Beacon data wasn't properly cleared during early
phase of recovery. This in turn caused firmware to
crash because the beacon data was submitted before
vdevs were fully re-configured. Ultimately the
device was considered wedged and nothing worked
until driver was reloaded.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

If DMA mapping of next beacon failed ath10k leaked
the beacon.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

If DMA mapping of next beacon failed it was
possible for next SWBA to access a pointer that
was already unmapped and freed. This could cause
memory corruption.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

If for some reason mac80211 wouldn't stop
beaconing gracefully and just removed interface of
a running AP/IBSS interface it was possible to
leak pending beacon DMA mapping. It's very
unlikely but better safe than sorry.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It doesn't make much sense to even try suspending
the device when recovering. Recovering means the
device is unresponsive and waiting for suspend
procedure means taking a 3 second timeout waiting
for tx credits.

This speeds up firmware recovery significantly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

When warm resetting it's possible for device to
crash during initialization. Instead of waiting 3
seconds just return failure as soon as
FW_IND_EVENT_PENDING is set.

This speeds up device bootup and recovery in some
cases.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This just makes it easier to tell apart different
kinds of bringup failure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is the first step to remove leftover code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some ancient Broadcom devices had one core per band, e.g.:
ssb: Found chip with id 0x4306, rev 0x02 and package 0x00
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x02, vendor 0x4243)
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x04, vendor 0x4243)
ssb: Core 2 found: PCMCIA (cc 0x80D, rev 0x01, vendor 0x4243)
ssb: Core 3 found: V90 (cc 0x807, rev 0x01, vendor 0x4243)
ssb: Core 4 found: PCI (cc 0x804, rev 0x07, vendor 0x4243)
ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x04, vendor 0x4243)

This hardware model was dropped for newer devices handled by b43.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We've implemented table calculation, but forgot to enable writing it in
power setup function.
By the way document table layout.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Logic in specs and our code was wrong. Init and calibration values for
newer cards depend on radio revision, not PHY revision.
To make code clearer, change tables names to include "radio" or "phy".
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

They were extracted from MMIO dumps of 14e4:4353 and wl 6.30.223.141.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Mostly just add place for future code
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bit 0x200 has been noticed in the following log:
 radio_read(0x02ca) -> 0x0000
radio_write(0x00ca) <- 0x0080
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

New Broadcom drivers don't upload it anymore. It was probably a copy & paste
mistake in early N-PHY rev 3+ days.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently AMSDU and AMPDU aggregation is enabled for TID 0 to
TID 5 streams. Lets enable it for remaining two streams also.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This will help to aggregate more packets which yields better
throughput results for 11ac chipsets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This will help to aggregate more packets which yields better
throughput results.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Firmware dump feature is added for PCIe based chipsets.
Separate file will be created at /var/log/fw_dump_*
for each memory segment.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This option be useful to dump firmware memory for debugging
purpose. Actual code to dump firmware momory for SDIO and PCIe
chipsets will be added later.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After changing local per interface beacon setting restore original
global beaconing state.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When command timeout occurs due to a firmware/hardware bug,
there is no chance of next command being successful. We will
keep cmd_sent flag on so that next command won't be sent to
firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

IE's are parsed from beacon buffer and stored locally using
mwifiex_update_bss_desc_with_ie() function.
Sometimes the local pointers point to the data inside IE, but
while using them it is assumed that they are pointing to the IE
itself.

These issues are fixed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

'add_remove_card_sem' semaphore already takes care of
synchronization for driver load and unload threads.
Hence there won't be a case when unload thread is waiting on
'wait_for_completion(fw_load)'.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This option allows driver to finish pending operations in
disconnect handler by not killing URBs after usb_deregister
call.

We will get rid of global pointer 'usb_card' by moving code
from cleanup_module() to disconnect(). This will help to match
with our handling for SDIO and PCIe interfaces.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

New skbs are allocated at the time of AMSDU aggregation. Setting
up in timestamps for such skbs was missing which would result
into wrong queue delays passed to FW. Fix this by setting
timestamp of skbs created for AMSDU aggregation.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Command nodes are increased from 20 to 50. Now we can always
scan 1 channel per scan command to avoid traffic delay/loss in
connected state. We will get rid of *CHANNEL_PER_SCAN_CMD macros
used due to command node constraints.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For PCIe, aggregate more AMSDU packets till PCIe TXBD is full.

For SDIO, aggregation was disabled for AMSDU packets because
AMSDU aggregated packet size is already 4K or 8K, SDIO Multiport
Aggregation feature didn't use to gain much previously.
Now with increased multiport aggregation buffer, we can enable
it for AMSDU packets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently Tx and Rx buffer sizes are 8K and 16K respectively for
all chipsets. We will change them to 32K for SD8897 and 16K for
older chipsets. SD8897 chipset has more SDIO data ports than
older chipsets.
This patch will help to improve throughput numbers.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

WARNING: single byte memset is suspicious.
         Swapped 2nd/3rd argument?

This code happens to work because rx_mcs is the first variable
in mcs structure. We should use 'mcs.rx_mcs' here anyway.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When using scatter-gather, more descriptor entries get used.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Sometimes, due to the race between Rx path and WMI_BA_STATUS_EVENTID WMI event,
few frames may be passed to the stack before reorder buffer allocated.
Then, after BACK establishment, it start getting frames with sequence number ahead of
SSN, and it get interpreted as missing frames. Then, BACK mechanism will wait
for missing frames; data traffic will be stopped. In case of interface configured
for DHCP, this data delay causes DHCP failure.

Relax checking for sequence number; use sequence of 1-st frame handled by the buffer
as SSN for this buffer.

This is work-around, real fix should be done when proper BACK mechanism implemented.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

- add pcp_max_assoc_sta to the struct wmi_pcp_start_cmd
- enum for the scan ststus
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reshuffle prints to consolidate firmware/hardware information
report upon card init

Convert print for unhandled MISC ISR bits to "debug" - it is
normal situation and not an "error"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use generic TSF timers to trigger powersave state changes based
information from the P2P NoA attribute.
Opportunistic Powersave is not handled, because the driver does not
support powersave at the moment.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Preparation for adding P2P powersave and multi-channel support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>