Merge tag 'sunxi-dt64-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Allwinner arm64 DT changes for 4.20

Our usual set of DT changes for the arm64 Allwinner SoCs.

The most notable things are:
  - HDMI support on the A64
  - New boards: OrangePi One Plus

* tag 'sunxi-dt64-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (28 commits)
  arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
  arm64: dts: allwinner: a64: Enable HDMI output on A64 boards w/ HDMI
  arm64: dts: allwinner: a64: Add display pipeline
  arm64: dts: allwinner: h6: add system controller device tree node
  arm64: dts: allwinner: h6: Add OrangePi One Plus initial support
  arm64: dts: allwinner: a64: Rename r_i2c_pins_a label to r_i2c_pl89_pins
  arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins
  arm64: dts: allwinner: a64: Split out data strobe pin from mmc2 pinmux
  arm64: dts: allwinner: a64: NanoPi-A64: Add blue status LED
  arm64: dts: allwinner: a64: NanoPi-A64: Add Wifi chip
  arm64: dts: allwinner: a64: NanoPi-A64: Add Ethernet
  arm64: dts: allwinner: a64: NanoPi-A64: Fix DCDC1 voltage
  arm64: dts: allwinner: a64: Olinuxino: enable USB
  arm64: dts: allwinner: a64: Olinuxino: add Ethernet nodes
  arm64: dts: allwinner: a64: Olinuxino: fix DRAM voltage
  arm64: dts: allwinner: a64: Orange Pi Win: Adjust CSI power rails
  arm64: dts: allwinner: a64: Orange Pi Win: Add SPI flash node
  arm64: dts: allwinner: a64: Orange Pi Win: Add SDIO node
  arm64: dts: allwinner: a64: Orange Pi Win: Add LED node
  arm64: dts: allwinner: a64: Orange Pi Win: Add UARTs
  ...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'sunxi-dt-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Allwinner DT changes for 4.20

Our usual bunch of DT patches for the Allwinner arm32 SoCs.

The most notable changes are:
  - Support for the video decoding / encoding engine on the
    A10s/A13/A20/A33
  - IR support for the A83t
  - SATA support for the R40

* tag 'sunxi-dt-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun9i: Fix I2C bus warnings
  ARM: dts: sunxi: Fix I2C bus warnings
  ARM: dts: sun8i-a33: Add Video Engine and reserved memory nodes
  ARM: dts: sun7i-a20: Add Video Engine and reserved memory nodes
  ARM: dts: sun5i: Add Video Engine and reserved memory nodes
  ARM: dts: sun8i: sun8i-r40-bananapi-m2-ultra: enable AHCI
  ARM: dts: sun8i: r40: add sata node
  ARM: dts: sunxi: Don't use cd-inverted in sun8i-r40-bananapi-m2-ultra
  ARM: dts: sun8i: a83t: bananapi-m3: Enable IR controller
  ARM: dts: sun8i: a83t: Add support for the cir interface
  ARM: dts: sun8i: a83t: Add the cir pin for the A83T
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'sunxi-h3-h5-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Allwinner H3 and H5 DT additions for 4.20

This is our usual H3/H5 pull request

The most notable changes are:
  - the video decoding / encoding unit is finally enabled on the H3
  - Mali support for the H5
  - New boards: BananaPi M2+ v1.2, Orange Pi Zero Plus 2 H3 support

* tag 'sunxi-h3-h5-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees
  ARM: dts: sun8i-h3: Add Video Engine and reserved memory nodes
  arm64: dts: allwinner: h5: Add device tree for Bananapi M2 Plus H5
  ARM: dts: sun8i: h3: Split out non-SoC-specific parts of Bananapi M2 Plus
  ARM: dts: sun8i: h3: bpi-m2-plus: Fix address for external RGMII Ethernet PHY
  ARM: dts: sun8i: h3-h5: ir register size should be the whole memory block
  arm64: dts: allwinner: h5: Add device node for Mali-450 GPU
  ARM: dts: sun8i: Add initial Orangepi Zero Plus 2 H3 support
  nvmem: sunxi-sid: add support for H5's SID controller
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Bananapi released an updated revision of the H3/H5 based Bananapi M2+.
Version 1.2 enables voltage control for the CPU's regulator by using
a GPIO line to toggle a MOSFET that can change the effective resistance
value in the regulator's feedback network.

This patch adds a common .dtsi file for this new revision, which
includes the original common sunxi-bananapi-m2-plus.dtsi file, and
adds the GPIO-controlled regulator and a cpu-supply reference. H3
and H5 variant dts files are added as well.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

This adds nodes for the Video Engine and the associated reserved memory
for the H3. Up to 96 MiB of memory are dedicated to the CMA pool.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

The Bananapi M2 Plus H5 is a variant of the original Bananapi M2 Plus,
with the H3 SoC replaced with an H5. Everything else is the same.

Add a stub device tree incorporating the shared bananapi-m2-plus dtsi
file.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

Three more variants of the Bananapi M2 Plus have been introduced. One
with the H5 instead of the H3, another with the H2+ instead, and the
last with the H3 but with WiFi and eMMC removed.

All these variants use the same board. This patch splits out the
non-SoC-specific parts of the device tree, so that they can be shared
among all the variants. The original Bananapi M2 Plus has been renamed
to Bananapi M2 Plus H3.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The external RTL8211E RGMII Ethernet PHY is configured via external
resistors to use the address 0x1. The 0x0 address is a broadcast address
for this family of PHYs, and should not be used explicitly.

Fixes: 8c7ba536 ("ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i")
Fixes: 4904337f ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The size of the register should be the size of the whole memory block,
not just the registers, that are needed.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The H5 has a Mali-450 GPU with 4 Pixel Processor cores.

Interestingly, while the datasheet lists an interrupt line for the GPU's
PMU, the hardware block itself doesn't seem to have it. Reads from the
PMU address range all return zero, and writes are ignored.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Orangepi Zero Plus 2 is an open-source single-board computer, available in two
Allwinner SOC variants, H3 and H5. We add support for H3 variant here, as the
H5 is already supported by sun50i-h5-orangepi-zero-plus2.dts.

H3 Orangepi Zero Plus 2 has:
- Quad-core Cortex-A7
- 512MB DDR3
- microSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG + power supply
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

The H5 SoC have a SID controller that looks like the one in A64, the
cells are in the same offset but doesn't contain the same data (thermal
sensor calibration for example).
Add a binding for it.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Merge tag 'renesas-dt-bindings-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Renesas ARM Based SoC DT Bindings Updates for v4.20

* Document bindings for:
  - RZ/G2E (r8a774c0), RZ/G2M (r8a774a1) and RZ/A2 (r7s9210) SoCs
  - R-Car M3-N (r8a77965) SoC based ULCB board

* tag 'renesas-dt-bindings-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  dt-bindings: arm: Document RZ/G2E SoC DT bindings
  dt-bindings: arm: Document Renesas R-Car M3-N-based ULCB board
  dt-bindings: arm: Document RZ/A2 SoC DT bindings
  dt-bindings: arm: Document RZ/G2M SoC DT bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-arm-dt2-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Second Round of Renesas ARM Based SoC DT Updates for v4.20

* RZ/G1M (r8a7743) based iWave G20D-Q7 board and camera daughter board
  - Move PCIe node out of common dtsi to allow reuse of the common dtsi
    on the iWave RZ/G1N board
* RZ/G1C (r8a77470) SoC: Add I2C4, SDHI2 and SMP support
* R-Car Gen1 based boards and R-Car Gen2 SoCs:
  - Enhance top-of-file comments to include SoC name
* RZ/N1D (r9a06g032) SoC:
  - Correct UART0 description and add all other UARTs

* tag 'renesas-arm-dt2-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: dts: iwg20d-q7-common: Move pciec node out of common dtsi
  ARM: dts: r8a77470: Add I2C4 support
  ARM: dts: r8a77470: Add SDHI2 support
  ARM: dts: r8a77470: Add SMP support
  ARM: dts: R-Car Gen1 board comment update
  ARM: dts: Include R-Car Gen2 product name in DTSI files
  ARM: dts: r9a06g032: Correct UART and add all other UARTs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-arm64-dt2-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Second Round of Renesas ARM64 Based SoC DT Updates for v4.20

* Remove unneeded status from thermal nodes

* R-Car Gen 3 SoCs:
  - Use 400kHz for I2C DVFS bus
  - Revise USB2.0 properties
* R-Car Gen 3 SoC based ULCB boards: Add default bootargs
* R-Car M3-N (r8a77965) SoC based boards: Enable audio with DMA

* R-Car V3M (r8a77970 and V3H (r8a77980) SoCs:
  - Add compare match timer (CMT) support
  - Add timer pulse unit (TPU) support
* R-Car V3H (r8a77980) and E3 (r8a77990) SoCs:
  - Attach the SYS-DMAC to the IPMMU
* E3 (r8a77990) SoC: Add display output support
* R-Car E3 (r8a77990) based Ebisu board:
  - Enable HDMI and CVBS input, and VGA and HDMI display output

* R-Car D3 (r8a77995) SoC: Add LVDS support
* R-Car D3 (r8a77995) based Draak board: Enable HDMI display output

* tag 'renesas-arm64-dt2-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  arm64: dts: renesas: r8a77965: Add Sound and Audio DMAC device nodes
  arm64: dts: renesas: r8a77995: draak: Enable HDMI display output
  arm64: dts: renesas: r8a77990: ebisu: Enable VGA and HDMI outputs
  arm64: dts: renesas: r8a77995: Add LVDS support
  arm64: dts: renesas: r8a77990: Add display output support
  arm64: dts: renesas: r8a779{7|8}0: add TPU support
  arm64: dts: renesas: revise properties for R-Car Gen3 SoCs' usb 2.0
  arm64: dts: renesas: ulcb: add default bootargs
  arm64: dts: renesas: r8a779{7|8}0: add CMT support
  arm64: dts: renesas: gen3: use 400kHz for I2C DVFS bus
  arm64: dts: renesas: r8a77980: Attach the SYS-DMAC to the IPMMU
  arm64: dts: renesas: r8a77990: Attach the SYS-DMAC to the IPMMU
  arm64: dts: renesas: ebisu: Add HDMI and CVBS input
  arm64: dts: renesas: Remove unneeded status from thermal nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'tegra-for-4.20-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

arm64: tegra: Device tree changes for v4.20-rc1

This contains mostly device tree changes to support faster SDHCI modes
on Tegra210 and Tegra186.

* tag 'tegra-for-4.20-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  arm64: tegra: I2C on Tegra194 is not compatible with Tegra114
  arm64: dts: tegra186: Enable HS400
  arm64: dts: tegra210: Enable HS400
  arm64: dts: tegra186: Add SDMMC4 DQS trim value
  arm64: dts: tegra210: Add SDMMC4 DQS trim value
  arm64: dts: tegra186: Assign clocks for sdmmc1 and sdmmc4
  arm64: dts: tegra210: Assign clocks for sdmmc1 and sdmmc4
  arm64: dts: tegra186: Add SDHCI tap and trim values
  arm64: dts: tegra210: Add SDHCI tap and trim values
  arm64: dts: tegra186: Add sdmmc pad auto calibration offsets
  arm64: dts: tegra210: Add sdmmc pad auto calibration offsets
  arm64: dts: tegra210-p2597: Remove no-1-8-v from sdmmc1
  arm64: dts: tegra210-p2180: Correct sdmmc4 vqmmc-supply
  arm64: dts: tegra210-p2180: Allow ldo2 to go down to 1.8 V
  arm64: dts: Add Tegra186 sdmmc pinctrl voltage states
  arm64: dts: Add Tegra210 sdmmc pinctrl voltage states
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'tegra-for-4.20-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

ARM: tegra: Device tree changes for v4.20-rc1

This contains a massive amount of changes from Marcel Ziswiler for
various boards by Toradex.

* tag 'tegra-for-4.20-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (129 commits)
  ARM: dts: paz00: fix wakeup gpio keycode
  ARM: tegra: tegra20: Fix mixed tabs-spaces indentation
  ARM: tegra: colibri_t20: add eval board device tree
  ARM: tegra: colibri_t20: rename ac97 label to tegra_ac97
  ARM: tegra: colibri_t20: get rid of fake clocks simple bus
  ARM: tegra: colibri_t20: rename tps6586x@34 and drop unused pmic label
  ARM: tegra: colibri_t20: iris: drop unused i2c_ddc label
  ARM: tegra: colibri_t20: rename i2c_ddc to hdmi_ddc
  ARM: tegra: colibri_t20: drop module level model and compatible
  ARM: tegra: colibri_t20: iris: add colibri ssp support
  ARM: tegra: colibri_t20: iris: simplify model and compatible properties
  ARM: tegra: colibri_t20: simplify model and compatible properties
  ARM: tegra: colibri_t20: add compatibility comment
  ARM: tegra: colibri_t20: annotate/move sd card detect
  ARM: tegra: colibri_t20: add gpio hogs for gmi_wr_n buffers
  ARM: tegra: colibri_t20: add gpio hog to unreset usb ethernet chip
  ARM: tegra: colibri_t20: add i2c-thermtrip
  ARM: tegra: colibri_t20: annotate/rename lm95245 temperature sensor
  ARM: tegra: colibri_t20: iris: add dr_mode property
  ARM: tegra: colibri_t20: iris: add gpio wakeup key
  ...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'tegra-for-4.20-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

dt-bindings: Changes for v4.20-rc1

This contains the PMC pad configuration bindings which are used to
control the voltage of various pads found on Tegra chips. Among other
things this is required to enable faster modes on SDHCI.

* tag 'tegra-for-4.20-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  dt-bindings: Add Tegra PMC pad configuration bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This device-tree pxa update brings :
 - a couple of changes for future pxa2xx platforms
  - 2 fixes in RTC and I2C domain

* tag 'pxa-dt-4.20' of https://github.com/rjarzmik/linux:
  ARM: dts: pxa: add pincontrol helpers
  ARM: dts: pxa: fix power i2c base address
  ARM: dts: pxa: fix the rtc controller
  ARM: dts: pxa: change serial node names
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

Amlogic ARM64 DT updates for v4.20, round 2
- new SoC support: basic support for G12A family
- new board: Amlogic U200 board, using G12A SoC
- fix SPI bus warnings from new dtc updates

* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  arm64: dts: meson-g12a: add initial g12a s905d2 SoC DT support
  dt-bindings: arm: amlogic: Add Meson G12A binding
  arm64: dts: meson: Fix erroneous SPI bus warnings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

ARM: dts: Amlogic updates for v4.20
- fix clock controller register sizes
- new board: Endless Mini (EC-100) by Endless Mobile
- add voltage regulators

* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM: dts: meson8b: odroidc1: add stdout-path property
  ARM: dts: meson8b: odroidc1: enable the SAR ADC
  ARM: dts: meson8b: odroidc1: add the fixed voltage regulators
  ARM: dts: meson8b: odroidc1: add the CPU voltage regulator
  ARM: dts: meson8b: Add support for the Endless Mini (EC-100)
  ARM: dts: meson8b: add the RMII pins
  ARM: dts: meson8b: add the I2C_A, PWM_C and UART_B pins
  dt-bindings: arm: amlogic: Add the Endless Mobile Endless Mini (EC-100)
  dt-bindings: add vendor prefix for "Endless Mobile, Inc."
  ARM: dts: meson8b: fix the clock controller register size
  ARM: dts: meson8: fix the clock controller register size
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'berlin64-dt-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin into next/dt

Berlin64 DT changes for v4.20

* tag 'berlin64-dt-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin:
  arm64: dts: synaptics: add dtsi file for Synaptics AS370 SoC
  dt-bindings: arm: syna: add support for the AS370 SoC
  dt-bindings: arm: move berlin binding documentation to syna.txt
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'realview-dts-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt

Realview DTS update for v4.20:
- One patch from Rob fixing SPI node names

* tag 'realview-dts-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
  ARM: dts: realview: Fix SPI controller node names
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.

Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.

Cc: Chanho Min <chanho.min@lge.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

dtc has new checks for SPI buses. Fix the warnings in node names.

arch/arm64/boot/dts/amd/amd-overdrive.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'
arch/arm64/boot/dts/amd/amd-overdrive-rev-b0.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'
arch/arm64/boot/dts/amd/amd-overdrive-rev-b1.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'

Cc: Brijesh Singh <brijeshkumar.singh@amd.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

PCIe is not populated by default on iWave RZ/G1N board. RZ/G1N board
is almost identical to RZ/G1M. In order to reuse the common dtsi for
both the boards, it is required to move pcie node from common dtsi
to board specific dts.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add I2C4 support to RZ/G1C (a.k.a. r8a77470) SoC specific
device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add SoC specific device tree definitions for the SDHI2 interface.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add DT node for the Advanced Power Management Unit (APMU), add the
second CPU core, and use "renesas,apmu" as "enable-method".
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Include R-Car Gen1 product names for Bock-W and Marzen.

The product names are taken from:
Documentation/devicetree/bindings/arm/shmobile.txt
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Improve the user friendliness of the DTS code base by including the
R-Car product name in each R-Car Gen2 DTSI file.

The product names are taken from:
Documentation/devicetree/bindings/arm/shmobile.txt
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The PHY found on the A64-OLinuXino requires a TX delay in order to
operate properly. Olimex uses a 600ps second delay in their BSP, and
that has been found to work, so let's use that value in the current
DT.
Signed-off-by: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add initial dtsi file to support Synaptics AS370 SoC with quad
Cortex-A53 CPUs.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>

The AS370 SoC is a new derivative of the berlin family. However, the
SoC isn't named as berlin*.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Rob Herring <robh@kernel.org>

Move berlin binding documentation as part of transition from Marvell
berlin to Synaptics SoC.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Rob Herring <robh@kernel.org>

The power key is controlled solely by the EC, which only tiggeres this
gpio after wakeup.
Fixes immediately return to suspend after wake from LP1.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

ARM: dts: zynq: DT changes for v4.20

- Fix DTS spi/i2c warnings for zc702/zc770 boards
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Fix indentation and alignment when spaces were used instead of tabs.
This fixes checkpatch errors like:

    ERROR: code indent should use tabs where possible
    #306: FILE: arch/arm/boot/dts/tegra20-paz00.dts:306:
    +^I^I         <&tegra_car TEGRA20_CLK_PLL_P_OUT3>;$
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>