- 29 Sep, 2012 40 commits
-
-
Huang Shijie authored
The default frequencies of the extra clocks are 200MHz. The current code sets the extra clocks to 44.5MHz. When i add the EDO feature to gpmi, i have to revert the extra clocks to 200MHz. So it is better that we do not set the default values for the extra clocks. The driver runs well even when we do not set the default values for extra clocks. Signed-off-by:
Huang Shijie <b32955@freescale.com> Signed-off-by:
Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com>
-
Huang Shijie authored
The setting DLL code is a little mess. Just simplify the code and the comments. Signed-off-by:
-
Huang Shijie authored
add the WRN_DLY_SEL field for HW_GPMI_CTRL1. This field is used as delay for gpmi write strobe. Signed-off-by:
-
Huang Shijie authored
The current code will gets the clock frequency which is used by gpmi_nfc_compute_hardware_timing(). It makes the code a little mess. So move the `get clock frequency` code to the gpmi_nfc_compute_hardware_timing() itself. This makes the code tidy and clean. This patch also uses the macro NSEC_PER_SEC to replace the `1000000000`. Signed-off-by:
-
Huang Shijie authored
The gpmi_nfc_compute_hardware_timing{} should contains all the fields setting for gpmi timing registers. It already contains the fields for HW_GPMI_TIMING0 and HW_GPMI_CTRL1. So it is better to add a new field setting for HW_GPMI_TIMING1 in this data structure. This makes the code more clear in logic. This patch also changes some comments to make the code more readable. Signed-off-by: -
Huang Shijie authored
add onfi_get_async_timing_mode() to get the supportted asynchronous timing mode. add onfi_get_sync_timing_mode() to get the supportted synchronous timing mode. Also add the neccessary macros : the timing modes. Signed-off-by:
-
Huang Shijie authored
Add the set-features(0xef)/get-features(0xee) helpers for ONFI nand. Also add the necessary macros. Signed-off-by:
-
Kim Phillips authored
drivers/mtd/nand/fsl_ifc_nand.c:196:34: warning: cast removes address space of expression [sparse] drivers/mtd/nand/fsl_ifc_nand.c:196:34: warning: incorrect type in initializer (different address spaces) [sparse] drivers/mtd/nand/fsl_ifc_nand.c:196:34: expected unsigned int [noderef] [usertype] <asn:2>*mainarea [sparse] drivers/mtd/nand/fsl_ifc_nand.c:196:34: got unsigned int [usertype] *<noident> [sparse] ... Signed-off-by:
Kim Phillips <kim.phillips@freescale.com> Signed-off-by:
-
Richard Genoud authored
If override size is too big, the module was actually loaded instead of failing, because retval was not set. This lead to memory corruption with the use of the freed structs nandsim and nand_chip. Cc: stable@vger.kernel.org Signed-off-by:
Richard Genoud <richard.genoud@gmail.com> Signed-off-by:
-
Mike Dunn authored
Currently the docg4's ecc.read_page() method returns -EBADMSG when uncorrectable bitflips occur. This is wrong; 0 should be returned in this case. An error code should only be returned by this method in the case of a hardware error (probably -EIO). Signed-off-by:
Mike Dunn <mikedunn@newsguy.com> Acked-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Richard Genoud authored
In nand_bbt.c, a hardcoded value was used instead of the define meant for that, so we use the define. There's no functional change. Signed-off-by:
-
Christian Daudt authored
This driver is being removed as part of the cleanup of the bcmring SoC from mainline as it is no longer maintained. Signed-off-by:
Christian Daudt <csd@broadcom.com> Reviewed-by:
Jiandong Zheng <jdzheng@broadcom.com> Acked-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Mike Dunn authored
In the absence of any formal documentation of the nand interface, I thought this patch to the header file might be helpful. Signed-off-by:
-
m-karicheri2@ti.com authored
As a first step towards migrating davinci platforms to use common clock framework, replace all instances of clk_enable() with clk_prepare_enable() and clk_disable() with clk_disable_unprepare(). Until the platform is switched to use the CONFIG_HAVE_CLK_PREPARE Kconfig variable, this just adds a might_sleep() call and would work without any issues. This will make it easy later to switch to common clk based implementation of clk driver from DaVinci specific driver. Signed-off-by:
Murali Karicheri <m-karicheri2@ti.com> Reviewed-by:
Mike Turquette <mturquette@linaro.org> Acked-by:
-
Akinobu Mita authored
This adds the double bit error detection test cases listed below: * Prepare data block with double bit error and ECC data without corruption, and verify that the uncorrectable error is detected by __nand_correct_data(). * Prepare data block with single bit error and ECC data with single bit error, and verify that the uncorrectable error is detected. * Prepare data block without corruption and ECC data with double bit error, and verify that the uncorrectable error is detected. Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Akinobu Mita authored
This adds the single bit error correction test case listed below: Prepare data block without corruption and ECC data with single bit error, and verify that the data block is preserved by __nand_correct_data(). Signed-off-by:
-
Akinobu Mita authored
This adds no corruptin test case listed below: Prepare data block and ECC data with no corruption, and verify that the data block is preserved by __nand_correct_data() Signed-off-by:
-
Akinobu Mita authored
This rewrites the entire test routine in order to make it easy to add more tests by later changes and minimize duplication of each tests as much as possible. Now that each test is described by the members of struct nand_ecc_test: - name: descriptive testname - prepare: function to prepare data block and ecc with artifical corruption - verify: function to verify the result of correcting data block Signed-off-by:
-
Akinobu Mita authored
Currently inject_single_bit_error() is used to inject single bit error into randomly selected bit position of the 256 or 512 bytes data block. Later change will add tests which inject bit errors into the ecc code. Unfortunately, inject_single_bit_error() doesn't work for the ecc code which is not a multiple of sizeof(unsigned long). Because bit fliping at random position is done by __change_bit(). For example, flipping bit position 0 by __change_bit(0, addr) modifies 3rd byte (32bit) or 7th byte (64bit) on big-endian systems. Using little-endian version of bitops can fix this issue. But little-endian version of __change_bit is not yet available. So this defines __change_bit_le() locally in a similar fashion to asm-generic/bitops/le.h and use it. Signed-off-by:
-
Iwo Mergler authored
This tests ECC biterror recovery on a single NAND page. Mostly intended to test ECC hardware and low-level NAND driver. There are two test modes: 0 - artificially inserting bit errors until the ECC fails This is the default method and fairly quick. It should be independent of the quality of the FLASH. 1 - re-writing the same pattern repeatedly until the ECC fails. This method relies on the physics of NAND FLASH to eventually generate '0' bits if '1' has been written sufficient times. Depending on the NAND, the first bit errors will appear after 1000 or more writes and then will usually snowball, reaching the limits of the ECC quickly. The test stops after 10000 cycles, should your FLASH be exceptionally good and not generate bit errors before that. Try a different page offset in that case. Please note that neither of these tests will significantly 'use up' any FLASH endurance. Only a maximum of two erase operations will be performed. Signed-off-by:Iwo Mergler <Iwo.Mergler@netcommwireless.com.au> Signed-off-by:
-
Shmulik Ladkani authored
Huang Shijie <shijie8@gmail.com> explains: Assume we have a 1GiB(8Gib) NAND chip, and we set the partitions in the command line like this: #gpmi-nand:100m(boot),100m(kernel),1g(rootfs) In this case, the partition truncating occurs. The current code will get the following result: ---------------------------------- root@freescale ~$ cat /proc/mtd dev: size erasesize name mtd0: 06400000 00040000 "boot" mtd1: 06400000 00040000 "kernel" ---------------------------------- It is obvious that we lost the truncated partition `rootfs` which should be 824MiB in this case. Also, forbid 0-sized partitions. Signed-off-by:Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by:
-
Sachin Kamat authored
module_platform_driver simplifies the code by eliminating module_init and module_exit calls. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by:
-
Fabio Estevam authored
With the new i.mx clock framework the mxc_nand clock is registered as: clk_register_clkdev(clk[nfc_gate], NULL, "mxc_nand");0") So we do not need to pass "nfc" string and can use NULL instead. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Fabio Estevam authored
Using module_platform_driver() makes the code smaller and cleaner. Signed-off-by:
-
Fabio Estevam authored
Using module_platform_driver() makes the code smaller and cleaner. Signed-off-by:
Marek Vasut <marex@denx.de> Signed-off-by:
-
Fabio Estevam authored
Improve logging style by prefixing the pr_ messages with "gpmi_nand". Signed-off-by:
-
Marek Vasut authored
Quoting from the datasheet for S25FL064P, rev. 05, Nov 18 2011, § 9.17: "A 64 kB[sic] sector erase (D8h) command issued on 4 kB or 8 kB erase sectors will erase all sectors in the specified 64 kB region. However, please note that a 4 kB sector erase (20h) or 8 kB sector erase (40h) command will not work on a 64 kB sector." Referring further to Table 8.1 and Table 8.2, it is clearly seen that most of the sectors are 64KiB; therefore disable this 4KiB erase support since it's valid only on first/last sectors. Signed-off-by:
-
Rafał Miłecki authored
This registers MTD driver for serial flash platform device. Right now it supports reading only, writing still has to be implemented. Artem: minor amendments. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
David Woodhouse authored
Merge commit '371a0044' of 'git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next.git' We need the following 2 patches from the 'net-next' tree for the BCMA flash driver: 371a0044 bcma: detect and register NAND flash device d57ef3a6 bcma: detect and register serial flash device and this is why we are merging the net-next tree (presumably persistent) up to commit '371a0044'. Signed-off-by:
-
Akinobu Mita authored
Currently the data blocks which is used to test single bit error correction is allocated statically and injecting single bit error is implemented by using __change_bit() which must operate on the memory aligned to the size of an "unsigned long". But there is no such guarantee for statically allocated array. This fix the issue by allocating the data block dynamically by kmalloc(). It also allocate the ecc code dynamically instead of allocating statically on stack. The reason to allocate the ecc code dynamically is that later change will add tests which inject bit errors into the ecc code by bitops. Signed-off-by:
-
Akinobu Mita authored
This includes the message related changes: - Use pr_* instead of printk - Print hexdump of ECC code if test fails - Change log level for hexdump of data from KERN_DEBUG to KERN_INFO - Factor out the hexdump code into a separate function Signed-off-by:
-
Akinobu Mita authored
Return -EINVAL instead of -1 (-EPERM) when test fails. Signed-off-by:
-
Akinobu Mita authored
Including linux/jiffies.h was required for calling srandom32(jiffies) that has already been removed. Signed-off-by:
-
Brian Norris authored
JFFS2 was designed without thought for OOB bitflips, it seems, but they can occur and will be reported to JFFS2 via mtd_read_oob()[1]. We don't want to fail on these transactions, since the data was corrected. [1] Few drivers report bitflips for OOB-only transactions. With such drivers, this patch should have no effect. Signed-off-by: -
Julia Lawall authored
devm free functions should not have to be explicitly used. Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Artem Bityutskiy authored
Clean-up the driver a bit to make it easier to read and amend the coding style. Mostly these are changes like: if (a) { } => if (a) { } Some extra blank lines were added. Indentation was changed to use tabs instead of spaces. Signed-off-by: -
Artem Bityutskiy authored
This patch revises and fixes error handling in the command line mtd partitions parser. Namely: 1. we ignored return code of 'mtdpart_setup_real()'. 2. instead of returning 0 for failure and 1 for success, teach 'mtdpart_setup_real()' to return real error codes. Signed-off-by:
-
Rafał Miłecki authored
This driver provides parser detecting partitions on BCM47XX flash memories. It has many differences in comparison to BCM63XX, like: 1) Different CFE with no more trivial MAGICs 2) More partitions types (board_data, ML, POT) 3) Supporting more than 1 flash on a device which resulted in decision of writing new parser. It uses generic mtd interface and was successfully tested with Netgear WNDR4500 router which has 2 flash memories: serial one and NAND one. Signed-off-by:
-
Artem Bityutskiy authored
We do not have to initialize variables for .bss to 0 in Linux. Signed-off-by:
-
Andreas Bießmann authored
Unloading the omap2 nand driver missed to release the memory region which will result in not being able to request it again if one want to load the driver later on. This patch fixes following error when loading omap2 module after unloading: ---8<--- ~ $ rmmod omap2 ~ $ modprobe omap2 [ 37.420928] omap2-nand: probe of omap2-nand.0 failed with error -16 ~ $ --->8--- This error was introduced in 67ce04bf which was the first commit of this driver. Signed-off-by:
Andreas Bießmann <andreas@biessmann.de> Cc: stable@vger.kernel.org Signed-off-by:
-
