- 19 Dec, 2018 1 commit
-
-
Anssi Hannula authored
64-bit DMA addresses are split in upper and lower halves that are written in separate fields on GEM. For RX, bit 0 of the address is used as the ownership bit (RX_USED). When the RX_USED bit is unset the controller is allowed to write data to the buffer. The driver does not guarantee that the controller already sees the upper half when the RX_USED bit is cleared, possibly resulting in the controller writing an incoming frame to an address with an incorrect upper half and therefore possibly corrupting unrelated system memory. Fix that by adding the necessary DMA memory barrier between the writes. This corruption was observed on a ZynqMP based system. Fixes: fff8019a ("net: macb: Add 64 bit addressing support for GEM") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Acked-by: Harini Katakam <harini.katakam@xilinx.com> Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 18 Dec, 2018 16 commits
-
-
Davide Caratti authored
Herton reports the following error when building a userspace program that includes net_stamp.h: In file included from foo.c:2: /usr/include/linux/net_tstamp.h:158:2: error: unknown type name ‘clockid_t’ clockid_t clockid; /* reference clockid */ ^~~~~~~~~ Fix it by using __kernel_clockid_t in place of clockid_t. Fixes: 80b14dee ("net: Add a new socket option for a future transmit time.") Cc: Timothy Redaelli <tredaelli@redhat.com> Reported-by: Herton R. Krzesinski <herton@redhat.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Tested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Claudiu Beznea authored
On some platforms (currently detected only on SAMA5D4) TX might stuck even the pachets are still present in DMA memories and TX start was issued for them. This happens due to race condition between MACB driver updating next TX buffer descriptor to be used and IP reading the same descriptor. In such a case, the "TX USED BIT READ" interrupt is asserted. GEM/MACB user guide specifies that if a "TX USED BIT READ" interrupt is asserted TX must be restarted. Restart TX if used bit is read and packets are present in software TX queue. Packets are removed from software TX queue if TX was successful for them (see macb_tx_interrupt()). Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dan Carpenter authored
The function should return an error if create_singlethread_workqueue() fails. Fixes: 34877a15 ("net: stmmac: Rework and fix TX Timeout code") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Cong Wang authored
Similar to commit 143ece65 ("tipc: check tsk->group in tipc_wait_for_cond()") we have to reload grp->dests too after we re-take the sock lock. This means we need to move the dsts check after tipc_wait_for_cond() too. Fixes: 75da2163 ("tipc: introduce communication groups") Reported-and-tested-by: syzbot+99f20222fc5018d2b97a@syzkaller.appspotmail.com Cc: Ying Xue <ying.xue@windriver.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dan Carpenter authored
We accidentally deleted the code to set "rc = -ENOMEM;" and this patch adds it back. Fixes: d2201a21 ("qed: No need for LL2 frags indication") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Antoine Tenart authored
The mvpp2_phylink_validate() function sets all modes that are supported by a given PPv2 port. A recent change made all ports to advertise they support 10G modes in certain cases. This is not true, as only the port #0 can do so. This patch fixes it. Fixes: 01b3fd5a ("net: mvpp2: fix detection of 10G SFP modules") Cc: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jorgen Hansen authored
If a server side socket is bound to an address, but not in the listening state yet, incoming connection requests should receive a reset control packet in response. However, the function used to send the reset silently drops the reset packet if the sending socket isn't bound to a remote address (as is the case for a bound socket not yet in the listening state). This change fixes this by using the src of the incoming packet as destination for the reset packet in this case. Fixes: d021c344 ("VSOCK: Introduce VM Sockets") Reviewed-by: Adit Ranadive <aditr@vmware.com> Reviewed-by: Vishnu Dasa <vdasa@vmware.com> Signed-off-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsecDavid S. Miller authored
Steffen Klassert says: ==================== pull request (net): ipsec 2018-12-18 1) Fix error return code in xfrm_output_one() when no dst_entry is attached to the skb. From Wei Yongjun. 2) The xfrm state hash bucket count reported to userspace is off by one. Fix from Benjamin Poirier. 3) Fix NULL pointer dereference in xfrm_input when skb_dst_force clears the dst_entry. 4) Fix freeing of xfrm states on acquire. We use a dedicated slab cache for the xfrm states now, so free it properly with kmem_cache_free. From Mathias Krause. Please pull or let me know if there are problems. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Ido Schimmel says: ==================== mlxsw: VXLAN and firmware flashing fixes Patch #1 fixes firmware flashing failures by increasing the time period after which the driver fails the transaction with the firmware. The problem is explained in detail in the commit message. Patch #2 adds a missing trap for decapsulated ARP packets. It is necessary for VXLAN routing to work. Patch #3 fixes a memory leak during driver reload caused by NULLing a pointer before kfree(). Please consider patch #1 for 4.19.y ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
The pointer was NULLed before freeing the memory, resulting in a memory leak. Trace from kmemleak: unreferenced object 0xffff88820ae36528 (size 512): comm "devlink", pid 5374, jiffies 4295354033 (age 10829.296s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000a43f5195>] kmem_cache_alloc_trace+0x1be/0x330 [<00000000312f8140>] mlxsw_sp_nve_init+0xcb/0x1ae0 [<0000000009201d22>] mlxsw_sp_init+0x1382/0x2690 [<000000007227d877>] mlxsw_sp1_init+0x1b5/0x260 [<000000004a16feec>] __mlxsw_core_bus_device_register+0x776/0x1360 [<0000000070ab954c>] mlxsw_devlink_core_bus_device_reload+0x129/0x220 [<00000000432313d5>] devlink_nl_cmd_reload+0x119/0x1e0 [<000000003821a06b>] genl_family_rcv_msg+0x813/0x1150 [<00000000d54d04c0>] genl_rcv_msg+0xd1/0x180 [<0000000040543d12>] netlink_rcv_skb+0x152/0x3c0 [<00000000efc4eae8>] genl_rcv+0x2d/0x40 [<00000000ea645603>] netlink_unicast+0x52f/0x740 [<00000000641fca1a>] netlink_sendmsg+0x9c7/0xf50 [<00000000fed4a4b8>] sock_sendmsg+0xbe/0x120 [<00000000d85795a9>] __sys_sendto+0x397/0x620 [<00000000c5f84622>] __x64_sys_sendto+0xe6/0x1a0 Fixes: 6e6030bd ("mlxsw: spectrum_nve: Implement common NVE core") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
After a packet was decapsulated it is classified to the relevant FID based on its VNI and undergoes L2 forwarding. Unlike regular (non-encapsulated) ARP packets, Spectrum does not trap decapsulated ARP packets during L2 forwarding and instead can only trap such packets in the underlay router during decapsulation. Add this missing packet trap, which is required for VXLAN routing when the MAC of the target host is not known. Fixes: b02597d5 ("mlxsw: spectrum: Add NVE packet traps") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Shalom Toledo authored
During the firmware flash process, some of the EMADs get timed out, which causes the driver to send them again with a limit of 5 retries. There are some situations in which 5 retries is not enough and the EMAD access fails. If the failed EMAD was related to the flashing process, the driver fails the flashing. The reason for these timeouts during firmware flashing is cache misses in the CPU running the firmware. In case the CPU needs to fetch instructions from the flash when a firmware is flashed, it needs to wait for the flashing to complete. Since flashing takes time, it is possible for pending EMADs to timeout. Fix by increasing EMADs' timeout while flashing firmware. Fixes: ce6ef68f ("mlxsw: spectrum: Implement the ethtool flash_device callback") Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
Currently the ethtool_regs version is set to 0 for all DSA drivers. Use this field to store the chip ID to simplify the pretty dump of any interfaces registered by the "dsa" driver. Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Willem de Bruijn says: ==================== net: SO_TIMESTAMPING fixes Fix two omissions: - tx timestamping is missing for AF_INET6/SOCK_RAW/IPPROTO_RAW - SOF_TIMESTAMPING_OPT_ID is missing for IPPROTO_RAW, PF_PACKET, CAN Discovered while expanding the selftest in tools/testing/selftests/networking/timestamping/txtimestamp.c Will send the test patchset to net-next once the fixes make it to that branch. For now, it is available at https://github.com/wdebruij/linux/commits/txtimestamp-test-1 ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Willem de Bruijn authored
SOF_TIMESTAMPING_OPT_ID is supported on TCP, UDP and RAW sockets. But it was missing on RAW with IPPROTO_IP, PF_PACKET and CAN. Add skb_setup_tx_timestamp that configures both tx_flags and tskey for these paths that do not need corking or use bytestream keys. Fixes: 09c2d251 ("net-timestamp: add key to disambiguate concurrent datagrams") Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Willem de Bruijn authored
Raw sockets support tx timestamping, but one case is missing. IPPROTO_RAW takes a separate packet construction path. raw_send_hdrinc has an explicit call to sock_tx_timestamp, but rawv6_send_hdrinc does not. Add it. Fixes: 11878b40 ("net-timestamp: SOCK_RAW and PING timestamping") Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 17 Dec, 2018 1 commit
-
-
Vivien Didelot authored
Make my Gmail address the primary one from now on. Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 16 Dec, 2018 12 commits
-
-
Marcin Wojtas authored
Recent changes in the mvneta driver reworked allocation and handling of the ingress buffers to use entire pages. Apart from that in SW BM scenario the HW must be informed via PRXDQS about the biggest possible incoming buffer that can be propagated by RX descriptors. The BufferSize field was filled according to the MTU-dependent pkt_size value. Later change to PAGE_SIZE broke RX operation when usin 64K pages, as the field is simply too small. This patch conditionally limits the value passed to the BufferSize of the PRXDQS register, depending on the PAGE_SIZE used. On the occasion remove now unused frag_size field of the mvneta_port structure. Fixes: 562e2f46 ("net: mvneta: Improve the buffer allocation method for SWBM") Signed-off-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Peng Li says: ==================== net: hns: Code improvements & fixes for HNS driver This patchset introduces some code improvements and fixes for the identified problems in the HNS driver. Every patch is independent. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yonglong Liu authored
Create a net bridge, add eth and vnet to the bridge. The vnet is used by a virtual machine. When ping the virtual machine from the outside host and the virtual machine send multicast at the same time, the ping package will lost. The multicast package send to the eth, eth will send it to the bridge too, and the bridge learn the mac of eth. When outside host ping the virtual mechine, it will match the promisc entry of the eth which is not expected, and the bridge send it to eth not to vnet, cause ping lost. So this patch change promisc tcam entry position to the END of 512 tcam entries, which indicate lower priority. And separate one promisc entry to two: mc & uc, to avoid package match the wrong tcam entry. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yonglong Liu authored
In some case, when mac enable|disable and adjust link, may cause hard to link(or abnormal) between mac and phy. This patch adds the code for rx PCS to avoid this bug. Disable the rx PCS when driver disable the gmac, and enable the rx PCS when driver enable the mac. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yonglong Liu authored
The ntuple-filters features is forced on by chip. But it shows "ntuple-filters: off [fixed]" when use ethtool. This patch make it correct with "ntuple-filters: on [fixed]". Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yonglong Liu authored
There will be a large number of MAC pause frames on the net, which caused tx timeout of net device. And then the net device was reset to try to recover it. So that is not useful, and will cause some other problems. So need doubled ndev->watchdog_timeo if device watchdog occurred until watchdog_timeo up to 40s and then try resetting to recover it. When collecting dfx information such as hardware registers when tx timeout. Some registers for count were cleared when read. So need move this task before update net state which also read the count registers. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yonglong Liu authored
1.In "hns_nic_init_irq", if request irq fail at index i, the function return directly without releasing irq resources that already requested. 2.In "hns_nic_net_up" after "hns_nic_init_irq", if exceptional branch occurs, irqs that already requested are not release. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yonglong Liu authored
If there are packets in hardware when changing the speed or duplex, it may cause hardware hang up. This patch adds the code to wait rx fbd clean up when ae stopped. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yonglong Liu authored
After resetting dsaf to try to repair chip error such as ecc error, the net device will be open if net interface is up. But at this time if there is the users set the net device up with the command ifconfig, the net device will be opened twice consecutively. Function napi_enable was called when open device. And Kernel panic will be occurred if it was called twice consecutively. Such as follow: static inline void napi_enable(struct napi_struct *n) { BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state)); smp_mb__before_clear_bit(); clear_bit(NAPI_STATE_SCHED, &n->state); } [37255.571996] Kernel panic - not syncing: BUG! [37255.595234] Call trace: [37255.597694] [<ffff80000008ab48>] dump_backtrace+0x0/0x1a0 [37255.603114] [<ffff80000008ad08>] show_stack+0x20/0x28 [37255.608187] [<ffff8000009c4944>] dump_stack+0x98/0xb8 [37255.613258] [<ffff8000009c149c>] panic+0x10c/0x26c [37255.618070] [<ffff80000070f134>] hns_nic_net_up+0x30c/0x4e0 [37255.623664] [<ffff80000070f39c>] hns_nic_net_open+0x94/0x12c [37255.629346] [<ffff80000084be78>] __dev_open+0xf4/0x168 [37255.634504] [<ffff80000084c1ac>] __dev_change_flags+0x98/0x15c [37255.640359] [<ffff80000084c29c>] dev_change_flags+0x2c/0x68 [37255.769580] [<ffff8000008dc400>] devinet_ioctl+0x650/0x704 [37255.775086] [<ffff8000008ddc38>] inet_ioctl+0x98/0xb4 [37255.780159] [<ffff800000827b7c>] sock_do_ioctl+0x44/0x84 [37255.785490] [<ffff800000828e04>] sock_ioctl+0x248/0x30c [37255.790737] [<ffff80000026dc6c>] do_vfs_ioctl+0x480/0x618 [37255.796156] [<ffff80000026de94>] SyS_ioctl+0x90/0xa4 [37255.801139] SMP: stopping secondary CPUs [37255.805079] kbox: catch panic event. [37255.809586] collected_len = 128928, LOG_BUF_LEN_LOCAL = 131072 [37255.816103] flush cache 0xffff80003f000000 size 0x800000 [37255.822192] flush cache 0xffff80003f000000 size 0x800000 [37255.828289] flush cache 0xffff80003f000000 size 0x800000 [37255.834378] kbox: no notify die func register. no need to notify [37255.840413] ---[ end Kernel panic - not syncing: BUG! This patchset fix this bug according to the flag NIC_STATE_DOWN. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yonglong Liu authored
According to the hip06 datasheet: 1.Six registers use wrong address: RCB_COM_SF_CFG_INTMASK_RING RCB_COM_SF_CFG_RING_STS RCB_COM_SF_CFG_RING RCB_COM_SF_CFG_INTMASK_BD RCB_COM_SF_CFG_BD_RINT_STS DSAF_INODE_VC1_IN_PKT_NUM_0_REG 2.The offset of DSAF_INODE_VC1_IN_PKT_NUM_0_REG should be 0x103C + 0x80 * all_chn_num 3.The offset to show the value of DSAF_INODE_IN_DATA_STP_DISC_0_REG is wrong, so the value of DSAF_INODE_SW_VLAN_TAG_DISC_0_REG will be overwrite These registers are only used in "ethtool -d", so that did not cause ndev to misfunction. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yonglong Liu authored
There are two test cases: 1. Remove the 4 modules:hns_enet_drv/hns_dsaf/hnae/hns_mdio, and install them again, must use "ifconfig down/ifconfig up" command pair to bring port to work. This patch calls phy_stop function when init phy to fix this bug. 2. Remove the 2 modules:hns_enet_drv/hns_dsaf, and install them again, all ports can not use anymore, because of the phy devices register failed(phy devices already exists). Phy devices are registered when hns_dsaf installed, this patch removes them when hns_dsaf removed. The two cases are sometimes related, fixing the second case also requires fixing the first case, so fix them together. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yonglong Liu authored
According to the hip06 Datasheet: 1. The offset of INGRESS_SW_VLAN_TAG_DISC should be 0x1A00+4*all_chn_num 2. The offset of INGRESS_IN_DATA_STP_DISC should be 0x1A50+4*all_chn_num Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 15 Dec, 2018 6 commits
-
-
Eric Dumazet authored
Sergey reported that forwarding was no longer working if fq packet scheduler was used. This is caused by the recent switch to EDT model, since incoming packets might have been timestamped by __net_timestamp() __net_timestamp() uses ktime_get_real(), while fq expects packets using CLOCK_MONOTONIC base. The fix is to clear skb->tstamp in forwarding paths. Fixes: 80b14dee ("net: Add a new socket option for a future transmit time.") Fixes: fb420d5d ("tcp/fq: move back to CLOCK_MONOTONIC") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Sergey Matyukevich <geomatsi@gmail.com> Tested-by: Sergey Matyukevich <geomatsi@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Robert P. J. Day authored
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michal Kubecek authored
Since commit 7969e5c4 ("ip: discard IPv4 datagrams with overlapping segments.") IPv4 reassembly code drops the whole queue whenever an overlapping fragment is received. However, the test is written in a way which detects duplicate fragments as overlapping so that in environments with many duplicate packets, fragmented packets may be undeliverable. Add an extra test and for (potentially) duplicate fragment, only drop the new fragment rather than the whole queue. Only starting offset and length are checked, not the contents of the fragments as that would be too expensive. For similar reason, linear list ("run") of a rbtree node is not iterated, we only check if the new fragment is a subset of the interval covered by existing consecutive fragments. v2: instead of an exact check iterating through linear list of an rbtree node, only check if the new fragment is subset of the "run" (suggested by Eric Dumazet) Fixes: 7969e5c4 ("ip: discard IPv4 datagrams with overlapping segments.") Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jörgen Storvist authored
Added support for the Telit LN940 series cellular modules QMI interface. QMI_QUIRK_SET_DTR quirk requied for Qualcomm MDM9x40 chipset. Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jörgen Storvist authored
Added support for Fibocom NL668 series QMI interface. Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x07 chipsets. Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller authored
Alexei Starovoitov says: ==================== pull-request: bpf 2018-12-15 The following pull-request contains BPF updates for your *net* tree. The main changes are: 1) fix liveness propagation of callee saved registers, from Jakub. 2) fix overflow in bpf_jit_limit knob, from Daniel. 3) bpf_flow_dissector api fix, from Stanislav. 4) bpf_perf_event api fix on powerpc, from Sandipan. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 14 Dec, 2018 4 commits
-
-
Cong Wang authored
tipc_wait_for_cond() drops socket lock before going to sleep, but tsk->group could be freed right after that release_sock(). So we have to re-check and reload tsk->group after it wakes up. After this patch, tipc_wait_for_cond() returns -ERESTARTSYS when tsk->group is NULL, instead of continuing with the assumption of a non-NULL tsk->group. (It looks like 'dsts' should be re-checked and reloaded too, but it is a different bug.) Similar for tipc_send_group_unicast() and tipc_send_group_anycast(). Reported-by: syzbot+10a9db47c3a0e13eb31c@syzkaller.appspotmail.com Fixes: b7d42635 ("tipc: introduce flow control for group broadcast messages") Fixes: ee106d7f ("tipc: introduce group anycast messaging") Fixes: 27bd9ec0 ("tipc: introduce group unicast messaging") Cc: Ying Xue <ying.xue@windriver.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dave Taht authored
While most distributions long ago switched to the iproute2 suite of utilities, which allow class-e (240.0.0.0/4) address assignment, distributions relying on busybox, toybox and other forms of ifconfig cannot assign class-e addresses without this kernel patch. While CIDR has been obsolete for 2 decades, and a survey of all the open source code in the world shows the IN_whatever macros are also obsolete... rather than obsolete CIDR from this ioctl entirely, this patch merely enables class-e assignment, sanely. Signed-off-by: Dave Taht <dave.taht@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Gustavo A. R. Silva authored
vr.mifi is indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: net/ipv6/ip6mr.c:1845 ip6mr_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap) net/ipv6/ip6mr.c:1919 ip6mr_compat_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap) Fix this by sanitizing vr.mifi before using it to index mrt->vif_table' Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Arnd Bergmann authored
The get_mac_address() function is normally inline, but when it is not, we get a warning that this configuration is broken: WARNING: vmlinux.o(.text+0x4aff00): Section mismatch in reference from the function w90p910_ether_setup() to the function .init.text:get_mac_address() The function w90p910_ether_setup() references the function __init get_mac_address(). This is often because w90p910_ether_setup lacks a __init Remove the __init to make it always do the right thing. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-