to remove from the active list those elements that are no more SP nor DRR. [1] https://lore.kernel.org/netdev/60d274838bf09777f0371253416e8af71360bc08.1633609148.git.dcaratti@redhat.com/ v3: fix race between ets_qdisc_change() and ets_qdisc_dequeue() delisting DRR classes beyond 'nbands' in ets_qdisc_change() with the qdisc lock acquired, thanks to Cong Wang. v2: when a NULL qdisc is found in the DRR active list, try to dequeue skb from the next list item. Reported-by:
Hangbin Liu <liuhangbin@gmail.com> Fixes: dcc68b4d ("net: sch_ets: Add a new Qdisc") Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Link: https://lore.kernel.org/r/7a5c496eed2d62241620bdbb83eb03fb9d571c99.1637762721.git.dcaratti@redhat.comSigned-off-by:
-
Yannick Vignon authored
The Tx queues were not disabled in situations where the driver needed to stop the interface to apply a new configuration. This could result in a kernel panic when doing any of the 3 following actions: * reconfiguring the number of queues (ethtool -L) * reconfiguring the size of the ring buffers (ethtool -G) * installing/removing an XDP program (ip l set dev ethX xdp) Prevent the panic by making sure netif_tx_disable is called when stopping an interface. Without this patch, the following kernel panic can be observed when doing any of the actions above: Unable to handle kernel paging request at virtual address ffff80001238d040 [....] Call trace: dwmac4_set_addr+0x8/0x10 dev_hard_start_xmit+0xe4/0x1ac sch_direct_xmit+0xe8/0x39c __dev_queue_xmit+0x3ec/0xaf0 dev_queue_xmit+0x14/0x20 [...] [ end trace 0000000000000002 ]--- Fixes: 5fabb012 ("net: stmmac: Add initial XDP support") Fixes: aa042f60 ("net: stmmac: Add support to Ethtool get/set ring parameters") Fixes: 0366f7e0 ("net: stmmac: add ethtool support for get/set channels") Signed-off-by:
Yannick Vignon <yannick.vignon@nxp.com> Link: https://lore.kernel.org/r/20211124154731.1676949-1-yannick.vignon@oss.nxp.comSigned-off-by:
-
Jakub Kicinski authored
Jakub Kicinski says: ==================== tls: splice_read fixes As I work my way to unlocked and zero-copy TLS Rx the obvious bugs in the splice_read implementation get harder and harder to ignore. This is to say the fixes here are discovered by code inspection, I'm not aware of anyone actually using splice_read. ==================== Link: https://lore.kernel.org/r/20211124232557.2039757-1-kuba@kernel.orgSigned-off-by:
-
Jakub Kicinski authored
Previous patch fixes overriding callbacks incorrectly. Triggering the crash in sendpage_locked would be more spectacular but it's hard to get to, so take the easier path of proving this is broken and call getname. We're currently getting IPv4 socket info on an IPv6 socket. Signed-off-by: -
Jakub Kicinski authored
We replace proto_ops whenever TLS is configured for RX. But our replacement also overrides sendpage_locked, which will crash unless TX is also configured. Similarly we plug both of those in for TLS_HW (NIC crypto offload) even tho TLS_HW has a completely different implementation for TX. Last but not least we always plug in something based on inet_stream_ops even though a few of the callbacks differ for IPv6 (getname, release, bind). Use a callback building method similar to what we do for struct proto. Fixes: c46234eb ("tls: RX path for ktls") Fixes: d4ffb02d ("net/tls: enable sk_msg redirect to tls socket egress") Signed-off-by:
-
Jakub Kicinski authored
Add tests for half-received and peeked records. Signed-off-by: -
Jakub Kicinski authored
recvmsg() will put peek()ed and partially read records onto the rx_list. splice_read() needs to consult that list otherwise it may miss data. Align with recvmsg() and also put partially-read records onto rx_list. tls_sw_advance_skb() is pretty pointless now and will be removed in net-next. Fixes: 692d7b5d ("tls: Fix recvmsg() to be able to peek across multiple records") Signed-off-by:
-
Jakub Kicinski authored
Make sure we correctly reject splicing non-data records. Signed-off-by: -
Jakub Kicinski authored
We don't support splicing control records. TLS 1.3 changes moved the record type check into the decrypt if(). The skb may already be decrypted and still be an alert. Note that decrypt_skb_update() is idempotent and updates ctx->decrypted so the if() is pointless. Reorder the check for decryption errors with the content type check while touching them. This part is not really a bug, because if decryption failed in TLS 1.3 content type will be DATA, and for TLS 1.2 it will be correct. Nevertheless its strange to touch output before checking if the function has failed. Fixes: fedf201e ("net: tls: Refactor control message handling on recv") Signed-off-by:
-
Jakub Kicinski authored
Test broken records. Signed-off-by: -
Jakub Kicinski authored
Add helpers for sending and receiving special record types. Signed-off-by: -
Jakub Kicinski authored
We have the same code 3 times, about to add a fourth copy. Signed-off-by:
-
- 25 Nov, 2021 10 commits
-
-
Dylan Hung authored
The issue happened randomly in runtime. The message "Link is Down" is popped but soon it recovered to "Link is Up". The "Link is Down" results from the incorrect read data for reading the PHY register via MDIO bus. The correct sequence for reading the data shall be: 1. fire the command 2. wait for command done (this step was missing) 3. wait for data idle 4. read data from data register Cc: stable@vger.kernel.org Fixes: f160e994 ("net: phy: Add mdio-aspeed") Reviewed-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
Dylan Hung <dylan_hung@aspeedtech.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20211125024432.15809-1-dylan_hung@aspeedtech.comSigned-off-by:
-
Jesse Brandeburg authored
Oleksandr brought a bug report where netpoll causes trace messages in the log on igb. Danielle brought this back up as still occurring, so we'll try again. [22038.710800] ------------[ cut here ]------------ [22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll [22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0 As Alex suggested, change the driver to return work_done at the exit of napi_poll, which should be safe to do in this driver because it is not polling multiple queues in this single napi context (multiple queues attached to one MSI-X vector). Several other drivers contain the same simple sequence, so I hope this will not create new problems. Fixes: 16eb8815 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance") Reported-by:
Oleksandr Natalenko <oleksandr@natalenko.name> Reported-by:
Danielle Ratson <danieller@nvidia.com> Suggested-by:
Alexander Duyck <alexander.duyck@gmail.com> Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by:
-
Jakub Kicinski authored
Karsten Graul says: ==================== net/smc: fixes 2021-11-24 Patch 1 from DaXing fixes a possible loop in smc_listen(). Patch 2 prevents a NULL pointer dereferencing while iterating over the lower network devices. ==================== Link: https://lore.kernel.org/r/20211124123238.471429-1-kgraul@linux.ibm.comSigned-off-by:
-
Guo DaXing authored
The kernel_listen function in smc_listen will fail when all the available ports are occupied. At this point smc->clcsock->sk->sk_data_ready has been changed to smc_clcsock_data_ready. When we call smc_listen again, now both smc->clcsock->sk->sk_data_ready and smc->clcsk_data_ready point to the smc_clcsock_data_ready function. The smc_clcsock_data_ready() function calls lsmc->clcsk_data_ready which now points to itself resulting in an infinite loop. This patch restores smc->clcsock->sk->sk_data_ready with the old value. Fixes: a60a2b1e ("net/smc: reduce active tcp_listen workers") Signed-off-by:
Guo DaXing <guodaxing@huawei.com> Acked-by:
-
Karsten Graul authored
Coverity reports a possible NULL dereferencing problem: in smc_vlan_by_tcpsk(): 6. returned_null: netdev_lower_get_next returns NULL (checked 29 out of 30 times). 7. var_assigned: Assigning: ndev = NULL return value from netdev_lower_get_next. 1623 ndev = (struct net_device *)netdev_lower_get_next(ndev, &lower); CID 1468509 (#1 of 1): Dereference null return value (NULL_RETURNS) 8. dereference: Dereferencing a pointer that might be NULL ndev when calling is_vlan_dev. 1624 if (is_vlan_dev(ndev)) { Remove the manual implementation and use netdev_walk_all_lower_dev() to iterate over the lower devices. While on it remove an obsolete function parameter comment. Fixes: cb9d43f6 ("net/smc: determine vlan_id of stacked net_device") Suggested-by: -
Jakub Kicinski authored
Marek Behún says: ==================== phylink resolve fixes With information from me and my nagging, Russell has produced two fixes for phylink, which add code that triggers another phylink_resolve() from phylink_resolve(), if certain conditions are met: interface is being changed or link is down and previous link was up These are needed because sometimes the PCS callbacks may provide stale values if link / speed / ... ==================== Link: https://lore.kernel.org/r/20211123154403.32051-1-kabel@kernel.orgSigned-off-by:
-
Russell King (Oracle) authored
On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following description: This register bit indicates when link was lost since the last read. For the current link status, read this register back-to-back. Thus to get current link state, we need to read the register twice. But doing that in the link change interrupt handler would lead to potentially ignoring link down events, which we really want to avoid. Thus this needs to be solved in phylink's resolve, by retriggering another resolve in the event when PCS reports link down and previous link was up, and by re-reading PCS state if the previous link was down. The wrong value is read when phylink requests change from sgmii to 2500base-x mode, and link won't come up. This fixes the bug. Fixes: 9525ae83 ("phylink: add phylink infrastructure") Signed-off-by:
Marek Behún <kabel@kernel.org> Signed-off-by:
-
Russell King (Oracle) authored
On PHY state change the phylink_resolve() function can read stale information from the MAC and report incorrect link speed and duplex to the kernel message log. Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell 88E6393X switch: - PHY driver triggers state change due to PHY interface mode being changed from 10gbase-r to 2500base-x due to copper change in speed from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed its interface to the host, or the interrupt about loss of SerDes link hadn't arrived yet (there can be a delay of several milliseconds for this), so we still think that the 10gbase-r mode is up - phylink_resolve() - phylink_mac_pcs_get_state() - this fills in speed=10g link=up - interface mode is updated to 2500base-x but speed is left at 10Gbps - phylink_major_config() - interface is changed to 2500base-x - phylink_link_up() - mv88e6xxx_mac_link_up() - .port_set_speed_duplex() - speed is set to 10Gbps - reports "Link is Up - 10Gbps/Full" to dmesg Afterwards when the interrupt finally arrives for mv88e6xxx, another resolve is forced in which we get the correct speed from phylink_mac_pcs_get_state(), but since the interface is not being changed anymore, we don't call phylink_major_config() but only phylink_mac_config(), which does not set speed/duplex anymore. To fix this, we need to force the link down and trigger another resolve on PHY interface change event. Fixes: 9525ae83 ("phylink: add phylink infrastructure") Signed-off-by: -
Heiner Kallweit authored
Usage of phy_ethtool_get_link_ksettings() in the link status change handler isn't needed, and in combination with the referenced change it results in a deadlock. Simply remove the call and replace it with direct access to phydev->speed. The duplex argument of lan743x_phy_update_flowcontrol() isn't used and can be removed. Fixes: c10a485c ("phy: phy_ethtool_ksettings_get: Lock the phy for consistency") Reported-by:
Alessandro B Maurici <abmaurici@gmail.com> Tested-by:
Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
-
Eric Dumazet authored
While testing BIG TCP patch series, I was expecting that TCP_RR workloads with 80KB requests/answers would send one 80KB TSO packet, then being received as a single GRO packet. It turns out this was not happening, and the root cause was that cubic Hystart ACK train was triggering after a few (2 or 3) rounds of RPC. Hystart was wrongly setting CWND/SSTHRESH to 30, while my RPC needed a budget of ~20 segments. Ideally these TCP_RR flows should not exit slow start. Cubic Hystart should reset itself at each round, instead of assuming every TCP flow is a bulk one. Note that even after this patch, Hystart can still trigger, depending on scheduling artifacts, but at a higher CWND/SSTHRESH threshold, keeping optimal TSO packet sizes. Tested: ip link set dev eth0 gro_ipv6_max_size 131072 gso_ipv6_max_size 131072 nstat -n; netperf -H ... -t TCP_RR -l 5 -- -r 80000,80000 -K cubic; nstat|egrep "Ip6InReceives|Hystart|Ip6OutRequests" Before: 8605 Ip6InReceives 87541 0.0 Ip6OutRequests 129496 0.0 TcpExtTCPHystartTrainDetect 1 0.0 TcpExtTCPHystartTrainCwnd 30 0.0 After: 8760 Ip6InReceives 88514 0.0 Ip6OutRequests 87975 0.0 Fixes: ae27e98a ("[TCP] CUBIC v2.3") Co-developed-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Yuchung Cheng <ycheng@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Link: https://lore.kernel.org/r/20211123202535.1843771-1-eric.dumazet@gmail.comSigned-off-by:
-
