Merge tag 'tegra-for-4.12-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next

Pull Tegra clk driver updates from Thierry Reding:

This contains a bunch of fixes and cleanups, mostly to the Tegra210
clock driver.

* tag 'tegra-for-4.12-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (24 commits)
  clk: tegra: Don't reset PLL-CX if it is already enabled
  clk: tegra: Add missing Tegra210 clocks
  clk: tegra: Propagate clk_out_x rate to parent
  clk: tegra: Fix build warnings on Tegra20/Tegra30
  clk: tegra: Mark TEGRA210_CLK_DBGAPB as always on
  clk: tegra: Add SATA seq input control
  clk: tegra: Add Tegra210 special resets
  clk: tegra: Rework pll_u
  clk: tegra: Implement reset control reset
  clk: tegra: Fix disable unused for clocks sharing enable bit
  clk: tegra: Handle UTMIPLL IDDQ
  clk: tegra: Add aclk
  clk: tegra: Add super clock mux/divider
  clk: tegra: Define Tegra210 DMIC clocks
  clk: tegra: Fix constness for peripheral clocks
  clk: tegra: Define Tegra210 DMIC sync clocks
  clk: tegra: Add CEC clock
  clk: tegra: Fix type for m field
  clk: tegra: Correct tegra210_pll_fixed_mdiv_cfg rate calculation
  clk: tegra: Don't warn for PLL defaults unnecessarily
  ...

Thus CS2000 datasheet is indicating below, this patch
follows it.

WARNING: All "Reserved" registers must maintain their default
         state to ensure proper functional operation.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Fix a typo which caused both vfe0 and vfe1 powerdomains to be
named as vfe0.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Fixes: 7e824d50 ("clk: qcom: gdsc: Add mmcc gdscs for msm8996 family")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Use a classic polling to test bit ready.
And the shift of the bit ready of LSE & LSI were wrongs.

Fixes: 861adc44 ("clk: stm32f4: Add LSI & LSE clocks")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Remove the redundant check of 'rate' in the if statement of the
'pll_set_rate' function
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Fixes: 5fe225c1 ("clk: iproc: add initial common clock support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Merge tag 'v4.12-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next

Pull rockchip clk driver updates from Heiko Stuebner:

  General rockchip clock changes for 4.12. Contains some new clock-ids
  as well as fixups of the clock-ids on rk3368 timers, which were unused
  and completely wrong (more and differently named timers).
  Also there is one new clock on rk3328 using the muxgrf type, a fix for
  pll enablement which should wait for the pll to lock before continuing,
  some more critical clocks and the rename of the rk1108 to rv1108, as the
  soc seems to have been using a preliminary name before its actual release.
  The plan is to have the driver changes (pinctrl, clk) go through the
  respective maintainer trees and once everything landed in mainline do
  the rename of the devicetree files. With the dts-include change in the
  clock rename, we also keep everything compiling and thus bisectability.

* tag 'v4.12-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  clk: rockchip: add pll_wait_lock for pll_enable
  clk: rockchip: rename RK1108 to RV1108
  dt-bindings: rk1108-cru: rename RK1108 to RV1108
  clk: rockchip: mark some rk3368 core-clks as critical
  clk: rockchip: export SCLK_TIMERXX id for timers on rk3368
  clk: rockchip: describe clk_gmac using the new muxgrf type on rk3328
  clk: rockchip: add clock ids for timer10-15 of RK3368 SoCs
  clk: rockchip: fix up rk3368 timer-ids
  clk: rockchip: add rk3328 clk_mac2io_ext ID
  clk: rockchip: Set "ignore unused" for PMU M0 clocks on rk3399

Merge tag 'clk-renesas-for-v4.12-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next

Pull Renesas clk driver updates from Geert Uytterhoeven:

  - Add support for the Clock Pulse Generator / Module Standby and
    Software Reset module on revision ES2.0 of the R-Car H3 SoC, which
    differs from ES1.x in some areas.
  - Add IMR clocks for R-Car H3 and M3-W,
  - Add workaround for PLL0/2/4 errata on R-Car H3 ES1.0,
  - Small fixes and cleanups.

* tag 'clk-renesas-for-v4.12-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
  clk: renesas: rcar-gen3-cpg: Add support for RCLK on R-Car H3 ES2.0
  clk: renesas: r8a7795: Add support for R-Car H3 ES2.0
  clk: renesas: Add r8a7795 ES2.0 CPG Core Clock Definitions
  clk: renesas: cpg-mssr: Add support for fixing up clock tables
  clk: renesas: rcar-gen3: Add workaround for PLL0/2/4 errata on H3 ES1.0
  clk: renesas: rcar-gen3-cpg: Pass mode pins to rcar_gen3_cpg_init()
  clk: renesas: r8a7796: Reformat core clock table
  clk: renesas: r8a7795: Reformat core clock table
  clk: renesas: r8a7796: Correct name of watchdog clock
  clk: renesas: r8a7795: Correct name of watchdog clock
  clk: renesas: r8a7795: Correct parent clock and sort order for Audio DMACs
  clk: renesas: r8a7796: Add IMR clocks
  clk: renesas: r8a7795: Add IMR clocks

* clk-fixes:
  clk: stm32f4: fix: exclude values 0 and 1 for PLLQ

0000: PLLQ = 0, wrong configuration
0001: PLLQ = 1, wrong configuration
...
0010: PLLQ = 2
0011: PLLQ = 3
0100: PLLQ = 4
...
1111: PLLQ = 1

Use divider table to exclude 0 and 1 values.

Fixes: 83135ad3 ("clk: stm32f4: Add PLL_I2S & PLL_SAI for STM32F429/469 boards")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

* 'for-4.12-ti-clk-cleanups' of https://github.com/t-kristo/linux-pm:
  clk: ti: convert to use proper register definition for all accesses
  clk: ti: dpll44xx: fix clksel register initialization
  clk: ti: gate: export gate_clk_ops locally
  clk: ti: divider: add driver internal API for parsing divider data
  clk: ti: divider: convert TI divider clock to use its own data representation
  clk: ti: mux: convert TI mux clock to use its internal data representation
  clk: ti: drop unnecessary MEMMAP_ADDRESSING flag
  clk: ti: omap4: cleanup unnecessary clock aliases
  clk: ti: enforce const types on string arrays
  clk: ti: move omap2_init_clk_clkdm under TI clock driver
  clk: ti: add clkdm_lookup to the exported functions
  clk: ti: use automatic clock alias generation framework
  clk: ti: add API for creating aliases automatically for simple clock types
  clk: ti: add support for automatic clock alias generation
  clk: ti: remove un-used definitions from public clk_hw_omap struct

The debug APB clock is absent in hi6220 driver, so this patch is to add
support for it.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Commit 8dce89a1 ("clk: tegra: Don't warn for PLL defaults
unnecessarily") changed the tegra210_pllcx_set_defaults() function
causing the PLL to always be reset regardless of whether it is in-use.
This function was changed so that resetting of the PLL will only be
skipped if the PLL is enabled AND 'pllcx->params->defaults_set' is not
true. However, the 'pllcx->params->defaults_set' is always true and
hence, the PLL is now always reset. This causes the boot to fail on the
Tegra210 Smaug where the PLL is already enabled and in-use. Fix this by
only resetting the PLL if not in-use and only printing the warning that
the defaults are not set after we have checked the default settings.

Fixes: 8dce89a1 ("clk: tegra: Don't warn for PLL defaults unnecessarily")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

iqc1, iqc2, tegra_clk_pll_a_out_adsp, tegra_clk_pll_a_out0_out_adsp, adsp
and adsp neon were not modelled. dp2 wasn't modelled for Tegra210.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Given that externx can only be used as a parent for clk_out_x, it makes
sense to propagate requests to make clk_out_x easier to handle.
Signed-off-by: Alex Frid <afrid@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Starting with R-Car H3 ES2.0, the parent of RCLK is selected using MD28.

Add support for that, but retain the old behavior for R-Car H3 ES1.x and
M3-W ES1.0 using a quirk.

Inspired by a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>

The Clock Pulse Generator / Module Standby and Software Reset module in
R-Car H3 ES2.0 differs from ES1.x in the following areas:
  - More core clocks (S0D2, S0D3, S0D6, S0D8, S0D12),
  - Different parent clocks for AUDMAC, EtherAVB, FCP, FDP, IMR,
    SYS-DMAC, VIN, VSPB, VSPI,
  - Removal of modules CSI21, FCPCI, FCPF2, FCPVD3, FCPVI2, FDP1-2,
    USB3-IF1, VSPD3, VSPI2,
  - Addition of modules EHCI3, HS-USB-IF3, USB-DMAC3-0, USB-DMAC3-1.

The goal is twofold:
  1. Support both the ES1.x and ES2.0 SoC revisions in a single binary
     for now,
  2. Make it clear which code supports ES1.x, so it can easily be
     identified and removed later, when production SoCs are deemed
     ubiquitous.

This is achieved by:
  - Updating the clock tables for the latest revision (ES2.0), but not
    removing clocks that only exist on earlier revisions (ES1.x),
  - Detecting the SoC revision at runtime using the new soc_device_match()
    API, and fixing up the clocks tables to match the actual SoC
    revision, by:
      - NULLifying core and module clocks of modules that do not exist,
      - Reparenting module clocks that have a different parent on ES1.x.

Based on R-Car Gen3 Hardware User's Manual rev. 0.53E.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add all R-Car H3 ES2.0 Clock Pulse Generator Core Clock Outputs, as
listed in Table 8.2a ("List of Clocks [R-Car H3]") of the R-Car Gen3
Hardware User's Manual rev. 0.53E.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

The same SoC may have different clocks and/or module clock parents,
depending on SoC revision.  One option is to use different sets of clock
tables for each SoC revision.  However, if the differences are small, it
is much more space-efficient to have a single set of clock tables, and
fix those up at runtime instead.

Hence provide three helpers:
  - Two helpers to NULLify core and module clocks that do not exist on
    some revisions (NULLified clocks are skipped during the registration
    phase),
  - One helper to reparent module clocks that have different clock
    parents.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Merge tag 'sunxi-clk-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-fixes

Pull Allwinner clock fixes from Maxime Ripard:

A few fixes for a bunch of clocks on a few SoCs. The most important one is
probably one that fixes the NKMP clock frequency calculation and could end
up with clocking the CPU frequency to out of bounds rates.

* tag 'sunxi-clk-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  clk: sunxi-ng: fix recalc_rate formula of NKMP clocks
  clk: sunxi-ng: Fix div/mult settings for osc12M on A64
  clk: sunxi-ng: sun6i: Fix enable bit offset for hdmi-ddc module clock
  clk: sunxi: ccu-sun5i needs nkmp
  clk: sunxi-ng: mp: Adjust parent rate for pre-dividers

If pll is power down,when power up pll need wait pll lock.
The reference documents section:
	PLL frequency change and lock check
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Rockchip finally named the SOC as RV1108, so change it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>

[include rename in rk1108.dtsi to prevent compile errors]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Rockchip finally named the SOC as RV1108, so change it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add a workaround for errata on R-Car H3 ES1.0, where the PLL0, PLL2, and
PLL4 clock frequencies are off by a factor of two.

Inspired by a patch by Dien Pham in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Dien Pham <dien.pham.ry@renesas.com>

Pass the mode pin states from the SoC-specific CPG/MSSR driver to the
R-Car Gen3 CPG driver core, as their state will be needed to make some
core clock configuration decisions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

For easier comparison with other clock drivers.
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

For easier comparison with other clock drivers.
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

There's only a single watchdog clock, and it's named "rwdt".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

There's only a single watchdog clock, and it's named "rwdt".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

The parent clock of the Audio DMACs is the "ZS" AXI bus clock, which
maps to S3D1 on R-Car H3 ES1.x.
All module clocks must be sorted by clock ID.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

The recent conversion of proper const usage was only partial and didn't
include Tegra20 and Tegra30 support. Fix that up.
Signed-off-by: Thierry Reding <treding@nvidia.com>

This is needed to make the JTAG debugging interface work.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
[treding@nvidia.com: add TODO comment]
Signed-off-by: Thierry Reding <treding@nvidia.com>

This will be used by the powergating driver to ensure proper sequencer
state when the SATA domain is powergated.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Tegra210 has 2 special resets which don't follow the normal pattern:
DVCO and ADSP. Add them in this patch.

Changelog:

v2: add DT bindings file
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

In normal operation pll_u is under hardware control and has a fixed rate
of 480MHz. Hardware will turn on pll_u on whenever any of the XUSB
powerdomains is on. From a software point of view we model this is if
pll_u is always on using a fixed rate clock. However the bootloader
might or might not have configured pll_u this way. So we will check the
current state of pll_u at boot and reconfigure it if required.

There are 3 possiblities at kernel boot:
1) pll_u is under hardware control: do nothing
2) pll_u is under hardware control and enabled: enable hardware control
3) pll_u is disabled: enable pll_u and enable hardware control

In all cases we also check if UTMIPLL is under hardware control at boot
and configure it for hardware control if that is not the case.
The same is done during SC7 resume.

Thanks to Joseph Lo <josephl@nvidia.com> for bug fixes.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

For completeness, also implement this reset framework API for Tegra.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Arto Merilainen <amerilainen@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

In case 2 clocks share an enable bit and one of them is enabled by a
driver and the other one is not, CCF will think it's enabled because it
will only look at the HW state. Therefore it will disable the clock and
thus also disable the other clock which was enabled. Solve this by
reading the initial state of the enable bit and incrementing the
refcount if it's set.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Export UTMIPLL IDDQ functions. These will be needed when powergating the
XUSB partition.
Signed-off-by: BH Hsieh <bhsieh@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This clock clocks the ADSP Cortex-A9.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add a super clock type which implements both mux and divider. This is
used for aclk.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Tegra210 has 3 inputs for Digital Microphones (DMICs). Provide the
required clocks for them.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>