- 23 Mar, 2019 40 commits
-
-
Michael Chan authored
[ Upstream commit 67681d02 ] The logic that polls for the firmware message response uses a shorter sleep interval for the first few passes. But there was a typo so it was using the wrong counter (larger counter) for these short sleep passes. The result is a slightly shorter timeout period for these firmware messages than intended. Fix it by using the proper counter. Fixes: 9751e8e7 ("bnxt_en: reduce timeout on initial HWRM calls") Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Jiong Wang authored
[ Upstream commit f036ebd9 ] NFP BPF JIT compiler is doing a couple of small optimizations when jitting ALU imm instructions, some of these optimizations could save code-gen, for example: A & -1 = A A | 0 = A A ^ 0 = A However, for ALU32, high 32-bit of the 64-bit register should still be cleared according to ISA semantics. Fixes: cd7df56e ("nfp: add BPF to NFP code translator") Reviewed-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
Jiong Wang <jiong.wang@netronome.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Jiong Wang authored
[ Upstream commit 71c19024 ] The intended optimization should be A ^ 0 = A, not A ^ -1 = A. Fixes: cd7df56e ("nfp: add BPF to NFP code translator") Reviewed-by:
-
Vadim Lomovtsev authored
[ Upstream commit 7db730d9 ] The rx_set_mode invokes number of messages to be send to PF for receive mode configuration. In case if there any issues we need to stop sending messages and release allocated memory. This commit is to implement check of nicvf_msg_send_to_pf() result. Signed-off-by:
Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by:
-
Vadim Lomovtsev authored
[ Upstream commit 0dd563b9 ] At the end of NIC VF initialization VF sends CFG_DONE message to PF without using nicvf_msg_send_to_pf routine. This potentially could re-write data in mailbox. This commit is to implement common way of sending CFG_DONE message by the same way with other configuration messages by using nicvf_send_msg_to_pf() routine. Signed-off-by:
-
Alban Crequy authored
[ Upstream commit 7c0cdf0b ] trie_delete_elem() was deleting an entry even though it was not matching if the prefixlen was correct. This patch adds a check on matchlen. Reproducer: $ sudo bpftool map create /sys/fs/bpf/mylpm type lpm_trie key 8 value 1 entries 128 name mylpm flags 1 $ sudo bpftool map update pinned /sys/fs/bpf/mylpm key hex 10 00 00 00 aa bb cc dd value hex 01 $ sudo bpftool map dump pinned /sys/fs/bpf/mylpm key: 10 00 00 00 aa bb cc dd value: 01 Found 1 element $ sudo bpftool map delete pinned /sys/fs/bpf/mylpm key hex 10 00 00 00 ff ff ff ff $ echo $? 0 $ sudo bpftool map dump pinned /sys/fs/bpf/mylpm Found 0 elements A similar reproducer is added in the selftests. Without the patch: $ sudo ./tools/testing/selftests/bpf/test_lpm_map test_lpm_map: test_lpm_map.c:485: test_lpm_delete: Assertion `bpf_map_delete_elem(map_fd, key) == -1 && errno == ENOENT' failed. Aborted With the patch: test_lpm_map runs without errors. Fixes: e454cf59 ("bpf: Implement map_delete_elem for BPF_MAP_TYPE_LPM_TRIE") Cc: Craig Gallek <kraig@google.com> Signed-off-by:
Alban Crequy <alban@kinvolk.io> Acked-by:
Craig Gallek <kraig@google.com> Signed-off-by:
-
Li RongQing authored
[ Upstream commit 17407715 ] genlmsg_reply can fail, so propagate its return code Signed-off-by:
Li RongQing <lirongqing@baidu.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 6321aa19 ] clang warns about overflowing the data[] member in the struct pnpipehdr: net/phonet/pep.c:295:8: warning: array index 4 is past the end of the array (which contains 1 element) [-Warray-bounds] if (hdr->data[4] == PEP_IND_READY) ^ ~ include/net/phonet/pep.h:66:3: note: array 'data' declared here u8 data[1]; Using a flexible array member at the end of the struct avoids the warning, but since we cannot have a flexible array member inside of the union, each index now has to be moved back by one, which makes it a little uglier. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Rémi Denis-Courmont <remi@remlab.net> Signed-off-by:
-
Vineet Gupta authored
[ Upstream commit 7b2e932f ] The first release of core4 (0x54) was dual issue only (HS4x). Newer releases allow hardware to be configured as single issue (HS3x) or dual issue. Prevent accessing a HS4x only aux register in HS3x, which otherwise leads to illegal instruction exceptions Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Vineet Gupta authored
[ Upstream commit e494239a ] There's a hardware bug which affects the HSDK platform, triggered by micro-ops for auto-saving regfile on taken interrupt. The workaround is to inhibit autosave. Signed-off-by:
-
Vineet Gupta authored
[ Upstream commit d5e3c55e ] Newer ARC gcc handles lp_start, lp_end in a different way and doesn't like them in the clobber list. Signed-off-by:
-
Eugeniy Paltsev authored
[ Upstream commit f8a15f97 ] ARCv2 optimized memcpy uses PREFETCHW instruction for prefetching the next cache line but doesn't ensure that the line is not past the end of the buffer. PRETECHW changes the line ownership and marks it dirty, which can cause data corruption if this area is used for DMA IO. Fix the issue by avoiding the PREFETCHW. This leads to performance degradation but it is OK as we'll introduce new memcpy implementation optimized for unaligned memory access using. We also cut off all PREFETCH instructions at they are quite useless here: * we call PREFETCH right before LOAD instruction call. * we copy 16 or 32 bytes of data (depending on CONFIG_ARC_HAS_LL64) in a main logical loop. so we call PREFETCH 4 times (or 2 times) for each L1 cache line (in case of 64B L1 cache Line which is default case). Obviously this is not optimal. Signed-off-by:
Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by:
-
Jeff Kirsher authored
[ Upstream commit 156a67a9 ] The enabling L3/L4 filtering for transmit switched packets for all devices caused unforeseen issue on older devices when trying to send UDP traffic in an ordered sequence. This bit was originally intended for X550 devices, which supported this feature, so limit the scope of this bit to only X550 devices. Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
-
Darrick J. Wong authored
[ Upstream commit 1062af92 ] tmpfs has a peculiarity of accounting hard links as if they were separate inodes: so that when the number of inodes is limited, as it is by default, a user cannot soak up an unlimited amount of unreclaimable dcache memory just by repeatedly linking a file. But when v3.11 added O_TMPFILE, and the ability to use linkat() on the fd, we missed accommodating this new case in tmpfs: "df -i" shows that an extra "inode" remains accounted after the file is unlinked and the fd closed and the actual inode evicted. If a user repeatedly links tmpfiles into a tmpfs, the limit will be hit (ENOSPC) even after they are deleted. Just skip the extra reservation from shmem_link() in this case: there's a sense in which this first link of a tmpfile is then cheaper than a hard link of another file, but the accounting works out, and there's still good limiting, so no need to do anything more complicated. Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1902182134370.7035@eggly.anvils Fixes: f4e0c30c ("allow the temp files created by open() to be linked to") Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
Hugh Dickins <hughd@google.com> Reported-by:
Matej Kupljen <matej.kupljen@gmail.com> Acked-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Michal Hocko authored
[ Upstream commit 6ea183d6 ] Since for_each_cpu(cpu, mask) added by commit 2d3854a3 ("cpumask: introduce new API, without changing anything") did not evaluate the mask argument if NR_CPUS == 1 due to CONFIG_SMP=n, lru_add_drain_all() is hitting WARN_ON() at __flush_work() added by commit 4d43d395 ("workqueue: Try to catch flush_work() without INIT_WORK().") by unconditionally calling flush_work() [1]. Workaround this issue by using CONFIG_SMP=n specific lru_add_drain_all implementation. There is no real need to defer the implementation to the workqueue as the draining is going to happen on the local cpu. So alias lru_add_drain_all to lru_add_drain which does all the necessary work. [akpm@linux-foundation.org: fix various build warnings] [1] https://lkml.kernel.org/r/18a30387-6aa5-6123-e67c-57579ecc3f38@roeck-us.net Link: http://lkml.kernel.org/r/20190213124334.GH4525@dhcp22.suse.czSigned-off-by:
Michal Hocko <mhocko@suse.com> Reported-by:
Guenter Roeck <linux@roeck-us.net> Debugged-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Tejun Heo <tj@kernel.org> Signed-off-by:
-
Russell King authored
[ Upstream commit a8fef9ba ] Booting 4.20 on SolidRun Clearfog issues this warning with DMA API debug enabled: WARNING: CPU: 0 PID: 555 at kernel/dma/debug.c:1230 check_sync+0x514/0x5bc mvneta f1070000.ethernet: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x000000002dd7dc00] [size=240 bytes] Modules linked in: ahci mv88e6xxx dsa_core xhci_plat_hcd xhci_hcd devlink armada_thermal marvell_cesa des_generic ehci_orion phy_armada38x_comphy mcp3021 spi_orion evbug sfp mdio_i2c ip_tables x_tables CPU: 0 PID: 555 Comm: bridge-network- Not tainted 4.20.0+ #291 Hardware name: Marvell Armada 380/385 (Device Tree) [<c0019638>] (unwind_backtrace) from [<c0014888>] (show_stack+0x10/0x14) [<c0014888>] (show_stack) from [<c07f54e0>] (dump_stack+0x9c/0xd4) [<c07f54e0>] (dump_stack) from [<c00312bc>] (__warn+0xf8/0x124) [<c00312bc>] (__warn) from [<c00313b0>] (warn_slowpath_fmt+0x38/0x48) [<c00313b0>] (warn_slowpath_fmt) from [<c00b0370>] (check_sync+0x514/0x5bc) [<c00b0370>] (check_sync) from [<c00b04f8>] (debug_dma_sync_single_range_for_cpu+0x6c/0x74) [<c00b04f8>] (debug_dma_sync_single_range_for_cpu) from [<c051bd14>] (mvneta_poll+0x298/0xf58) [<c051bd14>] (mvneta_poll) from [<c0656194>] (net_rx_action+0x128/0x424) [<c0656194>] (net_rx_action) from [<c000a230>] (__do_softirq+0xf0/0x540) [<c000a230>] (__do_softirq) from [<c00386e0>] (irq_exit+0x124/0x144) [<c00386e0>] (irq_exit) from [<c009b5e0>] (__handle_domain_irq+0x58/0xb0) [<c009b5e0>] (__handle_domain_irq) from [<c03a63c4>] (gic_handle_irq+0x48/0x98) [<c03a63c4>] (gic_handle_irq) from [<c0009a10>] (__irq_svc+0x70/0x98) ... This appears to be caused by mvneta_rx_hwbm() calling dma_sync_single_range_for_cpu() with the wrong struct device pointer, as the buffer manager device pointer is used to map and unmap the buffer. Fix this. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Thierry Reding authored
[ Upstream commit 94d9b933 ] Commit 48299769 ("ARM: tegra: Fix unit_address_vs_reg DTC warnings for /memory") inadventently broke device tree ABI by adding a unit- address to the "/memory" node because the device tree compiler flagged the missing unit-address as a warning. Tegra124 Chromebooks (a.k.a. Nyan) use a bootloader that relies on the full name of the memory node in device tree being exactly "/memory". It can be argued whether this was a good decision or not, and some other bootloaders (such as U-Boot) do accept a unit-address in the name of the node, but the device tree is an ABI and we can't break existing setups just because the device tree compiler considers it bad practice to omit the unit-address nowadays. This partially reverts the offending commit and restores device tree ABI compatibility. Fixes: 48299769 ("ARM: tegra: Fix unit_address_vs_reg DTC warnings for /memory") Reported-by:
Tristan Bastian <tristan-c.bastian@gmx.de> Signed-off-by:
Thierry Reding <treding@nvidia.com> Tested-by:
-
Vladimir Murzin authored
[ Upstream commit 74698f69 ] Updates to the GIC architecture allow ID_AA64PFR0_EL1.GIC to have values other than 0 or 1. At the moment, Linux is quite strict in the way it handles this field at early boot stage (cpufeature is fine) and will refuse to use the system register CPU interface if it doesn't find the value 1. Fixes: 021f6537 ("irqchip: gic-v3: Initial support for GICv3") Reported-by:
Chase Conklin <Chase.Conklin@arm.com> Reviewed-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Thomas Petazzoni authored
[ Upstream commit 6fc97917 ] Commit 3b799199 ("ARM: dts: armada-370-xp: update NAND node with new bindings") updated some Marvell Armada DT description to use the new NAND controller bindings, but did it incorrectly for a number of boards: armada-xp-gp, armada-xp-db and armada-xp-lenovo-ix4-300d. Due to this, the NAND is no longer detected on those platforms. This commit fixes that by properly using the new NAND DT binding. This commit was runtime-tested on Armada XP GP, the two other platforms are only compile-tested. Fixes: 3b799199 ("ARM: dts: armada-370-xp: update NAND node with new bindings") Cc: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by:
Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by:
-
Michal Kalderon authored
[ Upstream commit 8be3dadf ] The ll2 forwards all syn packets to the driver without validating the mac address. Add validation check in the driver's iWARP listener flow and drop the packet if it isn't intended for the device. Signed-off-by:
Ariel Elior <ariel.elior@marvell.com> Signed-off-by:
Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by:
-
Michal Kalderon authored
[ Upstream commit 9addc927 ] The assumption that the maximum size of a syn packet is 128 bytes is wrong. Tunneling headers were not accounted for. Allocate buffers large enough for mtu. Signed-off-by:
-
Bard liao authored
[ Upstream commit 304017d3 ] Topology resources are no longer needed if any element failed to load. Signed-off-by:
Bard liao <yung-chuan.liao@linux.intel.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Rayagonda Kokatanur authored
[ Upstream commit d7bf31a0 ] RING_CONTROL reg was not written due to wrong address, hence all the subsequent ring flush was timing out. Fixes: a371c10e ("mailbox: bcm-flexrm-mailbox: Fix FlexRM ring flush sequence") Signed-off-by:
Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Signed-off-by:
Ray Jui <ray.jui@broadcom.com> Reviewed-by:
Scott Branden <scott.branden@broadcom.com> Signed-off-by:
Jassi Brar <jaswinder.singh@linaro.org> Signed-off-by:
-
Tobias Brunner authored
[ Upstream commit 660899dd ] After moving an XFRM interface to another namespace it stays associated with the original namespace (net in `struct xfrm_if` and the list keyed with `xfrmi_net_id`), allowing processes in the new namespace to use SAs/policies that were created in the original namespace. For instance, this allows a keying daemon in one namespace to establish IPsec SAs for other namespaces without processes there having access to the keys or IKE credentials. This worked fine for outbound traffic, however, for inbound traffic the lookup for the interfaces and the policies used the incorrect namespace (the one the XFRM interface was moved to). Fixes: f203b76d ("xfrm: Add virtual xfrm interfaces") Signed-off-by:
Tobias Brunner <tobias@strongswan.org> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Alexey Khoroshilov authored
[ Upstream commit e928b5d6 ] If mv643xx_eth_shared_of_probe() fails, mv643xx_eth_shared_probe() leaves clk enabled. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Beniamino Galvani authored
[ Upstream commit 97dc47a1 ] The 1199:68C0 USB ID is reused by Sierra WP7607 which requires the DTR quirk to be detected. Apply QMI_QUIRK_SET_DTR unconditionally as already done for other IDs shared between different devices. Signed-off-by:
Beniamino Galvani <bgalvani@redhat.com> Acked-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Martin Blumenstingl authored
[ Upstream commit c17abcfa ] Fix the mismatch between the "sdxc_d13_1_a" pin group definition from meson8b_cbus_groups and the entry in sdxc_a_groups ("sdxc_d0_13_1_a"). This makes it possible to use "sdxc_d13_1_a" in device-tree files to route the MMC data 1..3 pins to GPIOX_1..3. Fixes: 0fefcb68 ("pinctrl: Add support for Meson8b") Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit c3152ec4 ] We assume in the bcm_sf2 driver that the DSA master network device supports ethtool_ops::{get,set}_wol operations, which is not a given. Avoid de-referencing potentially non-existent function pointers and check them as we should. Fixes: 96e65d7f ("net: dsa: bcm_sf2: add support for Wake-on-LAN") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit a40061ea ] SYSTEMPORT has its RXCHK parser block that attempts to validate the packet structures, unfortunately setting the L2 header check bit will cause Bridge PDUs (BPDUs) to be incorrectly rejected because they look like LLC/SNAP packets with a non-IPv4 or non-IPv6 Ethernet Type. Fixes: 4e8aedfe78c7 ("net: systemport: Turn on offloads by default") Signed-off-by:
-
Anoob Soman authored
[ Upstream commit 79edd00d ] When a target sends Check Condition, whilst initiator is busy xmiting re-queued data, could lead to race between iscsi_complete_task() and iscsi_xmit_task() and eventually crashing with the following kernel backtrace. [3326150.987523] ALERT: BUG: unable to handle kernel NULL pointer dereference at 0000000000000078 [3326150.987549] ALERT: IP: [<ffffffffa05ce70d>] iscsi_xmit_task+0x2d/0xc0 [libiscsi] [3326150.987571] WARN: PGD 569c8067 PUD 569c9067 PMD 0 [3326150.987582] WARN: Oops: 0002 [#1] SMP [3326150.987593] WARN: Modules linked in: tun nfsv3 nfs fscache dm_round_robin [3326150.987762] WARN: CPU: 2 PID: 8399 Comm: kworker/u32:1 Tainted: G O 4.4.0+2 #1 [3326150.987774] WARN: Hardware name: Dell Inc. PowerEdge R720/0W7JN5, BIOS 2.5.4 01/22/2016 [3326150.987790] WARN: Workqueue: iscsi_q_13 iscsi_xmitworker [libiscsi] [3326150.987799] WARN: task: ffff8801d50f3800 ti: ffff8801f5458000 task.ti: ffff8801f5458000 [3326150.987810] WARN: RIP: e030:[<ffffffffa05ce70d>] [<ffffffffa05ce70d>] iscsi_xmit_task+0x2d/0xc0 [libiscsi] [3326150.987825] WARN: RSP: e02b:ffff8801f545bdb0 EFLAGS: 00010246 [3326150.987831] WARN: RAX: 00000000ffffffc3 RBX: ffff880282d2ab20 RCX: ffff88026b6ac480 [3326150.987842] WARN: RDX: 0000000000000000 RSI: 00000000fffffe01 RDI: ffff880282d2ab20 [3326150.987852] WARN: RBP: ffff8801f545bdc8 R08: 0000000000000000 R09: 0000000000000008 [3326150.987862] WARN: R10: 0000000000000000 R11: 000000000000fe88 R12: 0000000000000000 [3326150.987872] WARN: R13: ffff880282d2abe8 R14: ffff880282d2abd8 R15: ffff880282d2ac08 [3326150.987890] WARN: FS: 00007f5a866b4840(0000) GS:ffff88028a640000(0000) knlGS:0000000000000000 [3326150.987900] WARN: CS: e033 DS: 0000 ES: 0000 CR0: 0000000080050033 [3326150.987907] WARN: CR2: 0000000000000078 CR3: 0000000070244000 CR4: 0000000000042660 [3326150.987918] WARN: Stack: [3326150.987924] WARN: ffff880282d2ad58 ffff880282d2ab20 ffff880282d2abe8 ffff8801f545be18 [3326150.987938] WARN: ffffffffa05cea90 ffff880282d2abf8 ffff88026b59cc80 ffff88026b59cc00 [3326150.987951] WARN: ffff88022acf32c0 ffff880289491800 ffff880255a80800 0000000000000400 [3326150.987964] WARN: Call Trace: [3326150.987975] WARN: [<ffffffffa05cea90>] iscsi_xmitworker+0x2f0/0x360 [libiscsi] [3326150.987988] WARN: [<ffffffff8108862c>] process_one_work+0x1fc/0x3b0 [3326150.987997] WARN: [<ffffffff81088f95>] worker_thread+0x2a5/0x470 [3326150.988006] WARN: [<ffffffff8159cad8>] ? __schedule+0x648/0x870 [3326150.988015] WARN: [<ffffffff81088cf0>] ? rescuer_thread+0x300/0x300 [3326150.988023] WARN: [<ffffffff8108ddf5>] kthread+0xd5/0xe0 [3326150.988031] WARN: [<ffffffff8108dd20>] ? kthread_stop+0x110/0x110 [3326150.988040] WARN: [<ffffffff815a0bcf>] ret_from_fork+0x3f/0x70 [3326150.988048] WARN: [<ffffffff8108dd20>] ? kthread_stop+0x110/0x110 [3326150.988127] ALERT: RIP [<ffffffffa05ce70d>] iscsi_xmit_task+0x2d/0xc0 [libiscsi] [3326150.988138] WARN: RSP <ffff8801f545bdb0> [3326150.988144] WARN: CR2: 0000000000000078 [3326151.020366] WARN: ---[ end trace 1c60974d4678d81b ]--- Commit 6f8830f5 ("scsi: libiscsi: add lock around task lists to fix list corruption regression") introduced "taskqueuelock" to fix list corruption during the race, but this wasn't enough. Re-setting of conn->task to NULL, could race with iscsi_xmit_task(). iscsi_complete_task() { .... if (conn->task == task) conn->task = NULL; } conn->task in iscsi_xmit_task() could be NULL and so will be task. __iscsi_get_task(task) will crash (NullPtr de-ref), trying to access refcount. iscsi_xmit_task() { struct iscsi_task *task = conn->task; __iscsi_get_task(task); } This commit will take extra conn->session->back_lock in iscsi_xmit_task() to ensure iscsi_xmit_task() waits for iscsi_complete_task(), if iscsi_complete_task() wins the race. If iscsi_xmit_task() wins the race, iscsi_xmit_task() increments task->refcount (__iscsi_get_task) ensuring iscsi_complete_task() will not iscsi_free_task(). Signed-off-by:
Anoob Soman <anoob.soman@citrix.com> Signed-off-by:
Bob Liu <bob.liu@oracle.com> Acked-by:
Lee Duncan <lduncan@suse.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
David Howells authored
[ Upstream commit 822ad64d ] In the request_key() upcall mechanism there's a dependency loop by which if a key type driver overrides the ->request_key hook and the userspace side manages to lose the authorisation key, the auth key and the internal construction record (struct key_construction) can keep each other pinned. Fix this by the following changes: (1) Killing off the construction record and using the auth key instead. (2) Including the operation name in the auth key payload and making the payload available outside of security/keys/. (3) The ->request_key hook is given the authkey instead of the cons record and operation name. Changes (2) and (3) allow the auth key to naturally be cleaned up if the keyring it is in is destroyed or cleared or the auth key is unlinked. Fixes: 7ee02a316600 ("keys: Fix dependency loop between construction record and auth key") Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
James Morris <james.morris@microsoft.com> Signed-off-by:
-
David Howells authored
[ Upstream commit bb2ba2d7 ] Fix the creation of shortcuts for which the length of the index key value is an exact multiple of the machine word size. The problem is that the code that blanks off the unused bits of the shortcut value malfunctions if the number of bits in the last word equals machine word size. This is due to the "<<" operator being given a shift of zero in this case, and so the mask that should be all zeros is all ones instead. This causes the subsequent masking operation to clear everything rather than clearing nothing. Ordinarily, the presence of the hash at the beginning of the tree index key makes the issue very hard to test for, but in this case, it was encountered due to a development mistake that caused the hash output to be either 0 (keyring) or 1 (non-keyring) only. This made it susceptible to the keyctl/unlink/valid test in the keyutils package. The fix is simply to skip the blanking if the shift would be 0. For example, an index key that is 64 bits long would produce a 0 shift and thus a 'blank' of all 1s. This would then be inverted and AND'd onto the index_key, incorrectly clearing the entire last word. Fixes: 3cb98950 ("Add a generic associative array implementation.") Signed-off-by:
-
Robin Murphy authored
[ Upstream commit fc67e6f1 ] Installing the appropriate non-IOMMU DMA ops in arm_iommu_detch_device() serves the case where IOMMU-aware drivers choose to control their own mapping but still make DMA API calls, however it also affects the case when the arch code itself tears down the mapping upon driver unbinding, where the ops now get left in place and can inhibit arch_setup_dma_ops() on subsequent re-probe attempts. Fix the latter case by making sure that arch_teardown_dma_ops() cleans up whenever the ops were automatically installed by its counterpart. Reported-by:
Tobias Jakobi <tjakobi@math.uni-bielefeld.de> Reported-by:
Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 1874619a "ARM: dma-mapping: Set proper DMA ops in arm_iommu_detach_device()" Tested-by:
Robin Murphy <robin.murphy@arm.com> Signed-off-by:
-
Sean Tranchetti authored
[ Upstream commit fc2d5cfd ] Attempting to avoid cloning the skb when broadcasting by inflating the refcount with sock_hold/sock_put while under RCU lock is dangerous and violates RCU principles. It leads to subtle race conditions when attempting to free the SKB, as we may reference sockets that have already been freed by the stack. Unable to handle kernel paging request at virtual address 6b6b6b6b6b6c4b [006b6b6b6b6b6c4b] address between user and kernel address ranges Internal error: Oops: 96000004 [#1] PREEMPT SMP task: fffffff78f65b380 task.stack: ffffff8049a88000 pc : sock_rfree+0x38/0x6c lr : skb_release_head_state+0x6c/0xcc Process repro (pid: 7117, stack limit = 0xffffff8049a88000) Call trace: sock_rfree+0x38/0x6c skb_release_head_state+0x6c/0xcc skb_release_all+0x1c/0x38 __kfree_skb+0x1c/0x30 kfree_skb+0xd0/0xf4 pfkey_broadcast+0x14c/0x18c pfkey_sendmsg+0x1d8/0x408 sock_sendmsg+0x44/0x60 ___sys_sendmsg+0x1d0/0x2a8 __sys_sendmsg+0x64/0xb4 SyS_sendmsg+0x34/0x4c el0_svc_naked+0x34/0x38 Kernel panic - not syncing: Fatal exception Suggested-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
Sean Tranchetti <stranche@codeaurora.org> Signed-off-by:
-
Alexei Starovoitov authored
[ Upstream commit 3defaf2f ] Lockdep warns about false positive: [ 11.211460] ------------[ cut here ]------------ [ 11.211936] DEBUG_LOCKS_WARN_ON(depth <= 0) [ 11.211985] WARNING: CPU: 0 PID: 141 at ../kernel/locking/lockdep.c:3592 lock_release+0x1ad/0x280 [ 11.213134] Modules linked in: [ 11.214954] RIP: 0010:lock_release+0x1ad/0x280 [ 11.223508] Call Trace: [ 11.223705] <IRQ> [ 11.223874] ? __local_bh_enable+0x7a/0x80 [ 11.224199] up_read+0x1c/0xa0 [ 11.224446] do_up_read+0x12/0x20 [ 11.224713] irq_work_run_list+0x43/0x70 [ 11.225030] irq_work_run+0x26/0x50 [ 11.225310] smp_irq_work_interrupt+0x57/0x1f0 [ 11.225662] irq_work_interrupt+0xf/0x20 since rw_semaphore is released in a different task vs task that locked the sema. It is expected behavior. Fix the warning with up_read_non_owner() and rwsem_release() annotation. Fixes: bae77c5e ("bpf: enable stackmap with build_id in nmi context") Signed-off-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Willem de Bruijn authored
[ Upstream commit b90efd22 ] bpf_skb_change_proto and bpf_skb_adjust_room change skb header length. For GSO packets they adjust gso_size to maintain the same MTU. The gso size can only be safely adjusted on bytestream protocols. Commit d02f51cb ("bpf: fix bpf_skb_adjust_net/bpf_skb_proto_xlat to deal with gso sctp skbs") excluded SKB_GSO_SCTP. Since then type SKB_GSO_UDP_L4 has been added, whose contents are one gso_size unit per datagram. Also exclude these. Move from a blacklist to a whitelist check to future proof against additional such new GSO types, e.g., for fraglist based GRO. Fixes: bec1f6f6 ("udp: generate gso with UDP_SEGMENT") Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Dietmar Eggemann authored
[ Upstream commit 1b5ba350 ] Arm TC2 fails cpu hotplug stress test. This issue was tracked down to a missing copy of the new affinity cpumask for the vexpress-spc interrupt into struct irq_common_data.affinity when the interrupt is migrated in migrate_one_irq(). Fix it by replacing the arm specific hotplug cpu migration with the generic irq code. This is the counterpart implementation to commit 217d453d ("arm64: fix a migrating irq bug when hotplug cpu"). Tested with cpu hotplug stress test on Arm TC2 (multi_v7_defconfig plus CONFIG_ARM_BIG_LITTLE_CPUFREQ=y and CONFIG_ARM_VEXPRESS_SPC_CPUFREQ=y). The vexpress-spc interrupt (irq=22) on this board is affine to CPU0. Its affinity cpumask now changes correctly e.g. from 0 to 1-4 when CPU0 is hotplugged out. Suggested-by:
Dietmar Eggemann <dietmar.eggemann@arm.com> Acked-by:
-
Martin Willi authored
[ Upstream commit 09db5124 ] On ESP output, sk_wmem_alloc is incremented for the added padding if a socket is associated to the skb. When replying with TCP SYNACKs over IPsec, the associated sk is a casted request socket, only. Increasing sk_wmem_alloc on a request socket results in a write at an arbitrary struct offset. In the best case, this produces the following WARNING: WARNING: CPU: 1 PID: 0 at lib/refcount.c:102 esp_output_head+0x2e4/0x308 [esp4] refcount_t: addition on 0; use-after-free. CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.0.0-rc3 #2 Hardware name: Marvell Armada 380/385 (Device Tree) [...] [<bf0ff354>] (esp_output_head [esp4]) from [<bf1006a4>] (esp_output+0xb8/0x180 [esp4]) [<bf1006a4>] (esp_output [esp4]) from [<c05dee64>] (xfrm_output_resume+0x558/0x664) [<c05dee64>] (xfrm_output_resume) from [<c05d07b0>] (xfrm4_output+0x44/0xc4) [<c05d07b0>] (xfrm4_output) from [<c05956bc>] (tcp_v4_send_synack+0xa8/0xe8) [<c05956bc>] (tcp_v4_send_synack) from [<c0586ad8>] (tcp_conn_request+0x7f4/0x948) [<c0586ad8>] (tcp_conn_request) from [<c058c404>] (tcp_rcv_state_process+0x2a0/0xe64) [<c058c404>] (tcp_rcv_state_process) from [<c05958ac>] (tcp_v4_do_rcv+0xf0/0x1f4) [<c05958ac>] (tcp_v4_do_rcv) from [<c0598a4c>] (tcp_v4_rcv+0xdb8/0xe20) [<c0598a4c>] (tcp_v4_rcv) from [<c056eb74>] (ip_protocol_deliver_rcu+0x2c/0x2dc) [<c056eb74>] (ip_protocol_deliver_rcu) from [<c056ee6c>] (ip_local_deliver_finish+0x48/0x54) [<c056ee6c>] (ip_local_deliver_finish) from [<c056eecc>] (ip_local_deliver+0x54/0xec) [<c056eecc>] (ip_local_deliver) from [<c056efac>] (ip_rcv+0x48/0xb8) [<c056efac>] (ip_rcv) from [<c0519c2c>] (__netif_receive_skb_one_core+0x50/0x6c) [...] The issue triggers only when not using TCP syncookies, as for syncookies no socket is associated. Fixes: cac2661c ("esp4: Avoid skb_cow_data whenever possible") Fixes: 03e2a30f ("esp6: Avoid skb_cow_data whenever possible") Signed-off-by:
Martin Willi <martin@strongswan.org> Signed-off-by:
-
Andre Przywara authored
[ Upstream commit ee0b27a3 ] According to the manual the gate clock for MMC3 is at bit 11, and NAND1 is controlled by bit 12. Fix the gate bit definitions in the clock driver. Fixes: c6e6c96d ("clk: sunxi-ng: Add A31/A31s clocks") Signed-off-by:
Andre Przywara <andre.przywara@arm.com> Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
-
Eugene Loh authored
[ Upstream commit 6db2983c ] When checking for symbols with excessively long names, account for null terminating character. Fixes: f3462aa9 ("Kbuild: Handle longer symbols in kallsyms.c") Signed-off-by:
Eugene Loh <eugene.loh@oracle.com> Acked-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
-
