- 09 Feb, 2021 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linuxArnd Bergmann authored
Samsung DTS ARM changes for v5.12 1. Use new compatile to properly configure Exynos5420 USB2 PHY, fixing it suspend/resume cycle. 2. Correct Samsung PMIC interrupt trigger levels on multiple boards. 3. Correct the voltages of Samsung GT-I9100 charger and add top-off charger. * tag 'samsung-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: ARM: dts: exynos: Add top-off charging regulator node for I9100 ARM: dts: exynos: Fix charging regulator voltage and current for I9100 ARM: dts: exynos: correct PMIC interrupt trigger level on Odroid XU3 family ARM: dts: exynos: correct PMIC interrupt trigger level on Arndale Octa ARM: dts: exynos: correct PMIC interrupt trigger level on Spring ARM: dts: exynos: correct PMIC interrupt trigger level on Rinato ARM: dts: exynos: correct PMIC interrupt trigger level on Monk ARM: dts: exynos: correct PMIC interrupt trigger level on Artik 5 ARM: dts: exynos: use Exynos5420 dedicated USB2 PHY compatible Link: https://lore.kernel.org/r/20210125191240.11278-3-krzk@kernel.orgSigned-off-by:
Arnd Bergmann <arnd@arndb.de>
-
- 02 Feb, 2021 21 commits
-
-
Lubomir Rintel authored
A copy & paste oversight from MMP2; camera interrupts are handled via a multiplexer on MMP3. Signed-off-by:
Lubomir Rintel <lkundrak@v3.sk> Link: https://lore.kernel.org/r/20210121034130.1381872-13-lkundrak@v3.sk' Signed-off-by:
-
Lubomir Rintel authored
The firmware leaves the pins in GPIO mode. Until we have a proper pinmux driver hooked on we just need to bitbang SPI. No big deal, this is just used for the power button and performance is not important. Signed-off-by:
-
Lubomir Rintel authored
This adds support for the power button attached to the Embedded Controller on a Dell Wyse 3020 "Ariel" board. However, while the EC itself is controlled via I2C, the input capability for the power button acts as a separate device attached to the SPI, hence it has a separate device node. Signed-off-by:
-
Lubomir Rintel authored
Add the device node for the computer's embedded controller, responsible for controlling the LEDs and system power. Signed-off-by:
-
Lubomir Rintel authored
These are slighly easier to read. Signed-off-by:
-
Lubomir Rintel authored
These are slighly easier to read. Signed-off-by:
-
Lubomir Rintel authored
The ACGR register is at the offset of 0x1024, beyond the 4k originally assigned to the MPMU range. Signed-off-by:
-
Lubomir Rintel authored
Drop the linux,usable-memory properties; the schema is unhappy about them. They've been cargo-culted from Open Firmware and I don't know what purpose they serve. Perhaps they are meant to provide the OFW runtime. In that case it's still okay to drop them from here; OFW is welcome to add it upon boot. Signed-off-by:
-
Lubomir Rintel authored
Drop the linux,usable-memory properties; the schema is unhappy about them: mmp2-olpc-xo-1-75.dt.yaml: /: memory: False schema does not allow {'linux,usable-memory': [[0, 528482304]], 'available': [[847872, 519245824, 4096, 782336]], 'reg': [[0, 536870912]], 'device_type': ['memory']} They've been cargo-culted from Open Firmware and I don't know what purpose they serve. Perhaps they are meant to provide the OFW runtime. In that case it's still okay to drop them from here; OFW is welcome to add it upon boot. Signed-off-by: -
Lubomir Rintel authored
It contains a reg property. Add its base to the node name. Signed-off-by:
-
Lubomir Rintel authored
On MMP3 the camera interface is on a separate power island. This property tells the driver to enable it when appropriate. Signed-off-by:
-
Lubomir Rintel authored
The property specifies a list of GPIO-capable pins. Don't limit it to a single element as there's presumably more than one GPIO pin. Signed-off-by:
-
Arnd Bergmann authored
Merge tag 'mvebu-dt64-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt mvebu dt64 for 5.12 (part 1) - rename u-boot mtd partition to a53-firmware on Turris Mox (Armada 3720 based) - improve SDHCI support on AP807 based board - move SATA comphy into main armada-37xx.dtsi - add Armada 8K/7K PWM support * tag 'mvebu-dt64-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu: arm64: dts: armada: add pwm offsets for ap/cp gpios arm64: dts: marvell: armada-37xx: Add SATA comphy into main armada-37xx.dtsi file arm64: dts: cn913x-db: enable MMC HS400 arm64: dts: change AP807 SDHCI compatibility string arm64: dts: armada-3720-turris-mox: rename u-boot mtd partition to a53-firmware Link: https://lore.kernel.org/r/87pn1jn48s.fsf@BL-laptopSigned-off-by:
-
Arnd Bergmann authored
Merge tag 'mvebu-dt-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt mvebu dt for 5.12 (part 1) Improve LED and fan support on Helios4 boad (Armada 388 based) Add ECC configuration for Linksys board (Aramda 385 based) * tag 'mvebu-dt-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu: ARM: dts: armada388-helios4: assign pinctrl to each fan ARM: dts: armada388-helios4: assign pinctrl to LEDs ARM: dts: armada-385-linksys: fix usage with newer devices Link: https://lore.kernel.org/r/87sg6fn49o.fsf@BL-laptopSigned-off-by:
-
Arnd Bergmann authored
Merge tag 'v5.11-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt mt6779: - add DEVAPC node to detect mallicious bus accesses - add PMIC wrapper node mt7622: - add reset to mmc node mt8183: - fix typo in drma-fifo-size property - refine compatible for the disp-gamma - add phandel of PM domain to the PWM node - add second PWM node - add regulator to MFG power domain - enable DSI node in kukui - add krane sku0, which uses different panel - fix mailbox dt-bindings include path mt8192: - add NOR flash node - add PSCI based CPU idle states mt8516: - add node for the UART's APDMA controller * tag 'v5.11-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: arm64: dts: mt8183: Fix GCE include path dts64: mt7622: fix slow sd card access dt-bindings: arm64: dts: mediatek: Add krane sku0 arm64: dts: mt8183: Add krane-sku0 board. arm64: dts: mt8183: config dsi node arm64: dts: mt6779: Support pwrap on Mediatek MT6779 platform arm64: dts: mt6779: Support devapc arm64: dts: mt8192: Add cpu-idle-states arm64: dts: mediatek: mt8183: Add domain supply for mfg arm64: dts: mt8192: add nor_flash device node arm64: dts: mediatek: mt8516: add support for APDMA arm64: dts: mediatek: mt8183-evb: add PWM support arm64: dts: mediatek: mt8183: add pwm node arm64: dts: mt8183: Add missing power-domain for pwm0 node arm64: dts: mt8183: refine gamma compatible name arm64: dts: mt8183: rename rdma fifo size Link: https://lore.kernel.org/r/565be0cc-460a-7d0b-47da-09bf0401e8fe@gmail.comSigned-off-by:
-
Linus Walleij authored
This adds the Richtek RT8515 Flash LED to the Golden, Skomer and Janice device trees. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20210201091308.284465-1-linus.walleij@linaro.org' Signed-off-by:
-
Arnd Bergmann authored
Merge tag 'keystone_dts_for_5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into arm/dt ARM: DTS: Keystone update for v5.12 Contains couple updates for DWC USB3 DT nodes * tag 'keystone_dts_for_5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: arm: dts: keystone: Harmonize DWC USB3 DT nodes name arm: dts: keystone: Correct DWC USB3 compatible string Link: https://lore.kernel.org/r/1612156910-11159-1-git-send-email-santosh.shilimkar@oracle.comSigned-off-by:
-
https://github.com/Broadcom/stblinuxArnd Bergmann authored
This pull request contains Broadcom ARM64-based SoCs Device Tree changes for 5.12 please pull the following: - Rafal continues to add support for the 4906/4908 SoC family and adds a Device Tree for the Netgear R8000P router (4906-based), describes the NAND controller of the 4908 more appropriately (based on the older 63138 DSL SoC), describes the 4908 PCIe reset controller, internal Ethernet switch (Starfighter 2 switch) and finally the Power Management Bus (PMB) - Scott removes all of the SATA-related Device Tree nodes since SATA is unused on the Stingray product line * tag 'arm-soc/for-5.12/devicetree-arm64' of https://github.com/Broadcom/stblinux: arm64: dts: broadcom: Remove SATA from Stingray arm64: dts: broadcom: bcm4908: describe PMB block arm64: dts: broadcom: bcm4908: describe internal switch arm64: dts: broadcom: bcm4908: describe PCIe reset controller arm64: dts: broadcom: bcm4908: use proper NAND binding arm64: dts: broadcom: bcm4908: add BCM4906 Netgear R8000P DTS files dt-bindings: arm: bcm: document Netgear R8000P binding Link: https://lore.kernel.org/r/20210131221721.685974-4-f.fainelli@gmail.comSigned-off-by:
-
https://github.com/Broadcom/stblinuxArnd Bergmann authored
This pull request contains Broadcom ARM-based SoCs Device Tree changes for 5.12, please pull the following: - Dave adds a proper compatile string for the DSI1 panel on 2711 (Raspberry Pi 4) to permit adequate driver differentiation - Nicolas declares reserved memory regions filed by the Rasbperry Pi bootloader to indicate the running system configuration - Maxime declares the BSC (HDMI I2C controller) and CEC interrupt controllers - Stanislav fixes a tab vs. space issue in the BCM21664 DTS * tag 'arm-soc/for-5.12/devicetree' of https://github.com/Broadcom/stblinux: ARM: dts: bcm2711: Add the CEC interrupt controller ARM: dts: bcm21664: Replace spaces with a tab ARM: dts: bcm2711: Add the BSC interrupt controller ARM: dts: bcm2711: Add reserved memory template to hold firmware configuration ARM: dts: bcm2711: Use compatible string for BCM2711 DSI1 Link: https://lore.kernel.org/r/20210131221721.685974-3-f.fainelli@gmail.comSigned-off-by:
-
Arnd Bergmann authored
Merge tag 'sunxi-dt-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt Our usual bunch of patches to support the Allwinner SoCs, this time adding: - DT fixes spotted through the schemas - Mali Support for the A10s/A13/GR8/R8 - MMC improvements for the A64 and H6 - New board: SL631 Action Camera, PineTab Early Adopter * tag 'sunxi-dt-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (47 commits) ARM: dts: sunxi: Rename nmi_intc to r_intc ARM: dts: sun8i: h2-plus: bananapi-m2-zero: Increase BT UART speed ARM: dts: sunxi: bananapi-m2-plus: Increase BT UART speed arm64: dts: allwinner: pine-h64: Fix typos in BT GPIOs arm64: dts: allwinner: pinetab: Fix the panel compatible arm64: dts: allwinner: pinephone: Remove useless light sensor supplies arm64: dts: allwinner: h6: Use - instead of @ for DT OPP entries ARM: dts: sun8i-a33: sina33: Add missing panel power supply ARM: dts: sun8i-a83t: Remove empty CSI port ARM: dts: sun8i-s3: pinecube: Fix CSI DTC warnings ARM: dts: sun8i-s3: impetus: Fix the USB PHY ID detect GPIO properties ARM: dts: sun8i: nanopi-r1: Fix GPIO regulator state array ARM: dts: sun6i: primo81: Remove useless io-channel-cells ARM: dts: sunxi: Fix CPU thermal zone node name ARM: dts: sunxi: Add missing backlight supply ARM: dts: sunxi: Fix the LED node names dt-bindings: rtc: sun6i-a31-rtc: Loosen the requirements on the clocks dt-bindings: iio: adc: Add AXP803 compatible dt-bindings: sunxi: Fix the pinecube compatible ARM: dts: sun8i-v3s: Add CSI0 MCLK pin definition ... Link: https://lore.kernel.org/r/48511540-fdd6-4fbe-8037-ec9fa8436147.lettre@localhostSigned-off-by:
-
Arnd Bergmann authored
Merge tag 'ti-k3-dt-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux into arm/dt Devicetree changes for TI K3 platforms for v5.12 merge window: - Common fixups: PMU compatible, MMC dtbs_check warnings squelch - J7200: R5F, PCIe, SERDES support - J721E: PCIE fixups * tag 'ti-k3-dt-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux: arm64: dts: ti: k3*: Fixup PMU compatibility to be CPU specific arm64: dts: ti: k3: mmc: fix dtbs_check warnings arm64: dts: ti: k3-j7200-som-p0: Add DDR carveout memory nodes for R5Fs arm64: dts: ti: k3-j7200-som-p0: Add mailboxes to R5Fs arm64: dts: ti: k3-j7200: Add R5F cluster nodes arm64: dts: ti: k3-j7200-common-proc-board: Enable PCIe arm64: dts: ti: k3-j7200-common-proc-board: Enable SERDES0 arm64: dts: ti: k3-j7200-main: Add PCIe device tree node arm64: dts: ti: k3-j7200-main: Add SERDES and WIZ device tree node arm64: dts: ti: k3-j721e-main: Remove "syscon" nodes added for pcieX_ctrl arm64: dts: ti: k3-j721e-main: Fix supported max outbound regions Link: https://lore.kernel.org/r/20210130131422.yvq2edxfongys7x5@pendantSigned-off-by:
-
- 01 Feb, 2021 1 commit
-
-
Matthias Brugger authored
The header file of GCE should be for MT8183 SoC instead of MT8173. Fixes: 91f9c963 ("arm64: dts: mt8183: Add display nodes for MT8183") Reported-by:
CK Hu <ck.hu@mediatek.com> Signed-off-by:
Matthias Brugger <mbrugger@suse.com> Reviewed-by:
Chun-Kuang Hu <chunkuang.hu@kernel.org> Link: https://lore.kernel.org/r/20210131101726.804-1-matthias.bgg@kernel.orgSigned-off-by:
Matthias Brugger <matthias.bgg@gmail.com>
-
- 31 Jan, 2021 17 commits
-
-
Samuel Holland authored
The R_INTC block controls more than just the NMI, and it is a different hardware block than the NMI INTC found in some other Allwinner SoCs, so the label "nmi_intc" is inaccurate. Name it "r_intc" to match the compatible and to match the few references in the vendor documentation. Signed-off-by:
Samuel Holland <samuel@sholland.org> Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20210118055040.21910-6-samuel@sholland.org
-
Jernej Skrabec authored
Bluetooth module on BananaPi M2 Zero can also be used for streaming audio. However, for that case higher UART speed is required. Add a max-speed property. Signed-off-by:
Jernej Skrabec <jernej.skrabec@siol.net> Acked-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
-
Jernej Skrabec authored
Bluetooth module on BananaPi M2 Plus can also be used for streaming audio. However, for that case higher UART speed is required. Add a max-speed property. Signed-off-by:
-
Maxime Ripard authored
The commit 53441b8e ("arm64: dts: allwinner: h6: PineH64 model B: Add bluetooth") introduced the Bluetooth chip for the PineH64 model B, but the GPIOs property didn't conform to the binding of the bluetooth chip. Let's fix this. Fixes: 53441b8e ("arm64: dts: allwinner: h6: PineH64 model B: Add bluetooth") Signed-off-by:
-
Maxime Ripard authored
The commit 7fa40ca7 ("arm64: allwinner: dts: a64: add DT for Early Adopter's PineTab") introduced an ili9881-based panel device node but didn't conform to the binding. Fix this. Fixes: 7fa40ca7 ("arm64: allwinner: dts: a64: add DT for Early Adopter's PineTab") Signed-off-by:
-
Maxime Ripard authored
The stk3311 binding don't expect a vdd or leda power supplies. Remove them. Signed-off-by:
-
Maxime Ripard authored
DTC and the dt-validate tools report warnings for opp with the format opp@$frequency: dtc for a missing reg property, and dt-validate since the binding requires child nodes to have the format opp-$frequency. Change this to the latter format. Signed-off-by:
-
Maxime Ripard authored
The SinA33 panel is missing its power-supply property, even though the binding mandates it. Signed-off-by:
-
Maxime Ripard authored
The empty CSI port triggers a dt-validate warning. Let's align with the other DTSI and remove it entirely, expecting the DTS to fill it. Signed-off-by:
-
Maxime Ripard authored
Our CSI endpoint trigger some DTC warnings due to the fact that we're having a single endpoint that doesn't need any reg property, and since we don't have a reg property, we don't need the address-cells and size-cells properties anymore. Fix those Signed-off-by:
-
Maxime Ripard authored
While the USB PHY Device Tree mandates that the name of the ID detect pin should be usb0_id_det-gpios, a significant number of device tree use usb0_id_det-gpio instead. This was functional because the GPIO framework falls back to the gpio suffix that is legacy, but we should fix this. Signed-off-by:
-
Maxime Ripard authored
Even though it translates to the same thing down to the binary level, we should have an array of 2 number cells to describe each voltage state, which in turns create a validation warning. Let's fix this. Signed-off-by:
-
Maxime Ripard authored
The mma8452 binding doesn't expect an io-channel-cells property, let's remove it. Signed-off-by:
-
Frank Wunderlich authored
Fix extreme slow speed (200MB takes ~20 min) on writing sdcard on bananapi-r64 by adding reset-control for mmc1 like it's done for mmc0/emmc. Fixes: 2c002a30 ("arm64: dts: mt7622: add mmc related device nodes") Signed-off-by:
Frank Wunderlich <frank-w@public-files.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210113180919.49523-1-linux@fw-web.deSigned-off-by:
-
Hsin-Yi Wang authored
Krane-sku0 is similar to krane-sku176 but using a different panel source. Signed-off-by:
Hsin-Yi Wang <hsinyi@chromium.org> Reviewed-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Enric Balletbo i Serra <enric.balletbo@collabora.com> Link: https://lore.kernel.org/r/20210113110400.616319-3-hsinyi@chromium.orgSigned-off-by:
-
Hsin-Yi Wang authored
Similar to krane-sku176 but using a different panel source. Signed-off-by:
-
Hsin-Yi Wang authored
Config dsi node for mt8183 kukui. Set panel and ports. Several kukui boards share the same panel property and only compatible is different. So compatible will be set in board dts for comparison convenience. Signed-off-by:
Nicolas Boichat <drinkcat@chromium.org> Link: https://lore.kernel.org/r/20210113110400.616319-1-hsinyi@chromium.orgSigned-off-by:
-
