- 20 Aug, 2017 40 commits
-
-
Sean Young authored
The gpio-ir-recv driver does many wakeups (once per edge); the saa7134 driver has special handling to only wakeup 15ms after the first edge. Make this part of rc-core so gpio-ir-recv also benefits from this (so a rc-5 keypress now causes 3 wakeups rather than 24). Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Sean Young authored
We're reading beyond the buffer before checking its length. BUG: KASAN: slab-out-of-bounds in wbcir_irq_tx Signed-off-by:
-
Sean Young authored
This causes out-of-bounds read on device probe. BUG: KASAN: slab-out-of-bounds in mceusb_dev_printdata+0xdc/0x830 [mceusb] Signed-off-by:
-
Sean Young authored
This driver cannot send pulse, it only accepts driver-dependent codes. Cc: <stable@vger.kernel.org> # v3.2 Signed-off-by:
-
Shawn Guo authored
It adds the remote control driver and corresponding keymap file for IRDEC block found on ZTE ZX family SoCs. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Shawn Guo authored
It adds the dt-bindings document for ZTE ZX IRDEC remote control block. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Shawn Guo authored
The NEC scancode composing and protocol type detection in ir_nec_decode() is generic enough to be a shared function. Let's create an inline function in rc-core.h, so that other remote control drivers can reuse this function to save some code. Signed-off-by:
-
Philipp Zabel authored
Commit a53e35db ("reset: Ensure drivers are explicit when requesting reset lines") started to transition the reset control request API calls to explicitly state whether the driver needs exclusive or shared reset control behavior. Convert all drivers requesting exclusive resets to the explicit API call so the temporary transition helpers can be removed. No functional changes. Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Philipp Zabel authored
Commit a53e35db ("reset: Ensure drivers are explicit when requesting reset lines") started to transition the reset control request API calls to explicitly state whether the driver needs exclusive or shared reset control behavior. Convert all drivers requesting exclusive resets to the explicit API call so the temporary transition helpers can be removed. No functional changes. Cc: Patrice Chotard <patrice.chotard@st.com> Signed-off-by:
-
Heiner Kallweit authored
Transmit support in this driver was never tested and based on the code it can't work. Just one example: The buffer provided to nvt_tx_ir holds unsigned int values in micro seconds: First value is for a pulse, second for a pause, etc. Bytes in this buffer are copied as-is to the chip FIFO what can't work as the chip-internal format is totally different. See also conversion done in nvt_process_rx_ir_data. Even if we would try to fix this we have the issue that we can't test it. There seems to be no device on the market using IR transmit with one of the chips supported by this driver. To facilitate maintenance of the driver I'd propose to remove the rudimentary transmit support. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Yves Lemée authored
According the coding style guidelines, the ENOSYS error code must be returned in case of a non existent system call. This code has been replaced with the ENOTTY error code indicating a missing functionality. Signed-off-by:
Yves Lemée <yves.lemee.kernel@gmail.com> Signed-off-by:
-
Sean Young authored
Document the device tree bindings for the GPIO IR Bit Banging Transmitter. Signed-off-by:
-
Sean Young authored
Document the device tree bindings for the PWM IR Transmitter. Signed-off-by:
-
Sean Young authored
This is new driver which uses pwm, so it is more power-efficient than the bit banging gpio-ir-tx driver. Signed-off-by:
Pavel Machek <pavel@ucw.cz> Tested-by:
Matthias Reichl <hias@horus.com> Signed-off-by:
-
Sean Young authored
This is a simple bit-banging GPIO IR TX driver. Signed-off-by:
-
Sean Young authored
Without this patch, an input device is created which is not necessary. Signed-off-by:
-
Sean Young authored
When an ir-spi is registered, you get this message. rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0 "Unspecified device" refers to input_name, which makes no sense for IR TX only devices. So, rename to device_name. Also make driver_name const char* so that no casts are needed anywhere. Now ir-spi reports: rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0 Signed-off-by:
-
Arvind Yadav authored
attribute_groups are not supposed to change at runtime. All functions working with attribute_groups provided by <linux/sysfs.h> work with const attribute_group. So mark the non-const structs as const. File size before: text data bss dec hex filename 11605 880 20 12505 30d9 drivers/media/rc/rc-main.o File size After adding 'const': text data bss dec hex filename 11797 720 20 12537 30f9 drivers/media/rc/rc-main.o Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by:
-
Arvind Yadav authored
attribute_groups are not supposed to change at runtime. All functions working with attribute_groups provided by <linux/sysfs.h> work with const attribute_group. So mark the non-const structs as const. File size before: text data bss dec hex filename 18551 2256 77 20884 5194 drivers/media/rc/imon.o File size After adding 'const': text data bss dec hex filename 18679 2160 77 20916 51b4 drivers/media/rc/imon.o Signed-off-by:
-
Gustavo A. R. Silva authored
Remove unnecessary static on local variable delt. Such variable is initialized before being used, on every execution path throughout the function. The static has no benefit and, removing it reduces the code size. This issue was detected using Coccinelle and the following semantic patch: @bad exists@ position p; identifier x; type T; @@ static T x@p; ... x = <+...x...+> @@ identifier x; expression e; type T; position p != bad.p; @@ -static T x@p; ... when != x when strict ?x = e; In the following log you can see the difference in the code size. Also, there is a significant difference in the bss segment. This log is the output of the size command, before and after the code change: before: text data bss dec hex filename 5009 3456 576 9041 2351 drivers/media/rc/sir_ir.o after: text data bss dec hex filename 4988 3400 512 8900 22c4 drivers/media/rc/sir_ir.o Signed-off-by:Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by:
-
Sean Young authored
There is no dependency between the two, so remove the dependency in Kconfig files. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Sean Wang authored
I work for MediaTek on maintaining the MediaTek CIR driver for the existing SoCs and adding support for the following SoCs. Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
-
Sean Wang authored
This patch adds driver for CIR controller on MT7622 SoC. It has similar handling logic as the previously MT7623 does, but there are some differences in the register and field definition. So for ease portability and maintenance, those differences all are being kept inside the platform data as other drivers usually do. Currently testing successfully on NEC and SONY remote controller. Signed-off-by:
-
Sean Wang authored
This patch is the preparation patch in order to adapt into various hardware through adding platform data which holds specific characteristics and differences among MediaTek supported CIR devices instead of the old way defining those data in the static way as macro has. And the existing logic would be slightly changed to operate on those data which the actual device depends on. Signed-off-by:
-
Sean Wang authored
Document the devicetree bindings for CIR on MediaTek MT7622 SoC. Signed-off-by:
-
David Härdeman authored
The NEC decoder and the Sanyo decoders check if dev->keypressed is true before calling rc_repeat (without holding dev->keylock). Meanwhile, the XMP and JVC decoders do no such checks. This patch makes sure all users of rc_repeat() do so consistently by removing extra checks in NEC/Sanyo and modifying the check a bit in rc_repeat() so that no input event is generated if the key isn't pressed. Signed-off-by:
David Härdeman <david@hardeman.nu> Signed-off-by:
-
Kieran Bingham authored
The configuration of the pipeline and entities directly affects the inputs required to each entity for the partition algorithm. Thus it makes sense to involve those entities in the decision making process. Extend the entity ops API to provide an optional .partition() operation. This allows entities that affect the partition window to adapt the window based on their configuration. Entities implementing this operation must update the window parameter in place, which will then be passed up the pipeline. This creates a process whereby each entity describes what is required to satisfy the required output to its predecessor in the pipeline. Signed-off-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Hans Verkuil <hansverk@cisco.com> Signed-off-by:
-
Kieran Bingham authored
Provide register definitions required for UDS phase and partition algorithm support. The registers and bits defined here are available on Gen3 hardware only. Signed-off-by:
-
Kieran Bingham authored
As we develop the partition algorithm, we need to store more information per partition to describe the phase and other parameters. To keep this data together, further abstract the existing v4l2_rect into a partition specific structure. As partitions only have horizontal coordinates, store the left and width values only. When generating the partition windows, operate directly on the partition struct rather than copying and duplicating the processed data Signed-off-by:
-
Kieran Bingham authored
The vsp1_pipe object context variables for div_size and current_partition allowed state to be maintained through processing the partitions during processing. Now that the partition tables are calculated during stream on, there is no requirement to store these variables in the pipe object. Utilise local variables for the processing as required. Signed-off-by:
-
Kieran Bingham authored
Previously the active window and partition sizes for each partition were calculated for each partition every frame. This data is constant and only needs to be calculated once at the start of the stream. Extend the vsp1_pipe object to dynamically store the number of partitions required and pre-calculate the partition sizes into this table. Signed-off-by:
-
Kieran Bingham authored
Separate the code change from the function move so that code changes can be clearly identified. This commit has no functional change. The partition algorithm functions will be changed, and vsp1_video_pipeline_setup_partitions() will call vsp1_video_partition(). To prepare for that, move the function without any code change. Signed-off-by:
-
Kieran Bingham authored
Presently any received buffers are only released back to vb2 if vsp1_video_stop_streaming() is called. If vsp1_video_start_streaming() encounters an error, we will be warned by the vb2 handlers that buffers have not been returned. Move the buffer cleanup code to its own function to prevent duplication and call from both vsp1_video_stop_streaming() and the error path in vsp1_video_start_streaming(). Signed-off-by:
-
Chiranjeevi Rapolu authored
Previously, vblank range given to user was too big, falling outside of permissible range for a given resolution. Sometimes, too low vblank resulted in errors. Now, limit vblank to only permissible range for a given resolution. This change limits lower-bounds of vblank, doesn't affect upper bounds. Signed-off-by:
Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Chiranjeevi Rapolu authored
Previously, vblank range given to user was too big, falling outside of permissible range for a given resolution. Sometimes, too low vblank resulted in errors. Now, limit vblank to only permissible range for a given resolution. This change limits lower-bounds of vblank, doesn't affect upper bounds. Signed-off-by:
-
Sakari Ailus authored
The et8ek8 driver combines I²C register writes to a single array that it passes to i2c_transfer(). The maximum number of writes is 48 at once, decrease it to 8 and make more transfers if needed. Signed-off-by:
-
Julia Lawall authored
The v4l2_subdev_ops structure is only passed as the third argument of v4l2_i2c_subdev_init, which is const, so the v4l2_subdev_ops structure can be const as well. The other structures are only stored in the v4l2_subdev_ops structure, all the fields of which are const, so these structures can also be const. Done with the help of Coccinelle. Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Julia Lawall authored
The v4l2_subdev_ops structure is only passed as the third argument of v4l2_i2c_subdev_init, which is const, so the v4l2_subdev_ops structure can be const as well. The other structures are only stored in the v4l2_subdev_ops structure, all the fields of which are const, so these structures can also be const. Done with the help of Coccinelle. Signed-off-by:
-
Chiranjeevi Rapolu authored
Previously, pixel-rate/(pixels-per-line * lines-per-frame) was yielding incorrect frame timing for the user. OV sensor is using internal timing and this requires conversion (internal timing -> PPL) for correct HBLANK calculation. Now, change pixels-per-line domain from internal sensor clock to pixels domain. Set HBLANK read-only because fixed PPL is used for all resolutions. And, use more accurate link-frequency 422.4MHz instead of rounding down to 420MHz. Signed-off-by:
Tomasz Figa <tfiga@chromium.org> Signed-off-by:
-
Arvind Yadav authored
serio_device_id are not supposed to change at runtime. All functions working with serio_device_id provided by <linux/serio.h> work with const serio_device_id. So mark the non-const structs as const. Signed-off-by:
-
