- 19 Oct, 2021 12 commits
-
-
Arnd Bergmann authored
Merge tag 'stm32-dt-for-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt STM32 DT for v5.16, round 1 Highlights: ---------- - MPU: - ST boards: - Add new stm32mp135f-dk board. It embedds new STM32MP135 SoC, with 512 MB of DDR3. Several connections are available on this board: 4*USB2.0, 1*USB2.0 typeC DRD, SDcard, 2*RJ45, HDMI, Combo Wifi/BT, ... Only SD card, uart4 (console) and watchdog IPs are enabled in this tag. - Change IRQ level for STUSB1600 on DKx boards. - Fix SAI subclocks range. - Add ck_usb0_48m clock in USB OHCI node device to match with STM32MP15 datasheet. - DH boards: - Reduce DHCOR SPI NOR frequency to 50 MHz to avoid sporadic issues. - Fix SAI pin muxing. - Odyssey: - Set DCMI pins. * tag 'stm32-dt-for-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151 ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15 ARM: dts: stm32: fix SAI sub nodes register range ARM: dts: stm32: fix STUSB1600 Type-C irq level on stm32mp15xx-dkx ARM: dts: stm32: set the DCMI pins on stm32mp157c-odyssey ARM: dts: stm32: Reduce DHCOR SPI NOR frequency to 50 MHz ARM: dts: stm32: add initial support of stm32mp135f-dk board dt-bindings: stm32: document stm32mp135f-dk board ARM: dts: stm32: add STM32MP13 SoCs support Link: https://lore.kernel.org/r/9d52c3e2-a3b9-89f3-1896-7cd3560e7010@foss.st.comSigned-off-by:
Arnd Bergmann <arnd@arndb.de>
-
Arnd Bergmann authored
Merge tag 'renesas-arm-dt-for-v5.16-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt Renesas ARM DT updates for v5.16 (take two) - SPI Multi I/O Bus, SDHI, and Ethernet support for the RZ/G2L SoC, - SPI Multi I/O Bus, camera, and video-on support for the R-Car V3U SoC, - SPI FLASH support for the Falcon development board, - eMMC, microSD, and Ethernet support for the RZ/G2L SMARC EVK development board, - 2 GHz High-Performance support for the R-Car H3e-2G, M3e-2G, and M3Ne-2G SoCs, - Miscellaneous fixes and improvements. * tag 'renesas-arm-dt-for-v5.16-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: mailmap: Fix text encoding for Niklas Söderlund arm64: dts: renesas: rcar-gen3e: Add Cortex-A57 2 GHz opps arm64: dts: renesas: rzg2l-smarc-som: Enable Ethernet arm64: dts: renesas: r9a07g044: Add GbEthernet nodes arm64: dts: renesas: Add ports node to all adv7482 nodes arm64: dts: renesas: r8a779a0: Add and connect all CSI-2, ISP and VIN nodes arm64: dts: renesas: rzg2l-smarc: Enable microSD on SMARC platform arm64: dts: renesas: rzg2l-smarc-som: Enable eMMC on SMARC platform arm64: dts: renesas: r9a07g044: Add SDHI nodes arm64: dts: renesas: falcon-cpu: Add SPI flash via RPC arm64: dts: renesas: r8a779a0: Add RPC node arm64: dts: renesas: r9a07g044: Add SPI Multi I/O Bus controller node Link: https://lore.kernel.org/r/cover.1634298094.git.geert+renesas@glider.beSigned-off-by:
-
Arnd Bergmann authored
Merge tag 'aspeed-5.16-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc into arm/dt ASPEED device tree updates for 5.15 - New machines: * TYAN S7106 BMC, a x86 server from about four years ago - Descriptions for the AST2600 ADC, which now has an upstream driver - Lots of GPIO line names. The OpenBMC project has adopted a scheme for naming the lines, and new additions will follow this guide - New I2C devices for Rainier, Everest, EthanolX, Mt Jade - Fixes for fp5280g2 which has seen some recent development, including the addtion of a QEmu machine for testing * tag 'aspeed-5.16-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc: ARM: dts: aspeed: fp5280g2: Use the 64M layout ARM: dts: aspeed: Add TYAN S7106 BMC machine ARM: dts: aspeed: rainier: Add power-config-full-load gpio ARM: dts: aspeed: p10bmc: Define secure boot gpio ARM: dts: aspeed: mtjade: Add some gpios ARM: dts: aspeed: Add ADC for AST2600 and enable for Rainier and Everest ARM: dts: everest: Define name for gpio line B6 ARM: dts: everest: Define name for gpio line Q2 ARM: dts: rainier: Define name for gpio line Q2 ARM: dts: everest: Add 'factory-reset-toggle' as GPIOF6 ARM: dts: aspeed: everest: Add I2C bus 15 muxes ARM: dts: aspeed: rainier: Add system LEDs ARM: dts: aspeed: amd-ethanolx: Add FRU EEPROM ARM: dts: fp5280g2: Enable KCS 3 for MCTP binding Link: https://lore.kernel.org/r/CACPK8XdrMzY9tzdof7KpzxKquTo7GcWW4N9Zqwtmmu73C7htXA@mail.gmail.comSigned-off-by:
-
git://github.com/hisilicon/linux-hisiArnd Bergmann authored
ARM64: DT: HiSilicon ARM64 DT updates for 5.16 - Add SPMI PMIC support for the Hikey970 board - Correct the sp805 watchdog compatible string to match the document - Correct the operating-points table name to match the dtschema * tag 'hisi-arm64-dt-for-5.16' of git://github.com/hisilicon/linux-hisi: arm64: dts: hisilicon: align operating-points table name with dtschema arm64: dts: hisilicon: fix arm,sp805 compatible string arm64: dts: hisilicon: Add support for Hikey 970 PMIC Link: https://lore.kernel.org/r/6168EB53.60503@hisilicon.comSigned-off-by:
-
Arnd Bergmann authored
Merge tag 'ux500-dts-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt Ux500 DTS updates: - Flag the janice SPI display lines properly for the right line semantics. - Fix some errors in the Skomer regulator configuration. - Fix some SD card pin configurations on Skomer. - Assign the Skomer SD card a 300 ms power-on delay. - Rewrite the battery nodes to use the standard binding "monitored-battery" as used in the updated bindings, and provide the right Samsung battery compatibles for the Samsung phones. * tag 'ux500-dts-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik: ARM: dts: ux500: Switch battery nodes to standard ARM: dts: ux500: Skomer eMMC needs 300 ms power on ARM: dts: ux500: Fix up SD card pin config ARM: dts: ux500: Skomer regulator fixes ARM: dts: ux500: Tag Janice display SPI correct Link: https://lore.kernel.org/r/CACRpkdYf5GwRvG1Gemk4mE+aw6UnAVTY8OudwsVNPQXThHXu6g@mail.gmail.comSigned-off-by:
-
https://github.com/Broadcom/stblinuxArnd Bergmann authored
This pull request contains Broadcom ARM64-based SoCs Device Tree changes for 5.16, please pull the following: - Rafal updates the BCM4908 DTS files to produce fewer warnings by fixing the UART clock name, moving the reboot syscon node out of the bus node, and finally updating the NAND controller node names. * tag 'arm-soc/for-5.16/devicetree-arm64' of https://github.com/Broadcom/stblinux: arm64: dts: broadcom: bcm4908: Fix UART clock name arm64: dts: broadcom: bcm4908: Move reboot syscon out of bus arm64: dts: broadcom: bcm4908: Fix NAND node name Link: https://lore.kernel.org/r/20211013174016.831348-2-f.fainelli@gmail.comSigned-off-by:
-
https://github.com/Broadcom/stblinuxArnd Bergmann authored
This pull request contains Broadcom ARM-based SoCs Device Tree changes for 5.16, please pull the following: - Matthew provides a set of updates to the Northstar Plus Device Tree files to fix a number of warnings, and prepare the files to support the addition of the Cisco Meraki MX64/MX65 wireless controller devices and finally adds support for those boards. - Rafal continues to provide updates to the BCM5301X Device Tree files in order to fix warnings with the various node names, MDIO muxes and memory nodes. He also adds support for the external switches on the BCM53573 SoC and adds Tenda AC9 switch ports. - Christian provides the description of the Ethernet switch ports for the Cisco Meraki MR32 based on the 53016 SoC - Arinc adds support for the Asus RT-AC88U device based on the BCM4709 and featuring 8 Ethernet ports over the integrated and the external Realtek switch (not supported yet) - Stefan adds support for the Raspberry Pi Compute Module 4 IO board and does a number of preparatory changes to get there to the Device Tree files before doing the actual addition * tag 'arm-soc/for-5.16/devicetree' of https://github.com/Broadcom/stblinux: (31 commits) arm64: dts: broadcom: Add reference to RPi CM4 IO Board ARM: dts: Add Raspberry Pi Compute Module 4 IO Board ARM: dts: Add Raspberry Pi Compute Module 4 dt-bindings: arm: bcm2835: Add Raspberry Pi Compute Module 4 ARM: dts: bcm283x-rpi: Move Wifi/BT into separate dtsi dt-bindings: display: bcm2835: add optional property power-domains ARM: dts: BCM5301X: Add DT for Asus RT-AC88U ARM: BCM53016: MR32: get mac-address from nvmem ARM: BCM53016: Specify switch ports for Meraki MR32 ARM: dts: BCM53573: Add Tenda AC9 switch ports ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch ARM: dts: BCM5301X: Specify switch ports for more devices ARM: dts: NSP: Fix MX65 MDIO mux warnings ARM: dts: NSP: Fix MX64/MX65 eeprom node name ARM: dts: NSP: Fix MDIO mux node names ARM: dts: NSP: Fix mpcore, mmc node names ARM: dts: NSP: Add bcm958623hr board name to dts ARM: dts: BCM5301X: Fix memory nodes names ARM: dts: BCM5301X: Fix MDIO mux binding ARM: dts: BCM5301X: Fix nodes names ... Link: https://lore.kernel.org/r/20211013174016.831348-1-f.fainelli@gmail.comSigned-off-by:
-
Arnd Bergmann authored
Merge tag 'samsung-dt64-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt Samsung DTS ARM64 changes for v5.16 1. Match Exynos5433 DTS with dtschema. 2. Add an Exynos Auto v9 SoC and SADK board. The Exynos Auto v9 is a design for automotive for In-vehicle Infotainments (IVI) and Advanced Driver-Assistance Systems (ADAS). This pull request brings very basic support (pinctrl, UART and UFS storage) with a development SADK (Samsung Automotive Development Kit) board. * tag 'samsung-dt64-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: arm64: dts: exynos: add minimal support for exynosautov9 sadk board arm64: dts: exynos: add initial support for exynosautov9 SoC arm64: dts: exynos: add proper comaptible FSYS syscon in Exynos5433 arm64: dts: exynos: align operating-points table name with dtschema in Exynos5433 Link: https://lore.kernel.org/r/20211013162418.43072-2-krzysztof.kozlowski@canonical.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linuxArnd Bergmann authored
Samsung DTS ARM changes for v5.16 Minor cleanups - from undocumented or unused properties, coding style. * tag 'samsung-dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: ARM: dts: exynos: use spaces instead of tabs around '=' ARM: dts: exynos: remove unneeded DVS voltages from PMIC on Arndale ARM: dts: exynos: drop undocumented samsung,sata-freq property in Exynos5250 Link: https://lore.kernel.org/r/20211013162418.43072-1-krzysztof.kozlowski@canonical.comSigned-off-by:
-
Arnd Bergmann authored
Merge tag 'qcom-arm64-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt Qualcomm ARM64 dts updates for v5.16 MSM8916 gained some DT cleanup fixes. The Dragonboard 410c gains updated firmware paths to the device specific firmware for modem and WiFi, to allow these to be pushed to linux-next. The Longcheer L8150 gains extcon support and the interrupt configuration for the accelerometer and magnetometer are corrected. MSM8998 gained descriptions for the multimedia clock controller and iommu, as well as the GPU and its dedicated IOMMU. The QFPROM node is updated to access the CRC corrected value space, the white LED (for backlight) found in PMI8998 is described and GCC gains references to the missing XO and sleep_clk reference clocks. On top of this initial support for the Fxtec Pro1 QX1000 is added and then the Sony Xperia XZ1, Xperia XZ1 Compact and the Xperia XZ Premium, with USB, touchscreen, SDHCI, Bluetooth and vibrator supported. The Xiaomi Mi 5 and Xiaomi Mi Note 2, based on the MSM8996 platform was added, with support for frame buffer, GPU, audio, video encoder/decoder and touchscreen. The USB controller and PHY found in IPA6018 is described to provide USB support. IPQ8074 gains a description of the SPMI controller. The highlight on SC7180 is the introduction of the just released "Homestar" device. CPU power coefficients are corrected based on measurements, IMEM is described to ensure that remoteproc relocation information is carried to post mortem debug tools and a few smaller fixes are introduced. The SC7280 gains QSPI, low speed (i2c/spi/uart), GPU, thermal zones, modem, CPU topology and updated memory map. On SDM845 the "Limits hardware" is described and increases the throttling temperature of the hardware from ~70C to 95C, with up to 30% improvement in benchmarks as result. Relying on hardware throttling and thermal pressure, the CPU cooling devices are dropped. The power for the second WiFi channel is properly described for the Lenovo Yoga C630, to ensure they are both powered. reboot-modes are defined for the PM660 PMIC, found in SDM630 and SDM660. Initial support for the Snapdragon 690 (aka SM6350) is introduced, with support for clocks, regulators, pinctrl, storage, thermal sensors, USB, SMMU and CPUfreq. On top of this support for the Sony Xperia 10 III is introduced. * tag 'qcom-arm64-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (99 commits) arm64: dts: qcom: sdm630-nile: Correct regulator label name arm64: dts: qcom: sm6125: Improve indentation of multiline properties arm64: dts: qcom: msm8916-longcheer-l8150: Use &pm8916_usbin extcon arm64: dts: qcom: pm8916: Add pm8941-misc extcon for USB detection arm64: dts: qcom: pm8916: Remove wrong reg-names for rtc@6000 arm64: dts: qcom: sc7280: Update Q6V5 MSS node arm64: dts: qcom: sc7280: Add Q6V5 MSS node arm64: dts: qcom: sc7280: Add nodes to boot modem arm64: dts: qcom: sc7280: Add/Delete/Update reserved memory nodes arm64: dts: qcom: sc7280: Update reserved memory map arm64: dts: qcom: msm8998-fxtec-pro1: Add tlmm keyboard keys arm64: dts: qcom: msm8998-fxtec-pro1: Add Goodix GT9286 touchscreen arm64: dts: qcom: msm8998-fxtec-pro1: Add physical keyboard leds arm64: dts: qcom: Add support for MSM8998 F(x)tec Pro1 QX1000 arm64: dts: qcom: msm8916: Fix Secondary MI2S bit clock arm64: dts: qcom: msm8916-longcheer-l8150: Add missing sensor interrupts arm64: dts: qcom: sc7180: Add IMEM and pil info regions arm64: dts: qcom: pm6150l: Add missing include arm64: dts: qcom: sm6350: Add device tree for Sony Xperia 10 III arm64: dts: qcom: sm6350: Add apps_smmu and assign iommus prop to USB1 ... Link: https://lore.kernel.org/r/20211012231155.1036519-1-bjorn.andersson@linaro.orgSigned-off-by:
-
Arnd Bergmann authored
Merge tag 'qcom-dts-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt Qualcomm DTS updates for v5.16 This extends the previous limited description of MSM8226 with SDHC, UART, I2C, SCM, SMEM, RPM and basic PMIC definitions. Based on this, initial support for the LG G Watch R smartwatch is introduced. APQ8064 gets a couple of DT updates, one which will allow the GPU driver to drop supporting legacy "opp tables" in the future. DT bindings and DTS files are updated with additional compatibles, for completeness. * tag 'qcom-dts-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: dt-bindings: arm: qcom, add missing devices ARM: dts: qcom: msm8974: Add xo_board reference clock to DSI0 PHY ARM: dts: qcom: fill secondary compatible for multiple boards ARM: dts: qcom: apq8064: adjust memory node according to specs ARM: dts: qcom: apq8064: Convert adreno from legacy gpu-pwrlevels to opp-v2 ARM: dts: qcom: Add support for LG G Watch R dt-bindings: arm: qcom: Document APQ8026 SoC binding ARM: dts: qcom: Add pm8226 PMIC ARM: dts: qcom: msm8226: Add more SoC bits dt-bindings: arm: qcom: Document SDX65 platform and boards Link: https://lore.kernel.org/r/20211012174310.1017857-1-bjorn.andersson@linaro.orgSigned-off-by:
-
Arnd Bergmann authored
Merge tag 'v5.15-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt Biggest change is, that we have now support for a reset controller inside the mmsys. This goes inhand with changes to the driver, that you will find in the soc pull request. Mediatek PCI device tree binding described the root port in a wrong. The IP actaully implements several root complex with everyone having a single root port. We need to fix the DT in an incompatible way to describe the HW as it is. This also fixes a problem that no IRQ bigger then 32 could be handled. The only public available HW that is affected by this is the BananaPi R64. I'm not aware that there is a big user base using the upstream kernel. In this boards PCI is only used for extension cards, so I don't expect any boot problems. - mt8173: add reset for dsi0 to mmsys - move dt-bindings reset controller includes to correct folder - split PCIe node to use new format for mt2712 and mt7622 - mt8183: add audio node to chromebook devices - mt8192: add clock controller node * tag 'v5.15-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: arm64: dts: mt8183: Add the mmsys reset bit to reset the dsi0 arm64: dts: mt8173: Add the mmsys reset bit to reset the dsi0 dt-bindings: display: mediatek: add dsi reset optional property dt-bindings: mediatek: Add #reset-cells to mmsys system controller arm64: dts: mediatek: Move reset controller constants into common location arm64: dts: mediatek: Split PCIe node for MT2712 and MT7622 arm64: dts: mt8183: add kukui platform audio node arm64: dts: mt8183: add audio node arm64: dts: mediatek: Add mt8192 clock controllers Link: https://lore.kernel.org/r/1a3d63a3-c020-3319-26f6-a2ec338cc42e@gmail.comSigned-off-by:
-
- 15 Oct, 2021 10 commits
-
-
Amelie Delaunay authored
Referring to the note under USBH reset and clocks chapter of RM0436, "In order to access USBH_OHCI registers it is necessary to activate the USB clocks by enabling the PLL controlled by USBPHYC" (ck_usbo_48m). The point is, when USBPHYC PLL is not enabled, OHCI register access freezes the resume from STANDBY. It is the case when dual USBH is enabled, instead of OTG + single USBH. When OTG is probed, as ck_usbo_48m is USBO clock parent, then USBPHYC PLL is enabled and OHCI register access is OK. This patch adds ck_usbo_48m (provided by USBPHYC PLL) as clock of USBH OHCI, thus USBPHYC PLL will be enabled and OHCI register access will be OK. Signed-off-by:
Amelie Delaunay <amelie.delaunay@foss.st.com> Signed-off-by:
Alexandre Torgue <alexandre.torgue@foss.st.com>
-
Olivier Moysan authored
Fix SAI2A and SAI2B pin muxings for AV96 board on STM32MP15. Change sai2a-4 & sai2a-5 to sai2a-2 & sai2a-2. Change sai2a-4 & sai2a-sleep-5 to sai2b-2 & sai2b-sleep-2 Fixes: dcf185ca ("ARM: dts: stm32: Add alternate pinmux for SAI2 pins on stm32mp15") Signed-off-by:
Olivier Moysan <olivier.moysan@foss.st.com> Reviewed-by:
Marek Vasut <marex@denx.de> Signed-off-by:
-
Olivier Moysan authored
The STM32 SAI subblocks registers offsets are in the range 0x0004 (SAIx_CR1) to 0x0020 (SAIx_DR). The corresponding range length is 0x20 instead of 0x1c. Change reg property accordingly. Fixes: 5afd65c3 ("ARM: dts: stm32: add sai support on stm32mp157c") Signed-off-by:
-
Fabrice Gasnier authored
STUSB1600 IRQ (Alert pin) is active low (open drain). Interrupts may get lost currently, so fix the IRQ type. Fixes: 83686162 ("ARM: dts: stm32: add STUSB1600 Type-C using I2C4 on stm32mp15xx-dkx") Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by:
-
Grzegorz Szymaszek authored
The Seeed Odyssey-STM32MP157C board has a 20-pin DVP camera output. The DCMI pins used on this output are defined in the pin state definition &pinctrl/dcmi-1, AKA &dcmi_pins_b (added in mainline commit 02814a41). Set these pins as the default pinctrl of the DCMI peripheral in the board device tree. The pins are not used for any other purpose, so it seems safe to assume most users will not need to override (delete) what this patch provides. status defaults to "disabled", so the peripheral will not be unnecessarily started. And the users who actually intend to make use of a camera on the DVP port will have this little part of the configuration ready. Signed-off-by:
Grzegorz Szymaszek <gszymaszek@short.pl> Reviewed-by:
Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by:
-
Marek Vasut authored
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM, which causes additional signal delay. At 108 MHz, this delay triggers a sporadic issue where the first bit of RX data is not received by the QSPI controller. There are two options of addressing this problem, either by using the DLYB block to compensate the extra delay, or by reducing the QSPI bus clock frequency. The former requires calibration and that is overly complex, so opt for the second option. Fixes: 76045bc4 ("ARM: dts: stm32: Add QSPI NOR on AV96") Signed-off-by:
-
Alexandre Torgue authored
Add support of stm32mp135f discovery board (part number: STM32MP135F-DK). It embeds a STM32MP135F SOC with 512 MB of DDR3. Several connections are available on this board: 4*USB2.0, 1*USB2.0 typeC DRD, SDcard, 2*RJ45, HDMI, Combo Wifi/BT, ... Only SD card, uart4 (console) and watchdog IPs are enabled in this commit. Signed-off-by: -
Alexandre Torgue authored
Add new entry for stm32mp135f-dk board. Signed-off-by:
Rob Herring <robh@kernel.org>
-
Alexandre Torgue authored
Add initial support of STM32MP13 family. The STM32MP13 SoC diversity is composed by: -STM32MP131: -core: 1*CA7, 17*TIMERS, 5*LPTIMERS, DMA/MDMA/DMAMUX -storage: 3*SDMCC, 1*QSPI, FMC -com: USB (OHCI/EHCI, OTG), 5*I2C, 5*SPI/I2S, 8*U(S)ART -audio: 2*SAI -network: 1*ETH(GMAC) -STM32MP133: STM32MP131 + 2*CAN, ETH2(GMAC), ADC1 -STM32MP135: STM32MP133 + DCMIPP, LTDC A second diversity layer exists for security features: -STM32MP13xY, "Y" gives information: -Y = A/D means no cryp IP and no secure boot. -Y = C/F means cryp IP + secure boot. This commit adds basic peripheral. Signed-off-by:
-
Niklas Söderlund authored
There are commits that mess up the encoding of 'ö' in Söderlund, add a correct entry to .mailmap. Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Link: https://lore.kernel.org/r/20211014212906.2331293-1-niklas.soderlund+renesas@ragnatech.seSigned-off-by:
Geert Uytterhoeven <geert+renesas@glider.be>
-
- 14 Oct, 2021 7 commits
-
-
Linus Walleij authored
This force-converts the per-device battery node into the standard properties using "simple-battery" for the HREF machines and the corresponding Samsung battery for the mobile phones. This is fine to do since the battery data in the DTS files has never been deployed or used. In commit a1149ae9 "ARM: ux500: Disable Power Supply and Battery Management by default" it was turned off and has not been switched back on since. In the meantime standardized bindings for batteries have appeared making the old AB8500 battery bindings obsolete. The battery node which is now in the middle of an included file is obviously a per-device piece of information so push this down to each board. The HREF machines all have the same battery and can share a single node in the HREF dtsi file. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org>
-
Geert Uytterhoeven authored
Add operating points for running the Cortex-A57 CPU cores on R-Car H3e-2G, M3e-2G, and M3Ne-2G at 2 GHz. Signed-off-by:
-
Biju Das authored
Enable Ethernet{0,1} interfaces on RZ/G2L SMARC EVK. Signed-off-by:Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20211013075647.32231-3-biju.das.jz@bp.renesas.comSigned-off-by:
-
Biju Das authored
Add Gigabit Ethernet{0,1} nodes to SoC DTSI. Signed-off-by: -
Niklas Söderlund authored
The different port@ entries of the adv7482 nodes shall be encapsulated in a ports node, add one. This change does not change how the driver parses the DT and no driver change is needed. The change however makes it possible to validate the source files with a correct json-schema. Signed-off-by:
-
Niklas Söderlund authored
The V3U have 32 VIN, 4 CSI-2 and 4 ISP nodes that interact with each other for video capture. Add all nodes and record how they are interconnected. Signed-off-by:
-
John Wang authored
Use the 64M layout since the flash on the board is 64M Signed-off-by:
John Wang <wangzhiqiang02@inspur.com> Link: https://lore.kernel.org/r/20211014072743.939293-1-wangzhiqiang02@inspur.comSigned-off-by:
Joel Stanley <joel@jms.id.au>
-
- 12 Oct, 2021 3 commits
-
-
Arnd Bergmann authored
Merge tag 'ti-k3-dt-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux into arm/dt Devicetree changes for TI K3 platforms for v5.16 merge window: * New Platforms: - AM654: Siemens IOT2050 PG2 boards - J721E: Low cost SK board * New features: - mmc aliases introduced - AM64 ICSSG nodes, mcu pinctrl added * Fixes: - Schema fixups for pcie, thermal zones - Fixup to include board specific property for J721e-evm and j7200-evm - Misc fixups including cleaning up order in Makefile * tag 'ti-k3-dt-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux: (24 commits) arm64: dts: ti: k3-j721e-sk: Add DDR carveout memory nodes arm64: dts: ti: k3-j721e-sk: Add IPC sub-mailbox nodes arm64: dts: ti: Add support for J721E SK dt-bindings: arm: ti: Add compatible for J721E SK arm64: dts: ti: iot2050: Add support for product generation 2 boards arm64: dts: ti: iot2050: Prepare for adding 2nd-generation boards dt-bindings: arm: ti: Add bindings for Siemens IOT2050 PG2 boards arm64: dts: ti: iot2050: Add/enabled mailboxes and carve-outs for R5F cores arm64: dts: ti: iot2050: Disable SR2.0-only PRUs arm64: dts: ti: iot2050: Flip mmc device ordering on Advanced devices arm64: dts: ti: k3-j7200-common-proc-board: Add j7200-evm compatible arm64: dts: ti: k3-j721e-common-proc-board: Add j721e-evm compatible dt-bindings: arm: ti: Add missing compatibles for j721e/j7200 evms arm64: dts: ti: Makefile: Collate AM64 platforms together arm64: dts: ti: k3-am64-main: Add ICSSG nodes arm64: dts: ti: k3-am65: Relocate thermal-zones to SoC specific location arm64: dts: ti: ti-k3*: Introduce aliases for mmc nodes arm64: dts: ti: k3-am65-main: Cleanup "ranges" property in "pcie" DT node arm64: dts: ti: j7200-main: Add *max-virtual-functions* for pcie-ep DT node arm64: dts: ti: j7200-main: Fix "bus-range" upto 256 bus number for PCIe ... Link: https://lore.kernel.org/r/20211012120817.beqhp4tygnf3xyi5@wirelessSigned-off-by:
-
Chanho Park authored
SADK(Samsung Automotive Development Kit) is the development kit to evaluate Exynos Auto v9 SoC. It has 16GB LPDDR4 DRAM and two 256GB Samsung UFS. This patch enables only serial console and ufs0 device. Signed-off-by:
Chanho Park <chanho61.park@samsung.com> Link: https://lore.kernel.org/r/20211012002314.38965-4-chanho61.park@samsung.comSigned-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
-
Chanho Park authored
Add minimal support for ExynosAuto v9 SoC[1]. - Enumarate all pinctrl nodes - UART with exynos850 compatible - UFS0 HCI + Phy Like exynos850, this also uses fixed-rate clock nodes until clock driver has been supported. The clock nodes are initialized on bootloader stage thus we don't need to control them so far. [1]: https://www.samsung.com/semiconductor/minisite/exynos/products/automotiveprocessor/exynos-auto-v9/Signed-off-by:
-
- 11 Oct, 2021 8 commits
-
-
Oskar Senft authored
The TYAN S7106 is a server platform with an ASPEED AST2500 BMC. Signed-off-by:
Oskar Senft <osk@google.com> Reviewed-by:
Jeremy Kerr <jk@codeconstruct.com.au> Reviewed-by:
-
Adriana Kobylak authored
Add the power-config-full-load described in: https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md#power-config-full-load The power-config-full-load gpio is designed to be used to specify how many power supplies the system should have, in rainier it is 2 or 4. If enough power supplies fail so that the system no longer has redundancy (no longer n+1), the hardware will signal to the Onboard Chip Controller that the system may be oversubscribed, and performance may need to be reduced so the system can maintain it's powered on state. Signed-off-by:
Adriana Kobylak <anoo@us.ibm.com> Reviewed-by:
Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20211005192226.213539-1-anoo@linux.ibm.comSigned-off-by:
-
Arnd Bergmann authored
Merge tag 'tegra-for-5.16-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt ARM: tegra: Device tree changes for v5.16-rc1 This contains various cleanup patches to 32-bit ARM Tegra device trees and enables USB OTG mode on the Nexus 7. * tag 'tegra-for-5.16-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: ARM: tegra: Remove useless usb-ehci compatible string ARM: tegra: Remove unused backlight-boot-off property ARM: tegra: nexus7: Enable USB OTG mode ARM: tegra: Add new properties to USB PHY device-tree nodes ARM: tegra: Update Broadcom Bluetooth device-tree nodes ARM: tegra: acer-a500: Correct compatible of ak8975 magnetometer Link: https://lore.kernel.org/r/20211008201132.1678814-6-thierry.reding@gmail.comSigned-off-by:
-
Arnd Bergmann authored
The patch uses the "dt-bindings/clock/sprd,ums512-clk.h header, which is not merged yet. This caused a build regression, and it means the patch was not ready to get merged anyway. This reverts commit 23410de5. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linuxArnd Bergmann authored
AT91 DT #1 for 5.16: - Addition of a new variant in the sama5d2 family: the sama5d29 with significant updates being CAN and Ethernet controllers; - Add support for Exegin Q5xR5 and CalAmp LMU5000 boards which were maintained up to this moment, separately, in OpenWrt tree; - Two more boards gained I2C bus recovery support; - Tse850 updated with one Ethernet fix; - Sama7g5ek gained ADC nodes and sama5d27_wlsom1 WiFi support. * tag 'at91-dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: ARM: at91: dts: sama5d29: Add dtsi file for sama5d29 ARM: dts: at91-sama5d2_icp.dts: Added I2C bus recovery support ARM: dts: at91: tse850: the emac<->phy interface is rmii ARM: dts: at91: add Exegin Q5xR5 board dt-bindings: ARM: at91: document exegin q5xr5 board dt-bindings: add vendor prefix for exegin ARM: dts: at91: add CalAmp LMU5000 board dt-bindings: ARM: at91: document CalAmp LMU5000 board dt-bindings: add vendor prefix for calamp ARM: dts: at91: at91sam9260: add pinctrl label ARM: dts: at91-sama5d27_som1_ek: Added I2C bus recovery support ARM: dts: at91: sama7g5ek: enable ADC on the board ARM: dts: at91: sama7g5: add node for the ADC ARM: dts: at91: sama5d27_wlsom1: add wifi device Link: https://lore.kernel.org/r/20211011123438.16562-1-nicolas.ferre@microchip.comSigned-off-by:
-
Arnd Bergmann authored
Merge tag 'omap-for-v5.16/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt Devicetree changes for omaps for v5.16 These changes configure devices for am335x and dra7, and fixes various devicetree check warnings for gta04: - Update am335x-pocketbeagle to use pinconf-single - A series of devicetree warning fixes for omap3 and gta04 - Configure bb2d Vivante GC 2D Accelerator for dra7 * tag 'omap-for-v5.16/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: dra7: add entry for bb2d module arm: dts: omap3-gta04: cleanup led node names arm: dts: omap3-gta04a4: accelerometer irq fix arm: dts: omap3-gta04a5: fix missing sensor supply arm: dts: omap3-gta04: fix missing sensor supply arm: dts: omap3-gta04: cleanup LCD definition ARM: dts: omap3: fix cpu thermal label name ARM: dts: am335x-pocketbeagle: switch to pinconf-single Link: https://lore.kernel.org/r/pull-1633950030-501948@atomide.com-3Signed-off-by:
-
Arnd Bergmann authored
Merge tag 'v5.15-next-dts32' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt mt7623: add USB nodes mt7629: update PCIe node to new format * tag 'v5.15-next-dts32' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: dt-bindings: arm: Add MT6589 Fairphone 1 ARM: dts: mediatek: Update MT7629 PCIe node for new format arm: dts: mt7623: add otg nodes for bpi-r2 arm: dts: mt7623: add musb device nodes Link: https://lore.kernel.org/r/7135d46f-5fb9-b46d-96d4-3b38548fe23e@gmail.comSigned-off-by:
-
Arnd Bergmann authored
Merge tag 'tegra-for-5.16-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt arm64: tegra: Device tree changes for v5.16-rc1 This enables additional interrupts on the Tegra194 GPIO controller for better load balancing and/or virtualization, adds audio support on Jetson TX2 NX, enables the NVDEC video decoder on Tegra186 and later and enables more audio processors that are found on Tegra210 and later. Various cleanups across the board top things off. * tag 'tegra-for-5.16-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: arm64: tegra: Fix pcie-ep DT nodes arm64: tegra: Remove useless usb-ehci compatible string arm64: tegra: Extend APE audio support on Jetson platforms arm64: tegra: Add few AHUB devices for Tegra210 and later arm64: tegra: Remove unused backlight-boot-off property arm64: tegra: Add NVDEC to Tegra186/194 device trees arm64: tegra: Add new USB PHY properties on Tegra132 arm64: tegra: Update HDA card name on Jetson TX2 NX arm64: tegra: Audio graph sound card for Jetson TX2 NX arm64: tegra: Add additional GPIO interrupt entries on Tegra194 Link: https://lore.kernel.org/r/20211008201132.1678814-7-thierry.reding@gmail.comSigned-off-by:
-
