Merge tag 'mvebu-dt64-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt

mvebu dt64 for 5.16 (part 1)

Add support for Globalscale MOCHAbin an Armada 7040 based development
board.

* tag 'mvebu-dt64-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
  arm64: dts: marvell: add Globalscale MOCHAbin

Link: https://lore.kernel.org/r/877deemefy.fsf@BL-laptopSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'stm32-dt-for-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt

STM32 DT for v5.16, round 1

Highlights:
----------

- MPU:
 - ST boards:
  - Add new stm32mp135f-dk board. It embedds new STM32MP135 SoC,
    with 512 MB of DDR3. Several connections are available on this
    board:
    4*USB2.0, 1*USB2.0 typeC DRD, SDcard, 2*RJ45, HDMI,
    Combo Wifi/BT, ...
    Only SD card, uart4 (console) and watchdog IPs are enabled in
    this tag.
  - Change IRQ level for STUSB1600 on DKx boards.
  - Fix SAI subclocks range.
  - Add ck_usb0_48m clock in USB OHCI node device to match with
    STM32MP15 datasheet.

 - DH boards:
  - Reduce DHCOR SPI NOR frequency to 50 MHz to avoid sporadic issues.
  - Fix SAI pin muxing.

 - Odyssey:
  - Set DCMI pins.

* tag 'stm32-dt-for-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
  ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151
  ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
  ARM: dts: stm32: fix SAI sub nodes register range
  ARM: dts: stm32: fix STUSB1600 Type-C irq level on stm32mp15xx-dkx
  ARM: dts: stm32: set the DCMI pins on stm32mp157c-odyssey
  ARM: dts: stm32: Reduce DHCOR SPI NOR frequency to 50 MHz
  ARM: dts: stm32: add initial support of stm32mp135f-dk board
  dt-bindings: stm32: document stm32mp135f-dk board
  ARM: dts: stm32: add STM32MP13 SoCs support

Link: https://lore.kernel.org/r/9d52c3e2-a3b9-89f3-1896-7cd3560e7010@foss.st.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-arm-dt-for-v5.16-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas ARM DT updates for v5.16 (take two)

  - SPI Multi I/O Bus, SDHI, and Ethernet support for the RZ/G2L SoC,
  - SPI Multi I/O Bus, camera, and video-on support for the R-Car V3U
    SoC,
  - SPI FLASH support for the Falcon development board,
  - eMMC, microSD, and Ethernet support for the RZ/G2L SMARC EVK
    development board,
  - 2 GHz High-Performance support for the R-Car H3e-2G, M3e-2G, and
    M3Ne-2G SoCs,
  - Miscellaneous fixes and improvements.

* tag 'renesas-arm-dt-for-v5.16-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  mailmap: Fix text encoding for Niklas Söderlund
  arm64: dts: renesas: rcar-gen3e: Add Cortex-A57 2 GHz opps
  arm64: dts: renesas: rzg2l-smarc-som: Enable Ethernet
  arm64: dts: renesas: r9a07g044: Add GbEthernet nodes
  arm64: dts: renesas: Add ports node to all adv7482 nodes
  arm64: dts: renesas: r8a779a0: Add and connect all CSI-2, ISP and VIN nodes
  arm64: dts: renesas: rzg2l-smarc: Enable microSD on SMARC platform
  arm64: dts: renesas: rzg2l-smarc-som: Enable eMMC on SMARC platform
  arm64: dts: renesas: r9a07g044: Add SDHI nodes
  arm64: dts: renesas: falcon-cpu: Add SPI flash via RPC
  arm64: dts: renesas: r8a779a0: Add RPC node
  arm64: dts: renesas: r9a07g044: Add SPI Multi I/O Bus controller node

Link: https://lore.kernel.org/r/cover.1634298094.git.geert+renesas@glider.beSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'aspeed-5.16-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc into arm/dt

ASPEED device tree updates for 5.15

 - New machines:

  * TYAN S7106 BMC, a x86 server from about four years ago

 - Descriptions for the AST2600 ADC, which now has an upstream driver

 - Lots of GPIO line names. The OpenBMC project has adopted a scheme for
   naming the lines, and new additions will follow this guide

 - New I2C devices for Rainier, Everest, EthanolX, Mt Jade

 - Fixes for fp5280g2 which has seen some recent development, including
   the addtion of a QEmu machine for testing

* tag 'aspeed-5.16-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc:
  ARM: dts: aspeed: fp5280g2: Use the 64M layout
  ARM: dts: aspeed: Add TYAN S7106 BMC machine
  ARM: dts: aspeed: rainier: Add power-config-full-load gpio
  ARM: dts: aspeed: p10bmc: Define secure boot gpio
  ARM: dts: aspeed: mtjade: Add some gpios
  ARM: dts: aspeed: Add ADC for AST2600 and enable for Rainier and Everest
  ARM: dts: everest: Define name for gpio line B6
  ARM: dts: everest: Define name for gpio line Q2
  ARM: dts: rainier: Define name for gpio line Q2
  ARM: dts: everest: Add 'factory-reset-toggle' as GPIOF6
  ARM: dts: aspeed: everest: Add I2C bus 15 muxes
  ARM: dts: aspeed: rainier: Add system LEDs
  ARM: dts: aspeed: amd-ethanolx: Add FRU EEPROM
  ARM: dts: fp5280g2: Enable KCS 3 for MCTP binding

Link: https://lore.kernel.org/r/CACPK8XdrMzY9tzdof7KpzxKquTo7GcWW4N9Zqwtmmu73C7htXA@mail.gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

ARM64: DT: HiSilicon ARM64 DT updates for 5.16

- Add SPMI PMIC support for the Hikey970 board
- Correct the sp805 watchdog compatible string to match the document
- Correct the operating-points table name to match the dtschema

* tag 'hisi-arm64-dt-for-5.16' of git://github.com/hisilicon/linux-hisi:
  arm64: dts: hisilicon: align operating-points table name with dtschema
  arm64: dts: hisilicon: fix arm,sp805 compatible string
  arm64: dts: hisilicon: Add support for Hikey 970 PMIC

Link: https://lore.kernel.org/r/6168EB53.60503@hisilicon.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'ux500-dts-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt

Ux500 DTS updates:

- Flag the janice SPI display lines properly for the right line
  semantics.
- Fix some errors in the Skomer regulator configuration.
- Fix some SD card pin configurations on Skomer.
- Assign the Skomer SD card a 300 ms power-on delay.
- Rewrite the battery nodes to use the standard binding
  "monitored-battery" as used in the updated bindings, and
  provide the right Samsung battery compatibles for the Samsung
  phones.

* tag 'ux500-dts-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
  ARM: dts: ux500: Switch battery nodes to standard
  ARM: dts: ux500: Skomer eMMC needs 300 ms power on
  ARM: dts: ux500: Fix up SD card pin config
  ARM: dts: ux500: Skomer regulator fixes
  ARM: dts: ux500: Tag Janice display SPI correct

Link: https://lore.kernel.org/r/CACRpkdYf5GwRvG1Gemk4mE+aw6UnAVTY8OudwsVNPQXThHXu6g@mail.gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.16, please pull the following:

- Rafal updates the BCM4908 DTS files to produce fewer warnings by
fixing the UART clock name, moving the reboot syscon node out of the bus
node, and finally updating the NAND controller node names.

* tag 'arm-soc/for-5.16/devicetree-arm64' of https://github.com/Broadcom/stblinux:
  arm64: dts: broadcom: bcm4908: Fix UART clock name
  arm64: dts: broadcom: bcm4908: Move reboot syscon out of bus
  arm64: dts: broadcom: bcm4908: Fix NAND node name

Link: https://lore.kernel.org/r/20211013174016.831348-2-f.fainelli@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.16, please pull the following:

- Matthew provides a set of updates to the Northstar Plus Device Tree
files to fix a number of warnings, and prepare the files to support the
addition of the Cisco Meraki MX64/MX65 wireless controller devices and
finally adds support for those boards.

- Rafal continues to provide updates to the BCM5301X Device Tree files
in order to fix warnings with the various node names, MDIO muxes and
memory nodes. He also adds support for the external switches on the
BCM53573 SoC and adds Tenda AC9 switch ports.

- Christian provides the description of the Ethernet switch ports for
the Cisco Meraki MR32 based on the 53016 SoC

- Arinc adds support for the Asus RT-AC88U device based on the BCM4709
and featuring 8 Ethernet ports over the integrated and the external
Realtek switch (not supported yet)

- Stefan adds support for the Raspberry Pi Compute Module 4 IO board and
does a number of preparatory changes to get there to the Device Tree
files before doing the actual addition

* tag 'arm-soc/for-5.16/devicetree' of https://github.com/Broadcom/stblinux: (31 commits)
  arm64: dts: broadcom: Add reference to RPi CM4 IO Board
  ARM: dts: Add Raspberry Pi Compute Module 4 IO Board
  ARM: dts: Add Raspberry Pi Compute Module 4
  dt-bindings: arm: bcm2835: Add Raspberry Pi Compute Module 4
  ARM: dts: bcm283x-rpi: Move Wifi/BT into separate dtsi
  dt-bindings: display: bcm2835: add optional property power-domains
  ARM: dts: BCM5301X: Add DT for Asus RT-AC88U
  ARM: BCM53016: MR32: get mac-address from nvmem
  ARM: BCM53016: Specify switch ports for Meraki MR32
  ARM: dts: BCM53573: Add Tenda AC9 switch ports
  ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch
  ARM: dts: BCM5301X: Specify switch ports for more devices
  ARM: dts: NSP: Fix MX65 MDIO mux warnings
  ARM: dts: NSP: Fix MX64/MX65 eeprom node name
  ARM: dts: NSP: Fix MDIO mux node names
  ARM: dts: NSP: Fix mpcore, mmc node names
  ARM: dts: NSP: Add bcm958623hr board name to dts
  ARM: dts: BCM5301X: Fix memory nodes names
  ARM: dts: BCM5301X: Fix MDIO mux binding
  ARM: dts: BCM5301X: Fix nodes names
  ...

Link: https://lore.kernel.org/r/20211013174016.831348-1-f.fainelli@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'samsung-dt64-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt

Samsung DTS ARM64 changes for v5.16

1. Match Exynos5433 DTS with dtschema.
2. Add an Exynos Auto v9 SoC and SADK board. The Exynos Auto v9 is a
   design for automotive for In-vehicle Infotainments (IVI) and Advanced
   Driver-Assistance Systems (ADAS).
   This pull request brings very basic support (pinctrl, UART and UFS
   storage) with a development SADK (Samsung Automotive Development Kit)
   board.

* tag 'samsung-dt64-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  arm64: dts: exynos: add minimal support for exynosautov9 sadk board
  arm64: dts: exynos: add initial support for exynosautov9 SoC
  arm64: dts: exynos: add proper comaptible FSYS syscon in Exynos5433
  arm64: dts: exynos: align operating-points table name with dtschema in Exynos5433

Link: https://lore.kernel.org/r/20211013162418.43072-2-krzysztof.kozlowski@canonical.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Samsung DTS ARM changes for v5.16

Minor cleanups - from undocumented or unused properties, coding style.

* tag 'samsung-dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: dts: exynos: use spaces instead of tabs around '='
  ARM: dts: exynos: remove unneeded DVS voltages from PMIC on Arndale
  ARM: dts: exynos: drop undocumented samsung,sata-freq property in Exynos5250

Link: https://lore.kernel.org/r/20211013162418.43072-1-krzysztof.kozlowski@canonical.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'qcom-arm64-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt

Qualcomm ARM64 dts updates for v5.16

MSM8916 gained some DT cleanup fixes. The Dragonboard 410c gains updated
firmware paths to the device specific firmware for modem and WiFi, to
allow these to be pushed to linux-next. The Longcheer L8150 gains extcon
support and the interrupt configuration for the accelerometer and
magnetometer are corrected.

MSM8998 gained descriptions for the multimedia clock controller and
iommu, as well as the GPU and its dedicated IOMMU. The QFPROM node is
updated to access the CRC corrected value space, the white LED (for
backlight) found in PMI8998 is described and GCC gains references to the
missing XO and sleep_clk reference clocks.
On top of this initial support for the Fxtec Pro1 QX1000 is added and
then the Sony Xperia XZ1, Xperia XZ1 Compact and the Xperia XZ Premium,
with USB, touchscreen, SDHCI, Bluetooth and vibrator supported.

The Xiaomi Mi 5 and Xiaomi Mi Note 2, based on the MSM8996 platform was
added, with support for frame buffer, GPU, audio, video encoder/decoder
and touchscreen.

The USB controller and PHY found in IPA6018 is described to provide USB
support. IPQ8074 gains a description of the SPMI controller.

The highlight on SC7180 is the introduction of the just released
"Homestar" device.  CPU power coefficients are corrected based on
measurements, IMEM is described to ensure that remoteproc relocation
information is carried to post mortem debug tools and a few smaller
fixes are introduced.

The SC7280 gains QSPI, low speed (i2c/spi/uart), GPU, thermal zones,
modem, CPU topology and updated memory map.

On SDM845 the "Limits hardware" is described and increases the
throttling temperature of the hardware from ~70C to 95C, with up to 30%
improvement in benchmarks as result.  Relying on hardware throttling and
thermal pressure, the CPU cooling devices are dropped.
The power for the second WiFi channel is properly described for the
Lenovo Yoga C630, to ensure they are both powered.

reboot-modes are defined for the PM660 PMIC, found in SDM630 and SDM660.

Initial support for the Snapdragon 690 (aka SM6350) is introduced, with
support for clocks, regulators, pinctrl, storage, thermal sensors, USB,
SMMU and CPUfreq. On top of this support for the Sony Xperia 10 III is
introduced.

* tag 'qcom-arm64-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (99 commits)
  arm64: dts: qcom: sdm630-nile: Correct regulator label name
  arm64: dts: qcom: sm6125: Improve indentation of multiline properties
  arm64: dts: qcom: msm8916-longcheer-l8150: Use &pm8916_usbin extcon
  arm64: dts: qcom: pm8916: Add pm8941-misc extcon for USB detection
  arm64: dts: qcom: pm8916: Remove wrong reg-names for rtc@6000
  arm64: dts: qcom: sc7280: Update Q6V5 MSS node
  arm64: dts: qcom: sc7280: Add Q6V5 MSS node
  arm64: dts: qcom: sc7280: Add nodes to boot modem
  arm64: dts: qcom: sc7280: Add/Delete/Update reserved memory nodes
  arm64: dts: qcom: sc7280: Update reserved memory map
  arm64: dts: qcom: msm8998-fxtec-pro1: Add tlmm keyboard keys
  arm64: dts: qcom: msm8998-fxtec-pro1: Add Goodix GT9286 touchscreen
  arm64: dts: qcom: msm8998-fxtec-pro1: Add physical keyboard leds
  arm64: dts: qcom: Add support for MSM8998 F(x)tec Pro1 QX1000
  arm64: dts: qcom: msm8916: Fix Secondary MI2S bit clock
  arm64: dts: qcom: msm8916-longcheer-l8150: Add missing sensor interrupts
  arm64: dts: qcom: sc7180: Add IMEM and pil info regions
  arm64: dts: qcom: pm6150l: Add missing include
  arm64: dts: qcom: sm6350: Add device tree for Sony Xperia 10 III
  arm64: dts: qcom: sm6350: Add apps_smmu and assign iommus prop to USB1
  ...

Link: https://lore.kernel.org/r/20211012231155.1036519-1-bjorn.andersson@linaro.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'qcom-dts-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt

Qualcomm DTS updates for v5.16

This extends the previous limited description of MSM8226 with SDHC,
UART, I2C, SCM, SMEM, RPM and basic PMIC definitions. Based on this,
initial support for the LG G Watch R smartwatch is introduced.

APQ8064 gets a couple of DT updates, one which will allow the GPU driver
to drop supporting legacy "opp tables" in the future.

DT bindings and DTS files are updated with additional compatibles, for
completeness.

* tag 'qcom-dts-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  dt-bindings: arm: qcom, add missing devices
  ARM: dts: qcom: msm8974: Add xo_board reference clock to DSI0 PHY
  ARM: dts: qcom: fill secondary compatible for multiple boards
  ARM: dts: qcom: apq8064: adjust memory node according to specs
  ARM: dts: qcom: apq8064: Convert adreno from legacy gpu-pwrlevels to opp-v2
  ARM: dts: qcom: Add support for LG G Watch R
  dt-bindings: arm: qcom: Document APQ8026 SoC binding
  ARM: dts: qcom: Add pm8226 PMIC
  ARM: dts: qcom: msm8226: Add more SoC bits
  dt-bindings: arm: qcom: Document SDX65 platform and boards

Link: https://lore.kernel.org/r/20211012174310.1017857-1-bjorn.andersson@linaro.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'v5.15-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt

Biggest change is, that we have now support for a reset controller inside the
mmsys. This goes inhand with changes to the driver, that you will find in the
soc pull request.

Mediatek PCI device tree binding described the root port in a wrong. The IP
actaully implements several root complex with everyone having a single root port.

We need to fix the DT in an incompatible way to describe the HW as it is. This
also fixes a problem that no IRQ bigger then 32 could be handled.

The only public available HW that is affected by this is the BananaPi R64. I'm
not aware that there is a big user base using the upstream kernel. In this
boards PCI is only used for extension cards, so I don't expect any boot problems.

- mt8173: add reset for dsi0 to mmsys
- move dt-bindings reset controller includes to correct folder
- split PCIe node to use new format for mt2712 and mt7622
- mt8183: add audio node to chromebook devices
- mt8192: add clock controller node

* tag 'v5.15-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
  arm64: dts: mt8183: Add the mmsys reset bit to reset the dsi0
  arm64: dts: mt8173: Add the mmsys reset bit to reset the dsi0
  dt-bindings: display: mediatek: add dsi reset optional property
  dt-bindings: mediatek: Add #reset-cells to mmsys system controller
  arm64: dts: mediatek: Move reset controller constants into common location
  arm64: dts: mediatek: Split PCIe node for MT2712 and MT7622
  arm64: dts: mt8183: add kukui platform audio node
  arm64: dts: mt8183: add audio node
  arm64: dts: mediatek: Add mt8192 clock controllers

Link: https://lore.kernel.org/r/1a3d63a3-c020-3319-26f6-a2ec338cc42e@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Referring to the note under USBH reset and clocks chapter of RM0436,
"In order to access USBH_OHCI registers it is necessary to activate the USB
clocks by enabling the PLL controlled by USBPHYC" (ck_usbo_48m).

The point is, when USBPHYC PLL is not enabled, OHCI register access
freezes the resume from STANDBY. It is the case when dual USBH is enabled,
instead of OTG + single USBH.
When OTG is probed, as ck_usbo_48m is USBO clock parent, then USBPHYC PLL
is enabled and OHCI register access is OK.

This patch adds ck_usbo_48m (provided by USBPHYC PLL) as clock of USBH
OHCI, thus USBPHYC PLL will be enabled and OHCI register access will be OK.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Fix SAI2A and SAI2B pin muxings for AV96 board on STM32MP15.
Change sai2a-4 & sai2a-5 to sai2a-2 & sai2a-2.
Change sai2a-4 & sai2a-sleep-5 to sai2b-2 & sai2b-sleep-2

Fixes: dcf185ca ("ARM: dts: stm32: Add alternate pinmux for SAI2 pins on stm32mp15")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The STM32 SAI subblocks registers offsets are in the range
0x0004 (SAIx_CR1) to 0x0020 (SAIx_DR).
The corresponding range length is 0x20 instead of 0x1c.
Change reg property accordingly.

Fixes: 5afd65c3 ("ARM: dts: stm32: add sai support on stm32mp157c")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

STUSB1600 IRQ (Alert pin) is active low (open drain). Interrupts may get
lost currently, so fix the IRQ type.

Fixes: 83686162 ("ARM: dts: stm32: add STUSB1600 Type-C using I2C4 on stm32mp15xx-dkx")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The Seeed Odyssey-STM32MP157C board has a 20-pin DVP camera output. The
DCMI pins used on this output are defined in the pin state definition
&pinctrl/dcmi-1, AKA &dcmi_pins_b (added in mainline commit
02814a41). Set these pins as the default
pinctrl of the DCMI peripheral in the board device tree.

The pins are not used for any other purpose, so it seems safe to assume
most users will not need to override (delete) what this patch provides.
status defaults to "disabled", so the peripheral will not be
unnecessarily started. And the users who actually intend to make use of
a camera on the DVP port will have this little part of the configuration
ready.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM,
which causes additional signal delay. At 108 MHz, this delay triggers
a sporadic issue where the first bit of RX data is not received by the
QSPI controller.

There are two options of addressing this problem, either by using the
DLYB block to compensate the extra delay, or by reducing the QSPI bus
clock frequency. The former requires calibration and that is overly
complex, so opt for the second option.

Fixes: 76045bc4 ("ARM: dts: stm32: Add QSPI NOR on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add support of stm32mp135f discovery board (part number: STM32MP135F-DK).
It embeds a STM32MP135F SOC with 512 MB of DDR3.
Several connections are available on this board:
    4*USB2.0, 1*USB2.0 typeC DRD, SDcard, 2*RJ45, HDMI, Combo Wifi/BT, ...

Only SD card, uart4 (console) and watchdog IPs are enabled in this commit.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>

Add new entry for stm32mp135f-dk board.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>

Add initial support of STM32MP13 family. The STM32MP13 SoC diversity is
composed by:
-STM32MP131:
  -core: 1*CA7, 17*TIMERS, 5*LPTIMERS, DMA/MDMA/DMAMUX
  -storage: 3*SDMCC, 1*QSPI, FMC
  -com: USB (OHCI/EHCI, OTG), 5*I2C, 5*SPI/I2S, 8*U(S)ART
  -audio: 2*SAI
  -network: 1*ETH(GMAC)
-STM32MP133: STM32MP131 + 2*CAN, ETH2(GMAC), ADC1
-STM32MP135: STM32MP133 + DCMIPP, LTDC

A second diversity layer exists for security features:
-STM32MP13xY, "Y" gives information:
 -Y = A/D means no cryp IP and no secure boot.
 -Y = C/F means cryp IP + secure boot.

This commit adds basic peripheral.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>

There are commits that mess up the encoding of 'ö' in Söderlund, add a
correct entry to .mailmap.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20211014212906.2331293-1-niklas.soderlund+renesas@ragnatech.seSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

This force-converts the per-device battery node into the standard
properties using "simple-battery" for the HREF machines and the
corresponding Samsung battery for the mobile phones.

This is fine to do since the battery data in the DTS files has never
been deployed or used. In commit a1149ae9
"ARM: ux500: Disable Power Supply and Battery Management by default"
it was turned off and has not been switched back on since. In
the meantime standardized bindings for batteries have appeared
making the old AB8500 battery bindings obsolete.

The battery node which is now in the middle of an included file
is obviously a per-device piece of information so push this down
to each board. The HREF machines all have the same battery and can
share a single node in the HREF dtsi file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add operating points for running the Cortex-A57 CPU cores on R-Car
H3e-2G, M3e-2G, and M3Ne-2G at 2 GHz.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/08a0f27f50b8ad4a78c05186190bebcfb364fe8f.1634200489.git.geert+renesas@glider.be

Enable Ethernet{0,1} interfaces on RZ/G2L SMARC EVK.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211013075647.32231-3-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add Gigabit Ethernet{0,1} nodes to SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211013075647.32231-2-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

The different port@ entries of the adv7482 nodes shall be encapsulated
in a ports node, add one.  This change does not change how the driver
parses the DT and no driver change is needed.

The change however makes it possible to validate the source files with a
correct json-schema.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20211012183431.718691-1-niklas.soderlund+renesas@ragnatech.seSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

The V3U have 32 VIN, 4 CSI-2 and 4 ISP nodes that interact with each
other for video capture. Add all nodes and record how they are
interconnected.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20211012100038.375289-1-niklas.soderlund+renesas@ragnatech.seSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Use the 64M layout since the flash on the board is 64M
Signed-off-by: John Wang <wangzhiqiang02@inspur.com>
Link: https://lore.kernel.org/r/20211014072743.939293-1-wangzhiqiang02@inspur.comSigned-off-by: Joel Stanley <joel@jms.id.au>

Globalscale MOCHAbin is a Armada 7040 based development board.

Specifications:
* Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
* 2 / 4 / 8 GB of DDR4 DRAM
* 16 GB eMMC
* 4MB SPI-NOR (Bootloader)
* 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
* 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
* 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
* 1x SATA 7+15 socket (SATA3)
* 1x 16-pin (2×8) MikroBus Connector
* 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
* 2x USB3.0 Type-A ports via SMSC USB5434B hub
* Cortex 2x5 JTAG
* microUSB port for UART (PL2303GL/PL2303SA onboard)
* 1x 10G SFP+
* 1x 1G SFP (Connected to 88E1512 PHY)
* 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
* 4x 1G RJ45 ports via Topaz 88E6141 switch
* RTC with battery holder (SoC provided, requires CR2032 battery)
* 1x 12V DC IN
* 1x Power switch
* 1x 12V fan header (3-pin, power only)
* 1x mini-PCIe LED header (2x0.1" pins)
* 1x M.2-2280 LED header (2x0.1" pins)
* 6x Bootstrap jumpers
* 1x Power LED (Green)
* 3x Tri-color RGB LEDs (Controllable)
* 1x Microchip ATECC608B secure element

Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
parallel connected to the same PHY.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

Merge tag 'ti-k3-dt-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux into arm/dt

Devicetree changes for TI K3 platforms for v5.16 merge window:

* New Platforms:
  - AM654: Siemens IOT2050 PG2 boards
  - J721E: Low cost SK board
* New features:
  - mmc aliases introduced
  - AM64 ICSSG nodes, mcu pinctrl added
* Fixes:
  - Schema fixups for pcie, thermal zones
  - Fixup to include board specific property for J721e-evm and j7200-evm
  - Misc fixups including cleaning up order in Makefile

* tag 'ti-k3-dt-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux: (24 commits)
  arm64: dts: ti: k3-j721e-sk: Add DDR carveout memory nodes
  arm64: dts: ti: k3-j721e-sk: Add IPC sub-mailbox nodes
  arm64: dts: ti: Add support for J721E SK
  dt-bindings: arm: ti: Add compatible for J721E SK
  arm64: dts: ti: iot2050: Add support for product generation 2 boards
  arm64: dts: ti: iot2050: Prepare for adding 2nd-generation boards
  dt-bindings: arm: ti: Add bindings for Siemens IOT2050 PG2 boards
  arm64: dts: ti: iot2050: Add/enabled mailboxes and carve-outs for R5F cores
  arm64: dts: ti: iot2050: Disable SR2.0-only PRUs
  arm64: dts: ti: iot2050: Flip mmc device ordering on Advanced devices
  arm64: dts: ti: k3-j7200-common-proc-board: Add j7200-evm compatible
  arm64: dts: ti: k3-j721e-common-proc-board: Add j721e-evm compatible
  dt-bindings: arm: ti: Add missing compatibles for j721e/j7200 evms
  arm64: dts: ti: Makefile: Collate AM64 platforms together
  arm64: dts: ti: k3-am64-main: Add ICSSG nodes
  arm64: dts: ti: k3-am65: Relocate thermal-zones to SoC specific location
  arm64: dts: ti: ti-k3*: Introduce aliases for mmc nodes
  arm64: dts: ti: k3-am65-main: Cleanup "ranges" property in "pcie" DT node
  arm64: dts: ti: j7200-main: Add *max-virtual-functions* for pcie-ep DT node
  arm64: dts: ti: j7200-main: Fix "bus-range" upto 256 bus number for PCIe
  ...

Link: https://lore.kernel.org/r/20211012120817.beqhp4tygnf3xyi5@wirelessSigned-off-by: Arnd Bergmann <arnd@arndb.de>

SADK(Samsung Automotive Development Kit) is the development kit to
evaluate Exynos Auto v9 SoC. It has 16GB LPDDR4 DRAM and two
256GB Samsung UFS. This patch enables only serial console and ufs0
device.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20211012002314.38965-4-chanho61.park@samsung.comSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>

Add minimal support for ExynosAuto v9 SoC[1].

- Enumarate all pinctrl nodes
- UART with exynos850 compatible
- UFS0 HCI + Phy

Like exynos850, this also uses fixed-rate clock nodes until clock driver
has been supported. The clock nodes are initialized on bootloader stage
thus we don't need to control them so far.

[1]: https://www.samsung.com/semiconductor/minisite/exynos/products/automotiveprocessor/exynos-auto-v9/Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20211012002314.38965-3-chanho61.park@samsung.comSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>

The TYAN S7106 is a server platform with an ASPEED AST2500 BMC.
Signed-off-by: Oskar Senft <osk@google.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210909004920.1634322-1-osk@google.comSigned-off-by: Joel Stanley <joel@jms.id.au>

Add the power-config-full-load described in:
https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md#power-config-full-load

The power-config-full-load gpio is designed to be used to specify how
many power supplies the system should have, in rainier it is 2 or 4.  If
enough power supplies fail so that the system no longer has redundancy
(no longer n+1), the hardware will signal to the Onboard Chip Controller
that the system may be oversubscribed, and performance may need to be
reduced so the system can maintain it's powered on state.
Signed-off-by: Adriana Kobylak <anoo@us.ibm.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20211005192226.213539-1-anoo@linux.ibm.comSigned-off-by: Joel Stanley <joel@jms.id.au>

Merge tag 'tegra-for-5.16-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt

ARM: tegra: Device tree changes for v5.16-rc1

This contains various cleanup patches to 32-bit ARM Tegra device trees
and enables USB OTG mode on the Nexus 7.

* tag 'tegra-for-5.16-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: Remove useless usb-ehci compatible string
  ARM: tegra: Remove unused backlight-boot-off property
  ARM: tegra: nexus7: Enable USB OTG mode
  ARM: tegra: Add new properties to USB PHY device-tree nodes
  ARM: tegra: Update Broadcom Bluetooth device-tree nodes
  ARM: tegra: acer-a500: Correct compatible of ak8975 magnetometer

Link: https://lore.kernel.org/r/20211008201132.1678814-6-thierry.reding@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

The patch uses the "dt-bindings/clock/sprd,ums512-clk.h header, which
is not merged yet. This caused a build regression, and it means the
patch was not ready to get merged anyway.

This reverts commit 23410de5.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

AT91 DT #1 for 5.16:

- Addition of a new variant in the sama5d2 family: the sama5d29 with
  significant updates being CAN and Ethernet controllers;
- Add support for Exegin Q5xR5 and CalAmp LMU5000 boards which were
  maintained up to this moment, separately, in OpenWrt tree;
- Two more boards gained I2C bus recovery support;
- Tse850 updated with one Ethernet fix;
- Sama7g5ek gained ADC nodes  and sama5d27_wlsom1 WiFi support.

* tag 'at91-dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
  ARM: at91: dts: sama5d29: Add dtsi file for sama5d29
  ARM: dts: at91-sama5d2_icp.dts: Added I2C bus recovery support
  ARM: dts: at91: tse850: the emac<->phy interface is rmii
  ARM: dts: at91: add Exegin Q5xR5 board
  dt-bindings: ARM: at91: document exegin q5xr5 board
  dt-bindings: add vendor prefix for exegin
  ARM: dts: at91: add CalAmp LMU5000 board
  dt-bindings: ARM: at91: document CalAmp LMU5000 board
  dt-bindings: add vendor prefix for calamp
  ARM: dts: at91: at91sam9260: add pinctrl label
  ARM: dts: at91-sama5d27_som1_ek: Added I2C bus recovery support
  ARM: dts: at91: sama7g5ek: enable ADC on the board
  ARM: dts: at91: sama7g5: add node for the ADC
  ARM: dts: at91: sama5d27_wlsom1: add wifi device

Link: https://lore.kernel.org/r/20211011123438.16562-1-nicolas.ferre@microchip.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'omap-for-v5.16/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt

Devicetree changes for omaps for v5.16

These changes configure devices for am335x and dra7, and fixes
various devicetree check warnings for gta04:

- Update am335x-pocketbeagle to use pinconf-single

- A series of devicetree warning fixes for omap3 and gta04

- Configure bb2d Vivante GC 2D Accelerator for dra7

* tag 'omap-for-v5.16/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: dra7: add entry for bb2d module
  arm: dts: omap3-gta04: cleanup led node names
  arm: dts: omap3-gta04a4: accelerometer irq fix
  arm: dts: omap3-gta04a5: fix missing sensor supply
  arm: dts: omap3-gta04: fix missing sensor supply
  arm: dts: omap3-gta04: cleanup LCD definition
  ARM: dts: omap3: fix cpu thermal label name
  ARM: dts: am335x-pocketbeagle: switch to pinconf-single

Link: https://lore.kernel.org/r/pull-1633950030-501948@atomide.com-3Signed-off-by: Arnd Bergmann <arnd@arndb.de>