Merge branch 'kprobes-test-fixes' of git://git.linaro.org/people/tixy/kernel into fixes

Documentation/DocBook/media/Makefile

@@ -202,8 +202,8 @@ $(MEDIA_OBJ_DIR)/%: $(MEDIA_SRC_DIR)/%.b64
 
 $(MEDIA_OBJ_DIR)/v4l2.xml: $(OBJIMGFILES)
 	@$($(quiet)gen_xml)
-	@(ln -sf $(MEDIA_SRC_DIR)/v4l/*xml $(MEDIA_OBJ_DIR)/)
-	@(ln -sf $(MEDIA_SRC_DIR)/dvb/*xml $(MEDIA_OBJ_DIR)/)
+	@(ln -sf `cd $(MEDIA_SRC_DIR) && /bin/pwd`/v4l/*xml $(MEDIA_OBJ_DIR)/)
+	@(ln -sf `cd $(MEDIA_SRC_DIR) && /bin/pwd`/dvb/*xml $(MEDIA_OBJ_DIR)/)
 
 $(MEDIA_OBJ_DIR)/videodev2.h.xml: $(srctree)/include/uapi/linux/videodev2.h $(MEDIA_OBJ_DIR)/v4l2.xml
 	@$($(quiet)gen_xml)

Documentation/devicetree/bindings/i2c/i2c-rk3x.txt

+* Rockchip RK3xxx I2C controller
+
+This driver interfaces with the native I2C controller present in Rockchip
+RK3xxx SoCs.
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : should be "rockchip,rk3066-i2c", "rockchip,rk3188-i2c" or
+		"rockchip,rk3288-i2c".
+ - interrupts : interrupt number
+ - clocks : parent clock
+
+Required on RK3066, RK3188 :
+
+ - rockchip,grf : the phandle of the syscon node for the general register
+		  file (GRF)
+ - on those SoCs an alias with the correct I2C bus ID (bit offset in the GRF)
+   is also required.
+
+Optional properties :
+
+ - clock-frequency : SCL frequency to use (in Hz). If omitted, 100kHz is used.
+
+Example:
+
+aliases {
+	i2c0 = &i2c0;
+}
+
+i2c0: i2c@2002d000 {
+	compatible = "rockchip,rk3188-i2c";
+	reg = <0x2002d000 0x1000>;
+	interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	rockchip,grf = <&grf>;
+
+	clock-names = "i2c";
+	clocks = <&cru PCLK_I2C0>;
+};

Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt

+
+* Allwinner P2WI (Push/Pull 2 Wire Interface) controller
+
+Required properties :
+
+ - reg             : Offset and length of the register set for the device.
+ - compatible      : Should one of the following:
+                     - "allwinner,sun6i-a31-p2wi"
+ - interrupts      : The interrupt line connected to the P2WI peripheral.
+ - clocks          : The gate clk connected to the P2WI peripheral.
+ - resets          : The reset line connected to the P2WI peripheral.
+
+Optional properties :
+
+ - clock-frequency : Desired P2WI bus clock frequency in Hz. If not set the
+default frequency is 100kHz
+
+A P2WI may contain one child node encoding a P2WI slave device.
+
+Slave device properties:
+  Required properties:
+   - reg           : the I2C slave address used during the initialization
+                     process to switch from I2C to P2WI mode
+
+Example:
+
+	p2wi@01f03400 {
+		compatible = "allwinner,sun6i-a31-p2wi";
+		reg = <0x01f03400 0x400>;
+		interrupts = <0 39 4>;
+		clocks = <&apb0_gates 3>;
+		clock-frequency = <6000000>;
+		resets = <&apb0_rst 3>;
+
+		axp221: pmic@68 {
+			compatible = "x-powers,axp221";
+			reg = <0x68>;
+
+			/* ... */
+		};
+	};

Documentation/kbuild/makefiles.txt

@@ -1171,7 +1171,7 @@ When kbuild executes, the following steps are followed (roughly):
 	      obvious reason.
 
     dtc
-	Create flattend device tree blob object suitable for linking
+	Create flattened device tree blob object suitable for linking
 	into vmlinux. Device tree blobs linked into vmlinux are placed
 	in an init section in the image. Platform code *must* copy the
 	blob to non-init memory prior to calling unflatten_device_tree().

Documentation/kernel-parameters.txt

@@ -1474,6 +1474,13 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 	js=		[HW,JOY] Analog joystick
 			See Documentation/input/joystick.txt.
 
+	kaslr/nokaslr	[X86]
+			Enable/disable kernel and module base offset ASLR
+			(Address Space Layout Randomization) if built into
+			the kernel. When CONFIG_HIBERNATION is selected,
+			kASLR is disabled by default. When kASLR is enabled,
+			hibernation will be disabled.
+
 	keepinitrd	[HW,ARM]
 
 	kernelcore=nn[KMG]	[KNL,X86,IA-64,PPC] This parameter
@@ -2110,10 +2117,6 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 	noapic		[SMP,APIC] Tells the kernel to not make use of any
 			IOAPICs that may be present in the system.
 
-	nokaslr		[X86]
-			Disable kernel and module base offset ASLR (Address
-			Space Layout Randomization) if built into the kernel.
-
 	noautogroup	Disable scheduler automatic task group creation.
 
 	nobats		[PPC] Do not use BATs for mapping kernel lowmem
@@ -2184,6 +2187,8 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			in certain environments such as networked servers or
 			real-time systems.
 
+	nohibernate	[HIBERNATION] Disable hibernation and resume.
+
 	nohz=		[KNL] Boottime enable/disable dynamic ticks
 			Valid arguments: on, off
 			Default: on
@@ -2980,6 +2985,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 		noresume	Don't check if there's a hibernation image
 				present during boot.
 		nocompress	Don't compress/decompress hibernation images.
+		no		Disable hibernation and resume.
 
 	retain_initrd	[RAM] Keep initrd memory after extraction
 

Documentation/thermal/nouveau_thermal

@@ -4,7 +4,7 @@ Kernel driver nouveau
 Supported chips:
 * NV43+
 
-Authors: Martin Peres (mupuf) <martin.peres@labri.fr>
+Authors: Martin Peres (mupuf) <martin.peres@free.fr>
 
 Description
 ---------
@@ -68,8 +68,9 @@ Your fan can be driven in different modes:
 
 NOTE: Be sure to use the manual mode if you want to drive the fan speed manually
 
-NOTE2: Not all fan management modes may be supported on all chipsets. We are
-working on it.
+NOTE2: When operating in manual mode outside the vbios-defined
+[PWM_min, PWM_max] range, the reported fan speed (RPM) may not be accurate
+depending on your hardware.
 
 Bug reports
 ---------

MAINTAINERS

@@ -6960,7 +6960,7 @@ PKUNITY SOC DRIVERS
 M:	Guan Xuetao <gxt@mprc.pku.edu.cn>
 W:	http://mprc.pku.edu.cn/~guanxuetao/linux
 S:	Maintained
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/epip/linux-2.6-unicore32.git
+T:	git git://github.com/gxt/linux.git
 F:	drivers/input/serio/i8042-unicore32io.h
 F:	drivers/i2c/busses/i2c-puv3.c
 F:	drivers/video/fb-puv3.c
@@ -7948,6 +7948,7 @@ F:	drivers/mmc/host/sdhci-spear.c
 
 SECURITY SUBSYSTEM
 M:	James Morris <james.l.morris@oracle.com>
+M:	Serge E. Hallyn <serge@hallyn.com>
 L:	linux-security-module@vger.kernel.org (suggested Cc:)
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security.git
 W:	http://kernsec.org/
@@ -9276,7 +9277,7 @@ UNICORE32 ARCHITECTURE:
 M:	Guan Xuetao <gxt@mprc.pku.edu.cn>
 W:	http://mprc.pku.edu.cn/~guanxuetao/linux
 S:	Maintained
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/epip/linux-2.6-unicore32.git
+T:	git git://github.com/gxt/linux.git
 F:	arch/unicore32/
 
 UNIFDEF
@@ -9743,6 +9744,14 @@ L:	virtualization@lists.linux-foundation.org
 S:	Supported
 F:	arch/x86/kernel/cpu/vmware.c
 
+VMWARE BALLOON DRIVER
+M:	Xavier Deguillard <xdeguillard@vmware.com>
+M:	Philip Moltmann <moltmann@vmware.com>
+M:	"VMware, Inc." <pv-drivers@vmware.com>
+L:	linux-kernel@vger.kernel.org
+S:	Maintained
+F:	drivers/misc/vmw_balloon.c
+
 VMWARE VMXNET3 ETHERNET DRIVER
 M:	Shreyas Bhatewara <sbhatewara@vmware.com>
 M:	"VMware, Inc." <pv-drivers@vmware.com>

Makefile

 VERSION = 3
 PATCHLEVEL = 16
 SUBLEVEL = 0
-EXTRAVERSION = -rc1
+EXTRAVERSION = -rc2
 NAME = Shuffling Zombie Juror
 
 # *DOCUMENTATION*

arch/arm/Kconfig

@@ -175,13 +175,6 @@ config ARCH_HAS_ILOG2_U32
 config ARCH_HAS_ILOG2_U64
 	bool
 
-config ARCH_HAS_CPUFREQ
-	bool
-	help
-	  Internal node to signify that the ARCH has CPUFREQ support
-	  and that the relevant menu configurations are displayed for
-	  it.
-
 config ARCH_HAS_BANDGAP
 	bool
 
@@ -318,7 +311,6 @@ config ARCH_MULTIPLATFORM
 
 config ARCH_INTEGRATOR
 	bool "ARM Ltd. Integrator family"
-	select ARCH_HAS_CPUFREQ
 	select ARM_AMBA
 	select ARM_PATCH_PHYS_VIRT
 	select AUTO_ZRELADDR
@@ -538,7 +530,6 @@ config ARCH_DOVE
 
 config ARCH_KIRKWOOD
 	bool "Marvell Kirkwood"
-	select ARCH_HAS_CPUFREQ
 	select ARCH_REQUIRE_GPIOLIB
 	select CPU_FEROCEON
 	select GENERIC_CLOCKEVENTS
@@ -637,7 +628,6 @@ config ARCH_LPC32XX
 config ARCH_PXA
 	bool "PXA2xx/PXA3xx-based"
 	depends on MMU
-	select ARCH_HAS_CPUFREQ
 	select ARCH_MTD_XIP
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_CPU_SUSPEND if PM
@@ -707,7 +697,6 @@ config ARCH_RPC
 
 config ARCH_SA1100
 	bool "SA1100-based"
-	select ARCH_HAS_CPUFREQ
 	select ARCH_MTD_XIP
 	select ARCH_REQUIRE_GPIOLIB
 	select ARCH_SPARSEMEM_ENABLE
@@ -725,7 +714,6 @@ config ARCH_SA1100
 
 config ARCH_S3C24XX
 	bool "Samsung S3C24XX SoCs"
-	select ARCH_HAS_CPUFREQ
 	select ARCH_REQUIRE_GPIOLIB
 	select ATAGS
 	select CLKDEV_LOOKUP
@@ -746,7 +734,6 @@ config ARCH_S3C24XX
 
 config ARCH_S3C64XX
 	bool "Samsung S3C64XX"
-	select ARCH_HAS_CPUFREQ
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_AMBA
 	select ARM_VIC
@@ -809,7 +796,6 @@ config ARCH_S5PC100
 
 config ARCH_S5PV210
 	bool "Samsung S5PV210/S5PC110"
-	select ARCH_HAS_CPUFREQ
 	select ARCH_HAS_HOLES_MEMORYMODEL
 	select ARCH_SPARSEMEM_ENABLE
 	select ATAGS
@@ -845,7 +831,6 @@ config ARCH_DAVINCI
 config ARCH_OMAP1
 	bool "TI OMAP1"
 	depends on MMU
-	select ARCH_HAS_CPUFREQ
 	select ARCH_HAS_HOLES_MEMORYMODEL
 	select ARCH_OMAP
 	select ARCH_REQUIRE_GPIOLIB
@@ -1009,8 +994,6 @@ source "arch/arm/mach-rockchip/Kconfig"
 
 source "arch/arm/mach-sa1100/Kconfig"
 
-source "arch/arm/plat-samsung/Kconfig"
-
 source "arch/arm/mach-socfpga/Kconfig"
 
 source "arch/arm/mach-spear/Kconfig"
@@ -1028,6 +1011,7 @@ source "arch/arm/mach-s5pc100/Kconfig"
 source "arch/arm/mach-s5pv210/Kconfig"
 
 source "arch/arm/mach-exynos/Kconfig"
+source "arch/arm/plat-samsung/Kconfig"
 
 source "arch/arm/mach-shmobile/Kconfig"
 
@@ -2109,9 +2093,7 @@ endmenu
 
 menu "CPU Power Management"
 
-if ARCH_HAS_CPUFREQ
 source "drivers/cpufreq/Kconfig"
-endif
 
 source "drivers/cpuidle/Kconfig"
 

arch/arm/boot/dts/armada-375-db.dts

@@ -91,6 +91,8 @@ nand: nand@d0000 {
 				marvell,nand-keep-config;
 				marvell,nand-enable-arbiter;
 				nand-on-flash-bbt;
+				nand-ecc-strength = <4>;
+				nand-ecc-step-size = <512>;
 
 				partition@0 {
 					label = "U-Boot";

arch/arm/boot/dts/armada-385-db.dts

@@ -98,6 +98,8 @@ flash@d0000 {
 				marvell,nand-keep-config;
 				marvell,nand-enable-arbiter;
 				nand-on-flash-bbt;
+				nand-ecc-strength = <4>;
+				nand-ecc-step-size = <512>;
 
 				partition@0 {
 					label = "U-Boot";

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts

@@ -25,7 +25,7 @@ chosen {
 
 	memory {
 		device_type = "memory";
-		reg = <0 0x00000000 0 0xC0000000>; /* 3 GB */
+		reg = <0 0x00000000 0 0x40000000>; /* 1 GB soldered on */
 	};
 
 	soc {

arch/arm/configs/multi_v7_defconfig

@@ -300,6 +300,7 @@ CONFIG_MMC=y
 CONFIG_MMC_BLOCK_MINORS=16
 CONFIG_MMC_ARMMMCI=y
 CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_SDHCI_OF_ARASAN=y
 CONFIG_MMC_SDHCI_ESDHC_IMX=y
 CONFIG_MMC_SDHCI_DOVE=y

arch/arm/configs/omap2plus_defconfig

@@ -32,6 +32,7 @@ CONFIG_SOC_OMAP5=y
 CONFIG_SOC_AM33XX=y
 CONFIG_SOC_AM43XX=y
 CONFIG_SOC_DRA7XX=y
+CONFIG_CACHE_L2X0=y
 CONFIG_ARM_THUMBEE=y
 CONFIG_ARM_ERRATA_411920=y
 CONFIG_SMP=y

arch/arm/include/asm/ftrace.h

@@ -52,7 +52,7 @@ extern inline void *return_address(unsigned int level)
 
 #endif
 
-#define ftrace_return_addr(n) return_address(n)
+#define ftrace_return_address(n) return_address(n)
 
 #endif /* ifndef __ASSEMBLY__ */
 

arch/arm/kernel/kprobes-test-arm.c

@@ -74,8 +74,6 @@ void kprobe_arm_test_cases(void)
 	TEST_RRR( op "lt" s "	r11, r",11,VAL1,", r",14,N(val),", asr r",7, 6,"")\
 	TEST_RR(  op "gt" s "	r12, r13"       ", r",14,val, ", ror r",14,7,"")\
 	TEST_RR(  op "le" s "	r14, r",0, val, ", r13"       ", lsl r",14,8,"")\
-	TEST_RR(  op s "	r12, pc"        ", r",14,val, ", ror r",14,7,"")\
-	TEST_RR(  op s "	r14, r",0, val, ", pc"        ", lsl r",14,8,"")\
 	TEST_R(   op "eq" s "	r0,  r",11,VAL1,", #0xf5")			\
 	TEST_R(   op "ne" s "	r11, r",0, VAL1,", #0xf5000000")		\
 	TEST_R(   op s "	r7,  r",8, VAL2,", #0x000af000")		\
@@ -103,8 +101,6 @@ void kprobe_arm_test_cases(void)
 	TEST_RRR( op "ge	r",11,VAL1,", r",14,N(val),", asr r",7, 6,"")	\
 	TEST_RR(  op "le	r13"       ", r",14,val, ", ror r",14,7,"")	\
 	TEST_RR(  op "gt	r",0, val, ", r13"       ", lsl r",14,8,"")	\
-	TEST_RR(  op "	pc"        ", r",14,val, ", ror r",14,7,"")		\
-	TEST_RR(  op "	r",0, val, ", pc"        ", lsl r",14,8,"")		\
 	TEST_R(   op "eq	r",11,VAL1,", #0xf5")				\
 	TEST_R(   op "ne	r",0, VAL1,", #0xf5000000")			\
 	TEST_R(   op "	r",8, VAL2,", #0x000af000")
@@ -125,7 +121,6 @@ void kprobe_arm_test_cases(void)
 	TEST_RR(  op "ge" s "	r11, r",11,N(val),", asr r",7, 6,"")	\
 	TEST_RR(  op "lt" s "	r12, r",11,val, ", ror r",14,7,"")	\
 	TEST_R(   op "gt" s "	r14, r13"       ", lsl r",14,8,"")	\
-	TEST_R(   op "le" s "	r14, pc"        ", lsl r",14,8,"")	\
 	TEST(     op "eq" s "	r0,  #0xf5")				\
 	TEST(     op "ne" s "	r11, #0xf5000000")			\
 	TEST(     op s "	r7,  #0x000af000")			\
@@ -159,12 +154,19 @@ void kprobe_arm_test_cases(void)
 	TEST_SUPPORTED("cmp	pc, #0x1000");
 	TEST_SUPPORTED("cmp	sp, #0x1000");
 
-	/* Data-processing with PC as shift*/
+	/* Data-processing with PC and a shift count in a register */
 	TEST_UNSUPPORTED(__inst_arm(0xe15c0f1e) "	@ cmp	r12, r14, asl pc")
 	TEST_UNSUPPORTED(__inst_arm(0xe1a0cf1e) "	@ mov	r12, r14, asl pc")
 	TEST_UNSUPPORTED(__inst_arm(0xe08caf1e) "	@ add	r10, r12, r14, asl pc")
-
-	/* Data-processing with PC as shift*/
+	TEST_UNSUPPORTED(__inst_arm(0xe151021f) "	@ cmp	r1, pc, lsl r2")
+	TEST_UNSUPPORTED(__inst_arm(0xe17f0211) "	@ cmn	pc, r1, lsl r2")
+	TEST_UNSUPPORTED(__inst_arm(0xe1a0121f) "	@ mov	r1, pc, lsl r2")
+	TEST_UNSUPPORTED(__inst_arm(0xe1a0f211) "	@ mov	pc, r1, lsl r2")
+	TEST_UNSUPPORTED(__inst_arm(0xe042131f) "	@ sub	r1, r2, pc, lsl r3")
+	TEST_UNSUPPORTED(__inst_arm(0xe1cf1312) "	@ bic	r1, pc, r2, lsl r3")
+	TEST_UNSUPPORTED(__inst_arm(0xe081f312) "	@ add	pc, r1, r2, lsl r3")
+
+	/* Data-processing with PC as a target and status registers updated */
 	TEST_UNSUPPORTED("movs	pc, r1")
 	TEST_UNSUPPORTED("movs	pc, r1, lsl r2")
 	TEST_UNSUPPORTED("movs	pc, #0x10000")
@@ -187,14 +189,14 @@ void kprobe_arm_test_cases(void)
 	TEST_BF_R ("add	pc, pc, r",14,2f-1f-8,"")
 	TEST_BF_R ("add	pc, r",14,2f-1f-8,", pc")
 	TEST_BF_R ("mov	pc, r",0,2f,"")
-	TEST_BF_RR("mov	pc, r",0,2f,", asl r",1,0,"")
+	TEST_BF_R ("add	pc, pc, r",14,(2f-1f-8)*2,", asr #1")
 	TEST_BB(   "sub	pc, pc, #1b-2b+8")
 #if __LINUX_ARM_ARCH__ == 6 && !defined(CONFIG_CPU_V7)
 	TEST_BB(   "sub	pc, pc, #1b-2b+8-2") /* UNPREDICTABLE before and after ARMv6 */
 #endif
 	TEST_BB_R( "sub	pc, pc, r",14, 1f-2f+8,"")
 	TEST_BB_R( "rsb	pc, r",14,1f-2f+8,", pc")
-	TEST_RR(   "add	pc, pc, r",10,-2,", asl r",11,1,"")
+	TEST_R(    "add	pc, pc, r",10,-2,", asl #1")
 #ifdef CONFIG_THUMB2_KERNEL
 	TEST_ARM_TO_THUMB_INTERWORK_R("add	pc, pc, r",0,3f-1f-8+1,"")
 	TEST_ARM_TO_THUMB_INTERWORK_R("sub	pc, r",0,3f+8+1,", #8")
@@ -216,6 +218,7 @@ void kprobe_arm_test_cases(void)
 	TEST_BB_R("bx	r",7,2f,"")
 	TEST_BF_R("bxeq	r",14,2f,"")
 
+#if __LINUX_ARM_ARCH__ >= 5
 	TEST_R("clz	r0, r",0, 0x0,"")
 	TEST_R("clzeq	r7, r",14,0x1,"")
 	TEST_R("clz	lr, r",7, 0xffffffff,"")
@@ -337,6 +340,7 @@ void kprobe_arm_test_cases(void)
 	TEST_UNSUPPORTED(__inst_arm(0xe16f02e1) " @ smultt pc, r1, r2")
 	TEST_UNSUPPORTED(__inst_arm(0xe16002ef) " @ smultt r0, pc, r2")
 	TEST_UNSUPPORTED(__inst_arm(0xe1600fe1) " @ smultt r0, r1, pc")
+#endif
 
 	TEST_GROUP("Multiply and multiply-accumulate")
 
@@ -559,6 +563,7 @@ void kprobe_arm_test_cases(void)
 	TEST_UNSUPPORTED("ldrsht	r1, [r2], #48")
 #endif
 
+#if __LINUX_ARM_ARCH__ >= 5
 	TEST_RPR(  "strd	r",0, VAL1,", [r",1, 48,", -r",2,24,"]")
 	TEST_RPR(  "strccd	r",8, VAL2,", [r",13,0, ", r",12,48,"]")
 	TEST_RPR(  "strd	r",4, VAL1,", [r",2, 24,", r",3, 48,"]!")
@@ -595,6 +600,7 @@ void kprobe_arm_test_cases(void)
 	TEST_UNSUPPORTED(__inst_arm(0xe1efc3d0) "	@ ldrd r12, [pc, #48]!")
 	TEST_UNSUPPORTED(__inst_arm(0xe0c9f3d0) "	@ ldrd pc, [r9], #48")
 	TEST_UNSUPPORTED(__inst_arm(0xe0c9e3d0) "	@ ldrd lr, [r9], #48")
+#endif
 
 	TEST_GROUP("Miscellaneous")
 
@@ -1227,7 +1233,9 @@ void kprobe_arm_test_cases(void)
 	TEST_COPROCESSOR( "mrc"two"	0, 0, r0, cr0, cr0, 0")
 
 	COPROCESSOR_INSTRUCTIONS_ST_LD("",e)
+#if __LINUX_ARM_ARCH__ >= 5
 	COPROCESSOR_INSTRUCTIONS_MC_MR("",e)
+#endif
 	TEST_UNSUPPORTED("svc	0")
 	TEST_UNSUPPORTED("svc	0xffffff")
 
@@ -1287,7 +1295,9 @@ void kprobe_arm_test_cases(void)
 	TEST(	"blx	__dummy_thumb_subroutine_odd")
 #endif /* __LINUX_ARM_ARCH__ >= 6 */
 
+#if __LINUX_ARM_ARCH__ >= 5
 	COPROCESSOR_INSTRUCTIONS_ST_LD("2",f)
+#endif
 #if __LINUX_ARM_ARCH__ >= 6
 	COPROCESSOR_INSTRUCTIONS_MC_MR("2",f)
 #endif

arch/arm/kernel/kprobes-test.c

@@ -225,6 +225,7 @@ static int pre_handler_called;
 static int post_handler_called;
 static int jprobe_func_called;
 static int kretprobe_handler_called;
+static int tests_failed;
 
 #define FUNC_ARG1 0x12345678
 #define FUNC_ARG2 0xabcdef
@@ -461,6 +462,13 @@ static int run_api_tests(long (*func)(long, long))
 
 	pr_info("    jprobe\n");
 	ret = test_jprobe(func);
+#if defined(CONFIG_THUMB2_KERNEL) && !defined(MODULE)
+	if (ret == -EINVAL) {
+		pr_err("FAIL: Known longtime bug with jprobe on Thumb kernels\n");
+		tests_failed = ret;
+		ret = 0;
+	}
+#endif
 	if (ret < 0)
 		return ret;
 
@@ -1671,6 +1679,8 @@ static int __init run_all_tests(void)
 #endif
 
 out:
+	if (ret == 0)
+		ret = tests_failed;
 	if (ret == 0)
 		pr_info("Finished kprobe tests OK\n");
 	else

arch/arm/kernel/probes-arm.c

@@ -341,12 +341,12 @@ static const union decode_item arm_cccc_000x_table[] = {
 	/* CMP (reg-shift reg)	cccc 0001 0101 xxxx xxxx xxxx 0xx1 xxxx */
 	/* CMN (reg-shift reg)	cccc 0001 0111 xxxx xxxx xxxx 0xx1 xxxx */
 	DECODE_EMULATEX	(0x0f900090, 0x01100010, PROBES_DATA_PROCESSING_REG,
-						 REGS(ANY, 0, NOPC, 0, ANY)),
+						 REGS(NOPC, 0, NOPC, 0, NOPC)),
 
 	/* MOV (reg-shift reg)	cccc 0001 101x xxxx xxxx xxxx 0xx1 xxxx */
 	/* MVN (reg-shift reg)	cccc 0001 111x xxxx xxxx xxxx 0xx1 xxxx */
 	DECODE_EMULATEX	(0x0fa00090, 0x01a00010, PROBES_DATA_PROCESSING_REG,
-						 REGS(0, ANY, NOPC, 0, ANY)),
+						 REGS(0, NOPC, NOPC, 0, NOPC)),
 
 	/* AND (reg-shift reg)	cccc 0000 000x xxxx xxxx xxxx 0xx1 xxxx */
 	/* EOR (reg-shift reg)	cccc 0000 001x xxxx xxxx xxxx 0xx1 xxxx */
@@ -359,7 +359,7 @@ static const union decode_item arm_cccc_000x_table[] = {
 	/* ORR (reg-shift reg)	cccc 0001 100x xxxx xxxx xxxx 0xx1 xxxx */
 	/* BIC (reg-shift reg)	cccc 0001 110x xxxx xxxx xxxx 0xx1 xxxx */
 	DECODE_EMULATEX	(0x0e000090, 0x00000010, PROBES_DATA_PROCESSING_REG,
-						 REGS(ANY, ANY, NOPC, 0, ANY)),
+						 REGS(NOPC, NOPC, NOPC, 0, NOPC)),
 
 	DECODE_END
 };

arch/arm/mach-bcm/Kconfig

-config ARCH_BCM
+menuconfig ARCH_BCM
 	bool "Broadcom SoC Support" if ARCH_MULTI_V6_V7
 	help
 	  This enables support for Broadcom ARM based SoC chips
 
-menu "Broadcom SoC Selection"
-	depends on ARCH_BCM
+if ARCH_BCM
 
 config ARCH_BCM_MOBILE
 	bool "Broadcom Mobile SoC Support" if ARCH_MULTI_V7
@@ -88,4 +87,4 @@ config ARCH_BCM_5301X
 	  different SoC or with the older BCM47XX and BCM53XX based
 	  network SoC using a MIPS CPU, they are supported by arch/mips/bcm47xx
 
-endmenu
+endif

arch/arm/mach-berlin/Kconfig

-config ARCH_BERLIN
+menuconfig ARCH_BERLIN
 	bool "Marvell Berlin SoCs" if ARCH_MULTI_V7
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_GIC
@@ -9,8 +9,6 @@ config ARCH_BERLIN
 
 if ARCH_BERLIN
 
-menu "Marvell Berlin SoC variants"
-
 config MACH_BERLIN_BG2
 	bool "Marvell Armada 1500 (BG2)"
 	select CACHE_L2X0
@@ -30,6 +28,4 @@ config MACH_BERLIN_BG2Q
 	select HAVE_ARM_TWD if SMP
 	select PINCTRL_BERLIN_BG2Q
 
-endmenu
-
 endif

arch/arm/mach-cns3xxx/Kconfig

-config ARCH_CNS3XXX
+menuconfig ARCH_CNS3XXX
 	bool "Cavium Networks CNS3XXX family" if ARCH_MULTI_V6
 	select ARM_GIC
 	select PCI_DOMAINS if PCI
 	help
 	  Support for Cavium Networks CNS3XXX platform.
 
-menu "CNS3XXX platform type"
-	depends on ARCH_CNS3XXX
+if ARCH_CNS3XXX
 
 config MACH_CNS3420VB
 	bool "Support for CNS3420 Validation Board"
@@ -17,4 +16,4 @@ config MACH_CNS3420VB
 	  This is a platform with an on-board ARM11 MPCore and has support
 	  for USB, USB-OTG, MMC/SD/SDIO, SATA, PCI-E, etc.
 
-endmenu
+endif

arch/arm/mach-davinci/Kconfig

@@ -39,7 +39,6 @@ config ARCH_DAVINCI_DA830
 config ARCH_DAVINCI_DA850
 	bool "DA850/OMAP-L138/AM18x based system"
 	select ARCH_DAVINCI_DA8XX
-	select ARCH_HAS_CPUFREQ
 	select CP_INTC
 
 config ARCH_DAVINCI_DA8XX

arch/arm/mach-exynos/Kconfig

@@ -7,10 +7,9 @@
 
 # Configuration options for the EXYNOS4
 
-config ARCH_EXYNOS
+menuconfig ARCH_EXYNOS
 	bool "Samsung EXYNOS" if ARCH_MULTI_V7
 	select ARCH_HAS_BANDGAP
-	select ARCH_HAS_CPUFREQ
 	select ARCH_HAS_HOLES_MEMORYMODEL
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_AMBA
@@ -30,8 +29,6 @@ config ARCH_EXYNOS
 
 if ARCH_EXYNOS
 
-menu "SAMSUNG EXYNOS SoCs Support"
-
 config ARCH_EXYNOS3
 	bool "SAMSUNG EXYNOS3"
 	select ARM_CPU_SUSPEND if PM
@@ -118,8 +115,6 @@ config SOC_EXYNOS5800
 	default y
 	depends on SOC_EXYNOS5420
 
-endmenu
-
 config EXYNOS5420_MCPM
 	bool "Exynos5420 Multi-Cluster PM support"
 	depends on MCPM && SOC_EXYNOS5420

arch/arm/mach-exynos/common.h

@@ -118,6 +118,7 @@ extern void __iomem *sysram_ns_base_addr;
 extern void __iomem *sysram_base_addr;
 void exynos_init_io(void);
 void exynos_restart(enum reboot_mode mode, const char *cmd);
+void exynos_sysram_init(void);
 void exynos_cpuidle_init(void);
 void exynos_cpufreq_init(void);
 void exynos_init_late(void);

arch/arm/mach-exynos/exynos.c

@@ -184,6 +184,28 @@ void __init exynos_cpufreq_init(void)
 	platform_device_register_simple("exynos-cpufreq", -1, NULL, 0);
 }
 
+void __iomem *sysram_base_addr;
+void __iomem *sysram_ns_base_addr;
+
+void __init exynos_sysram_init(void)
+{
+	struct device_node *node;
+
+	for_each_compatible_node(node, NULL, "samsung,exynos4210-sysram") {
+		if (!of_device_is_available(node))
+			continue;
+		sysram_base_addr = of_iomap(node, 0);
+		break;
+	}
+
+	for_each_compatible_node(node, NULL, "samsung,exynos4210-sysram-ns") {
+		if (!of_device_is_available(node))
+			continue;
+		sysram_ns_base_addr = of_iomap(node, 0);
+		break;
+	}
+}
+
 void __init exynos_init_late(void)
 {
 	if (of_machine_is_compatible("samsung,exynos5440"))
@@ -198,7 +220,7 @@ static int __init exynos_fdt_map_chipid(unsigned long node, const char *uname,
 					int depth, void *data)
 {
 	struct map_desc iodesc;
-	__be32 *reg;
+	const __be32 *reg;
 	int len;
 
 	if (!of_flat_dt_is_compatible(node, "samsung,exynos4210-chipid") &&
@@ -271,6 +293,13 @@ static void __init exynos_dt_machine_init(void)
 		}
 	}
 
+	/*
+	 * This is called from smp_prepare_cpus if we've built for SMP, but
+	 * we still need to set it up for PM and firmware ops if not.
+	 */
+	if (!IS_ENABLED(SMP))
+		exynos_sysram_init();
+
 	exynos_cpuidle_init();
 	exynos_cpufreq_init();
 

arch/arm/mach-exynos/platsmp.c

@@ -32,28 +32,6 @@
 
 extern void exynos4_secondary_startup(void);
 
-void __iomem *sysram_base_addr;
-void __iomem *sysram_ns_base_addr;
-
-static void __init exynos_smp_prepare_sysram(void)
-{
-	struct device_node *node;
-
-	for_each_compatible_node(node, NULL, "samsung,exynos4210-sysram") {
-		if (!of_device_is_available(node))
-			continue;
-		sysram_base_addr = of_iomap(node, 0);
-		break;
-	}
-
-	for_each_compatible_node(node, NULL, "samsung,exynos4210-sysram-ns") {
-		if (!of_device_is_available(node))
-			continue;
-		sysram_ns_base_addr = of_iomap(node, 0);
-		break;
-	}
-}
-
 static inline void __iomem *cpu_boot_reg_base(void)
 {
 	if (soc_is_exynos4210() && samsung_rev() == EXYNOS4210_REV_1_1)
@@ -234,11 +212,11 @@ static void __init exynos_smp_prepare_cpus(unsigned int max_cpus)
 {
 	int i;
 
+	exynos_sysram_init();
+
 	if (read_cpuid_part_number() == ARM_CPU_PART_CORTEX_A9)
 		scu_enable(scu_base_addr());
 
-	exynos_smp_prepare_sysram();
-
 	/*
 	 * Write the address of secondary startup into the
 	 * system-wide flags register. The boot monitor waits

arch/arm/mach-highbank/Kconfig

 config ARCH_HIGHBANK
 	bool "Calxeda ECX-1000/2000 (Highbank/Midway)" if ARCH_MULTI_V7
 	select ARCH_DMA_ADDR_T_64BIT if ARM_LPAE
-	select ARCH_HAS_CPUFREQ
 	select ARCH_HAS_HOLES_MEMORYMODEL
 	select ARCH_HAS_OPP
 	select ARCH_SUPPORTS_BIG_ENDIAN

arch/arm/mach-imx/Kconfig

-config ARCH_MXC
+menuconfig ARCH_MXC
 	bool "Freescale i.MX family" if ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7
-	select ARCH_HAS_CPUFREQ
 	select ARCH_HAS_OPP
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_CPU_SUSPEND if PM
@@ -13,8 +12,7 @@ config ARCH_MXC
 	help
 	  Support for Freescale MXC/iMX-based family of processors
 
-menu "Freescale i.MX support"
-	depends on ARCH_MXC
+if ARCH_MXC
 
 config MXC_TZIC
 	bool
@@ -99,7 +97,6 @@ config SOC_IMX25
 
 config SOC_IMX27
 	bool
-	select ARCH_HAS_CPUFREQ
 	select ARCH_HAS_OPP
 	select CPU_ARM926T
 	select IMX_HAVE_IOMUX_V1
@@ -124,7 +121,6 @@ config SOC_IMX35
 
 config SOC_IMX5
 	bool
-	select ARCH_HAS_CPUFREQ
 	select ARCH_HAS_OPP
 	select ARCH_MXC_IOMUX_V3
 	select MXC_TZIC
@@ -786,4 +782,4 @@ endif
 
 source "arch/arm/mach-imx/devices/Kconfig"
 
-endmenu
+endif

arch/arm/mach-integrator/Kconfig

@@ -28,7 +28,7 @@ config ARCH_CINTEGRATOR
 	bool
 
 config INTEGRATOR_IMPD1
-	tristate "Include support for Integrator/IM-PD1"
+	bool "Include support for Integrator/IM-PD1"
 	depends on ARCH_INTEGRATOR_AP
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_VIC

arch/arm/mach-integrator/impd1.c

@@ -308,7 +308,12 @@ static struct impd1_device impd1_devs[] = {
  */
 #define IMPD1_VALID_IRQS 0x00000bffU
 
-static int __init impd1_probe(struct lm_device *dev)
+/*
+ * As this module is bool, it is OK to have this as __init_refok() - no
+ * probe calls will be done after the initial system bootup, as devices
+ * are discovered as part of the machine startup.
+ */
+static int __init_refok impd1_probe(struct lm_device *dev)
 {
 	struct impd1_module *impd1;
 	int irq_base;
@@ -397,6 +402,11 @@ static void impd1_remove(struct lm_device *dev)
 static struct lm_driver impd1_driver = {
 	.drv = {
 		.name	= "impd1",
+		/*
+		 * As we're dropping the probe() function, suppress driver
+		 * binding from sysfs.
+		 */
+		.suppress_bind_attrs = true,
 	},
 	.probe		= impd1_probe,
 	.remove		= impd1_remove,

arch/arm/mach-keystone/Kconfig

 config ARCH_KEYSTONE
 	bool "Texas Instruments Keystone Devices"
 	depends on ARCH_MULTI_V7
+	depends on ARM_PATCH_PHYS_VIRT
 	select ARM_GIC
 	select HAVE_ARM_ARCH_TIMER
 	select CLKSRC_MMIO

arch/arm/mach-moxart/Kconfig

-config ARCH_MOXART
+menuconfig ARCH_MOXART
 	bool "MOXA ART SoC" if ARCH_MULTI_V4
 	select CPU_FA526
 	select ARM_DMA_MEM_BUFFERABLE

arch/arm/mach-mvebu/Kconfig

-config ARCH_MVEBU
+menuconfig ARCH_MVEBU
 	bool "Marvell Engineering Business Unit (MVEBU) SoCs" if (ARCH_MULTI_V7 || ARCH_MULTI_V5)
 	select ARCH_SUPPORTS_BIG_ENDIAN
 	select CLKSRC_MMIO
@@ -13,8 +13,6 @@ config ARCH_MVEBU
 
 if ARCH_MVEBU
 
-menu "Marvell EBU SoC variants"
-
 config MACH_MVEBU_V7
 	bool
 	select ARMADA_370_XP_TIMER
@@ -84,7 +82,6 @@ config MACH_DOVE
 
 config MACH_KIRKWOOD
 	bool "Marvell Kirkwood boards" if ARCH_MULTI_V5
-	select ARCH_HAS_CPUFREQ
 	select ARCH_REQUIRE_GPIOLIB
 	select CPU_FEROCEON
 	select KIRKWOOD_CLK
@@ -97,6 +94,4 @@ config MACH_KIRKWOOD
 	  Say 'Y' here if you want your kernel to support boards based
 	  on the Marvell Kirkwood device tree.
 
-endmenu
-
 endif

arch/arm/mach-nomadik/Kconfig

-config ARCH_NOMADIK
+menuconfig ARCH_NOMADIK
 	bool "ST-Ericsson Nomadik"
 	depends on ARCH_MULTI_V5
 	select ARCH_REQUIRE_GPIOLIB
@@ -15,7 +15,6 @@ config ARCH_NOMADIK
 	  Support for the Nomadik platform by ST-Ericsson
 
 if ARCH_NOMADIK
-menu "Nomadik boards"
 
 config MACH_NOMADIK_8815NHK
 	bool "ST 8815 Nomadik Hardware Kit (evaluation board)"
@@ -24,7 +23,6 @@ config MACH_NOMADIK_8815NHK
 	select I2C_ALGOBIT
 	select I2C_NOMADIK
 
-endmenu
 endif
 
 config NOMADIK_8815

arch/arm/mach-omap2/Kconfig

+menu "TI OMAP/AM/DM/DRA Family"
+	depends on ARCH_MULTI_V6 || ARCH_MULTI_V7
+
 config ARCH_OMAP
 	bool
 
@@ -28,7 +31,6 @@ config ARCH_OMAP4
 	select ARM_CPU_SUSPEND if PM
 	select ARM_ERRATA_720789
 	select ARM_GIC
-	select CACHE_L2X0
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
 	select OMAP_INTERCONNECT
@@ -80,7 +82,6 @@ config SOC_DRA7XX
 config ARCH_OMAP2PLUS
 	bool
 	select ARCH_HAS_BANDGAP
-	select ARCH_HAS_CPUFREQ
 	select ARCH_HAS_HOLES_MEMORYMODEL
 	select ARCH_OMAP
 	select ARCH_REQUIRE_GPIOLIB
@@ -343,3 +344,5 @@ config OMAP4_ERRATA_I688
 endmenu
 
 endif
+
+endmenu

arch/arm/mach-omap2/common.h

@@ -91,7 +91,14 @@ extern void omap3_sync32k_timer_init(void);
 extern void omap3_secure_sync32k_timer_init(void);
 extern void omap3_gptimer_timer_init(void);
 extern void omap4_local_timer_init(void);
+#ifdef CONFIG_CACHE_L2X0
 int omap_l2_cache_init(void);
+#else
+static inline int omap_l2_cache_init(void)
+{
+	return 0;
+}
+#endif
 extern void omap5_realtime_timer_init(void);
 
 void omap2420_init_early(void);

arch/arm/mach-prima2/Kconfig

-config ARCH_SIRF
+menuconfig ARCH_SIRF
 	bool "CSR SiRF" if ARCH_MULTI_V7
 	select ARCH_HAS_RESET_CONTROLLER
 	select ARCH_REQUIRE_GPIOLIB
@@ -11,7 +11,7 @@ config ARCH_SIRF
 
 if ARCH_SIRF
 
-menu "CSR SiRF atlas6/primaII/Marco/Polo Specific Features"
+comment "CSR SiRF atlas6/primaII/Marco/Polo Specific Features"
 
 config ARCH_ATLAS6
 	bool "CSR SiRFSoC ATLAS6 ARM Cortex A9 Platform"
@@ -37,8 +37,6 @@ config ARCH_MARCO
 	help
           Support for CSR SiRFSoC ARM Cortex A9 Platform
 
-endmenu
-
 config SIRF_IRQ
 	bool
 

arch/arm/mach-qcom/Kconfig

-config ARCH_QCOM
+menuconfig ARCH_QCOM
 	bool "Qualcomm Support" if ARCH_MULTI_V7
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_GIC
@@ -11,8 +11,6 @@ config ARCH_QCOM
 
 if ARCH_QCOM
 
-menu "Qualcomm SoC Selection"
-
 config ARCH_MSM8X60
 	bool "Enable support for MSM8X60"
 	select CLKSRC_QCOM
@@ -25,8 +23,6 @@ config ARCH_MSM8974
 	bool "Enable support for MSM8974"
 	select HAVE_ARM_ARCH_TIMER
 
-endmenu
-
 config QCOM_SCM
 	bool
 

arch/arm/mach-s3c24xx/Kconfig

@@ -117,7 +117,7 @@ config S3C24XX_SETUP_TS
 	  Compile in platform device definition for Samsung TouchScreen.
 
 config S3C24XX_DMA
-	bool "S3C2410 DMA support"
+	bool "S3C2410 DMA support (deprecated)"
 	select S3C_DMA
 	help
 	  S3C2410 DMA support. This is needed for drivers like sound which

arch/arm/mach-s3c64xx/Kconfig

@@ -18,9 +18,9 @@ config CPU_S3C6410
 	  Enable S3C6410 CPU support
 
 config S3C64XX_PL080
-	bool "S3C64XX DMA using generic PL08x driver"
+	def_bool DMADEVICES
+	select ARM_AMBA
 	select AMBA_PL08X
-	select SAMSUNG_DMADEV
 
 config S3C64XX_SETUP_SDHCI
 	bool

arch/arm/mach-s5p64x0/Kconfig

@@ -9,16 +9,18 @@ if ARCH_S5P64X0
 
 config CPU_S5P6440
 	bool
+	select ARM_AMBA
+	select PL330_DMA if DMADEVICES
 	select S5P_SLEEP if PM
-	select SAMSUNG_DMADEV
 	select SAMSUNG_WAKEMASK if PM
 	help
 	  Enable S5P6440 CPU support
 
 config CPU_S5P6450
 	bool
+	select ARM_AMBA
+	select PL330_DMA if DMADEVICES
 	select S5P_SLEEP if PM
-	select SAMSUNG_DMADEV
 	select SAMSUNG_WAKEMASK if PM
 	help
 	  Enable S5P6450 CPU support

arch/arm/mach-s5pc100/Kconfig

@@ -9,8 +9,9 @@ if ARCH_S5PC100
 
 config CPU_S5PC100
 	bool
+	select ARM_AMBA
+	select PL330_DMA if DMADEVICES
 	select S5P_EXT_INT
-	select SAMSUNG_DMADEV
 	help
 	  Enable S5PC100 CPU support
 

arch/arm/mach-s5pv210/Kconfig

@@ -11,10 +11,11 @@ if ARCH_S5PV210
 
 config CPU_S5PV210
 	bool
+	select ARM_AMBA
+	select PL330_DMA if DMADEVICES
 	select S5P_EXT_INT
 	select S5P_PM if PM
 	select S5P_SLEEP if PM
-	select SAMSUNG_DMADEV
 	help
 	  Enable S5PV210 CPU support
 

arch/arm/mach-shmobile/Kconfig

 config ARCH_SHMOBILE
 	bool
 
-config ARCH_SHMOBILE_MULTI
+menuconfig ARCH_SHMOBILE_MULTI
 	bool "Renesas ARM SoCs" if ARCH_MULTI_V7
 	depends on MMU
 	select ARCH_SHMOBILE
@@ -15,7 +15,7 @@ config ARCH_SHMOBILE_MULTI
 
 if ARCH_SHMOBILE_MULTI
 
-comment "Renesas ARM SoCs System Type"
+#comment "Renesas ARM SoCs System Type"
 
 config ARCH_EMEV2
 	bool "Emma Mobile EV2"
@@ -85,7 +85,6 @@ config ARCH_R8A73A4
 	select CPU_V7
 	select SH_CLK_CPG
 	select RENESAS_IRQC
-	select ARCH_HAS_CPUFREQ
 	select ARCH_HAS_OPP
 	select SYS_SUPPORTS_SH_CMT
 	select SYS_SUPPORTS_SH_TMU
@@ -264,7 +263,6 @@ config MACH_KOELSCH
 config MACH_KZM9G
 	bool "KZM-A9-GT board"
 	depends on ARCH_SH73A0
-	select ARCH_HAS_CPUFREQ
 	select ARCH_HAS_OPP
 	select ARCH_REQUIRE_GPIOLIB
 	select REGULATOR_FIXED_VOLTAGE if REGULATOR

arch/arm/mach-spear/Kconfig

@@ -14,7 +14,6 @@ if PLAT_SPEAR
 config ARCH_SPEAR13XX
 	bool "ST SPEAr13xx"
 	depends on ARCH_MULTI_V7 || PLAT_SPEAR_SINGLE
-	select ARCH_HAS_CPUFREQ
 	select ARM_GIC
 	select GPIO_SPEAR_SPICS
 	select HAVE_ARM_SCU if SMP

arch/arm/mach-sti/Kconfig

 menuconfig ARCH_STI
-	bool "STMicroelectronics Consumer Electronics SOCs with Device Trees" if ARCH_MULTI_V7
+	bool "STMicroelectronics Consumer Electronics SOCs" if ARCH_MULTI_V7
 	select ARM_GIC
 	select ARM_GLOBAL_TIMER
 	select PINCTRL

arch/arm/mach-tegra/Kconfig

-config ARCH_TEGRA
+menuconfig ARCH_TEGRA
 	bool "NVIDIA Tegra" if ARCH_MULTI_V7
-	select ARCH_HAS_CPUFREQ
 	select ARCH_REQUIRE_GPIOLIB
 	select ARCH_SUPPORTS_TRUSTED_FOUNDATIONS
 	select ARM_GIC
@@ -16,8 +15,7 @@ config ARCH_TEGRA
 	help
 	  This enables support for NVIDIA Tegra based systems.
 
-menu "NVIDIA Tegra options"
-	depends on ARCH_TEGRA
+if ARCH_TEGRA
 
 config ARCH_TEGRA_2x_SOC
 	bool "Enable support for Tegra20 family"
@@ -69,4 +67,4 @@ config TEGRA_AHB
 	  which controls AHB bus master arbitration and some
 	  performance parameters(priority, prefech size).
 
-endmenu
+endif

arch/arm/mach-u300/Kconfig

-config ARCH_U300
+menuconfig ARCH_U300
 	bool "ST-Ericsson U300 Series" if ARCH_MULTI_V5
 	depends on MMU
 	select ARCH_REQUIRE_GPIOLIB
@@ -16,8 +16,6 @@ config ARCH_U300
 
 if ARCH_U300
 
-menu "ST-Ericsson AB U300/U335 Platform"
-
 config MACH_U300
 	depends on ARCH_U300
 	bool "U300"
@@ -43,6 +41,4 @@ config MACH_U300_SPIDUMMY
 		you don't need it. Selecting this will activate the
 		SPI framework and ARM PL022 support.
 
-endmenu
-
 endif

arch/arm/mach-ux500/Kconfig

-config ARCH_U8500
+menuconfig ARCH_U8500
 	bool "ST-Ericsson U8500 Series" if ARCH_MULTI_V7
 	depends on MMU
 	select AB8500_CORE
 	select ABX500_CORE
-	select ARCH_HAS_CPUFREQ
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_AMBA
 	select ARM_ERRATA_754322
@@ -34,8 +33,6 @@ config UX500_SOC_DB8500
 	select REGULATOR
 	select REGULATOR_DB8500_PRCMU
 
-menu "Ux500 target platform (boards)"
-
 config MACH_MOP500
 	bool "U8500 Development platform, MOP500 versions"
 	select I2C
@@ -68,8 +65,6 @@ config UX500_AUTO_PLATFORM
 	  a working kernel. If everything else is disabled, this
 	  automatically enables MACH_MOP500.
 
-endmenu
-
 config UX500_DEBUG_UART
 	int "Ux500 UART to use for low-level debug"
 	default 2

arch/arm/mach-vexpress/Kconfig

-config ARCH_VEXPRESS
+menuconfig ARCH_VEXPRESS
 	bool "ARM Ltd. Versatile Express family" if ARCH_MULTI_V7
 	select ARCH_REQUIRE_GPIOLIB
 	select ARCH_SUPPORTS_BIG_ENDIAN
@@ -37,8 +37,7 @@ config ARCH_VEXPRESS
 	  platforms. The traditional (ATAGs) boot method is not usable on
 	  these boards with this option.
 
-menu "Versatile Express platform type"
-	depends on ARCH_VEXPRESS
+if ARCH_VEXPRESS
 
 config ARCH_VEXPRESS_CORTEX_A5_A9_ERRATA
 	bool "Enable A5 and A9 only errata work-arounds"
@@ -65,7 +64,6 @@ config ARCH_VEXPRESS_DCSCB
 
 config ARCH_VEXPRESS_SPC
 	bool "Versatile Express Serial Power Controller (SPC)"
-	select ARCH_HAS_CPUFREQ
 	select ARCH_HAS_OPP
 	select PM_OPP
 	help
@@ -83,4 +81,4 @@ config ARCH_VEXPRESS_TC2_PM
 	  Support for CPU and cluster power management on Versatile Express
 	  with a TC2 (A15x2 A7x3) big.LITTLE core tile.
 
-endmenu
+endif

arch/arm/mach-vt8500/Kconfig

 config ARCH_VT8500
 	bool
-	select ARCH_HAS_CPUFREQ
 	select ARCH_REQUIRE_GPIOLIB
 	select CLKDEV_LOOKUP
 	select VT8500_TIMER

arch/arm/mach-zynq/Kconfig

 config ARCH_ZYNQ
 	bool "Xilinx Zynq ARM Cortex A9 Platform" if ARCH_MULTI_V7
-	select ARCH_HAS_CPUFREQ
 	select ARCH_HAS_OPP
 	select ARCH_SUPPORTS_BIG_ENDIAN
 	select ARM_AMBA

arch/arm/plat-samsung/Kconfig

@@ -35,27 +35,15 @@ config SAMSUNG_PM
 	  Base platform power management code for samsung code
 
 if PLAT_SAMSUNG
+menu "Samsung Common options"
 
 # boot configurations
 
 comment "Boot options"
 
-config S3C_BOOT_ERROR_RESET
-	bool "S3C Reboot on decompression error"
-	help
-	  Say y here to use the watchdog to reset the system if the
-	  kernel decompressor detects an error during decompression.
-
-config S3C_BOOT_UART_FORCE_FIFO
-       bool "Force UART FIFO on during boot process"
-       default y
-       help
-         Say Y here to force the UART FIFOs on during the kernel
-	 uncompressor
-
-
 config S3C_LOWLEVEL_UART_PORT
 	int "S3C UART to use for low-level messages"
+	depends on ARCH_S3C64XX
 	default 0
 	help
 	  Choice of which UART port to use for the low-level messages,
@@ -407,17 +395,16 @@ config SAMSUNG_PM_GPIO
 	  Include legacy GPIO power management code for platforms not using
 	  pinctrl-samsung driver.
 
-endif
-
 config SAMSUNG_DMADEV
-	bool
-	select ARM_AMBA
+	bool "Use legacy Samsung DMA abstraction"
+	depends on CPU_S5PV210 || CPU_S5PC100 || ARCH_S5P64X0 || ARCH_S3C64XX
 	select DMADEVICES
-	select PL330_DMA if (ARCH_EXYNOS5 || ARCH_EXYNOS4 || CPU_S5PV210 || CPU_S5PC100 || \
-					CPU_S5P6450 || CPU_S5P6440)
+	default y
 	help
 	  Use DMA device engine for PL330 DMAC.
 
+endif
+
 config S5P_DEV_MFC
 	bool
 	help
@@ -503,4 +490,5 @@ config DEBUG_S3C_UART
 	default "2" if DEBUG_S3C_UART2
 	default "3" if DEBUG_S3C_UART3
 
+endmenu
 endif

arch/arm64/Kconfig

 config ARM64
 	def_bool y
 	select ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE
-	select ARCH_USE_CMPXCHG_LOCKREF
+	select ARCH_HAS_OPP
 	select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST
+	select ARCH_USE_CMPXCHG_LOCKREF
 	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select ARCH_WANT_COMPAT_IPC_PARSE_VERSION
 	select ARCH_WANT_FRAME_POINTERS

arch/arm64/boot/dts/apm-mustang.dts

@@ -24,3 +24,7 @@ memory {
 		reg = < 0x1 0x00000000 0x0 0x80000000 >; /* Updated by bootloader */
 	};
 };
+
+&serial0 {
+	status = "ok";
+};

arch/arm64/boot/dts/apm-storm.dtsi

@@ -273,8 +273,9 @@ rtcclk: rtcclk@17000000 {
 		};
 
 		serial0: serial@1c020000 {
+			status = "disabled";
 			device_type = "serial";
-			compatible = "ns16550";
+			compatible = "ns16550a";
 			reg = <0 0x1c020000 0x0 0x1000>;
 			reg-shift = <2>;
 			clock-frequency = <10000000>; /* Updated by bootloader */
@@ -282,6 +283,39 @@ serial0: serial@1c020000 {
 			interrupts = <0x0 0x4c 0x4>;
 		};
 
+		serial1: serial@1c021000 {
+			status = "disabled";
+			device_type = "serial";
+			compatible = "ns16550a";
+			reg = <0 0x1c021000 0x0 0x1000>;
+			reg-shift = <2>;
+			clock-frequency = <10000000>; /* Updated by bootloader */
+			interrupt-parent = <&gic>;
+			interrupts = <0x0 0x4d 0x4>;
+		};
+
+		serial2: serial@1c022000 {
+			status = "disabled";
+			device_type = "serial";
+			compatible = "ns16550a";
+			reg = <0 0x1c022000 0x0 0x1000>;
+			reg-shift = <2>;
+			clock-frequency = <10000000>; /* Updated by bootloader */
+			interrupt-parent = <&gic>;
+			interrupts = <0x0 0x4e 0x4>;
+		};
+
+		serial3: serial@1c023000 {
+			status = "disabled";
+			device_type = "serial";
+			compatible = "ns16550a";
+			reg = <0 0x1c023000 0x0 0x1000>;
+			reg-shift = <2>;
+			clock-frequency = <10000000>; /* Updated by bootloader */
+			interrupt-parent = <&gic>;
+			interrupts = <0x0 0x4f 0x4>;
+		};
+
 		phy1: phy@1f21a000 {
 			compatible = "apm,xgene-phy";
 			reg = <0x0 0x1f21a000 0x0 0x100>;

arch/arm64/configs/defconfig

@@ -6,9 +6,18 @@ CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_TASKSTATS=y
+CONFIG_TASK_DELAY_ACCT=y
+CONFIG_TASK_XACCT=y
+CONFIG_TASK_IO_ACCOUNTING=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
+CONFIG_RESOURCE_COUNTERS=y
+CONFIG_MEMCG=y
+CONFIG_MEMCG_SWAP=y
+CONFIG_MEMCG_KMEM=y
+CONFIG_CGROUP_HUGETLB=y
 # CONFIG_UTS_NS is not set
 # CONFIG_IPC_NS is not set
 # CONFIG_PID_NS is not set
@@ -27,6 +36,7 @@ CONFIG_ARCH_VEXPRESS=y
 CONFIG_ARCH_XGENE=y
 CONFIG_SMP=y
 CONFIG_PREEMPT=y
+CONFIG_KSM=y
 CONFIG_TRANSPARENT_HUGEPAGE=y
 CONFIG_CMA=y
 CONFIG_CMDLINE="console=ttyAMA0"
@@ -45,6 +55,7 @@ CONFIG_IP_PNP_BOOTP=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_DEVTMPFS=y
 CONFIG_DMA_CMA=y
+CONFIG_BLK_DEV_LOOP=y
 CONFIG_VIRTIO_BLK=y
 # CONFIG_SCSI_PROC_FS is not set
 CONFIG_BLK_DEV_SD=y
@@ -53,6 +64,7 @@ CONFIG_ATA=y
 CONFIG_PATA_PLATFORM=y
 CONFIG_PATA_OF_PLATFORM=y
 CONFIG_NETDEVICES=y
+CONFIG_TUN=y
 CONFIG_SMC91X=y
 CONFIG_SMSC911X=y
 # CONFIG_WLAN is not set
@@ -85,6 +97,8 @@ CONFIG_EXT3_FS=y
 # CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
 # CONFIG_EXT3_FS_XATTR is not set
 CONFIG_EXT4_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_FANOTIFY_ACCESS_PERMISSIONS=y
 CONFIG_FUSE_FS=y
 CONFIG_CUSE=y
 CONFIG_VFAT_FS=y
@@ -104,6 +118,7 @@ CONFIG_DEBUG_KERNEL=y
 CONFIG_LOCKUP_DETECTOR=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_FTRACE is not set
+CONFIG_SECURITY=y
 CONFIG_CRYPTO_ANSI_CPRNG=y
 CONFIG_ARM64_CRYPTO=y
 CONFIG_CRYPTO_SHA1_ARM64_CE=y

arch/arm64/crypto/ghash-ce-core.S

@@ -3,14 +3,6 @@
  *
  * Copyright (C) 2014 Linaro Ltd. <ard.biesheuvel@linaro.org>
  *
- * Based on arch/x86/crypto/ghash-pmullni-intel_asm.S
- *
- * Copyright (c) 2009 Intel Corp.
- *   Author: Huang Ying <ying.huang@intel.com>
- *           Vinodh Gopal
- *           Erdinc Ozturk
- *           Deniz Karakoyunlu
- *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License version 2 as published
  * by the Free Software Foundation.
@@ -19,13 +11,15 @@
 #include <linux/linkage.h>
 #include <asm/assembler.h>
 
-	DATA	.req	v0
-	SHASH	.req	v1
-	IN1	.req	v2
+	SHASH	.req	v0
+	SHASH2	.req	v1
 	T1	.req	v2
 	T2	.req	v3
-	T3	.req	v4
-	VZR	.req	v5
+	MASK	.req	v4
+	XL	.req	v5
+	XM	.req	v6
+	XH	.req	v7
+	IN1	.req	v7
 
 	.text
 	.arch		armv8-a+crypto
@@ -35,61 +29,51 @@
 	 *			   struct ghash_key const *k, const char *head)
 	 */
 ENTRY(pmull_ghash_update)
-	ld1		{DATA.16b}, [x1]
 	ld1		{SHASH.16b}, [x3]
-	eor		VZR.16b, VZR.16b, VZR.16b
+	ld1		{XL.16b}, [x1]
+	movi		MASK.16b, #0xe1
+	ext		SHASH2.16b, SHASH.16b, SHASH.16b, #8
+	shl		MASK.2d, MASK.2d, #57
+	eor		SHASH2.16b, SHASH2.16b, SHASH.16b
 
 	/* do the head block first, if supplied */
 	cbz		x4, 0f
-	ld1		{IN1.2d}, [x4]
+	ld1		{T1.2d}, [x4]
 	b		1f
 
-0:	ld1		{IN1.2d}, [x2], #16
+0:	ld1		{T1.2d}, [x2], #16
 	sub		w0, w0, #1
-1:	ext		IN1.16b, IN1.16b, IN1.16b, #8
-CPU_LE(	rev64		IN1.16b, IN1.16b	)
-	eor		DATA.16b, DATA.16b, IN1.16b
 
-	/* multiply DATA by SHASH in GF(2^128) */
-	ext		T2.16b, DATA.16b, DATA.16b, #8
-	ext		T3.16b, SHASH.16b, SHASH.16b, #8
-	eor		T2.16b, T2.16b, DATA.16b
-	eor		T3.16b, T3.16b, SHASH.16b
+1:	/* multiply XL by SHASH in GF(2^128) */
+CPU_LE(	rev64		T1.16b, T1.16b	)
 
-	pmull2		T1.1q, SHASH.2d, DATA.2d	// a1 * b1
-	pmull		DATA.1q, SHASH.1d, DATA.1d	// a0 * b0
-	pmull		T2.1q, T2.1d, T3.1d		// (a1 + a0)(b1 + b0)
-	eor		T2.16b, T2.16b, T1.16b		// (a0 * b1) + (a1 * b0)
-	eor		T2.16b, T2.16b, DATA.16b
+	ext		T2.16b, XL.16b, XL.16b, #8
+	ext		IN1.16b, T1.16b, T1.16b, #8
+	eor		T1.16b, T1.16b, T2.16b
+	eor		XL.16b, XL.16b, IN1.16b
 
-	ext		T3.16b, VZR.16b, T2.16b, #8
-	ext		T2.16b, T2.16b, VZR.16b, #8
-	eor		DATA.16b, DATA.16b, T3.16b
-	eor		T1.16b, T1.16b, T2.16b	// <T1:DATA> is result of
-						// carry-less multiplication
+	pmull2		XH.1q, SHASH.2d, XL.2d		// a1 * b1
+	eor		T1.16b, T1.16b, XL.16b
+	pmull		XL.1q, SHASH.1d, XL.1d		// a0 * b0
+	pmull		XM.1q, SHASH2.1d, T1.1d		// (a1 + a0)(b1 + b0)
 
-	/* first phase of the reduction */
-	shl		T3.2d, DATA.2d, #1
-	eor		T3.16b, T3.16b, DATA.16b
-	shl		T3.2d, T3.2d, #5
-	eor		T3.16b, T3.16b, DATA.16b
-	shl		T3.2d, T3.2d, #57
-	ext		T2.16b, VZR.16b, T3.16b, #8
-	ext		T3.16b, T3.16b, VZR.16b, #8
-	eor		DATA.16b, DATA.16b, T2.16b
-	eor		T1.16b, T1.16b, T3.16b
+	ext		T1.16b, XL.16b, XH.16b, #8
+	eor		T2.16b, XL.16b, XH.16b
+	eor		XM.16b, XM.16b, T1.16b
+	eor		XM.16b, XM.16b, T2.16b
+	pmull		T2.1q, XL.1d, MASK.1d
 
-	/* second phase of the reduction */
-	ushr		T2.2d, DATA.2d, #5
-	eor		T2.16b, T2.16b, DATA.16b
-	ushr		T2.2d, T2.2d, #1
-	eor		T2.16b, T2.16b, DATA.16b
-	ushr		T2.2d, T2.2d, #1
-	eor		T1.16b, T1.16b, T2.16b
-	eor		DATA.16b, DATA.16b, T1.16b
+	mov		XH.d[0], XM.d[1]
+	mov		XM.d[1], XL.d[0]
+
+	eor		XL.16b, XM.16b, T2.16b
+	ext		T2.16b, XL.16b, XL.16b, #8
+	pmull		XL.1q, XL.1d, MASK.1d
+	eor		T2.16b, T2.16b, XH.16b
+	eor		XL.16b, XL.16b, T2.16b
 
 	cbnz		w0, 0b
 
-	st1		{DATA.16b}, [x1]
+	st1		{XL.16b}, [x1]
 	ret
 ENDPROC(pmull_ghash_update)

arch/arm64/crypto/ghash-ce-glue.c

@@ -67,11 +67,12 @@ static int ghash_update(struct shash_desc *desc, const u8 *src,
 		blocks = len / GHASH_BLOCK_SIZE;
 		len %= GHASH_BLOCK_SIZE;
 
-		kernel_neon_begin_partial(6);
+		kernel_neon_begin_partial(8);
 		pmull_ghash_update(blocks, ctx->digest, src, key,
 				   partial ? ctx->buf : NULL);
 		kernel_neon_end();
 		src += blocks * GHASH_BLOCK_SIZE;
+		partial = 0;
 	}
 	if (len)
 		memcpy(ctx->buf + partial, src, len);
@@ -88,7 +89,7 @@ static int ghash_final(struct shash_desc *desc, u8 *dst)
 
 		memset(ctx->buf + partial, 0, GHASH_BLOCK_SIZE - partial);
 
-		kernel_neon_begin_partial(6);
+		kernel_neon_begin_partial(8);
 		pmull_ghash_update(1, ctx->digest, ctx->buf, key, NULL);
 		kernel_neon_end();
 	}

arch/arm64/include/asm/Kbuild

@@ -30,7 +30,6 @@ generic-y += msgbuf.h
 generic-y += mutex.h
 generic-y += pci.h
 generic-y += poll.h
-generic-y += posix_types.h
 generic-y += preempt.h
 generic-y += resource.h
 generic-y += rwsem.h

arch/arm64/include/asm/dma-mapping.h

@@ -26,8 +26,6 @@
 #include <xen/xen.h>
 #include <asm/xen/hypervisor.h>
 
-#define ARCH_HAS_DMA_GET_REQUIRED_MASK
-
 #define DMA_ERROR_CODE	(~(dma_addr_t)0)
 extern struct dma_map_ops *dma_ops;
 extern struct dma_map_ops coherent_swiotlb_dma_ops;

arch/arm64/include/asm/pgtable.h

@@ -246,7 +246,7 @@ static inline pmd_t pte_pmd(pte_t pte)
 #define pmd_mkwrite(pmd)	pte_pmd(pte_mkwrite(pmd_pte(pmd)))
 #define pmd_mkdirty(pmd)	pte_pmd(pte_mkdirty(pmd_pte(pmd)))
 #define pmd_mkyoung(pmd)	pte_pmd(pte_mkyoung(pmd_pte(pmd)))
-#define pmd_mknotpresent(pmd)	(__pmd(pmd_val(pmd) &= ~PMD_TYPE_MASK))
+#define pmd_mknotpresent(pmd)	(__pmd(pmd_val(pmd) & ~PMD_TYPE_MASK))
 
 #define __HAVE_ARCH_PMD_WRITE
 #define pmd_write(pmd)		pte_write(pmd_pte(pmd))

arch/arm64/include/uapi/asm/posix_types.h

+#ifndef __ASM_POSIX_TYPES_H
+#define __ASM_POSIX_TYPES_H
+
+typedef unsigned short __kernel_old_uid_t;
+typedef unsigned short __kernel_old_gid_t;
+#define __kernel_old_uid_t __kernel_old_uid_t
+
+#include <asm-generic/posix_types.h>
+
+#endif /*  __ASM_POSIX_TYPES_H */

arch/arm64/include/uapi/asm/sigcontext.h

@@ -58,7 +58,7 @@ struct fpsimd_context {
 
 struct esr_context {
 	struct _aarch64_ctx head;
-	u64 esr;
+	__u64 esr;
 };
 
 #endif /* _UAPI__ASM_SIGCONTEXT_H */

arch/arm64/kernel/entry-ftrace.S

@@ -205,7 +205,7 @@ ENDPROC(ftrace_graph_caller)
  *
  * Run ftrace_return_to_handler() before going back to parent.
  * @fp is checked against the value passed by ftrace_graph_caller()
- * only when CONFIG_FUNCTION_GRAPH_FP_TEST is enabled.
+ * only when CONFIG_HAVE_FUNCTION_GRAPH_FP_TEST is enabled.
  */
 ENTRY(return_to_handler)
 	str	x0, [sp, #-16]!

arch/arm64/kernel/entry.S

@@ -279,7 +279,6 @@ el1_sp_pc:
 	 */
 	mrs	x0, far_el1
 	enable_dbg
-	mov	x1, x25
 	mov	x2, sp
 	b	do_sp_pc_abort
 el1_undef:

arch/arm64/kernel/ptrace.c

@@ -655,11 +655,16 @@ static int compat_gpr_get(struct task_struct *target,
 			reg = task_pt_regs(target)->regs[idx];
 		}
 
-		ret = copy_to_user(ubuf, &reg, sizeof(reg));
-		if (ret)
-			break;
-
-		ubuf += sizeof(reg);
+		if (kbuf) {
+			memcpy(kbuf, &reg, sizeof(reg));
+			kbuf += sizeof(reg);
+		} else {
+			ret = copy_to_user(ubuf, &reg, sizeof(reg));
+			if (ret)
+				break;
+
+			ubuf += sizeof(reg);
+		}
 	}
 
 	return ret;
@@ -689,11 +694,16 @@ static int compat_gpr_set(struct task_struct *target,
 		unsigned int idx = start + i;
 		compat_ulong_t reg;
 
-		ret = copy_from_user(&reg, ubuf, sizeof(reg));
-		if (ret)
-			return ret;
+		if (kbuf) {
+			memcpy(&reg, kbuf, sizeof(reg));
+			kbuf += sizeof(reg);
+		} else {
+			ret = copy_from_user(&reg, ubuf, sizeof(reg));
+			if (ret)
+				return ret;
 
-		ubuf += sizeof(reg);
+			ubuf += sizeof(reg);
+		}
 
 		switch (idx) {
 		case 15:
@@ -827,6 +837,7 @@ static int compat_ptrace_write_user(struct task_struct *tsk, compat_ulong_t off,
 				    compat_ulong_t val)
 {
 	int ret;
+	mm_segment_t old_fs = get_fs();
 
 	if (off & 3 || off >= COMPAT_USER_SZ)
 		return -EIO;
@@ -834,10 +845,13 @@ static int compat_ptrace_write_user(struct task_struct *tsk, compat_ulong_t off,
 	if (off >= sizeof(compat_elf_gregset_t))
 		return 0;
 
+	set_fs(KERNEL_DS);
 	ret = copy_regset_from_user(tsk, &user_aarch32_view,
 				    REGSET_COMPAT_GPR, off,
 				    sizeof(compat_ulong_t),
 				    &val);
+	set_fs(old_fs);
+
 	return ret;
 }
 

arch/arm64/mm/init.c

@@ -71,7 +71,7 @@ static void __init zone_sizes_init(unsigned long min, unsigned long max)
 	/* 4GB maximum for 32-bit only capable devices */
 	if (IS_ENABLED(CONFIG_ZONE_DMA)) {
 		unsigned long max_dma_phys =
-			(unsigned long)dma_to_phys(NULL, DMA_BIT_MASK(32) + 1);
+			(unsigned long)(dma_to_phys(NULL, DMA_BIT_MASK(32)) + 1);
 		max_dma = max(min, min(max, max_dma_phys >> PAGE_SHIFT));
 		zone_size[ZONE_DMA] = max_dma - min;
 	}
@@ -126,6 +126,8 @@ static void arm64_memory_present(void)
 
 void __init arm64_memblock_init(void)
 {
+	phys_addr_t dma_phys_limit = 0;
+
 	/* Register the kernel text, kernel data and initrd with memblock */
 	memblock_reserve(__pa(_text), _end - _text);
 #ifdef CONFIG_BLK_DEV_INITRD
@@ -141,7 +143,11 @@ void __init arm64_memblock_init(void)
 	memblock_reserve(__pa(idmap_pg_dir), IDMAP_DIR_SIZE);
 
 	early_init_fdt_scan_reserved_mem();
-	dma_contiguous_reserve(0);
+
+	/* 4GB maximum for 32-bit only capable devices */
+	if (IS_ENABLED(CONFIG_ZONE_DMA))
+		dma_phys_limit = dma_to_phys(NULL, DMA_BIT_MASK(32)) + 1;
+	dma_contiguous_reserve(dma_phys_limit);
 
 	memblock_allow_resize();
 	memblock_dump_all();

arch/ia64/hp/common/sba_iommu.c

@@ -242,7 +242,7 @@ struct ioc {
 	struct pci_dev	*sac_only_dev;
 };
 
-static struct ioc *ioc_list;
+static struct ioc *ioc_list, *ioc_found;
 static int reserve_sba_gart = 1;
 
 static SBA_INLINE void sba_mark_invalid(struct ioc *, dma_addr_t, size_t);
@@ -1809,20 +1809,13 @@ static struct ioc_iommu ioc_iommu_info[] __initdata = {
 	{ SX2000_IOC_ID, "sx2000", NULL },
 };
 
-static struct ioc *
-ioc_init(unsigned long hpa, void *handle)
+static void ioc_init(unsigned long hpa, struct ioc *ioc)
 {
-	struct ioc *ioc;
 	struct ioc_iommu *info;
 
-	ioc = kzalloc(sizeof(*ioc), GFP_KERNEL);
-	if (!ioc)
-		return NULL;
-
 	ioc->next = ioc_list;
 	ioc_list = ioc;
 
-	ioc->handle = handle;
 	ioc->ioc_hpa = ioremap(hpa, 0x1000);
 
 	ioc->func_id = READ_REG(ioc->ioc_hpa + IOC_FUNC_ID);
@@ -1863,8 +1856,6 @@ ioc_init(unsigned long hpa, void *handle)
 		"%s %d.%d HPA 0x%lx IOVA space %dMb at 0x%lx\n",
 		ioc->name, (ioc->rev >> 4) & 0xF, ioc->rev & 0xF,
 		hpa, ioc->iov_size >> 20, ioc->ibase);
-
-	return ioc;
 }
 
 
@@ -2031,22 +2022,21 @@ sba_map_ioc_to_node(struct ioc *ioc, acpi_handle handle)
 #endif
 }
 
-static int
-acpi_sba_ioc_add(struct acpi_device *device,
-		 const struct acpi_device_id *not_used)
+static void acpi_sba_ioc_add(struct ioc *ioc)
 {
-	struct ioc *ioc;
+	acpi_handle handle = ioc->handle;
 	acpi_status status;
 	u64 hpa, length;
 	struct acpi_device_info *adi;
 
-	status = hp_acpi_csr_space(device->handle, &hpa, &length);
+	ioc_found = ioc->next;
+	status = hp_acpi_csr_space(handle, &hpa, &length);
 	if (ACPI_FAILURE(status))
-		return 1;
+		goto err;
 
-	status = acpi_get_object_info(device->handle, &adi);
+	status = acpi_get_object_info(handle, &adi);
 	if (ACPI_FAILURE(status))
-		return 1;
+		goto err;
 
 	/*
 	 * For HWP0001, only SBA appears in ACPI namespace.  It encloses the PCI
@@ -2067,13 +2057,13 @@ acpi_sba_ioc_add(struct acpi_device *device,
 	if (!iovp_shift)
 		iovp_shift = 12;
 
-	ioc = ioc_init(hpa, device->handle);
-	if (!ioc)
-		return 1;
-
+	ioc_init(hpa, ioc);
 	/* setup NUMA node association */
-	sba_map_ioc_to_node(ioc, device->handle);
-	return 0;
+	sba_map_ioc_to_node(ioc, handle);
+	return;
+
+ err:
+	kfree(ioc);
 }
 
 static const struct acpi_device_id hp_ioc_iommu_device_ids[] = {
@@ -2081,9 +2071,26 @@ static const struct acpi_device_id hp_ioc_iommu_device_ids[] = {
 	{"HWP0004", 0},
 	{"", 0},
 };
+
+static int acpi_sba_ioc_attach(struct acpi_device *device,
+			       const struct acpi_device_id *not_used)
+{
+	struct ioc *ioc;
+
+	ioc = kzalloc(sizeof(*ioc), GFP_KERNEL);
+	if (!ioc)
+		return -ENOMEM;
+
+	ioc->next = ioc_found;
+	ioc_found = ioc;
+	ioc->handle = device->handle;
+	return 1;
+}
+
+
 static struct acpi_scan_handler acpi_sba_ioc_handler = {
 	.ids	= hp_ioc_iommu_device_ids,
-	.attach	= acpi_sba_ioc_add,
+	.attach	= acpi_sba_ioc_attach,
 };
 
 static int __init acpi_sba_ioc_init_acpi(void)
@@ -2118,9 +2125,12 @@ sba_init(void)
 #endif
 
 	/*
-	 * ioc_list should be populated by the acpi_sba_ioc_handler's .attach()
+	 * ioc_found should be populated by the acpi_sba_ioc_handler's .attach()
 	 * routine, but that only happens if acpi_scan_init() has already run.
 	 */
+	while (ioc_found)
+		acpi_sba_ioc_add(ioc_found);
+
 	if (!ioc_list) {
 #ifdef CONFIG_IA64_GENERIC
 		/*

arch/s390/configs/default_defconfig

@@ -45,7 +45,8 @@ CONFIG_SOLARIS_X86_PARTITION=y
 CONFIG_UNIXWARE_DISKLABEL=y
 CONFIG_CFQ_GROUP_IOSCHED=y
 CONFIG_DEFAULT_DEADLINE=y
-CONFIG_MARCH_Z9_109=y
+CONFIG_MARCH_Z196=y
+CONFIG_TUNE_ZEC12=y
 CONFIG_NR_CPUS=256
 CONFIG_PREEMPT=y
 CONFIG_HZ_100=y
@@ -240,7 +241,6 @@ CONFIG_IP_VS_PE_SIP=m
 CONFIG_NF_CONNTRACK_IPV4=m
 # CONFIG_NF_CONNTRACK_PROC_COMPAT is not set
 CONFIG_NF_TABLES_IPV4=m
-CONFIG_NFT_REJECT_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
 CONFIG_NF_TABLES_ARP=m
@@ -456,6 +456,7 @@ CONFIG_TN3270_FS=y
 CONFIG_WATCHDOG=y
 CONFIG_WATCHDOG_NOWAYOUT=y
 CONFIG_SOFT_WATCHDOG=m
+CONFIG_DIAG288_WATCHDOG=m
 # CONFIG_HID is not set
 # CONFIG_USB_SUPPORT is not set
 CONFIG_INFINIBAND=m

arch/s390/configs/gcov_defconfig

@@ -45,7 +45,8 @@ CONFIG_SOLARIS_X86_PARTITION=y
 CONFIG_UNIXWARE_DISKLABEL=y
 CONFIG_CFQ_GROUP_IOSCHED=y
 CONFIG_DEFAULT_DEADLINE=y
-CONFIG_MARCH_Z9_109=y
+CONFIG_MARCH_Z196=y
+CONFIG_TUNE_ZEC12=y
 CONFIG_NR_CPUS=256
 CONFIG_HZ_100=y
 CONFIG_MEMORY_HOTPLUG=y
@@ -238,7 +239,6 @@ CONFIG_IP_VS_PE_SIP=m
 CONFIG_NF_CONNTRACK_IPV4=m
 # CONFIG_NF_CONNTRACK_PROC_COMPAT is not set
 CONFIG_NF_TABLES_IPV4=m
-CONFIG_NFT_REJECT_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
 CONFIG_NF_TABLES_ARP=m
@@ -453,6 +453,7 @@ CONFIG_TN3270_FS=y
 CONFIG_WATCHDOG=y
 CONFIG_WATCHDOG_NOWAYOUT=y
 CONFIG_SOFT_WATCHDOG=m
+CONFIG_DIAG288_WATCHDOG=m
 # CONFIG_HID is not set
 # CONFIG_USB_SUPPORT is not set
 CONFIG_INFINIBAND=m

arch/s390/configs/performance_defconfig

@@ -43,7 +43,8 @@ CONFIG_SOLARIS_X86_PARTITION=y
 CONFIG_UNIXWARE_DISKLABEL=y
 CONFIG_CFQ_GROUP_IOSCHED=y
 CONFIG_DEFAULT_DEADLINE=y
-CONFIG_MARCH_Z9_109=y
+CONFIG_MARCH_Z196=y
+CONFIG_TUNE_ZEC12=y
 CONFIG_NR_CPUS=256
 CONFIG_HZ_100=y
 CONFIG_MEMORY_HOTPLUG=y
@@ -236,7 +237,6 @@ CONFIG_IP_VS_PE_SIP=m
 CONFIG_NF_CONNTRACK_IPV4=m
 # CONFIG_NF_CONNTRACK_PROC_COMPAT is not set
 CONFIG_NF_TABLES_IPV4=m
-CONFIG_NFT_REJECT_IPV4=m
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
 CONFIG_NFT_CHAIN_NAT_IPV4=m
 CONFIG_NF_TABLES_ARP=m
@@ -451,6 +451,7 @@ CONFIG_TN3270_FS=y
 CONFIG_WATCHDOG=y
 CONFIG_WATCHDOG_NOWAYOUT=y
 CONFIG_SOFT_WATCHDOG=m
+CONFIG_DIAG288_WATCHDOG=m
 # CONFIG_HID is not set
 # CONFIG_USB_SUPPORT is not set
 CONFIG_INFINIBAND=m

arch/s390/configs/zfcpdump_defconfig

@@ -8,7 +8,8 @@ CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_IBM_PARTITION=y
 CONFIG_DEFAULT_DEADLINE=y
-CONFIG_MARCH_Z9_109=y
+CONFIG_MARCH_Z196=y
+CONFIG_TUNE_ZEC12=y
 # CONFIG_COMPAT is not set
 CONFIG_NR_CPUS=2
 # CONFIG_HOTPLUG_CPU is not set

arch/s390/defconfig

@@ -135,8 +135,8 @@ CONFIG_PROVE_LOCKING=y
 CONFIG_LOCK_STAT=y
 CONFIG_DEBUG_LOCKDEP=y
 CONFIG_DEBUG_ATOMIC_SLEEP=y
-CONFIG_DEBUG_WRITECOUNT=y
 CONFIG_DEBUG_LIST=y
+CONFIG_DEBUG_PI_LIST=y
 CONFIG_DEBUG_SG=y
 CONFIG_DEBUG_NOTIFIERS=y
 CONFIG_PROVE_RCU=y
@@ -199,4 +199,10 @@ CONFIG_CRYPTO_SHA512_S390=m
 CONFIG_CRYPTO_DES_S390=m
 CONFIG_CRYPTO_AES_S390=m
 CONFIG_CRC7=m
+# CONFIG_XZ_DEC_X86 is not set
+# CONFIG_XZ_DEC_POWERPC is not set
+# CONFIG_XZ_DEC_IA64 is not set
+# CONFIG_XZ_DEC_ARM is not set
+# CONFIG_XZ_DEC_ARMTHUMB is not set
+# CONFIG_XZ_DEC_SPARC is not set
 CONFIG_CMM=m

arch/s390/include/asm/mmu_context.h

@@ -33,10 +33,9 @@ static inline int init_new_context(struct task_struct *tsk,
 
 static inline void set_user_asce(struct mm_struct *mm)
 {
-	pgd_t *pgd = mm->pgd;
-
-	S390_lowcore.user_asce = mm->context.asce_bits | __pa(pgd);
-	set_fs(current->thread.mm_segment);
+	S390_lowcore.user_asce = mm->context.asce_bits | __pa(mm->pgd);
+	if (current->thread.mm_segment.ar4)
+		__ctl_load(S390_lowcore.user_asce, 7, 7);
 	set_cpu_flag(CIF_ASCE);
 }
 
@@ -70,12 +69,11 @@ static inline void switch_mm(struct mm_struct *prev, struct mm_struct *next,
 	/* Clear old ASCE by loading the kernel ASCE. */
 	__ctl_load(S390_lowcore.kernel_asce, 1, 1);
 	__ctl_load(S390_lowcore.kernel_asce, 7, 7);
-	/* Delay loading of the new ASCE to control registers CR1 & CR7 */
-	set_cpu_flag(CIF_ASCE);
 	atomic_inc(&next->context.attach_count);
 	atomic_dec(&prev->context.attach_count);
 	if (MACHINE_HAS_TLB_LC)
 		cpumask_clear_cpu(cpu, &prev->context.cpu_attach_mask);
+	S390_lowcore.user_asce = next->context.asce_bits | __pa(next->pgd);
 }
 
 #define finish_arch_post_lock_switch finish_arch_post_lock_switch
@@ -84,17 +82,18 @@ static inline void finish_arch_post_lock_switch(void)
 	struct task_struct *tsk = current;
 	struct mm_struct *mm = tsk->mm;
 
-	if (!mm)
-		return;
-	preempt_disable();
-	while (atomic_read(&mm->context.attach_count) >> 16)
-		cpu_relax();
-
-	cpumask_set_cpu(smp_processor_id(), mm_cpumask(mm));
-	set_user_asce(mm);
-	if (mm->context.flush_mm)
-		__tlb_flush_mm(mm);
-	preempt_enable();
+	load_kernel_asce();
+	if (mm) {
+		preempt_disable();
+		while (atomic_read(&mm->context.attach_count) >> 16)
+			cpu_relax();
+
+		cpumask_set_cpu(smp_processor_id(), mm_cpumask(mm));
+		if (mm->context.flush_mm)
+			__tlb_flush_mm(mm);
+		preempt_enable();
+	}
+	set_fs(current->thread.mm_segment);
 }
 
 #define enter_lazy_tlb(mm,tsk)	do { } while (0)

arch/s390/include/asm/switch_to.h

@@ -134,8 +134,4 @@ static inline void restore_access_regs(unsigned int *acrs)
 	prev = __switch_to(prev,next);					\
 } while (0)
 
-#define finish_arch_switch(prev) do {					     \
-	set_fs(current->thread.mm_segment);				     \
-} while (0)
-
 #endif /* __ASM_SWITCH_TO_H */

arch/s390/include/uapi/asm/ucontext.h

@@ -16,7 +16,9 @@ struct ucontext_extended {
 	struct ucontext  *uc_link;
 	stack_t		  uc_stack;
 	_sigregs	  uc_mcontext;
-	unsigned long	  uc_sigmask[2];
+	sigset_t	  uc_sigmask;
+	/* Allow for uc_sigmask growth.  Glibc uses a 1024-bit sigset_t.  */
+	unsigned char	  __unused[128 - sizeof(sigset_t)];
 	unsigned long	  uc_gprs_high[16];
 };
 
@@ -27,7 +29,9 @@ struct ucontext {
 	struct ucontext  *uc_link;
 	stack_t		  uc_stack;
 	_sigregs          uc_mcontext;
-	sigset_t	  uc_sigmask;	/* mask last for extensibility */
+	sigset_t	  uc_sigmask;
+	/* Allow for uc_sigmask growth.  Glibc uses a 1024-bit sigset_t.  */
+	unsigned char	  __unused[128 - sizeof(sigset_t)];
 };
 
 #endif /* !_ASM_S390_UCONTEXT_H */

arch/s390/kernel/compat_linux.h

@@ -69,7 +69,9 @@ struct ucontext32 {
 	__u32			uc_link;	/* pointer */	
 	compat_stack_t		uc_stack;
 	_sigregs32		uc_mcontext;
-	compat_sigset_t		uc_sigmask;	/* mask last for extensibility */
+	compat_sigset_t		uc_sigmask;
+	/* Allow for uc_sigmask growth.  Glibc uses a 1024-bit sigset_t.  */
+	unsigned char		__unused[128 - sizeof(compat_sigset_t)];
 };
 
 struct stat64_emu31;

arch/sparc/crypto/aes_glue.c

@@ -124,7 +124,7 @@ extern void aes_sparc64_ctr_crypt_256(const u64 *key, const u64 *input,
 				      u64 *output, unsigned int len,
 				      u64 *iv);
 
-struct aes_ops aes128_ops = {
+static struct aes_ops aes128_ops = {
 	.encrypt		= aes_sparc64_encrypt_128,
 	.decrypt		= aes_sparc64_decrypt_128,
 	.load_encrypt_keys	= aes_sparc64_load_encrypt_keys_128,
@@ -136,7 +136,7 @@ struct aes_ops aes128_ops = {
 	.ctr_crypt		= aes_sparc64_ctr_crypt_128,
 };
 
-struct aes_ops aes192_ops = {
+static struct aes_ops aes192_ops = {
 	.encrypt		= aes_sparc64_encrypt_192,
 	.decrypt		= aes_sparc64_decrypt_192,
 	.load_encrypt_keys	= aes_sparc64_load_encrypt_keys_192,
@@ -148,7 +148,7 @@ struct aes_ops aes192_ops = {
 	.ctr_crypt		= aes_sparc64_ctr_crypt_192,
 };
 
-struct aes_ops aes256_ops = {
+static struct aes_ops aes256_ops = {
 	.encrypt		= aes_sparc64_encrypt_256,
 	.decrypt		= aes_sparc64_decrypt_256,
 	.load_encrypt_keys	= aes_sparc64_load_encrypt_keys_256,

arch/sparc/include/asm/atomic_32.h

@@ -20,11 +20,11 @@
 
 #define ATOMIC_INIT(i)  { (i) }
 
-extern int __atomic_add_return(int, atomic_t *);
-extern int atomic_cmpxchg(atomic_t *, int, int);
+int __atomic_add_return(int, atomic_t *);
+int atomic_cmpxchg(atomic_t *, int, int);
 #define atomic_xchg(v, new) (xchg(&((v)->counter), new))
-extern int __atomic_add_unless(atomic_t *, int, int);
-extern void atomic_set(atomic_t *, int);
+int __atomic_add_unless(atomic_t *, int, int);
+void atomic_set(atomic_t *, int);
 
 #define atomic_read(v)          (*(volatile int *)&(v)->counter)
 

arch/sparc/include/asm/atomic_64.h

@@ -20,15 +20,15 @@
 #define atomic_set(v, i)	(((v)->counter) = i)
 #define atomic64_set(v, i)	(((v)->counter) = i)
 
-extern void atomic_add(int, atomic_t *);
-extern void atomic64_add(long, atomic64_t *);
-extern void atomic_sub(int, atomic_t *);
-extern void atomic64_sub(long, atomic64_t *);
+void atomic_add(int, atomic_t *);
+void atomic64_add(long, atomic64_t *);
+void atomic_sub(int, atomic_t *);
+void atomic64_sub(long, atomic64_t *);
 
-extern int atomic_add_ret(int, atomic_t *);
-extern long atomic64_add_ret(long, atomic64_t *);
-extern int atomic_sub_ret(int, atomic_t *);
-extern long atomic64_sub_ret(long, atomic64_t *);
+int atomic_add_ret(int, atomic_t *);
+long atomic64_add_ret(long, atomic64_t *);
+int atomic_sub_ret(int, atomic_t *);
+long atomic64_sub_ret(long, atomic64_t *);
 
 #define atomic_dec_return(v) atomic_sub_ret(1, v)
 #define atomic64_dec_return(v) atomic64_sub_ret(1, v)
@@ -107,6 +107,6 @@ static inline long atomic64_add_unless(atomic64_t *v, long a, long u)
 
 #define atomic64_inc_not_zero(v) atomic64_add_unless((v), 1, 0)
 
-extern long atomic64_dec_if_positive(atomic64_t *v);
+long atomic64_dec_if_positive(atomic64_t *v);
 
 #endif /* !(__ARCH_SPARC64_ATOMIC__) */

arch/sparc/include/asm/auxio.h

 #ifndef ___ASM_SPARC_AUXIO_H
 #define ___ASM_SPARC_AUXIO_H
+
+#ifndef __ASSEMBLY__
+
+extern void __iomem *auxio_register;
+
+#endif /* ifndef __ASSEMBLY__ */
+
 #if defined(__sparc__) && defined(__arch64__)
 #include <asm/auxio_64.h>
 #else

arch/sparc/include/asm/auxio_32.h

@@ -34,8 +34,8 @@
  * NOTE: these routines are implementation dependent--
  * understand the hardware you are querying!
  */
-extern void set_auxio(unsigned char bits_on, unsigned char bits_off);
-extern unsigned char get_auxio(void); /* .../asm/floppy.h */
+void set_auxio(unsigned char bits_on, unsigned char bits_off);
+unsigned char get_auxio(void); /* .../asm/floppy.h */
 
 /*
  * The following routines are provided for driver-compatibility
@@ -78,7 +78,7 @@ do { \
 
 
 /* AUXIO2 (Power Off Control) */
-extern __volatile__ unsigned char * auxio_power_register;
+extern volatile u8 __iomem *auxio_power_register;
 
 #define	AUXIO_POWER_DETECT_FAILURE	32
 #define	AUXIO_POWER_CLEAR_FAILURE	2

arch/sparc/include/asm/auxio_64.h

@@ -75,8 +75,6 @@
 
 #ifndef __ASSEMBLY__
 
-extern void __iomem *auxio_register;
-
 #define AUXIO_LTE_ON	1
 #define AUXIO_LTE_OFF	0
 
@@ -84,7 +82,7 @@ extern void __iomem *auxio_register;
  *
  * on - AUXIO_LTE_ON or AUXIO_LTE_OFF
  */
-extern void auxio_set_lte(int on);
+void auxio_set_lte(int on);
 
 #define AUXIO_LED_ON	1
 #define AUXIO_LED_OFF	0
@@ -93,7 +91,7 @@ extern void auxio_set_lte(int on);
  *
  * on - AUXIO_LED_ON or AUXIO_LED_OFF
  */
-extern void auxio_set_led(int on);
+void auxio_set_led(int on);
 
 #endif /* ifndef __ASSEMBLY__ */
 

arch/sparc/include/asm/bitext.h

@@ -20,8 +20,8 @@ struct bit_map {
 	int num_colors;
 };
 
-extern int bit_map_string_get(struct bit_map *t, int len, int align);
-extern void bit_map_clear(struct bit_map *t, int offset, int len);
-extern void bit_map_init(struct bit_map *t, unsigned long *map, int size);
+int bit_map_string_get(struct bit_map *t, int len, int align);
+void bit_map_clear(struct bit_map *t, int offset, int len);
+void bit_map_init(struct bit_map *t, unsigned long *map, int size);
 
 #endif /* defined(_SPARC_BITEXT_H) */

arch/sparc/include/asm/bitops_32.h

@@ -18,9 +18,9 @@
 #error only <linux/bitops.h> can be included directly
 #endif
 
-extern unsigned long ___set_bit(unsigned long *addr, unsigned long mask);
-extern unsigned long ___clear_bit(unsigned long *addr, unsigned long mask);
-extern unsigned long ___change_bit(unsigned long *addr, unsigned long mask);
+unsigned long ___set_bit(unsigned long *addr, unsigned long mask);
+unsigned long ___clear_bit(unsigned long *addr, unsigned long mask);
+unsigned long ___change_bit(unsigned long *addr, unsigned long mask);
 
 /*
  * Set bit 'nr' in 32-bit quantity at address 'addr' where bit '0'

arch/sparc/include/asm/bitops_64.h

@@ -15,12 +15,12 @@
 #include <asm/byteorder.h>
 #include <asm/barrier.h>
 
-extern int test_and_set_bit(unsigned long nr, volatile unsigned long *addr);
-extern int test_and_clear_bit(unsigned long nr, volatile unsigned long *addr);
-extern int test_and_change_bit(unsigned long nr, volatile unsigned long *addr);
-extern void set_bit(unsigned long nr, volatile unsigned long *addr);
-extern void clear_bit(unsigned long nr, volatile unsigned long *addr);
-extern void change_bit(unsigned long nr, volatile unsigned long *addr);
+int test_and_set_bit(unsigned long nr, volatile unsigned long *addr);
+int test_and_clear_bit(unsigned long nr, volatile unsigned long *addr);
+int test_and_change_bit(unsigned long nr, volatile unsigned long *addr);
+void set_bit(unsigned long nr, volatile unsigned long *addr);
+void clear_bit(unsigned long nr, volatile unsigned long *addr);
+void change_bit(unsigned long nr, volatile unsigned long *addr);
 
 #include <asm-generic/bitops/non-atomic.h>
 
@@ -30,8 +30,8 @@ extern void change_bit(unsigned long nr, volatile unsigned long *addr);
 
 #ifdef __KERNEL__
 
-extern int ffs(int x);
-extern unsigned long __ffs(unsigned long);
+int ffs(int x);
+unsigned long __ffs(unsigned long);
 
 #include <asm-generic/bitops/ffz.h>
 #include <asm-generic/bitops/sched.h>
@@ -41,10 +41,10 @@ extern unsigned long __ffs(unsigned long);
  * of bits set) of a N-bit word
  */
 
-extern unsigned long __arch_hweight64(__u64 w);
-extern unsigned int __arch_hweight32(unsigned int w);
-extern unsigned int __arch_hweight16(unsigned int w);
-extern unsigned int __arch_hweight8(unsigned int w);
+unsigned long __arch_hweight64(__u64 w);
+unsigned int __arch_hweight32(unsigned int w);
+unsigned int __arch_hweight16(unsigned int w);
+unsigned int __arch_hweight8(unsigned int w);
 
 #include <asm-generic/bitops/const_hweight.h>
 #include <asm-generic/bitops/lock.h>

arch/sparc/include/asm/btext.h

 #ifndef _SPARC_BTEXT_H
 #define _SPARC_BTEXT_H
 
-extern int btext_find_display(void);
+int btext_find_display(void);
 
 #endif /* _SPARC_BTEXT_H */

arch/sparc/include/asm/bug.h

@@ -5,7 +5,7 @@
 #include <linux/compiler.h>
 
 #ifdef CONFIG_DEBUG_BUGVERBOSE
-extern void do_BUG(const char *file, int line);
+void do_BUG(const char *file, int line);
 #define BUG() do {					\
 	do_BUG(__FILE__, __LINE__);			\
 	__builtin_trap();				\
@@ -20,6 +20,6 @@ extern void do_BUG(const char *file, int line);
 #include <asm-generic/bug.h>
 
 struct pt_regs;
-extern void die_if_kernel(char *str, struct pt_regs *regs) __attribute__ ((noreturn));
+void __noreturn die_if_kernel(char *str, struct pt_regs *regs);
 
 #endif

arch/sparc/include/asm/cacheflush_32.h

@@ -36,7 +36,7 @@
 #define flush_page_for_dma(addr) \
 	sparc32_cachetlb_ops->page_for_dma(addr)
 
-extern void sparc_flush_page_to_ram(struct page *page);
+void sparc_flush_page_to_ram(struct page *page);
 
 #define ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE 1
 #define flush_dcache_page(page)			sparc_flush_page_to_ram(page)
@@ -51,8 +51,8 @@ extern void sparc_flush_page_to_ram(struct page *page);
  * way the windows are all clean for the next process and the stack
  * frames are up to date.
  */
-extern void flush_user_windows(void);
-extern void kill_user_windows(void);
-extern void flushw_all(void);
+void flush_user_windows(void);
+void kill_user_windows(void);
+void flushw_all(void);
 
 #endif /* _SPARC_CACHEFLUSH_H */

arch/sparc/include/asm/cacheflush_64.h

@@ -10,7 +10,7 @@
 /* Cache flush operations. */
 #define flushw_all()	__asm__ __volatile__("flushw")
 
-extern void __flushw_user(void);
+void __flushw_user(void);
 #define flushw_user() __flushw_user()
 
 #define flush_user_windows flushw_user
@@ -30,29 +30,29 @@ extern void __flushw_user(void);
  * use block commit stores (which invalidate icache lines) during
  * module load, so we need this.
  */
-extern void flush_icache_range(unsigned long start, unsigned long end);
-extern void __flush_icache_page(unsigned long);
+void flush_icache_range(unsigned long start, unsigned long end);
+void __flush_icache_page(unsigned long);
 
-extern void __flush_dcache_page(void *addr, int flush_icache);
-extern void flush_dcache_page_impl(struct page *page);
+void __flush_dcache_page(void *addr, int flush_icache);
+void flush_dcache_page_impl(struct page *page);
 #ifdef CONFIG_SMP
-extern void smp_flush_dcache_page_impl(struct page *page, int cpu);
-extern void flush_dcache_page_all(struct mm_struct *mm, struct page *page);
+void smp_flush_dcache_page_impl(struct page *page, int cpu);
+void flush_dcache_page_all(struct mm_struct *mm, struct page *page);
 #else
 #define smp_flush_dcache_page_impl(page,cpu) flush_dcache_page_impl(page)
 #define flush_dcache_page_all(mm,page) flush_dcache_page_impl(page)
 #endif
 
-extern void __flush_dcache_range(unsigned long start, unsigned long end);
+void __flush_dcache_range(unsigned long start, unsigned long end);
 #define ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE 1
-extern void flush_dcache_page(struct page *page);
+void flush_dcache_page(struct page *page);
 
 #define flush_icache_page(vma, pg)	do { } while(0)
 #define flush_icache_user_range(vma,pg,adr,len)	do { } while (0)
 
-extern void flush_ptrace_access(struct vm_area_struct *, struct page *,
-				unsigned long uaddr, void *kaddr,
-				unsigned long len, int write);
+void flush_ptrace_access(struct vm_area_struct *, struct page *,
+			 unsigned long uaddr, void *kaddr,
+			 unsigned long len, int write);
 
 #define copy_to_user_page(vma, page, vaddr, dst, src, len)		\
 	do {								\

arch/sparc/include/asm/checksum_32.h

@@ -29,7 +29,7 @@
  *
  * it's best to have buff aligned on a 32-bit boundary
  */
-extern __wsum csum_partial(const void *buff, int len, __wsum sum);
+__wsum csum_partial(const void *buff, int len, __wsum sum);
 
 /* the same as csum_partial, but copies from fs:src while it
  * checksums
@@ -38,7 +38,7 @@ extern __wsum csum_partial(const void *buff, int len, __wsum sum);
  * better 64-bit) boundary
  */
 
-extern unsigned int __csum_partial_copy_sparc_generic (const unsigned char *, unsigned char *);
+unsigned int __csum_partial_copy_sparc_generic (const unsigned char *, unsigned char *);
 
 static inline __wsum
 csum_partial_copy_nocheck(const void *src, void *dst, int len, __wsum sum)

arch/sparc/include/asm/checksum_64.h

@@ -29,7 +29,7 @@
  *
  * it's best to have buff aligned on a 32-bit boundary
  */
-extern __wsum csum_partial(const void * buff, int len, __wsum sum);
+__wsum csum_partial(const void * buff, int len, __wsum sum);
 
 /* the same as csum_partial, but copies from user space while it
  * checksums
@@ -37,12 +37,12 @@ extern __wsum csum_partial(const void * buff, int len, __wsum sum);
  * here even more important to align src and dst on a 32-bit (or even
  * better 64-bit) boundary
  */
-extern __wsum csum_partial_copy_nocheck(const void *src, void *dst,
-					      int len, __wsum sum);
+__wsum csum_partial_copy_nocheck(const void *src, void *dst,
+				 int len, __wsum sum);
 
-extern long __csum_partial_copy_from_user(const void __user *src,
-					  void *dst, int len,
-					  __wsum sum);
+long __csum_partial_copy_from_user(const void __user *src,
+				   void *dst, int len,
+				   __wsum sum);
 
 static inline __wsum
 csum_partial_copy_from_user(const void __user *src,
@@ -59,9 +59,9 @@ csum_partial_copy_from_user(const void __user *src,
  *	Copy and checksum to user
  */
 #define HAVE_CSUM_COPY_USER
-extern long __csum_partial_copy_to_user(const void *src,
-					void __user *dst, int len,
-					  __wsum sum);
+long __csum_partial_copy_to_user(const void *src,
+				 void __user *dst, int len,
+				 __wsum sum);
 
 static inline __wsum
 csum_and_copy_to_user(const void *src,
@@ -77,7 +77,7 @@ csum_and_copy_to_user(const void *src,
 /* ihl is always 5 or greater, almost always is 5, and iph is word aligned
  * the majority of the time.
  */
-extern __sum16 ip_fast_csum(const void *iph, unsigned int ihl);
+__sum16 ip_fast_csum(const void *iph, unsigned int ihl);
 
 /* Fold a partial checksum without adding pseudo headers. */
 static inline __sum16 csum_fold(__wsum sum)
@@ -96,9 +96,9 @@ static inline __sum16 csum_fold(__wsum sum)
 }
 
 static inline __wsum csum_tcpudp_nofold(__be32 saddr, __be32 daddr,
-					       unsigned int len,
-					       unsigned short proto,
-					       __wsum sum)
+					unsigned int len,
+					unsigned short proto,
+					__wsum sum)
 {
 	__asm__ __volatile__(
 "	addcc		%1, %0, %0\n"
@@ -116,9 +116,9 @@ static inline __wsum csum_tcpudp_nofold(__be32 saddr, __be32 daddr,
  * returns a 16-bit checksum, already complemented
  */
 static inline __sum16 csum_tcpudp_magic(__be32 saddr, __be32 daddr,
-						   unsigned short len,
-						   unsigned short proto,
-						   __wsum sum)
+					unsigned short len,
+					unsigned short proto,
+					__wsum sum)
 {
 	return csum_fold(csum_tcpudp_nofold(saddr,daddr,len,proto,sum));
 }

arch/sparc/include/asm/cmpxchg_32.h

@@ -20,7 +20,7 @@ static inline unsigned long xchg_u32(__volatile__ unsigned long *m, unsigned lon
 	return val;
 }
 
-extern void __xchg_called_with_bad_pointer(void);
+void __xchg_called_with_bad_pointer(void);
 
 static inline unsigned long __xchg(unsigned long x, __volatile__ void * ptr, int size)
 {
@@ -45,9 +45,9 @@ static inline unsigned long __xchg(unsigned long x, __volatile__ void * ptr, int
 #define __HAVE_ARCH_CMPXCHG	1
 
 /* bug catcher for when unsupported size is used - won't link */
-extern void __cmpxchg_called_with_bad_pointer(void);
+void __cmpxchg_called_with_bad_pointer(void);
 /* we only need to support cmpxchg of a u32 on sparc */
-extern unsigned long __cmpxchg_u32(volatile u32 *m, u32 old, u32 new_);
+unsigned long __cmpxchg_u32(volatile u32 *m, u32 old, u32 new_);
 
 /* don't worry...optimizer will get rid of most of this */
 static inline unsigned long

arch/sparc/include/asm/cmpxchg_64.h

@@ -42,7 +42,7 @@ static inline unsigned long xchg64(__volatile__ unsigned long *m, unsigned long
 
 #define xchg(ptr,x) ((__typeof__(*(ptr)))__xchg((unsigned long)(x),(ptr),sizeof(*(ptr))))
 
-extern void __xchg_called_with_bad_pointer(void);
+void __xchg_called_with_bad_pointer(void);
 
 static inline unsigned long __xchg(unsigned long x, __volatile__ void * ptr,
 				       int size)
@@ -91,7 +91,7 @@ __cmpxchg_u64(volatile long *m, unsigned long old, unsigned long new)
 
 /* This function doesn't exist, so you'll get a linker error
    if something tries to do an invalid cmpxchg().  */
-extern void __cmpxchg_called_with_bad_pointer(void);
+void __cmpxchg_called_with_bad_pointer(void);
 
 static inline unsigned long
 __cmpxchg(volatile void *ptr, unsigned long old, unsigned long new, int size)

arch/sparc/include/asm/cpudata.h

 #ifndef ___ASM_SPARC_CPUDATA_H
 #define ___ASM_SPARC_CPUDATA_H
+
+#ifndef __ASSEMBLY__
+
+#include <linux/threads.h>
+#include <linux/percpu.h>
+
+extern const struct seq_operations cpuinfo_op;
+
+#endif /* !(__ASSEMBLY__) */
+
 #if defined(__sparc__) && defined(__arch64__)
 #include <asm/cpudata_64.h>
 #else

arch/sparc/include/asm/cpudata_64.h

@@ -8,9 +8,6 @@
 
 #ifndef __ASSEMBLY__
 
-#include <linux/percpu.h>
-#include <linux/threads.h>
-
 typedef struct {
 	/* Dcache line 1 */
 	unsigned int	__softirq_pending; /* must be 1st, see rtrap.S */
@@ -35,8 +32,6 @@ DECLARE_PER_CPU(cpuinfo_sparc, __cpu_data);
 #define cpu_data(__cpu)		per_cpu(__cpu_data, (__cpu))
 #define local_cpu_data()	__get_cpu_var(__cpu_data)
 
-extern const struct seq_operations cpuinfo_op;
-
 #endif /* !(__ASSEMBLY__) */
 
 #include <asm/trap_block.h>

arch/sparc/include/asm/delay_32.h

@@ -20,8 +20,8 @@ static inline void __delay(unsigned long loops)
 }
 
 /* This is too messy with inline asm on the Sparc. */
-extern void __udelay(unsigned long usecs, unsigned long lpj);
-extern void __ndelay(unsigned long nsecs, unsigned long lpj);
+void __udelay(unsigned long usecs, unsigned long lpj);
+void __ndelay(unsigned long nsecs, unsigned long lpj);
 
 #ifdef CONFIG_SMP
 #define __udelay_val	cpu_data(smp_processor_id()).udelay_val

arch/sparc/include/asm/delay_64.h

@@ -8,8 +8,8 @@
 
 #ifndef __ASSEMBLY__
 
-extern void __delay(unsigned long loops);
-extern void udelay(unsigned long usecs);
+void __delay(unsigned long loops);
+void udelay(unsigned long usecs);
 #define mdelay(n)	udelay((n) * 1000)
 
 #endif /* !__ASSEMBLY__ */

arch/sparc/include/asm/device.h

@@ -19,7 +19,7 @@ struct dev_archdata {
 	int			numa_node;
 };
 
-extern void of_propagate_archdata(struct platform_device *bus);
+void of_propagate_archdata(struct platform_device *bus);
 
 struct pdev_archdata {
 	struct resource		resource[PROMREG_MAX];