- 15 Apr, 2020 12 commits
-
-
Johan Jonker authored
The description below is already in use in 'rk3228-evb.dts', 'rk3229-xms6.dts' and 'rk3328.dtsi' but somehow never added to a document, so add "ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22" for ethernet-phy nodes on Rockchip platforms to 'ethernet-phy.yaml'. Signed-off-by:
Johan Jonker <jbx6244@gmail.com> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Colin Ian King authored
The variable err is being initialized with a value that is never read and it is being updated later with a new value. The initialization is redundant and can be removed. Addresses-Coverity: ("Unused value") Signed-off-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Jason Gunthorpe authored
Returning the error code via a 'int *ret' when the function returns a pointer is very un-kernely and causes gcc 10's static analysis to choke: net/rds/message.c: In function ‘rds_message_map_pages’: net/rds/message.c:358:10: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized] 358 | return ERR_PTR(ret); Use a typical ERR_PTR return instead. Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Acked-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
-
Vladimir Oltean authored
To rehash a previous explanation given in commit 1c44ce56 ("net: mscc: ocelot: fix vlan_filtering when enslaving to bridge before link is up"), the switch driver operates the in a mode where a single VLAN can be transmitted as untagged on a particular egress port. That is the "native VLAN on trunk port" use case. The configuration for this native VLAN is driven in 2 ways: - Set the egress port rewriter to strip the VLAN tag for the native VID (as it is egress-untagged, after all). - Configure the ingress port to drop untagged and priority-tagged traffic, if there is no native VLAN. The intention of this setting is that a trunk port with no native VLAN should not accept untagged traffic. Since both of the above configurations for the native VLAN should only be done if VLAN awareness is requested, they are actually done from the ocelot_port_vlan_filtering function, after the basic procedure of toggling the VLAN awareness flag of the port. But there's a problem with that simplistic approach: we are trying to juggle with 2 independent variables from a single function: - Native VLAN of the port - its value is held in port->vid. - VLAN awareness state of the port - currently there are some issues here, more on that later*. The actual problem can be seen when enslaving the switch ports to a VLAN filtering bridge: 0. The driver configures a pvid of zero for each port, when in standalone mode. While the bridge configures a default_pvid of 1 for each port that gets added as a slave to it. 1. The bridge calls ocelot_port_vlan_filtering with vlan_aware=true. The VLAN-filtering-dependent portion of the native VLAN configuration is done, considering that the native VLAN is 0. 2. The bridge calls ocelot_vlan_add with vid=1, pvid=true, untagged=true. The native VLAN changes to 1 (change which gets propagated to hardware). 3. ??? - nobody calls ocelot_port_vlan_filtering again, to reapply the VLAN-filtering-dependent portion of the native VLAN configuration, for the new native VLAN of 1. One can notice that after toggling "ip link set dev br0 type bridge vlan_filtering 0 && ip link set dev br0 type bridge vlan_filtering 1", the new native VLAN finally makes it through and untagged traffic finally starts flowing again. But obviously that shouldn't be needed. So it is clear that 2 independent variables need to both re-trigger the native VLAN configuration. So we introduce the second variable as ocelot_port->vlan_aware. *Actually both the DSA Felix driver and the Ocelot driver already had each its own variable: - Ocelot: ocelot_port_private->vlan_aware - Felix: dsa_port->vlan_filtering but the common Ocelot library needs to work with a single, common, variable, so there is some refactoring done to move the vlan_aware property from the private structure into the common ocelot_port structure. Fixes: 97bb69e1 ("net: mscc: ocelot: break apart ocelot_vlan_port_apply") Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller authored
Daniel Borkmann says: ==================== pull-request: bpf 2020-04-15 The following pull-request contains BPF updates for your *net* tree. We've added 10 non-merge commits during the last 3 day(s) which contain a total of 11 files changed, 238 insertions(+), 95 deletions(-). The main changes are: 1) Fix offset overflow for BPF_MEM BPF_DW insn mapping on arm32 JIT, from Luke Nelson and Xi Wang. 2) Prevent mprotect() to make frozen & mmap()'ed BPF map writeable again, from Andrii Nakryiko and Jann Horn. 3) Fix type of old_fd in bpf_xdp_set_link_opts to int in libbpf and add selftests, from Toke Høiland-Jørgensen. 4) Fix AF_XDP to check that headroom cannot be larger than the available space in the chunk, from Magnus Karlsson. 5) Fix reset of XDP prog when expected_fd is set, from David Ahern. 6) Fix a segfault in bpftool's struct_ops command when BTF is not available, from Daniel T. Lee. ==================== Signed-off-by: -
David S. Miller authored
Merge tag 'mac80211-for-net-2020-04-15' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== A couple of fixes: * FTM responder policy netlink validation fix (but the only user validates again later) * kernel-doc fixes * a fix for a race in mac80211 radio registration vs. userspace * a mesh channel switch fix * a fix for a syzbot reported kasprintf() issue ==================== Signed-off-by:
-
Toke Høiland-Jørgensen authored
David Ahern noticed that there was a bug in the EXPECTED_FD code so programs did not get detached properly when that parameter was supplied. This case was not included in the xdp_attach tests; so let's add it to be sure that such a bug does not sneak back in down. Fixes: 87854a0b ("selftests/bpf: Add tests for attaching XDP programs") Reported-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Song Liu <songliubraving@fb.com> Link: https://lore.kernel.org/bpf/20200414145025.182163-2-toke@redhat.com
-
Toke Høiland-Jørgensen authored
The 'old_fd' parameter used for atomic replacement of XDP programs is supposed to be an FD, but was left as a u32 from an earlier iteration of the patch that added it. It was converted to an int when read, so things worked correctly even with negative values, but better change the definition to correctly reflect the intention. Fixes: bd5ca3ef ("libbpf: Add function to set link XDP fd while specifying old program") Reported-by:
-
Andrii Nakryiko authored
For some types of BPF programs that utilize expected_attach_type, libbpf won't set load_attr.expected_attach_type, even if expected_attach_type is known from section definition. This was done to preserve backwards compatibility with old kernels that didn't recognize expected_attach_type attribute yet (which was added in 5e43f899 ("bpf: Check attach type at prog load time"). But this is problematic for some BPF programs that utilize newer features that require kernel to know specific expected_attach_type (e.g., extended set of return codes for cgroup_skb/egress programs). This patch makes libbpf specify expected_attach_type by default, but also detect support for this field in kernel and not set it during program load. This allows to have a good metadata for bpf_program (e.g., bpf_program__get_extected_attach_type()), but still work with old kernels (for cases where it can work at all). Additionally, due to expected_attach_type being always set for recognized program types, bpf_program__attach_cgroup doesn't have to do extra checks to determine correct attach type, so remove that additional logic. Also adjust section_names selftest to account for this change. More detailed discussion can be found in [0]. [0] https://lore.kernel.org/bpf/20200412003604.GA15986@rdna-mbp.dhcp.thefacebook.com/ Fixes: 5cf1e914 ("bpf: cgroup inet skb programs can return 0 to 3") Fixes: 5e43f899 ("bpf: Check attach type at prog load time") Reported-by:
Andrey Ignatov <rdna@fb.com> Signed-off-by:
Andrii Nakryiko <andriin@fb.com> Signed-off-by:
-
Magnus Karlsson authored
Add a check that the headroom cannot be larger than the available space in the chunk. In the current code, a malicious user can set the headroom to a value larger than the chunk size minus the fixed XDP headroom. That way packets with a length larger than the supported size in the umem could get accepted and result in an out-of-bounds write. Fixes: c0c77d8f ("xsk: add user memory registration support sockopt") Reported-by:
Bui Quang Minh <minhquangbui99@gmail.com> Signed-off-by:
Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by:
-
Tamizh chelvam authored
Previously mesh channel switch happens if beacon contains CSA IE without checking the mesh peer info. Due to that channel switch happens even if the beacon is not from its own mesh peer. Fixing that by checking if the CSA originated from the same mesh network before proceeding for channel switch. Signed-off-by:
Tamizh chelvam <tamizhr@codeaurora.org> Link: https://lore.kernel.org/r/1585403604-29274-1-git-send-email-tamizhr@codeaurora.orgSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Sumit Garg authored
A race condition leading to a kernel crash is observed during invocation of ieee80211_register_hw() on a dragonboard410c device having wcn36xx driver built as a loadable module along with a wifi manager in user-space waiting for a wifi device (wlanX) to be active. Sequence diagram for a particular kernel crash scenario: user-space ieee80211_register_hw() ieee80211_tasklet_handler() ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ | | | |<---phy0----wiphy_register() | |-----iwd if_add---->| | | |<---IRQ----(RX packet) | Kernel crash | | due to unallocated | | workqueue. | | | | | alloc_ordered_workqueue() | | | | | Misc wiphy init. | | | | | ieee80211_if_add() | | | | As evident from above sequence diagram, this race condition isn't specific to a particular wifi driver but rather the initialization sequence in ieee80211_register_hw() needs to be fixed. So re-order the initialization sequence and the updated sequence diagram would look like: user-space ieee80211_register_hw() ieee80211_tasklet_handler() ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ | | | | alloc_ordered_workqueue() | | | | | Misc wiphy init. | | | | |<---phy0----wiphy_register() | |-----iwd if_add---->| | | |<---IRQ----(RX packet) | | | | ieee80211_if_add() | | | | Cc: stable@vger.kernel.org Signed-off-by:Sumit Garg <sumit.garg@linaro.org> Link: https://lore.kernel.org/r/1586254255-28713-1-git-send-email-sumit.garg@linaro.org [Johannes: fix rtnl imbalances] Signed-off-by:
-
- 14 Apr, 2020 24 commits
-
-
David S. Miller authored
Russell King says: ==================== Fix 88x3310 leaving power save mode This series fixes a problem with the 88x3310 PHY on Macchiatobin coming out of powersave mode noticed by Matteo Croce. It seems that certain PHY firmwares do not properly exit powersave mode, resulting in a fibre link not coming up. The solution appears to be to soft-reset the PHY after clearing the powersave bit. We add support for reporting the PHY firmware version to the kernel log, and use it to trigger this new behaviour if we have v0.3.x.x or more recent firmware on the PHY. This, however, is a guess as the firmware revision documentation does not mention this issue, and we know that v0.2.1.0 works without this fix but v0.3.3.0 and later does not. ==================== Signed-off-by: -
Russell King authored
Soft-reset the PHY when coming out of low power mode, which seems to be necessary with firmware versions 0.3.3.0 and 0.3.10.0. This depends on ("net: marvell10g: report firmware version") Fixes: c9cc1c81 ("net: phy: marvell10g: place in powersave mode at probe") Reported-by:Matteo Croce <mcroce@redhat.com> Tested-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
-
Russell King authored
Report the firmware version when probing the PHY to allow issues attributable to firmware to be diagnosed. Tested-by:
-
Jason Gunthorpe authored
Positive return values are also failures that don't set val, although this probably can't happen. Fixes gcc 10 warning: drivers/net/ethernet/chelsio/cxgb4/t4_hw.c: In function ‘t4_phy_fw_ver’: drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:3747:14: warning: ‘val’ may be used uninitialized in this function [-Wmaybe-uninitialized] 3747 | *phy_fw_ver = val; Fixes: 01b69614 ("cxgb4: Add PHY firmware support for T420-BT cards") Signed-off-by:
-
Atsushi Nemoto authored
Allow all the RGMII modes to be used. (Not only "rgmii", "rgmii-id" but "rgmii-txid", "rgmii-rxid") Signed-off-by:
Atsushi Nemoto <atsushi.nemoto@sord.co.jp> Signed-off-by:
-
David S. Miller authored
Andrew Lunn says: ==================== mv88e6xxx fixed link fixes Recent changes for how the MAC is configured broke fixed links, as used by CPU/DSA ports, and for SFPs when phylink cannot be used. The first fix is unchanged from v1. The second fix takes a different solution than v1. If a CPU or DSA port is known to have a PHYLINK instance, configure the port down before instantiating the PHYLINK, so it is in the down state as expected by PHYLINK. ==================== Signed-off-by: -
Andrew Lunn authored
DSA and CPU ports can be configured in two ways. By default, the driver should configure such ports to there maximum bandwidth. For most use cases, this is sufficient. When this default is insufficient, a phylink instance can be bound to such ports, and phylink will configure the port, e.g. based on fixed-link properties. phylink assumes the port is initially down. Given that the driver should have already configured it to its maximum speed, ask the driver to down the port before instantiating the phylink instance. Fixes: 30c4a5b0 ("net: mv88e6xxx: use resolved link config in mac_link_up()") Signed-off-by:
-
Andrew Lunn authored
The 88e6185 is reporting it has detected a PHY, when a port is connected to an SFP. As a result, the fixed-phy configuration is not being applied. That then breaks packet transfer, since the port is reported as being down. Add additional conditions to check the interface mode, and if it is fixed always configure the port on link up/down, independent of the PPU status. Fixes: 30c4a5b0 ("net: mv88e6xxx: use resolved link config in mac_link_up()") Signed-off-by:
-
David S. Miller authored
Shannon Nelson says: ==================== ionic: address automated build complaints Kernel build checks found a couple of things to improve. ==================== Signed-off-by: -
Shannon Nelson authored
Remove an unused initialized value. Fixes: 7e4d4759 ("ionic: replay filters after fw upgrade") Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Shannon Nelson <snelson@pensando.io> Signed-off-by:
-
Shannon Nelson authored
Add the appropriate header for using dynamic_hex_dump(), which seems to be incidentally included in some configurations but not all. Fixes: 7e4d4759 ("ionic: replay filters after fw upgrade") Reported-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
-
David Howells authored
Fix the DATA packet transmission to disable nofrag for UDPv4 on an AF_INET6 socket as well as UDPv6 when trying to transmit fragmentably. Without this, packets filled to the normal size used by the kernel AFS client of 1412 bytes be rejected by udp_sendmsg() with EMSGSIZE immediately. The ->sk_error_report() notification hook is called, but rxrpc doesn't generate a trace for it. This is a temporary fix; a more permanent solution needs to involve changing the size of the packets being filled in accordance with the MTU, which isn't currently done in AF_RXRPC. The reason for not doing so was that, barring the last packet in an rx jumbo packet, jumbos can only be assembled out of 1412-byte packets - and the plan was to construct jumbos on the fly at transmission time. Also, there's no point turning on IPV6_MTU_DISCOVER, since IPv6 has to engage in this anyway since fragmentation is only done by the sender. We can then condense the switch-statement in rxrpc_send_data_packet(). Fixes: 75b54cb5 ("rxrpc: Add IPv6 support") Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Atsushi Nemoto authored
KSZ9131 will not work with some switches due to workaround for KSZ9031 introduced in commit d2fd719b ("net/phy: micrel: Add workaround for bad autoneg"). Use genphy_read_status instead of dedicated ksz9031_read_status. Fixes: bff5b4b3 ("net: phy: micrel: add Microchip KSZ9131 initial driver") Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-2020-04-14' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for v5.7 First set of fixes for v5.6. Fixes for a crash and for two compiler warnings. brcmfmac * fix a crash related to monitor interface ath11k * fix compiler warnings without CONFIG_THERMAL rtw88 * fix compiler warnings related to suspend and resume functions ==================== Signed-off-by:
-
Zou Wei authored
This issue was detected by using the Coccinelle software: kernel/bpf/verifier.c:1259:16-21: WARNING: conversion to bool not needed here The conversion to bool is unneeded, remove it. Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Zou Wei <zou_wei@huawei.com> Signed-off-by:
-
David Ahern authored
The commit mentioned in the Fixes tag reuses the local prog variable when looking up an expected_fd. The variable is not reset when fd < 0 causing a detach with the expected_fd set to actually call dev_xdp_install for the existing program. The end result is that the detach does not happen. Fixes: 92234c8f ("xdp: Support specifying expected existing program when attaching XDP") Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Reviewed-by:
-
Daniel T. Lee authored
In commit 65c93628 ("bpftool: Add struct_ops support") a new type of command named struct_ops has been added. This command requires a kernel with CONFIG_DEBUG_INFO_BTF=y set and for retrieving BTF info in bpftool, the helper get_btf_vmlinux() is used. When running this command on kernel without BTF debug info, this will lead to 'btf_vmlinux' variable being an invalid(error) pointer. And by this, btf_free() causes a segfault when executing 'bpftool struct_ops'. This commit adds pointer validation with IS_ERR not to free invalid pointer, and this will fix the segfault issue. Fixes: 65c93628 ("bpftool: Add struct_ops support") Signed-off-by:
Daniel T. Lee <danieltimlee@gmail.com> Signed-off-by:
Martin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/20200410020612.2930667-1-danieltimlee@gmail.com
-
Andrii Nakryiko authored
Test that frozen and mmap()'ed BPF map can't be mprotect()'ed as writable or executable memory. Also validate that "downgrading" from writable to read-only doesn't screw up internal writable count accounting for the purposes of map freezing. Signed-off-by:
-
Andrii Nakryiko authored
VM_MAYWRITE flag during initial memory mapping determines if already mmap()'ed pages can be later remapped as writable ones through mprotect() call. To prevent user application to rewrite contents of memory-mapped as read-only and subsequently frozen BPF map, remove VM_MAYWRITE flag completely on initially read-only mapping. Alternatively, we could treat any memory-mapping on unfrozen map as writable and bump writecnt instead. But there is little legitimate reason to map BPF map as read-only and then re-mmap() it as writable through mprotect(), instead of just mmap()'ing it as read/write from the very beginning. Also, at the suggestion of Jann Horn, drop unnecessary refcounting in mmap operations. We can just rely on VMA holding reference to BPF map's file properly. Fixes: fc970227 ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY") Reported-by:
Jann Horn <jannh@google.com> Signed-off-by:
-
Luke Nelson authored
This patch fixes an incorrect check in how immediate memory offsets are computed for BPF_DW on arm. For BPF_LDX/ST/STX + BPF_DW, the 32-bit arm JIT breaks down an 8-byte access into two separate 4-byte accesses using off+0 and off+4. If off fits in imm12, the JIT emits a ldr/str instruction with the immediate and avoids the use of a temporary register. While the current check off <= 0xfff ensures that the first immediate off+0 doesn't overflow imm12, it's not sufficient for the second immediate off+4, which may cause the second access of BPF_DW to read/write the wrong address. This patch fixes the problem by changing the check to off <= 0xfff - 4 for BPF_DW, ensuring off+4 will never overflow. A side effect of simplifying the check is that it now allows using negative immediate offsets in ldr/str. This means that small negative offsets can also avoid the use of a temporary register. This patch introduces no new failures in test_verifier or test_bpf.c. Fixes: c5eae692 ("ARM: net: bpf: improve 64-bit store implementation") Fixes: ec19e02b ("ARM: net: bpf: fix LDX instructions") Co-developed-by:
Xi Wang <xi.wang@gmail.com> Signed-off-by:
Luke Nelson <luke.r.nels@gmail.com> Signed-off-by:
-
Arnd Bergmann authored
The rtw88 driver defines emtpy functions with multiple indirections but gets one of these wrong: drivers/net/wireless/realtek/rtw88/pci.c:1347:12: error: 'rtw_pci_resume' defined but not used [-Werror=unused-function] 1347 | static int rtw_pci_resume(struct device *dev) | ^~~~~~~~~~~~~~ drivers/net/wireless/realtek/rtw88/pci.c:1342:12: error: 'rtw_pci_suspend' defined but not used [-Werror=unused-function] 1342 | static int rtw_pci_suspend(struct device *dev) Better simplify it to rely on the conditional reference in SIMPLE_DEV_PM_OPS(), and mark the functions as __maybe_unused to avoid warning about it. I'm not sure if these are needed at all given that the functions don't do anything, but they were only recently added. Fixes: 44bc17f7 ("rtw88: support wowlan feature for 8822c") Signed-off-by:Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200408185413.218643-1-arnd@arndb.de
-
Lothar Rubusch authored
Update missing kernel-doc annotations and fix of related warnings at 'make htmldocs'. Signed-off-by:
Lothar Rubusch <l.rubusch@gmail.com> Link: https://lore.kernel.org/r/20200408231013.28370-1-l.rubusch@gmail.com [fix indentation, attribute references] Signed-off-by:
-
Tuomas Tynkkynen authored
syzbot reports a warning: precision 33020 too large WARNING: CPU: 0 PID: 9618 at lib/vsprintf.c:2471 set_precision+0x150/0x180 lib/vsprintf.c:2471 vsnprintf+0xa7b/0x19a0 lib/vsprintf.c:2547 kvasprintf+0xb2/0x170 lib/kasprintf.c:22 kasprintf+0xbb/0xf0 lib/kasprintf.c:59 hwsim_del_radio_nl+0x63a/0x7e0 drivers/net/wireless/mac80211_hwsim.c:3625 genl_family_rcv_msg_doit net/netlink/genetlink.c:672 [inline] ... entry_SYSCALL_64_after_hwframe+0x49/0xbe Thus it seems that kasprintf() with "%.*s" format can not be used for duplicating a string with arbitrary length. Replace it with kstrndup(). Note that later this string is limited to NL80211_WIPHY_NAME_MAXLEN == 64, but the code is simpler this way. Reported-by: syzbot+6693adf1698864d21734@syzkaller.appspotmail.com Reported-by: syzbot+a4aee3f42d7584d76761@syzkaller.appspotmail.com Cc: stable@kernel.org Signed-off-by:
Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi> Link: https://lore.kernel.org/r/20200410123257.14559-1-tuomas.tynkkynen@iki.fi [johannes: add note about length limit] Signed-off-by:
-
Johannes Berg authored
The nested policy here should be established using the NLA_POLICY_NESTED() macro so the length is properly filled in. Cc: stable@vger.kernel.org Fixes: 81e54d08 ("cfg80211: support FTM responder configuration/statistics") Link: https://lore.kernel.org/r/20200412004029.9d0722bb56c8.Ie690bfcc4a1a61ff8d8ca7e475d59fcaa52fb2da@changeidSigned-off-by:
-
- 13 Apr, 2020 3 commits
-
-
Christophe JAILLET authored
s/mvmeta/mvneta/ Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Florian Westphal authored
mptcp_connect/28740 is trying to release lock (sk_lock-AF_INET) at: [<ffffffff82c15869>] mptcp_poll+0xb9/0x550 but there are no more locks to release! Call Trace: lock_release+0x50f/0x750 release_sock+0x171/0x1b0 mptcp_poll+0xb9/0x550 sock_poll+0x157/0x470 ? get_net_ns+0xb0/0xb0 do_sys_poll+0x63c/0xdd0 Problem is that __mptcp_tcp_fallback() releases the mptcp socket lock, but after recent change it doesn't do this in all of its return paths. To fix this, remove the unlock from __mptcp_tcp_fallback() and always do the unlock in the caller. Also add a small comment as to why we have this __mptcp_needs_tcp_fallback(). Fixes: 0b4f33de ("mptcp: fix tcp fallback crash") Reported-by: syzbot+e56606435b7bfeea8cf5@syzkaller.appspotmail.com Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
-
Gilberto Bertin authored
This allows netif_receive_generic_xdp() to correctly determine the RX queue from which the skb is coming, so that the context passed to the XDP program will contain the correct RX queue index. Signed-off-by:
Gilberto Bertin <me@jibi.io> Signed-off-by:
-
- 12 Apr, 2020 1 commit
-
-
Christophe JAILLET authored
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'. Fixes: 93a76530 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Signed-off-by:
-
